eBridge1PCTX IP and PoE/PoE+ over Coax Hardened

eBridge1PCTX IP and PoE/PoE+ over Coax Hardened
Installation Guide
Rev. 111814
PLUS
eBridge1PCTX
IP and PoE/PoE+ over Coax
Hardened Transceiver
Z1409
I.T.E. 43KC
Overview:
The eBridge1PCTX is a CAT5 to Coax cable Ethernet adapter that delivers data and power over
the coax cable in a PoE compliant format. The transceiver enables fast 10/100Base-T Ethernet
digital communication to be transmitted over Coax cable. An eBridge1PCRX, eBridge4PCRX,
eBridge8PCRX or eBridge16PCRX receiver sends power over the coax to the eBridge1PCTX
transmitter under PoE protocol. The eBridge1PCTX in turn delivers that PoE compliant power
to a PoE enabled camera or IP device. These plug and play units facilitate system upgrades from
analog to IP cameras/devices utilizing existing legacy Coax and eliminating the costs and labor
associated with installing new network cabling. In addition, data transmission and power over the
Coax is possible up to 457m in comparison to 100m Ethernet maximum distance (see Maximum
Length of Coax Type vs. Camera Power/PoE Class, pg. 3). A maximum range from headend to
the PoE camera/device is 610m, taking into consideration that up to 100m of structured cable may
be deployed at each end.
Agency Listings:
•
•
•
UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
CE approved.
C-Tick compliant.
Features:
LED Indicators:
Power Consumption (under maximum load):
• eBridge1PCTX: Powered by
eBridge1PCRX, eBridge4PCRX,
eBridge8PCRX or eBridge16PCRX receiver.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5e or better
structured cable.
• Distance: up to 100m.
•Speed: 10/100BaseT, half/full duplex,
auto negotiation. PoE compliant to
IEEE 802.3af (15W) Delivered to
camera by eBridge1PCTX. Power provided
by eBridge Plus receiver to eBridge1PCTX
by PoE protocol.
Coax:
•
•
•
Distance: up to 457m (see Maximum Length
of Coax Type vs. Camera Power/PoE
Class, pg. 4) for power delivery of coax.
Throughput is rated to pass 25mbps of data
at distances up to 457m. With proper
headend equipment this supports
Megapixel, HD720, HD1080.
Connectivity: BNC, RG-59/U or similar.
eBridge1PCTX
• Blue LED - Coax link connection.
Green LED - PoE from eBridge1PCRX.
Environmental:
•
•
•
Operating Temperature:
For 15W: --- 40ºC to 75ºC (--- 40ºF to 167ºF).
For 30W: --- 40ºC to 49ºC (--- 40ºF to 120.2ºF).
Storage Temperature:
--- 40ºC to 75ºC (--- 40ºF to 167ºF).
Humidity: 20 to 85%, non-condensing
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
•
•
•
•
Retrofit digital IP cameras in an analog
CCTV installation.
Works with Megapixel, HD720, HD1080
and VGA (SD) cameras (see note, pg. 2).
Extend Network link distance in an
industrial environment over 610m
(see note, pg. 2).
Upgrade deployed CCTV Coax to a digital
network in Retail, Hospitality, Arenas,
Casinos, Airports, Schools,
Hospitals, Transportation, etc.
Mechanical:
• Dimensions (W x L x H approx.):
2.5” x 4.375” x 1”
(63.5mm x 111.125mm x 25.4mm)
-1-
­­­Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and
with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or
Recognized wire suitable for the application.
eBridge1PCTX is not intended to be connected to outside plant leads and should be installed
indoors within the protected premises. eBridge1PCTX is intended for indoor use only.
1. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s
mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity of camera/device.
2. Connect structured cable from IP camera/device to RJ45 jack marked [10/100BaseT]
(Fig. 2, pg. 3).
3. Connect Coax from eBridge receiver (eBridge1PCRX, eBridge4PCRX, eBridge8PCRX or
eBridge16PCRX) to BNC connector marked [Coax] (Fig. 2 & 3, pg. 3).
Note: The eBridge1PCTX is designed to accommodate Megapixel, HD720, HD1080 and VGA
(SD) cameras. It is important to note that some high resolution and high frame rate cameras may
demand faster headend processing ability, such as a PC graphics card to present a quality image.
If the headend processing equipment is insufficient in speed, the image may show pixelation and
latency. It is advisable to pre-test system if unsure. Alternatively, frame rate and resolution may
be reduced to accommodate system equipment.
Technical Specifications:
Parameter
Connections
Input power requirements
Indicators
Description
BNC for Coax link. RJ45 for ethernet link.
24VDC/1,000mA, 24VAC/900mA
Blue: Coax Link.
Yellow (RJ45 connector): On - Link,
Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX,
Off - 10Base-T.
Green: Power.
Operating Ambient Temperature: UL60950-1
For 15W: --- 40ºC to 75ºC (--- 40ºF to 167ºF).
For 30W: --- 40ºC to 49ºC (--- 40ºF to 120.2ºF).
Environmental Conditions
Relative humidity: 85%, +/ --- 5%
Storage Temperature: --- 40ºC to 75ºC (-- 40ºF to 167ºF).
Operating Altitude: --- 1000 to 6,561.679 ft. (--- 304.8 to 2000m).
Regulatory Compliance
Weights (approx.)
Fig. 1
UL/CUL Listed for Information Technology
Equipment (UL 60950-1).
Product: 0.25 lbs. (0.11 kg), Shipping: 0.6 lbs. (0.27 kg).
eBridge1PCTX
Green LED
indicates
Power
CAT5e or higher cable
from IP Camera/Device
Coax Cable from
eBridge1PCRX,
eBridge4PCRX, eBridge8PCRX
or eBridge16PCRX
eBridge1PCTX
Blue LED
indicates
Coax Connection
-2-
Single PoE Camera Connection:
Fig. 2
eBridge1PCRX
eBridge1PCTX - Transceiver
Provides PoE/PoE+
Provides PoE/PoE+
Blue LED Coax link status
RJ45 LEDs Yellow - Speed
Green - Activity
Green LED Power
Input: 24VDC/1500mA, 56VAC/900mA (under maximum load)
Blue LED Coax link status
RJ45 LEDs Yellow - Speed, Green - Activity
Green LED Power and PoE
Z1409
Z1409
Coax
SLOC
Link LED
Power
LED
www.altronix.com
10/100
Base-T
--- +
Power
LED
Power
Input
PoE LED
Coax
SLOC
Link LED
www.altronix.com
PoE compliant
100m max.
24VDC to
56VDC
Input
100m
max.
PoC (PoE+ over Coax)
457m max.
Ethernet Switch
Legend:
Coax
Structured Cable
Multiple PoE camera connection:
Fig. 3
eBridge1PCTX
PoE Camera
I.T.E. 43KC
I.T.E. 43KC
10/100
Base-T
Mounting Hole
eBridge1PCTX
eBridge1PCRX - Receiver
NVR Network
Video Server
(Head End
Equipment)
Fig. 2a
eBridge1PCTX
IP Camera
Up to
457m
eBridge1PCTX
eBridge1PCTX
IP Camera
Up to
457m
IP Camera
Up to
457m
IP Camera
Up to
457m
Ethernet
10/100
Base-T
1
2
Up to
100m
3
4
Up to
100m
10/100
Base-T
5
6
7
8
eBridge8PCRX (Front)
Ethernet Switch
eBridge1PCTX
-3-
Maximum Length of Coax Type vs. Camera Power/PoE Class:
Cable Type
RG59u/23awg
RG59u/23awg
RG59U/22awg
RG59U/22awg
RG59U/20awg
RG59U/20awg
RG59U/18awg
RG59U/18awg
Total Power
Consumption
15W
30W
15W
30W
15W
30W
15W
30W
Max Data
Distance
500m
500m
500m
500m
500m
500m
500m
500m
Max Power
Distance
264m
132m
334m
167m
532m
266m
846m
423m
Notes:
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
website: www.altronix.com, e-mail: info@altronix.com. Lifetime Warranty, Made in U.S.A.
IIeBridge1PCTXI12P
eBridge1PCTX
MEMBER
-4-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising