vacuum cleaning attachments and accessories

vacuum cleaning attachments and accessories
BULLETIN 241R.2
VACUUM CLEANING
ATTACHMENTS AND
ACCESSORIES
ASSEMBLY INSTRUCTIONS
Male Coupling to Inlet Valve
Inlet Valve
Valve Cover
Hook Device
Male Coupling
Male Hose Coupling to
Female Coupling
Locking Ring
Groove
Locking Band or Ring
Ridge
Grooved Neck to Knurled Nut Connector
Knurled Locking Nut. Turn to
Tighten Lock Ring.
Neck With
Groove For
Lock Ring
Knurled Locking Nut Tightened
Lock Ring
Ring in Groove
Tightened and Locked
Typical Floor Tool and
Elbow Joint Assembly
Elbow Joint
Knurled Nut
Female Coupling
Hose
Male Coupling
Handle
Knurled Nut
Tool
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
www.spencerturbine.com
TOOLS
Vacuum tools with brushes or bristles are used when it
is necessary to dislodge material before it is picked up.
Three types of brush material are used by Spencer.
Spencer tools are made of durable materials and are
designed for convenience and effectiveness with
openings in correct proportion to the rest of the system.
All wearing surfaces are renewable.
HORSEHAIR
Soft – Cut from the mane or tail. A gentle brush
best suited for smooth surfaces or walls.
Floor tools are available in three basic sizes.
12" Wide
For cleaning congested areas, around chairs, or in
narrow areas where a large tool would be awkward
to use.
NYLON BRISTLES
Medium Stiffness – A popular brush material, man
made synthetic fiber recommended for general
service, long life, chemical resistant, good memory.
14-15" Wide
The most practical and common for general service.
TAMPICO FIBERS
Stiff – A common high quality fiber bristle derived
from plants. Use for heavy brush service, fair
memory, heat resistant.
20" Wide
Designed for use in large unobstructed areas such
as corridors, auditoriums, or gymnasiums.
Brush material is designated in item description.
Note: Part numbers are listed first. The old catalog
number is listed in parentheses.
Note: Replacement parts available for most tools.
Replacement part numbers are listed in blue italic.
11/2" BARE FLOOR TOOLS
Bare Floor Tools are designed for use at the end of a wand.
BRUSH STRIPS – Nylon for
sticky dust or rough uneven
surfaces.
*Replacement strip
FELT BLADES – For polished
floors, wood, linoleum, and
other smooth surfaces.
*Replacement strip
RUBBERIZED FABRIC – For
unfinished wood floors and
rough surfaces. Also liquid
removal from rough surfaces.
*Replacement strip
*Quantity (2) required.
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
12" Wide
15" Wide
20" Wide
VTL90019
(1210)
.88 lb.
BRS90003
VTL90018
(1510)
1 lb.
BRS90004
VTL90020
(2010)
1.50 lb.
SVT90027
VTL90021
(1211)
.94 lb.
SVT90005
VTL90022
(1511)
1.13 lb.
SVT90006
VTL90023
(2011)
1.63 lb.
SVT90007
VTL90024
(1212)
1.44 lb.
VTL90025
(1512)
1.75 lb.
VTL90026
(2012)
2.2 lb.
SVT90002
◆
TEL 860.688.8361
◆
SVT90003
FAX 860.688.0098
◆
SVT90004
www.spencerturbine.com
1
11/2" BARE FLOOR TOOLS
Bare floor tools are designed for use at the end of a wand.
Replacement part numbers are listed in blue italic.
*Quantity (2) required.
SQUEEGEE – Pliable rubber
blade for liquid recovery.
Replacement blade black
Replacement blade white
Replacement bumper
STEEL BLADES – For
scraping or severe service
on rough abrasive floors as
in industrial plants.
*Replacement blade
12" Wide
15" Wide
VTL90027
(1213)
2.19 lb.
BLV90000
BLV90002
BUF90004
VTL90028
(1513)
2.63 lb.
BLV90001
BLV90003
BUF90002
VTL90029
(1214)
1.56 lb.
VTL90030
(1514)
1.88 lb.
VTL90033
(1215)
.88 lb.
SVT90000
VTL90032
(1515)
1.00 lb.
SVT90001
VTL90036
(1216)
1.88 lb.
VTL90035
(1516)
2.25 lb.
SVT90008
PLASTIC BLADES – For
clean room and food
handling applications.
*Replacement blade
ELEVATED BLADES WITH
WHEELS – For severe service
and mobility on rough
industrial plant floors.
*Replacement wheel
20" Wide
SVT90009
WHL90006
WHL90006
CEMENT FLOOR TOOL –
Tampico bristles for loosening
—
sticky materials on rough
surfaces or unfinished
cement floors.
Replacement brush (polypropylene base)
—
VTL90031
(2014)
2.44 lb.
SVT90010
—
VTL90037
(2016)
2.88 lb.
WHL90006
VTL90017
(1290)
1.5 lb.
BRS90030
4" GULPER WITH WAND –
VTL90047
(1786)
4.13 lb.
Aluminum. For removing
large accumulations of litter,
complete with permanently
attached wand. Connects
directly into 11/2" female
hose coupling, elbow joint
or hose connector.
2
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
www.spencerturbine.com
11/2" HAND TOOLS
Hand tools attach directly to the female hose coupling.
*May also be used with wall handles, hose connectors, or gooseneck.
Replacement part numbers are listed in blue italic.
8" HAND BRUSH – Nylon. Designed for hand cleaning
of large flat surfaces like shelves and ledges.
Replacement brush
Replacement bumper
4" ROUND BRUSH – Nylon with polypropylene base.
Recommended for general cleaning.
VTL90040*
(1270)
1.50 lb.
BRS90029
BUF90000
Replacement brush/base
Replacement bumper
4" ROUND BRUSH – Nylon with hose swivel and
polypropylene base. Recommended for general cleaning.
Replacement brush/base
Replacement bumper
VTL90042
(1811)
1.25 lb.
BRS90029
BUF90000
CORNER & CREVICE – Anodized Aluminum.
Designed for difficult to reach areas.
Recommended for heavy duty surface.
VTL90002
(1471)
.63 lb.
CORNER & CREVICE – Zinc Plated Steel.
Designed for difficult to reach areas.
Recommended for severe duty surface.
VTL90001
(1472)
.88 lb.
6" HAND TOOL – For cleaning shelves,
ledges or upholstered furniture.
VTL90052*
(2975)
1.13 lb.
6" HAND TOOL – With nylon brush for removing
sticky dirt.
VTL90053*
(2976)
1.25 lb.
BRS90010
Replacement brush
4" GULPER – Aluminum. For removing large
accumulations of bulky litter.
The Spencer Turbine Company
◆
VTL90039
(920)
1.13 lb.
BRS90007
BUF90001
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
BOV90010
(1785)
1.75 lb.
◆
www.spencerturbine.com
3
11/2" HAND TOOLS
Hand tools attach directly to the female hose coupling.
GULPER – Rubber. For easy cleaning around
machinery. Full bore for large accumulation
of material pickup.
VTL90050
(2002)
.88 lb.
SUMP TANK – Steel. Liquid-handling—has
3/8 inch bleeder hole to speed pick-up.
Recommended for use with Spencer Sump-Vac®.
VTL90054
(2510)
2.13 lb.
TAPERED NOZZLE – Rubber. Oil resistant.
Designed for cleaning holes or for use around
motors or other electrical equipment.
Also used for blowing applications.
VTL90051
(2515)
.44 lb.
11/2" CARPET TOOLS
Carpet tools are used at the end of a wand.
Replacement part numbers are listed in blue italic.
NARROW SLOT – With rubber bumper
and plain metal shoe. Most effective for
deep cleaning—short or medium pile.
Also effective for drawing excessive
water from carpet.
Replacement shoe
Replacement bumper
WIDE SLOT – With rubber bumper
and plain metal shoe. General cleaning
of medium to heavy pile. Allows for
passage of large debris.
Replacement shoe
Replacement bumper
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
15" Wide
VTL90009
(1200)
1.00 lb.
VTL90010
(1500)
1.25 lb.
SHV90002
BUF90003
SHV90006
BUF90005
VTL90011
(1201)
1.00 lb.
VTL90012
(1501)
1.25 lb.
VTL90013
(1202)
1.00 lb.
VTL90014
(1502)
1.25 lb.
SHV90003
BUF90003
SHV90009
BUF90005
SHV90000
BUF90003
WIDE VENTS – With rubber bumper
and vented shoe for increased surface
flow. For wool and synthetic shag.
Especially useful when threads and lint
are prevalent.
Replacement shoe
Replacement bumper
4
12" Wide
◆
FAX 860.688.0098
SHV90007
BUF90005
◆
www.spencerturbine.com
11/2" CARPET TOOLS
Carpet tools are used at the end of a wand.
Replacement part numbers are listed in blue italic.
BRUSH INSERT – With rubber bumper
and nylon bristle strip. For imbedded
dirt on indoor/outdoor or other short
pile carpets.
Replacement shoe
Replacement bumper
12" Wide
15" Wide
VTL90015
(1203)
1.19 lb.
VTL90016
(1503)
1.44 lb.
SHV90001
BUF90003
SHV90008
BUF90005
11/2" WALL AND OVERHEAD TOOLS
Wall and overhead tools are designed for use with wall handles or hose connectors.
For additional flexibility use 45° gooseneck elbow with these tools.
Replacement part numbers are listed in blue italic.
4" ROUND BRUSH – Nylon.
Recommended for general cleaning
of mouldings and irregular surfaces
in small areas.
Replacement brush
Replacement bumper
VTL90044
(930)
.75 lb.
BRS90029
BUF90000
6" PIPE BRUSH – Nylon bristle strip
in center of slot. Allows dust to be
loosened and drawn away without
falling to the floor.
Replacement brush
VTL90055
(2040)
1.13 lb.
BRS90023
WALL BRUSH – Horsehair.
Recommended for paneled or painted
walls or any smooth surface.
Replacement brush
PIPE AND LEDGE BRUSH – Nylon.
Designed for overhead cleaning of
pipes and ledges with heavy dust
accumulation.
Replacement brush
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
15" Wide
VTL90068
(1990)
1.50 lb.
BRS90015
VTL90070
(1615)
1.75 lb.
BRS90013
6" Wide
11" Wide
VTL90059
(1865)
1.25 lb.
VTL90060
(1860)
1.50 lb.
BRS90011
45° GOOSENECK ELBOW –
Aluminum. Connects wall handle or
hose connector to wall or overhead tools.
The Spencer Turbine Company
101/ 2" Wide
◆
BRS90012
EVT90008
.28 lb.
FAX 860.688.0098
◆
www.spencerturbine.com
5
11/2" PLASTIC TOOLS
FLOOR TOOLS
These high impact molded plastic floor tools are used at the end of a wand.
Replacement part numbers are listed in blue italic.
*Quantity (2) required.
**Quantity (4) required.
SCALLOPED VENTS – With rubber bumper.
Most effective on short and medium pile carpets.
Replacement bumper
NYLON BRISTLES – For cleaning sticky dust
from hard floors or rough, uneven surfaces.
Replacement brush
TAMPICO BRISTLES – For removing caked
dirt or sticky material.
Replacement brush
FELT BLADES – For cleaning polished wood,
linoleum, or other smooth surfaces.
*Replacement blade
FIBER BLADES – For cleaning unfinished wood,
rough or abrasive surfaces.
*Replacement blade
DOUBLE-BLADED SQUEEGEE – For liquid
recovery. Two neoprene rubber blades.
*Replacement blade – neoprene
**Replacement metal holder
14" Wide
VTL90067
.88 lb.
BUF90009
VTL90064
1.00 lb.
BRS90019
VTL90065
1.00 lb.
BRS90020
VTL90062
1.00 lb.
SVT90022
VTL90063
1.25 lb.
SVT90023
VTL90066
1.58 lb.
BLV90004
SVT90024
HAND TOOLS
These tools attach directly to the female hose coupling.
Replacement part numbers are listed in blue italic.
CORNER & CREVICE – For cleaning narrow
and difficult to reach areas.
5" UPHOLSTERY – For fabrics and small areas
with slide-on nylon brush end.
Replacement brush
VTL90000
(1470)
.56 lb.
VTL90061
.50 lb.
BRS90021
This tool is designed to connect directly to a 11/2" female hose coupling.
41/2" AUTO CLEANING TOOL with BUSHING –
Designed with narrow slot to reach in between
seat and consoles.
VTL90099
.32 lb.
This tool is designed to fit directly into the inside diameter of a 11/2" hose with cuff.
41/2" AUTO CLEANING TOOL – Tool design same
as VTL90099 without bushing.
6
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
VTL90085
.31 lb.
◆
www.spencerturbine.com
11/2" WANDS
Effective curves and a knurled locking nut allow the
operator to reach normally inaccessible areas without
moving obstacles. These wands are designed for
both wet and dry service.
HDL90036
HDL90035
HDL90038
HDL90062
Two standard lengths of 52" and 58" are available to suit
application or operator preference.
52" CHROME PLATED – Steel. To be
used with any elbow joint, hose connector
or elbow connector. Heavy duty industrial
service or for cleaning congested areas.
HDL90036
(1297S)
2.50 lb.
58" CHROME PLATED – Steel. To be
used with any elbow joint, hose connector
or elbow connector. Heavy duty service
or for congested areas.
HDL90035
(1297)
2.75 lb.
58" CHROME PLATED – Steel. Connects
directly to a 11/2" female hose coupling
or any elbow joint.
HDL90038
3.50 lb.
52" SATIN ANODIZED – Aluminum. To be
used with nickel-plated elbow joint, elbow
connector, or hose connector. Lighter in
weight—used for general service.
HDL90033
(1295S)
1.00 lb.
58" SATIN ANODIZED – Aluminum. To be
used with any nickel-plated elbow joint,
hose connector, or elbow connector. Lighter
in weight—used for general service.
HDL90034
(1295)
1.13 lb.
58" SATIN ANODIZED – Aluminum.
Connects directly to a 11/2" female hose
coupling or any nickel-plated elbow joint.
POWER BRUSH (VTL90089) Pictured
52" anodized aluminum floor handle.
Use with female hose coupling.
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
HDL90037
(1298)
1.63 lb.
HDL90062
10.00 lb.
www.spencerturbine.com
7
11/2" WALL HANDLES
anodizing prevents oxidation. All wall handles must
be used in conjunction with an elbow joint, elbow
connector, or hose connector (see pages 9 and 10).
Light weight aluminum wall handles are used for
overhead wall and pipe cleaning, or difficult to reach
areas. Two- and four-foot sections may be combined
for the most convenient length. Attractive satin
TWO-FOOT EXTENSION –
With 45° nickel-plated elbow and knurled locking nut.
HDL90040
(1370)
.75 lb.
FOUR-FOOT STRAIGHT EXTENSION –
With knurled locking nut.
HDL90013
(2000)
1.00 lb.
FOUR-FOOT EXTENSION –
Slip-fit design to be used with either the
HDL90040 or HDL90013 wall handles.
(Does not accept tool directly.)
HDL90019
(1365)
.75 lb.
CONCENTRIC TUBE GULPER TOOL
Note:
This end slides
directly into bare
(no coupling) hose
and uses hose
clamp.
CONCENTRIC TUBE GULPER TOOL –
Carbon Steel painted blue. Designed with air bleed system allowing tool end
to be buried in material being conveyed. Slides directly into hose i.d. sizes
11/2", 2", 21/2", 3", 31/2", 4". Available in other materials of construction.
Consult factory.
Size
1 /2"
2"
21/2"
1
8
The Spencer Turbine Company
P/N
VTL90100
VTL90102
VTL90103
◆
Size
P/N
3"
31/2"
4"
600 Day Hill Road, Windsor, CT USA 06095
VTL90104
VTL90105
VTL90106
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
www.spencerturbine.com
11/2" ELBOW JOINTS
locking nut. They provide the ultimate connection
between hose and handle.
Elbow joints are designed for connecting hose to a
wand or wall handle. These uniquely designed elbow
joints combine a ball bearing swivel and a knurled
■ Provides operator with handlegrip.
■ Prevents hose twisting.
■ Reduces hose wear at point of maximum stress.
■ Allows hose to hang freely.
■ Shut-off valve conserves energy.
■ Reduces operator effort.
NICKEL-PLATED MALLEABLE IRON – With
shut-off valve, hose swivel and locking nut—
for heavy duty service.
EVT90003
(1255)
2.50 lb.
NICKEL-PLATED ALUMINUM – With shut-off valve,
hose swivel and locking nut—for general service.
NICKEL-PLATED ALUMINUM – With locking nut—
for general service.
NICKEL-PLATED ALUMINUM – With hose swivel
and locking nut—for general service.
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
EVT90002
(1380)
1.50 lb.
ENJ90001
(1660)
.88 lb.
ENJ90002
(1661)
1.00 lb.
◆
www.spencerturbine.com
9
11/2" HOSE CONNECTORS
Hose connectors are designed for connecting hose to a wand, wall handle, or directly to a tool with a knurled locking nut.
ALUMINUM STRAIGHT – With locking nut.
VTL90078
(189)
.50 lb.
ALUMINUM STRAIGHT –
With shut-off valve and locking nut.
VTL90079
(890)
.88 lb.
11/2" ELBOW CONNECTOR
45° elbow connector for connecting hose to wand or floor handle.
NICKEL PLATED MALLEABLE IRON –
With aluminum swivel and locking nut.
EVT90004
(2295)
1.13 lb.
11/2" FLOOR ELBOW
90° elbow for connecting hose to floor valves (VLV90110, VLV90112, VLV90227, VLV90246, VLV90233,
VLV90237 or equivalent lock-type valve). Eliminates hose strain and allows for 360° swivel.
ALUMINUM – Equipped with inlet valve
VLV90082 (Type "B").
10
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
EVT90005
(1325)
1.75 lb.
◆
FAX 860.688.0098
◆
www.spencerturbine.com
2" EQUIPMENT
All 2" equipment is designed for extra heavy duty industrial service
where large accumulations of dirt and litter are encountered.
Replacement part numbers are listed in blue italic.
*Quantity (2) required.
5" GULPER – Aluminum. Fits directly into female
coupling for large accumulation of material.
TOOLS
VTL90048
(1835)
2.25 lb.
5" GULPER – Aluminum. Permanently attached to
chrome plated steel wand. Connects directly into
2" Female Hose Coupling.
VTL90049
(1836)
5.50 lb.
15" BARE FLOOR – Steel sides. To be used at the
end of a wand. For scraping or severe service or rough
abrasive floors.
*Replacement side
VTL90057
(2030)
2.75 lb.
SVT90011
15" BARE FLOOR – Rubberized sides. To be used
at the end of a wand. For unfinished wood floors or
rough surface. Also used for liquid removal.
*Replacement side
VTL90058
(1240)
2.38 lb.
SVT90018
WAND
52" CHROME PLATED – Steel. To be used with 2"
elbow connector (VTL90072) and 2" tools.
ELBOW CONNECTOR
HOSE ADAPTERS
11/2"
2"
11/2"
2"
The Spencer Turbine Company
◆
HDL90039
(1225)
3.25 lb.
45° ELBOW CONNECTOR – For connecting hose
to a wand. Nickel-plated aluminum with hose swivel
and locking nut.
VTL90072
(1875)
1.38 lb.
HOSE ADAPTER – Allows 2" hose to connect to a
11/2" inlet valve or 2" tool set to connect to a 11/2"
I.D. hose.
VTL90082
(1850)
.75 lb.
HOSE ADAPTER – Allows 11/2" hose to connect to a
VLV90100 or 11/2" tool set to connect to a 2" I.D. hose.
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
VTL90073
(1957)
.88 lb.
www.spencerturbine.com
11
HOSE
Consider the application, the size and service requirements when selecting a hose.
11/4" I.D. hose is recommended for light commercial duty.
It is lightest in weight and with superior flexibility.
11/2" I.D. hose is the most common and used for average
vacuum cleaning applications.
2" I.D. hose is recommended for large quantities or bulky
materials.
Note: For other diameter hose or special applications —
consult factory.
Hose Type
“CHIC”
Medium-Duty
Polyethylene
“TUFF-FLEX”
NON STATIC RESISTANT
11/2"
2"
11/4"
11/2"
2"
11/2"
“KLAM”
11/2"
Heavy-Duty
Urethane
“SPENCER-FLEX”
Heavy-Duty
Vinyl
“PYTHON”
Heavy-Duty
Rubber
12
“RHINO”
The Spencer Turbine Company
HOSE ASSEMBLIES (EXCEPT TUFF-FLEX AND YELLOW
CAR CARE PRODUCTS) ARE TESTED FOR ELECTRICAL
CONDUCTIVITY TO ASSURE STATIC ELECTRICITY IS MINIMIZED.
Inside
Diameter
Light-Duty
PVC
Heavy-Duty
PVC
Both the 11/4" and 11/2" I.D. hoses are used with our 11/2"
attachments. 2" I.D. hose is used with 2" attachments.
Hoses are supplied with one male and one female
coupling. The male coupling connects into the inlet valve;
the female coupling connects directly to tools or attachments. Hoses may be joined for additional length using
the standard male and female couplings.
◆
121/2'
Lengths and Part Numbers
25'
371/2'
50'
HOS90164
HOS90166
HOS90168
HOS90170
HOS90176
HOS90178
HOS90180
HOS90182
HOS90077
HOS90078
HOS90079
HOS90080
HOS90081
HOS90084
HOS90088
HOS90188
HOS90082
HOS90085
HOS90089
HOS90190
HOS90212
HOS90086
HOS90090
HOS90192
HOS90083
HOS90087
HOS90091
HOS90194
2"
HOS90200
HOS90202
HOS90204
HOS90206
11/2"
HOS90241
HOS90243
HOS90245
HOS90247
11/2"
HOS90101
HOS90103
HOS90105
HOS90107
2"
HOS90109
HOS90111
HOS90113
HOS90115
11/2"
HOS90117
HOS90119
HOS90208
HOS90121
2"
HOS90123
HOS90125
HOS90210
HOS90127
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
www.spencerturbine.com
CAR CARE KIT
Convenient all-in-one operator package with
15' long, 11/2" diameter yellow plastic hose,
coupling, duck foot cleaning tool and tool holder.
KAC90104
Same as above with static resistant hose.
Replacement rubber backing
RUB90001
KAC90108
Weight
(lbs./ft.)
Vacuum
Rating
"Hg
Color
Flexibility
Grey
Excellent
.26
26
.37
25
Grey
Excellent
.41
20
Blue
Excellent
.28
.50
Grey
25
12
Blue
Durability
Application
Commercial, Light
Industrial Duty, Offices
(Temp Range:
–20° to +150°F)
Fair
Fair
Excellent
Good
Excellent
Good
Good
20
Orange
Excellent
Good
.40
28
Blue
Good
Very Good
.50
28
Blue
Good
Very Good
.32
24
Blue w/ Black
Very Good
Excellent
.50
29.8
Blue
Very Good
Very Good
.60
29.8
Blue
Very Good
Very Good
.7
28
Black
Good
Excellent
.9
28
Black
Good
Excellent
.41
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
Construction
Fiber-reinforced
PVC Hose Cover
Spring Steel Helix
Static Resistant
General Vacuum
Cleaning, Commercial,
Car Wash, Offices
(Temp Range:
–20° to +150°F)
Polyethylene
Two-Piece Construction
Crush Proof
General Service,
Schools, Industrial
Cleaning
(Temp Range:
–22° to +104°F)
PVC Compound
Plastic Helix
Copper Ground Wire
Abrasion Resistant
Static Resistant
General Service,
Industrial Cleaning,
Schools
(Temp Range:
–40° to +170°F)
General Service,
Schools, Hospitals,
Clean Rooms
(Temp Range:
–20° to +120°F)
Industrial and Heavy
Commercial Vacuum
Cleaning in Factories,
Foundries
(Temp Range:
–40° to +200°F)
TEL 860.688.8361
◆
FAX 860.688.0098
PVC Helix
Urethane Core
Abrasion Resistant
Copper Ground Wire
Chemical Resistant
Static Resistant
Smooth Vinyl Cover
Steel Wire
Nylon Yarn
Foam Inner Wall
Chemical Resistant
Static Resistant
Braided SS Ground Wire
Nitrile Rubber Tube
Abrasion Resistant
Neoprene Cover
Oil Resistant
Static Resistant
◆
www.spencerturbine.com
13
WALL INLET VALVES FOR 11/2" DIAMETER HOSE
Inlet valves provide a quick connection of the male
hose coupling to the piping system or separator. The
cover is self-closing and includes a hook to prevent the
hose from being pulled out. Valve bodies are forged
brass, covers are steel, and the entire valve is nickel
plated.
Four basic valves are available. Each may be fitted with
a standard or recessed escutcheon plate. The basic
valves are used with exposed piping in basements, on
concrete walls, in factories or on separators.
The standard wall flange is recommended for most
typical installations. Valve protrusion into the room is
only 1 inch. Furthermore, the face of the threaded
connection can be as little as 13/16 of an inch from the
wall — advantageous where space is limited.
The recessed flange is recommended for areas using flush
wall design. It is considered a more attractive installation.
Optimum mounting height of wall valves is 18 to 20 inches above floor level. NOTE: Optional lock type covers
are available.
2" male thread-exposed pipe. The popular
(standard) valve. 211/32" long.
VLV90083
(VLV90091 Lock Type)
(8720-Type E)
1.13 lb.
2" female thread-exposed pipe.
213/32" long.
VLV90101
(VLV90102 Lock Type)
(8815-Type E)
1.50 lb.
2" male thread VLV90083 with “standard”
flange.
VLV90084
(VLV90093 Lock Type)
(8705-Type D)
1.50 lb.
2" female thread VLV90101 with
“standard” flange.
VLV90103
(VLV90104 Lock Type)
(8805-Type D)
1.78 lb.
2" male thread VLV90083 with “recessed”
flange.
VLV90085
(VLV90095 Lock Type)
(8705A-Type DA) 1.63 lb.
2" female thread VLV90101 with
“recessed” flange.
VLV90105
(VLV90106 Lock Type)
(8810A-Type DA) 1.75 lb.
2" male thread-exposed pipe with short
body. 17/8" long.
VLV90087
(VLV90092 Lock Type)
(8730-Type E)
1.00 lb.
11/ 2" male thread-exposed pipe. Use when
a 11/ 2" thread must be used. 27/16" long.
VLV90082
(VLV90090 Lock Type)
(8740-Type B)
1.13 lb.
2" male thread VLV90087 with “recessed”
flange. For limited wall space.
VLV90086
(VLV90096 Lock Type)
(8715A-Type DA) 1.25 lb.
11/ 2" male thread VLV90082 with
“recessed” flange.
VLV90098
(VLV90099 Lock Type)
(8745A-Type CA) 1.25 lb.
11/ 2" male thread VLV90082 with
“standard” flange.
VLV90089
(VLV90097 Lock Type)
(8745-Type C)
1.25 lb.
2" male thread VLV90087 with “standard”
flange. For limited wall space.
VLV90088
(VLV90094 Lock Type)
(8715-Type D)
1.25 lb.
304SS “recessed” flange to fit VLV90239.
FLG90024
0.3 lb.
304SS version of an 8720 Type E inlet
valve with 2" male thread valve.
VLV90239
1.13 lb.
14
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
304SS “standard” flange to fit VLV90239
(Not Shown).
FLG90025
0.2 lb.
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
www.spencerturbine.com
FLOOR INLET VALVES FOR 11/2" DIAMETER HOSE
When it is inconvenient to use wall valves, floor
valves are available. The valve is made of forged
brass with a natural brush finish. It is designed to
maintain its original appearance even in heavy
traffic areas. It is recommended that the hose be
connected to these valves using a Part No.
EVT90005 floor elbow.
2" male thread – Installed flush with
floor surface.
2" male thread – Beveled edge
designed for use with carpets.
Chrome plated version of a VLV90110
Type G floor valve.
304SS version of a VLV90110
Type G floor valve.
VLV90110 (VLV90111 Lock Type)
(8900-Type G)
1.88 lb.
VLV90246
VLV90112 (VLV90113 Lock Type)
(8905-Type R)
1.88 lb.
1.9 lb.
1.9 lb.
VLV90227
LOCKING VALVES
“Easy-Lift” keyless floor valve.
VLV90449
Complete valve (chrome body
with aluminum cover/lid)
Optional lock type covers
can be furnished on all wall
and floor inlet valves
designed for use with 11/2"
diameter hose.
LIV90036
Aluminum cover/lid only
(replacement for existing valves)
INLET VALVES FOR 2" DIAMETER HOSE OR LARGER
The 2" valve body is forged brass. The cover is steel
and the entire valve is nickel plated. 2 1/2" and larger
valve bodies are carbon steel. The covers are forged
brass and the entire body is nickel plated.
3" male thread-exposed pipe.
Accepts 3" male hose coupling.
2" male thread-exposed pipe.
Accepts 2" male hose coupling.
VLV90100
(8755-Type I)
VLV90108
(8675-Type L)
1.25 lb.
4" male thread-exposed pipe.
Accepts 4" male hose coupling.
21/2" male thread-exposed pipe.
Accepts 21/2" male hose coupling.
VLV90107
(8690-Type J)
4.25 lb.
VLV90109
(8676-Type K)
2.75 lb.
6.25 lb.
5", 6" and 8" inlet valves are also available.
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
www.spencerturbine.com
15
SILENT VALVE
This valve is designed for use with 11/2" diameter
VLV90115
hose to minimize noise when the hose is either
(8910)
being inserted or removed. It is therefore ideal for
3.50 lb.
use in hospitals, rest homes, libraries, dormitories
and schools to control noise level.
The flush mounting is especially desirable in hospital corridors
where there is a heavy stretcher and wheelchair traffic.
VACUSLOT FLOOR VALVES
A unique cleaning system is available wherever dry
mops or push brooms are used. Spencer provides a
floor slot that collects dirt accumulations and sweepings, as well as cleaning the mop itself. Dirt and litter
pushed near the slot are carried by vacuum, through a
tube system into a collector.
The convenience of a central vacuum cleaning system
is available if the vacuslots are equipped with valves
for hose connections.
Vacuslots are designed for flush floor installations.
They are made of heavy aluminum plate with a
burnished finish.
Vacuslots are ideally suited for schools, hospitals,
offices, or any building with smooth floor coverings.
Round Style—
Dry mop slot only.
Square Style—
Dry mop slot only.
VLV90231
(2785-Type F)
13 lb.
VLV90235
(2786-Type FR)
13 lb.
Square Style—
Dry mop with valve.
Accepts 11/2" male
hose coupling.
Round Style—
Dry mop with valve.
Accepts 11/2" male
hose coupling.
Lock
VLV90234
Lock
VLV90238
Lock
VLV90236
Lock
VLV90232
VLV90237
(2820-Type FGR)
13 lb.
VLV90233
(2821-Type FG)
13 lb.
VALVE INSTALLATION TOOL
WRN90000
This tool is designed to fit directly into the body of a
Spencer wall or floor inlet valve for 11/2" or 2" hose. The
opposite end of the tool may be gripped with a wrench,
thereby allowing the installer to easily thread the valve into
the piping system. Cast iron. 2 lb.
16
The Spencer Turbine Company
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
www.spencerturbine.com
ACCESSORIES
HOSE AND TOOL CABINET
Steel compartment for storing
hose and tools. Dimensions:
24" x 24" x 72", mounted on
5" legs.
VTL90083
(2370)
175 lb.
(shown with optional hose
and tools.)
HOSE AND TOOL
CART
Steel construction with
wheels includes hose
rack, 10 tool holding
positions, tool bin and
storage tray.
Dimensions: 301/4" wide,
493/8" high and 315/8"
long.
RKV90011
115 lb.
(shown with optional
hose and tools.)
HOSE RACKS
For storage of hose.
Cast Aluminum –
Wall mount
RKV90000
(2360)
3 lb. (193/4" x 6")
HOSE REPAIR COUPLINGS
11/2" female hose repair
coupling for 11/4" hose
CPL90246
(1101)
Cast Aluminum – Column
mount with backing plate
RKV90002
(2359)
3.25 lb. (193/4" x 6")
.47 lb.
11/2" male hose repair
coupling for 11/4" hose
CPL90193
(1102)
Cast Aluminum –
Wall mount-Double
RKV90003
(2361)
6 lb. (193/4" x 12")
.41 lb.
11/2" female hose repair
coupling for 11/2" hose
CPL90244
(1001)
.47 lb.
11/2" male hose repair
coupling for 11/2" hose
Sheet Steel
RKV90001
1.75 lb. (9" x 6")
CPL90191
(1003)
304 Stainless Steel
RKV90007
4.75 lb. (161/2" x 61/4")
2" female hose repair
coupling for 2" hose
Steel and neoprene. Combines
tool storage and vacuum shutoff for cast aluminum 6" hand
tool. Bleed orifice available.
TOOL HANGER
RKV90004
(1787)
CPL90189
(1002)
.75 lb.
2" male hose repair
coupling for 2" hose
2.75 lb.
CPL30056
(2723C)
.625 lb.
RKV90005
(with bleed orifice)
The Spencer Turbine Company
.41 lb.
◆
600 Day Hill Road, Windsor, CT USA 06095
◆
TEL 860.688.8361
◆
FAX 860.688.0098
◆
www.spencerturbine.com
17
Spencer Corporate Headquarters and Manufacturing Plant, Windsor, CT USA
Spencer Products and Services
Industrially rated products offering effective
solutions for air and gas handling applications:
Comprehensive engineering and other
customer support services:
•
•
•
•
•
•
•
•
• The industry’s largest complement of technical
specialists in air and gas technology
• Global parts and service organization
• Application research and testing facility
Modular central vacuum systems
Mobile or stationary integrated vacuum units
Dust collectors and separators
Multistage centrifugal blowers
Single-stage centrifugal blowers
Regenerative blowers
Gas boosters
Custom-engineered products with special materials
for extreme temperatures and pressures
Complementary accessories with single
source convenience and compatibility:
• Standard and custom electrical control panels –
UL, CUL Listed and C.E. Compliant available
• Comprehensive selection of tubing, fittings, vacuum
hoses, valves and tools
• Valves, gauges, couplings, shrink sleeves, vibration
isolators and other system components
Sump-Vac® is a registered trademark of The Spencer Turbine Company.
Global organization of sales representatives
and distributors offering:
• Product selection, installation and operation
assistance
• Comprehensive system design services
• Follow-up services and troubleshooting
For the name and telephone number of your
local Spencer representative, call 800-232-4321
or email marketing@spencer-air.com.
Visa, MasterCard and
American Express welcome
Blowers & Vacuum Systems with an Engineering Edge
The
Turbine Company, 600 Day Hill Road, Windsor, CT 06095 USA
TEL 800-232-4321 ◆ 860-688-8361 ◆ FAX 860-688-0098 ◆ www.spencerturbine.com
Bulletin No. 241R.2
Copyright ©2013 The Spencer Turbine Company
040113KBA1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising