P3 International Kill-A-Watt Power Strip Manual

P3 International Kill-A-Watt Power Strip Manual
P4330 Kill A Watt
TM
PS
Operating Manual
Thank you for purchasing the P4330 Kill A Watt™ PS Relocatable Power Tap / Transient
Voltage Surge Suppressor. This operating manual will provide an overview of the product,
safety instructions, a quick guide to operation, and complete instructions for correct usage.
Take the time to completely review these instructions as well as all safety warnings to ensure
your best use of the product.
Now you can protect your valuable electronics and find out what they are actually costing you.
Simply connect these appliances to the Kill A Watt™ PS and it will assess how efficient they
are while the built-in surge protection keeps them safe. Advanced features such as over
current, over voltage, and no load detection provide clean safe power to your expensive
equipment. Check the quality of your power by monitoring Voltage, Amperage, KWH, Current
Leakage and more. Now you’ll know how much power your entire computer of home theater
system is using. With the innovative Kill A Watt™ PS you’ll have peace of mind in more ways
than one.
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
Safety Instructions
Read Instructions – All the safety and operating instructions should be read before the product is operated.
Retain Instructions – The safety and operating instructions should be retained for future reference.
Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.
Follow Instructions – All operating and use instructions should be followed.
Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners.
Attachments – Do not use attachments not recommended by the product manufacturer as they may cause
hazards.
Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub; in a wet basement; or near a swimming pool and the like.
Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult and serious damage to the product. Any mounting of the product should
follow the manufacturer’s instructions.
Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these openings (if any) must not be blocked or covered. The
openings (if any) should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been adhered to.
Power Sources – This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your home, consult your product dealer or local power
company. For products intended to operate from battery power, or other sources, refer to the operating
instructions.
Grounding or Polarization – This product may be equipped with a polarized alternating-current line plug (a plug
having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
Lightning – For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to
lightning and power-line surges.
Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
Object and Liquid Entry – Never push objects of any kind into this product through openings (if any) as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of
any kind on the product.
Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified technician to restore the product to
its normal operation.
If the product has been dropped or damaged in any way.
When the product exhibits a distinct change in performance – this indicates a need for service.
Replacement Parts – When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine that the product is in proper operating condition.
Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products that produce heat.
Safety Instructions:
1. The operating voltage is limited. Maximum operating voltage is 120Vac. Do not use the unit with other
operating voltages.
2. The maximum output current is 15A.
3. To reduce the risk of electric shock, do not remove cover. No user-serviceable parts inside. Refer
servicing to qualified service personnel.
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
Product Functions:
1.
2.
3.
4.
5.
Power Strip: 10 outlets, Spike-free switch.
Multi-Meters: Voltage, Current, Active Power, Power Factor, KWH, Leakage Current, Elapsed Time.
Protection: Abnormal Voltage, Over Current, Over Load, Surge.
Programmable Breaker Current: User adjustable 2, 5, 10, or 15A breaker.
NFB (No Fuse Breaker): Over Load protection.
Wall Mount Instructions (Optional)
1.
2.
Use 3/4 inch no. 8 screws or similar.
Space the 2 screws about 9 inches (285mm) apart according to the figure. Leave about 1/4 inch (5mm)
of the screw head protruding from the surface.
3. Place the unit against the surface with the screw heads fitting into the mounting holes.
4. Move the unit downwards to secure the mounting holes onto the screw heads.
Mounting Hole
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
Feature Locations
10 Normal Outlets
NFB Short Breaker
ON
Elapsed Time
KWH/Leakage
OFF
Watt/PF
Max.Amps
Volt/Amp
Display Panel
AC Voltage
AC Power
Kilo - Watt - Hour
Up to date Max.
No Appliance connected
Over 15A Max Current
Defect Detect
Out of Range Voltage
Elapsed Days
Over
Current
Over current
NO Load
Over Load
MAX
REPLACE
Abnormal
Voltage
MIN
Surge
OK
Ground
OK
Volt
Watt
KWH
Day
Amp
mA
%
Wiring
OK
AC Current
Leakage Current
Hour
Up to date Min.
Elapsed Hours
Power Factor
Surge Protection Ready
Grounded Correct
Line、Neutral Wired Correct
Quick Start Guide:
Use these quick start instructions to get up and running in just a few minutes. Be sure to review all the operating
instructions later to ensure full enjoyment of the product.
1.
2.
3.
4.
5.
Connect the Kill A Watt™ PS unit to the outlet and the appliance to the unit.
The LCD display will flash. Press any of the function keys to stop the flashing.
Press the OFF key. The OFF key will illuminate red.
Press the ON key. The ON key will illuminate green and the attached appliance will be powered.
If the attached appliance is turned off and is not consuming any power, the unit will detect no load. The
ON key will go dark and the “NO Load” icon will flash on the LCD display. THIS IS NORMAL. If the
attached appliance is then turned on, the unit will detect a load, the ON key will illuminate and the “NO
Load” indicator on the LCD display will disappear.
6. Pressing the Volt/Amp key will cycle through currently measured voltage (Volts), current (Amps) and
Maximum/Minimum measured values.
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
7.
Pressing the Watt/PF Key will cycle through currently measured active power (Watts), power factor (%)
and Maximum/Minimum measured values.
8. Pressing the KWH/Leakage key will cycle through cumulative kilowatt hours (KWH), currently measured
leakage current (mA) and Maximum/Minimum measured values (leakage current only).
9. Pressing the Elapsed Time key will cycle through time in Days:Hours and Hours:Minutes.
10. Review the complete operating instructions to familiarize yourself with all features.
Installation:
Remove the protective film (if any) covering the LCD meter display by pulling the tab marked “REMOVE
BEFORE USE”.
2. Turn off all appliances before connection to the unit and remove their power cords from the outlet.
Connect the Kill A Watt™ PS unit to the outlet and the appliances to the unit.
3. The LCD display will be flashing. This is normal when the unit is first connected to power and when
power is restored after an interruption. Press any of the function keys to stop the LCD from flashing.
4. If you want to reset KWH and time measurements, hold the Elapsed Time key down for 3 seconds.
Previous measurements will be deleted and the total accumulated KWH and Elapsed Time
measurements will be reset to zero
1.
ON/OFF Key Function
1.
Pressing the OFF key will turn off power to the 10 outlets at once. The OFF key will illuminate in red.
The unit will continue to measure power (e.g. Voltage, Time) and the function keys and LCD display will
continue to operate.
2. Pressing the ON key will turn power on to the 10 built-in outlets at once. The unit features a spike-free
switch function which activates at zero-crossing and will present clean power to your connected
appliances. The ON key will illuminate in green. The unit will measure power and the function keys and
LCD display will operate.
3. While the unit is turned ON, if all loads to the unit are removed then the No Load function will detect this
condition and automatically turn off power to the 10 built-in outlets. Both the ON and OFF keys will be
dark and a “NO Load” indicator will flash on the display. THIS IS NORMAL and is a safety feature. When
the electrical load is reapplied, the unit will automatically turn ON, illuminate the ON key and energize
the 10 built-in outlets. While in the No Load mode, you can turn the unit off by pressing the OFF key.
The OFF key will illuminate in red and power will not be applied to the outlets.
Understanding the No Load Function
1.
No Load means no electrical load placed on the unit. Either there are no appliances connected to the
unit or the appliances connected are turned off and are not drawing any stand-by power. If a connected
appliance is turned off but is still drawing stand-by power, there is still a load placed on the unit. The unit
will not enter the No Load mode.
2. The No Load function provides safety by removing electrical power from all connected cords and
appliances when they are turned off. This is important because normally, even when an appliance is
turned off, the electrical cord and part of the appliance are still energized by electricity. If the cord or
appliance is cut, opened or frayed, electrical shock or damage can occur. When the unit is in No Load
mode, these cords are not energized which prevents these problems. It is still important that all
damaged equipment and cords are repaired or replaced immediately. The No Load function is not a
replacement for proper maintenance.
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
Retained Output Mode:
1.
If the power supply to the Kill A Watt PS unit is interrupted and then restored, the LCD panel will flash to
alert the user to an interruption. Press any of the function keys to stop the LCD from flashing. The unit
will resume the output mode at time of power interruption. If the unit was ON, when power was removed,
the unit will be ON when power is restored.
Meter Functions:
1.
Volt/Amp key: Pressing the Volt/Amp key repeatedly will cycle through displaying the currently
measured AC line voltage (in Volts) with the currently measured load current (in Amps), the maximum
measured voltage/current (indicated by the MAX icon) and the minimum measured voltage/current
(indicated by the MIN icon). The display will return to the currently measured values after a few seconds.
Pressing and holding the Volt/Amp key for a few seconds will delete the memorized MAX/MIN values.
The measured load current is the sum of all connected appliances.
2. Watt/PF key: Pressing the Watt/PF key repeatedly will cycle through displaying the currently measured
appliance power consumption (in Watts) with the currently measured power factor (in %), the maximum
measured watts/PF (indicated by the MAX icon) and the minimum measured watts/PF (indicated by the
MIN icon). The display will return to the currently measured values after a few seconds. Pressing and
holding the Watt/PF key for a few seconds will delete the memorized MAX/MIN values. The measured
power consumption is the sum of all connected appliances.
3. KWH/Leakage key: Pressing the KWH/Leakage key repeatedly will cycle through displaying the
cumulative appliance power consumption (in Kilowatt Hours) since last reset with the currently
measured leakage current (in milliamps), the maximum measured leakage current (indicated by the
MAX icon) and the minimum measured leakage current (indicated by the MIN icon). The display will
return to the currently measured values after a few seconds. Pressing and holding the KWH/Leakage
key for a few seconds will delete the memorized MAX/MIN values for leakage current. There are no
MAX/MIN values for KWH as it is a cumulative value. IF YOU NOTE SIGNIFICANT LEAKAGE
CURRENT MEASUREMENTS STOP USING THE CONNECTED APPLIANCE(S) IMMEDIATELY
AND HAVE IT SERVICED
4. Elapsed Time key: Pressing the Elapsed time key repeatedly will cycle through displaying the elapsed
time of energy usage in Days:Hours and Hours:Minutes. Pressing and holding the Elapsed Time key for
a few seconds will reset the elapsed time counter to zero and will clear cumulative KWH measurement.
Be sure you have taken note of KWH measurements (if desired) before you reset as they cannot be
retrieved once reset.
Retained Measurements:
1.
When power to the Kill A Watt™ PS is interrupted, the display will go blank and the unit will stop
measuring consumption and elapsed time. However all accumulated measurements including KWH and
Elapsed Time will be retained.
2. This allows the user to take measurements anywhere and relocate the unit to a more convenient
location to read the display. When the unit is plugged back in, the display will become active and will
flash as an indicator of power interruption. Press any key momentarily to cancel the flashing. The
accumulated KWH measurement can be retrieved by using the KWH/Leakge key. The accumulated
elapsed time can be retrieved by using the Elapsed Time key. Data should be retrieved immediately as
the Elapsed Time counter will restart and potentially skew the data as time with no load elapses.
3. Pressing and holding the Elapsed Time key for a few seconds will reset the elapsed time counter to zero
and will clear cumulative KWH measurement. Be sure you have taken note of KWH measurements (if
desired) before you reset as they cannot be retrieved once reset.
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
Protection Functions:
1.
Max. Amps switch: This switch on the control panel allows the user to optionally select the maximum
current (Amps) the unit will deliver to the attached appliances without automatically shutting off. Use a
small screwdriver to select 2A, 5A, 10A or 15A (factory default).
Setting Procedure:
a. Use a small screwdriver to select 15A (factory default setting).
b. Connect all appliances to the unit and operate appliances at their highest level.
c.
Press the Volt/Amp key to observe the current value (Amps) consumed by appliances.
d. Turn off the connected appliances and turn the unit off.
e. Use the small screwdriver to set Max. Amps to the next highest value. For example if the LCD
display indicates your appliances are consuming 6.12 Amps at their highest level, set the Max.
Amps switch to 10A. In the future, if the attached appliances begin to draw a higher than normal
load and exceed 10A of current, the unit will go into Over Current Mode (see below), shut off power
and help protect the connected appliances.
f.
Resume normal operation.
2.
NFB (No Fuse Breaker) The NFB will activate when the unit is subject to overload. Press the NFB to
reset and restart.
3. Over Current mode: When the current load presented by the connected appliances exceeds the
setting on the Max. Amps switch, the unit will switch to Over Current mode. The power will be switched
off to the 10 outlets. The red LED in the OFF switch will flash. The LCD will display the protected current
value. The Over Current icon will flash and the audible alarm will sound. Remove the appliance(s) which
is causing the over current power draw or readjust the Max. Amps value to a higher setting. Then press
the OFF key and then the ON key to turn the power back on.
4. Abnormal Voltage mode: When the voltage presented at the wall outlet if over or under the normal
voltage range, the unit will switch to Abnormal Voltage mode. The power will be switched off to the 10
outlets. The red LED in the OFF switch will flash. The LCD will display the protected voltage value. The
Abnormal Voltage icon will flash and the audible alarm will sound. When the AC line voltage delivered
by the wall outlet returns to a normal range and is stable for at least 3 seconds, the unit will switch back
to normal mode and restart power immediately. The unit will enter Abnormal Voltage mode if the AC line
voltage is over normal by 13% or under normal by 18%. The unit will switch back to normal mode when
the AC line voltage returns to +10% to -15% normal.
5. Over Load mode: The unit contains dual redundant over load protection circuits; an electronic control
breaker and a traditional NFB (No Fuse breaker).
a. Electronic control breaker: When the current load presented by the connected appliances exceeds
15 Amps, the unit will switch to Over Load mode. The power will be switched off to the 10 outlets.
The red LED in the OFF switch will flash. The Over Load icon will flash and the audible alarm will
sound. Remove the appliance(s) which is causing the over load power draw. Then press the OFF
key and then the ON key to turn the power back on.
b. NFB (No Fuse breaker): When the NFB detects an over load condition, it will set and cut off power
to the unit. This will cut off power to the 10 outlets as well as the LED’s and LCD display panel. The
unit will be totally without power. Check and remove the appliance(s) causing the over load, and
then press the NFB button to reset the breaker.
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
6.
Ground OK, Wiring OK detection: When you connect the unit to a wall outlet, the unit will check the
structure wiring to determine and wire faults. The unit checks the Line, Neutral and Ground wiring.
Under normal conditions, “Ground OK” and “Wire OK” icons will display on the LCD. If Line or Neutral
are in the wrong positions, the “Wire OK” icon will disappear. If the Ground wiring is not correct, both
“Ground OK” and “Wire OK” icons will disappear.
7. Surge Protection: The unit features a self-test function. If the surge protection circuitry is operating
properly, the LCD display with indicate with the “Surge OK” icon. If the surge protection has failed, the
“Surge OK” icon will disappear.
8. EMI Filter: The unit features a built-in EMI (electro-magnetic interference) filter to reject noise from the
AC power line.
9. Internal Switch Self Test: The LCD will flash the “REPLACE” icon and sound an audible alarm if the
unit detects that the internal relay switch has failed.
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
Troubleshooting:
Item
Symptoms
Action
Description
1
LCD display is flashing
Press any key
2
Over Current icon on LCD
is flashing and audible
alarm is sounded, output is
off and the red LED in the
OFF key is flashing
Press Reset key (OFF key), check &
remove the appliance which is drawing
over current or reduce the number of
appliances connecting to the unit or set
a larger Max. Amps setting. Press ON
key to restart
1. This is normal operation after
you plug the unit into a wall outlet.
2. AC power to the unit has been
interrupted.
This is the over current protection
function indicating the total power
consumption is larger than the
Max. amps setting value or that an
appliance is drawing too much
current.
3
Over Load icon on LCD is
flashing and audible alarm
is sounded, output is off
and the red LED in the
OFF key is flashing
Press Reset key (OFF key), check &
remove the appliance which is drawing
an over load of current. Press ON key
to restart.
This is the over load protection
function. Indicates that attached
appliances could have a short
circuit.
4
Abnormal Voltage icon on
LCD is flashing and
audible alarm is sounded,
output is off and the red
LED in the OFF key is
flashing
The unit will restart automatically when
the AC power line voltage returns to
normal voltage range. If condition
persists call a qualified technician.
This is the abnormal voltage (too
high or too low) protection
function.
5
No Load icon on the LCD
display flashes
The unit will power on automatically
when the load returns
This is the no load protection
function to reduce the chance
electrical shock or damage
6
No Load icon continues to
flash when appliances are
connected and turned on
Increase the number of connected
appliances
The minimum watt detected by the
unit is 0.2W. Some few appliances
may have a stand-by mode that
consume less than 0.2W.
7
Replace icon on the LCD
flashes
Request technical support
This is a self diagnostic function
for the main power relay switch.
This indicates the relay is non
functional.
8
Ground OK & Wiring OK
icon on the LCD are turned
off
Ask for a qualified electrical technician
to check your house wiring and
grounding
These icons turning off indicate a
wiring defect
9
Surge OK icon on the LCD
is turned off
Request technical support
This is a self diagnostic function
for the surge protector MOV
indicating the MOV is non
functional
10
No display in the LCD, no
response from pressing
keys
1. Check that the unit connected to an
energized AC wall outlet.
2. Check if the NFB (No Fuse breaker)
is ejected from the body of the unit.
If yes, disconnect any defective
appliances from the unit, then press
the NFB button again to restart.
a. 3. Request technical support
When no AC power is applied or if
the NFB is ejected the unit will not
function.
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
Specifications:
ITEM
ACCURACY
Typ.
Max.
RANGE
RMS voltage
RMS current
108.0~132.0 Vrms
0.0~15.0Arms
0.1%
0.5%
Active power
0.0~1980 Watt
1%
KWH1
Power Factor
Leakage Current
1
Elapsed Time
Abnormal
Voltage
Under Voltage
Protection
0.0~9999 KWH
0~100%
0~30mA
00Day/00Hour~9999Day/23Hour
00Hour/00Min~23Hour/59Min
Output Off if Vac<98.4V (Rating-18%)
Then On if Vac>102V(Rating-15%)
Over Voltage
Protection
Output Off if Vac>135.6V(Rating+13%)
Then On if Vac<132V(Rating+10%)
Over Current Breaker
Programmable
2A,5A,10A,15A
Electronic
Short
Breaker
Active Current
No Load Detector
Surge Protection
EMI Filter
1
0.4%
1%±0.1A
1sec
1sec
2%± 5w
1sec
1%
2%± 5w
PF=W/Vrms*Arms
±1mA
Off:<0.2W : On:>0.2W
Maximum energy
Dissipation (Joules)
(L-N,L-G&N-G)
Maximum Clamping Voltage
Maximum Surge Current
Up to 20db for 100K to 20MHz
1sec
1sec
1sec
1Hour
1Min
30ppm
0.1%
0.4%
0.1%
0.4%
0.5%
1%±0.1A
Ipk>150A
NFB
RESPONSE TIME
Action
Recovery
1sec
3sec (Auto)
2sec
Manual
<0.1sec
LoadAmp=100%(15A)
LoadAmp=150%(22.5A)
LoadAmp=200%(30A)
LoadAmp=400%(60A)
LoadAmp=600%(90A)
±0.1W
--1Hour
Manual
4~40sec
0.42~5sec
0.1~1.8sec
3sec
3sec
<50ns
N/A
2040 J
359 V
60000A
Display will flash when maximum count is reached for KWH, Elapsed Time
Technical Specification
Indoor use only
Altitude up to 2000m
Temperature 5℃to 40℃
Maximum relative humidity 80% for temperature up to 31℃decreasing linearly to 50% relative humidity at 40℃
Mains supply voltage fluctuations not to exceed ±10% of the nominal voltage
Pollution Degree 2
Installation category II
Specification
Voltage rating:
Power consumption:
Power cord:
W/H/D
Weight
Shop for P3 products online at:
www.
120Vrms ± 10% , 60Hz
1.0W
1.8m
320mm x 53mm x 78mm
450 g (without power cord)
PowerMeterStore.ca
1.877.766.5412
P3 INTERNATIONAL CORPORATION
LIMITED WARRANTY
P3 INTERNATIONAL CORPORATION ("P3") warrants to the original retail purchaser only, that its product is free from defects in material or
workmanship under the condition of normal use and service for a period of six (6) months from the date of purchase. In the event that a
defect, malfunction or failure occurs or is discovered during the warranty period, P3 will repair or replace at its option the product or
component part(s) which shall appear in the reasonable judgment of P3 to be defective or not to factory specifications. A product requiring
service is to be returned to P3 along with the sales receipt or other proof of purchase acceptable to P3 and a statement describing the defect
or malfunction. All transportation costs shall be borne by the owner and the risk of loss shall be upon the party initiating the transportation. All
items repaired or replaced thereunder shall be subjected to the same limited warranty for a period of six (6) months from the day P3 ships the
repaired or replaced product. The warranty does not apply to any product that has been subject to misuse, tampering, neglect, or accident or
as a result of unauthorized alterations or repairs to the product. This warranty is void if the serial number (if any) has been removed, altered,
or defaced. This warranty is in lieu of all warranties expressed or implied, including the implied warranties of merchantability and fitness for a
particular purpose which are expressly excluded or disclaimed. P3 shall not be responsible for consequential, incidental or other damages,
and P3 expressly excludes and disclaims liability for any damages resulting from the use, operation, improper application, malfunction or
defeat of any P3 product covered by this limited warranty. P3's obligation is strictly and exclusively limited to the replacement or repair of any
defective product or component part(s). Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. P3 does not assume or authorize anyone to assume for it any other obligation
whatsoever. Some states do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you. It is
the owner/user's responsibility to comply with local, state, or federal regulations, if any, that may pertain to P3 products or their use. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
If you experience difficulty in the operation of your unit, or if your unit requires repair please contact:
P3 INTERNATIONAL CORPORATION
TECHNICAL SUPPORT
Tel: 212-741-7289
Fax: 212-741-2288
Email: techsupport@p3international.com
Rev. 0110
Shop for P3 products online at:
www.
PowerMeterStore.ca
1.877.766.5412
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising