Spectra Series Operation Manual.indd

Spectra Series Operation Manual.indd
O P E R AT I O N M a n u a l
Spectra Series
Spectra Series
Programming
Manual
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
1
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
Table of Contents
Safety Instructions
Page 3
Features
Page 4
Operation
Page 5
DMX Mode
Page 6
Personalities
Page 7
Resolution
Page 8
Stand Alone Mode
Page 9
Fixed Color Mode
Page 10
Master Mode
Page 11
Spectra Strip Operation
Page 12
•Menu Navigation
Page 13
•Control Mode & Preset Selection Page 14
•DMX & SHOW mode Operation Page 15
•Fixture Lock & Test
Page 16
•Reset to Factory Defaults
Page 16
•Preset Configurations
Page 17
•Interpolation Curves
Page 18
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
2
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF
FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS FOR SPECTRA SERIES LED
LIGHTING FIXTURES.
INSTRUCTIONS DE SÛRETÉ
LES INSTRUCTIONS AU SUJET D’UN
RISQUE D’INCENDIE LE CHOC
ÉLECTRIQUE, OU LA BLESSURE AUX
PERSONNES POUR SS-CYC-100.
WARNING! - TO REDUCE THE RISK OF FIRE, ELECTRIC AVERTISSEMENT! - POUR RÉDUIRE LE RISQUE
SHOCK, OR INJURY TO PERSONS, FOLLOW THESE D’INCENDIE, LE CHOC ÉLECTRIQUE, OU LA BLESSURE
IMPORTANT SAFETY INSTRUCTIONS:
AUX PERSONNES, SUIVRE CES INSTRUCTIONS DE
SÉCURITÉ IMPORTANTES:
1. Turn off, unplug power, and allow fixture to cool
1. Éteignez, débranchez la puissance, et permettez
before cleaning or servicing.
au montage de se refroidir avant le nettoyage ou
2. Ensure that fixture is properly grounded.
l’entretien.
3. Ensure that ventilation slots are not obstructed.
2. Assurez-vous que le montage est correctement
4. Do not look directly at lighted LEDs.
relié à la terre.
5. Keep away from flammable materials.
3. Assurez-vous que des fentes de ventillation ne
6. No user serviceable parts inside. Replace entire
sont pas obstruées.
LED assembly.
7. Do not touch the LEDs at any time. Use a soft lint 4. Ne regardez pas directement la LED allumée.
5. S’éloigner des materiaux inflammables.
free cloth to clean lens. Do not use solvents to
6. Aucunes pièces utiles d’utilisateur à l’intérieur.
clean. Use cloth dampened with water. Allow to
Remplacez la LED entière.
dry completely before reenergizing.
7. Ne touchez pas les voyants à tout moment. Utilisez
8. Do not operate the unit with a missing or
un chiffon doux non pelucheux pour nettoyer la
damaged lens.
lentille. Ne pas utiliser de solvants pour nettoyer.
Chiffon humidifié avec de l’eau utilisation. Laisser
----------SAVE THESE INSTRUCTIONS!----------sécher complètement avant de redynamisation.
8. Ne pas faire fonctionner l’appareil avec un
diffuseur antérieur ou une lampe.
----------GARDER CES INSTRUCTIONS!----------
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
3
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
Features
The SPECTRA SERIES LED lighting fixtures are the first of its kind in the Theatrical and Architectural Lighting
Industry offered by Altman Lighting.
•
Compatible with DMX512 and RDM protocols.
•
8/16 bit DMX512 control for smoother dimming.
•
On board power supply, microprocessor controller, and current drivers.
•
Feed thru DMX/RDM data with a maximum total run of 1000 feet.
•
Push button addressing.
•
Stand-Alone Pre-programmed modes.
•
Keypad Lock functions to prevent accidental Re-Programming.
•
Efficient cooling system offering Silent Operation with No Fans.
WARNING: ALL ELECTRICAL WIRING AND CONNECTIONS SHOULD BE PERFORMED BY A QUALIFIED
ELECTRICIAN
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
4
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
( Firmware Version: V2.3.6)
OPERATION
There are 3 buttons below the 3 digit LED display on the side of the unit. The buttons are : (From left to right)
[ HUNDREDS ] , [ TENS ] , [ ONES ].
All settings for Modes, DMX address, Personalities, etc., can be made by using the three buttons on the back
of the unit while power is on.
(Note: Display goes out after no activity for approx 4 sec. Touch any button once to bring it back on.)
There are 3 main operating Modes: DMX, Fixed Color, and Locked.
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
5
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
DMX Mode:
DMX Mode is used for Setting DMX address, Personalities, and Stand-alone Effects. This is the default mode
for a new unit. (Also see Fixed Color Mode section on page 9.)
To Switch to DMX Mode from Fixed Color Mode (or vice versa ) :
Wait a few seconds until the display goes blank,
• press and hold the [ ONES ] button
• press and hold the [ TENS ] button
• release the [ ONES ] button
• release the [ TENS ] button.
DMX ADDRESS
To set, press the buttons repeatedly (or hold) to count up until the desired DMX address (1-512), appears on
the display. Wait a few seconds, the display will blink once quickly, and the address is set live and retained in
memory, even if you remove power.
(RDM addressing sent from a remote unit will overwrite local DMX setting.)
PERSONALITIES:
There are 8 different personalities.
Each personality is made up of 3 settings: RESOLUTION (8 Bit /16 Bit), MASTER (On /Off ), and SMOOTHING
(On/Off ) which are explained in greater detail below.
The current active Personality # is displayed for about 1 second during power up. The format is Pxx where xx
is replaced by the active personality #01-08.
To set the desired Personality, you must be in DMX mode (not Fixed Color mode).
To select the personality:
• Press the buttons until the desired personality address 601-608) appears in the display (see list below).
• Wait a few seconds, and a confirmation display will appear that shows a question mark? on the left,
followed by the personality #. This gives you an opportunity to either accept or reject the new setting.
• To accept the new personality, press the [ ONES ] button.
• To reject the new personality, press the [HUNDREDS] button (below the ? ).
Once the new personality is accepted, it is entered into memory and retained even if power is disconnected.
Once personality is either accepted or rejected, the display will go back to the current DMX address. The
default personality for a new unit is #02.
EXAMPLE: Let's say that we want to select personality #05. We enter 605 on the display.
After a few seconds the display will show ?05 . Since we want this, we press the [ONES] button
(below the 5 ), and that enters personality #05 into memory.
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
6
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
PERSONALITY ADDRESS SETTINGS LIST
601-608: 4-COLOR CHANNELS:
601
602
603
604
605
606
607
608
Personality #01
8 bit
Uses 4 DMX Channels
Channel order is RGBA
Personality #02
8 bit
Uses 4 DMX Channels
Channel order is RGBA
Personality #03
8 bit
Uses 5 DMX Channels
Channel order is RGBAM
Personality #04
8 bit
Uses 5 DMX Channels
Channels order is RGBAM
Personality #05
16 bit
Uses 8 DMX Channels
Channel order is RrGgBbAa
Personality #06
16 bit
Uses 8 DMX Channels
Channel order is RrGgBbAa
Personality #07
16 bit
Uses 10 DMX Channels
Channel order is RrGgBbAaMm
Personality #08
16 bit
Uses 10 DMX Channels
Channel order is RrGgBbAaMm
Master OFF
Smoothing OFF
Master OFF
Smoothing ON
Master ON
Smoothing OFF
Master ON
Smoothing ON
Master OFF
Smoothing OFF
Master OFF
Smoothing ON
Master ON
Smoothing OFF
Master ON
Smoothing ON
609-612: 1-COLOR CHANNELS
609
Personality #09
8 bit
Smoothing OFF
8 bit
Smoothing ON
16 bit
Smoothing OFF
16 bit
Smoothing ON
Uses 1 DMX Channel
610
Personality #10
Uses 1 DMX Channel
611
Personality #11
Uses 2 DMX Channels
612
Personality #12
Uses 2 DMX Channels
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
7
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
RESOLUTION is selectable as either:
8 Bit (one DMX channel per color) this is normal resolution,
or
16 Bit (two DMX channels per color) Coarse+Fine high resolution similar to moving lights.
If unit is in 8 Bit mode, and the unit is set to DMX Channel 001, then the DMX channels would be:
CH1
CH2
CH3
CH4
Red
Green
Blue
Amber*
If unit is in 16 Bit Mode, and the unit was set to DMX Channel 001, then the DMX channels would be:
CH1
CH3
CH5
CH7
Red Coarse
Green Coarse
Blue Coarse
Amber* Coarse
CH2
CH4
CH6
CH8
Red Fine
Green Fine
Blue Fine
Amber* Fine
Master Channel is selectable as ON or OFF and provides a Master fade channel that dims
all 4 colors proportionally at the same time in order to maintain the color .
If you are in 8 Bit mode and the unit is set to DMX Channel 001, then the DMX channels would be:
CH1
CH2
CH3
CH4
CH5
Red
Green
Blue
Amber*
Master
If you are in 16 Bit mode and the unit is set to DMX Channel 001, then the DMX channels would be:
CH1
CH3
CH5
CH7
CH9
Red Coarse
Green Coarse
Blue Coarse
Amber* Coarse
Master Coarse
CH2
CH4
CH6
CH8
Ch10
Red Fine
Green Fine
Blue Fine
Amber* Fine
Master Fine
SMOOTHING is selectable as ON or OFF and provides a smooth transition ramp from one level to
another in a similar way to how an incandescent lamp behaves. This helps to eliminate the "steppiness"
associated with LED fixtures that is caused by the instantaneous response of LEDs.
*Amber if RGBA, or White if RGBW
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
8
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
STAND-ALONE MODE (does not require a control console):
Note: Must be in DMX Mode (see page 6). If Master Mode (see page 10) is on, stand-alone effects from a
single unit will control other units connected via DMX cable to all synchronize. Set other units to DMX
channel 001.
(Do not use the Stand-Alone Effects while connected to a control console or a conflict may result.)
Color Fades (700-799):
700 - 709
R»A»G»B fade
700 = faster - 709 = slower
740 - 749
B»G»A»R fade
740 = faster - 749 = slower
780 - 789
R»A»G»B»W fade
780 = faster - 789 = slower
790 - 799
W»B»G»A»R fade
790 = faster - 799 = slower
Strobes (800-879):
800 - 809
WHITE STROBE
800 = faster - 809 = slower
810 - 819
RED STROBE
810 = faster - 819 = slower
820 - 829
AMBER STROBE
820 = faster - 829 = slower
830 - 839
GREEN STROBE
830 = faster - 839 = slower
840 - 849
BLUE STROBE
840 = faster - 849 = slower
850 - 858
R-A-G-B RAINBOW STROBE
850 = faster - 859 = slower
870 - 879
B-G-A-R RAINBOW STROBE
870 = faster - 879 = slower
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
9
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
FIXED COLOR MODE:
This is a special mode that allows you to manually select colors for a single unit using the 3 keys. (Also see
DMX Mode on page 6.)
To enter Fixed Color Mode (or exit to DMX Mode) :
Wait a few seconds until the display goes blank,
1. press and hold the [ ONES ] button
2. press and hold the [ TENS ] button
3. release the [ ONES ] button
4. release the [ TENS ] button
While in Fixed Color Mode, the hundreds button cycles through 'r', 'G', 'b', and 'A' colors . The tens and ones
digits select 0-99 values. Level 99 is that channel at full.
Locked Mode:
To Lock (or unlock) the buttons:
Wait a few seconds until the display goes blank,
1. press and hold the [ ONES ] button
2. press and hold the [ HUNDREDS ] button
3. release the [ ONES ] button
4. release the [ HUNDREDS ] button.
Display will show
Loc for a moment and then blink. Buttons will ave no effect until they are unlocked.
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
10
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
MASTER MODE ( Different than the Master Channel described on page 7.)
Master Mode only works while in STAND-ALONE EFFECTS MODE (see page 8). It causes the unit that is
set to Master Mode to behave like a console and Transmit 4-channel (RGBA) 8-bit DMX set on address 001,
reflecting its present light output.
Note: Only the first unit that is going to serve as the MASTER fixture should be set to Stand-alone Effects
mode with Master Mode on. Stand-alone Effects Mode with Master Mode on should also not be used while
units are connected to a DMX console. All fixtures following the Master fixture should be set with the Master
Mode OFF, for Normal Operation.
To Turn on MASTER MODE:
1.
2.
3.
4.
5.
6.
7.
8.
Place fixture in Stand-alone Mode (see page 8)
Wait a few seconds until the display goes blank
Press and hold the [ HUNDREDS ] button
Press and hold the [ ONES ] button
Release the [ HUNDREDS ] button
Release the [ ONES ] button
Display will show ON for a moment to indicate new setting and then blink.
Address remaining fixtures connected to the MASTER fixture to DMX address 001
To Turn off the MASTER MODE:
Wait a few seconds until the display goes blank
Press and hold the [ HUNDREDS ] button
Press and hold the [ ONES ] button
Release the [ HUNDREDS ] button
Release the [ ONES ] button
Display will show OFF for a moment to indicate new setting and then blink.
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
11
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
Spectra Strip Operation
SLAVE
MASTER
MASTER and SLAVE modes refer to the origin of the control signal the fixture is listening to.
SLAVE
• Putting the switch in the “Slave” position means the fixture is listening to the incoming DMX signal.
• Also considered “Normal” operation.
MASTER
• Putting the switch in the Master position means the fixture is NO LONGER listening to the incoming DMX
signal and has now become the source of DMX control information for all fixture coming after it. The
Master fixture will broadcast the pre-built show included in the fixtures software that has been selected
by the user. All fixtures coming after the Master fixture should be set to Slave to receive the DMX signal
originated from the Master fixture. This feature allows for rudimentary color changing capability without
the need of an outside DMX control device.
• Also considered Stand-alone operation.
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
12
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
Menu Navigation
M
-
+
Pressing M
• Shows the current mode or the next menu item; use the M button to browse menus and settings
without making any changes
• Saves a changed value
• Turns off the display at the last menu item
Pressing - or +
• Changes a value (which is only saved when M is pressed).
•
Accidentally changed a value but haven’t confirmed it yet by pressing M ? By refraining from
pressing the buttons for at least 8 seconds, you will leave the ,menu (display is turned off ) without
changing the value.
•
If you are in a menu and want to change to another menu, refrain from pressing the buttons for at least 8
seconds (display is turned off ), and subsequently press the button combination for the menu you want
to change to.
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
13
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
Control Mode Selection
To operate the Spectra Strip, one of two control modes must be selected: DMX Mode or Show Mode (also
known as Stand-alone mode).
MODE SELECTION
DMX Mode:
Set/read the DMX start address of the fixture
Change network resolution to 8 or 16 bit
Select the interpolation mode
Hold M for 5 sec.
SETMODE
+
-
DMX
SHOW
M
Show Mode:
• Selecting one of the 8 pre-programmed shows
• Change the speed of the selected show
• Turn Chase on or off
Note: When the Spectra Strip is in Show Mode, the fixture will not respond
to any incoming DMX signal!
Display off
Preset Selection
Spectra Strip Presets govern the operation of the fixture including how each cell responds, the maximum
intensity the fixture will output and the dimming curve the fixture will operate with.
PRESET SELECTION
M + +
PRESETS
+
-
M
CON1
CON2
CON3
CON4
CON5
CON6
THE1
THE2
THE3
THE4
THE5
THE6
+
-
INTENSITY
Set Intensity:
• Sets the maximum intensity for the fixture.
• Default is 255 or maximum intensity.
0 » 255
M
DIMCURV
+
LIN
LOG
SQUA
M
Select Preset
Select one of the pre-programmed presets: Concert or Theater:
CON1-CON6: Concert Mode.
• Concert mode groups individual LED Cells into groups. CON1 is
all LED cells responding to channels 1-4(RGBA). CON6 is each cell
responding to channels 1-48(RGBA).
THE1-THE6: Theater Mode
• Theater Mode groups cell by traditional border light 3 circuit / 4
circuit emulation.
Display off
Lighting
BRINGING IMAGINATION TO LIGHT
Dimming Curve*:
Selects the output dimming curve. Options are:
• LIN - Linear
• LOG - Logarithmic
• SQUA - Square
Default is LOG
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
14
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
DMX Mode parameter selection
Configuration of the operation of the Spectra Strip while in DMX mode, responding to a DMX control signal.
While in DMX MODE
M
DMX ADDR
+
0 » 512
M
NETWRES
+
8 bit
16 bit
M
INTERPOL
+
OFF
VID
COLR
WHIT
GLOW
M
Display off
Select DMX start address
• This is the start address of the first output of the fixture.
• Total amount of addresses per fixture depends on fixture
configuration and number of cells.
• Default address is 1.
Select network resolution:
• Change between 8 and 16 bit resolution.
• Using 16 bit gives you 2 addresses per output: Address 1 - Coarse,
Address 2 - Fine.
Interpolation modes:
To get the mose optimized dimming performance for different
applications. Default is COLR.
SHOW Mode parameter selection
Configuration of fixture operation while operating as a Stand-alone fixture or Master fixture.
While in SHOW MODE
M
SHOW
+
1»9
M
SPD
-
+
-99 » 99
M
CHAS
M
+
OFF
ON
Display off
Lighting
BRINGING IMAGINATION TO LIGHT
Select Show:
Select one of the pre-programmed shows
• 1 - Static, all outputs 100%
• 2 - Static, R 100%
• 3 - Static, G 100%
• 4 - Static, B 100%
• 5 - Static, A 100%
• 6 - RGB color change
• 7- RGBA color change
• 8 - RGB+A color shift
• 9 - All outputs off
Default is show 1
Set speed:
• Set the show speed between -99 and 99.
• Default is 0
Enable Chase mode:
• Selects the show chasing mode for more dynamic effects.
• Default is OFF
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
15
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
Fixture LOCK
Disabling of the menu while fixture is in operation.
Lock
M + +
Select Lock level:
for 5 sec.
LOCK
+
Soft: Disables menu operation until UNLOCK is applied.
NO
SOFT
HARD
M
Hard: Disables menu operation until FACTORY RESET is applied
NOTE: Only activate the hard lock after careful consideration: once you
have hard-locked the fixture you can ONLY reset the fixture to its factory
default setting.
Display off
Fixture unLOCK
Re-enabling of the menu while fixture is in operation.
Unlock
M + +
Select Lock level:
for 5 sec.
UNLOCK
+
Soft: Disables menu operation until UNLOCK is applied.
YES
NO
M
NOTE: Only activate the hard lock after careful consideration: once you
have hard-locked the fixture you can ONLY reset the fixture to its factory
default setting.
Display off
Fixture test
Individual testing of channels
Test
M + -
Hard: Disables menu operation until FACTORY RESET is applied
Reset to factory defaults
Rests fixture to factory default values
Reset to Factory Default
+ +
TEST
Display off
M + R
G
B
A
RGBA
R
G
B
A
RGBA
1
1
1
1
1
1
1
1
1
1
sec.
sec.
sec.
sec.
sec.
sec.
sec.
sec.
sec.
sec.
+ + for 5 sec.
RESET
PRESMENU
M
Display off
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
16
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
PRESET CONFIGURATIONS FOR FIXTURES
Control configuration for each Preset setting per fixture.
2’ SPECTRA STRIP
Concert 1
Concert 2
A
A
A
A
A
B
A
B
A
A
A
A
A
A
A
A
B
A
A
B
A
B
C
A
B
C
A
B
D
A
B
D
Concert 1
Concert 2
Concert 3
Concert 4
Concert 5
Concert 6
A
A
A
A
A
A
A
A
A
A
A
B
A
A
A
A
B
C
A
A
A
B
B
D
A
A
B
B
C
E
A
A
B
B
C
F
A
B
B
C
D
G
A
B
B
C
D
H
A
B
C
C
E
I
A
B
C
D
E
J
A
B
C
D
F
K
A
B
C
D
F
L
Theater 1
Theater 2
Theater 3
Theater 4
A
A
A
A
B
B
A
A
C
C
B
B
A
D
B
B
B
A
C
C
C
B
C
C
A
C
A
D
B
D
A
D
C
A
B
E
A
B
B
E
B
C
C
F
C
D
C
F
4’ SPECTRA STRIP
Concert 1
Concert 2
Concert 3
6’ SPECTRA STRIP
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
17
Visit our website at www.altmanlighting.com
O P E R AT I O N M a n u a l
Spectra Series
Interpolation Curves
Lighting
BRINGING IMAGINATION TO LIGHT
57 Alexander St., Yonkers, NY 10701
© 2012 Altman Stage Lighting, Inc.
Tel: 914-476-7987
18
Visit our website at www.altmanlighting.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising