XP33 – 3 Channel Dimmer

XP33 – 3 Channel Dimmer
concept
XP33LR - XP33U
2000 Xp
7.1
Dimmers type XP33
XP33LR: Three-channel dimmer 3x240 VA ohms inductive
EAN-Nr. : 5703513058982
2
4
6
8 10 12
home and building automation
Module No
LEADING EDGE DIMMER XP33LR
3 x 210 VA - 240V ~ 50Hz
3 x 105 VA - 110V ~ 60Hz
STATUS
XP33LR is a 3-channel dimmer for dimming resistive and inductive charges. The
XP33LR regulates logarithmically and has a built-in soft-start, thermal protection
and reporting of neutral interruption. The total power of the three channels is 640
VA. One channel can take 500 VA, and the rest is has to be distributed to the other
two dimmers. The XP33LR owns 5 immediate impulse inputs, three in order to
dim of the three channels, one to dim all three together and on/off, and one to
select from four preset scenes. At commissioning of the data-bus, up to 99
programmed functions are performed for the realization of modes, and this by
using dimming actions by percent, up and down, time and fade functions.
B C D E F G H I K L
XP33U: Three-channel dimmer 3 x 210 VA ohms inductive capacitive
EAN-Nr. : 5703513057749
2
4
6
8 10 12
(If not available to replace XP33LR)
home and building automation
Module No
UNIVERSAL DIMMER XP33U
3 x 210 VA - 240V ~ 50Hz
3 x 105 VA - 110V ~ 60Hz
STATUS
B C D E F G H I K L
www.conson.com
XP33U is a universal 3-channel dimmer for control of resistive, inductive and
capacitive loads and short-circuits. The XP33U regulates logarithmically and has
a built-in soft-start, thermal protection and reporting of neutral interruption.
Each of the three channels can control a load of up to 210VA. The XP33U owns 5
immediate impulse inputs, three for dimming the three channels, one for
dimming all three together and one to choose from one of four preset scenes. At
commissioning of the data-bus, up to 99 programmed functions are performed
for the realization of modes, and this by using dimming actions by percent, up
and down, time and fade functions.
home and building automation
concept
XP33LR - XP33U
2000 Xp
7.2
Dimmers type XP33
Connections of the XP33
Connections high power of the XP33
Connections low power: control via direct
inputs and LED outputs
L
L1
L2
L3
1
2
3
L
N
Connections high power of the XP33
Connections low power: Control via the
Consonbus
PE
N
L
L
L1
L2
L3
1
2
3
Power
regulation
IR
com
Electronic control
Power
regulation
ClockData
N
Electronic control
ClockData
B C D E F G H I K L
Plus (+) 24VDC
Minus (-)
Data
Clock
4-wires signalization cable
led-output ch 3
led-output ch 2
led-output ch 1
on/off + dimming ch 3
on/off + dimming ch 2
on/off + dimming ch 1
select scene 1 to 4
all outputs
on/off + dimming
B C D E F G H I K L
PE
N?
%?
t°
N?
%?
t°
IR
com
N
2
3 1 5
4
XP2506
to next interfaces
www.conson.com
home and building automation
concept
XP33LR - XP33U
2000 Xp
7.3
Dimmers type XP33
General characteristics of the XP33-dimmers
Dimmers XP33 have a microprocessor for progressive regulation. Special features inter alia, soft-start, adjustable fade-in and
fade-off times, thermal security, logarithmic arrangement,
potentiometer-control, analog daylight-dependent control,
slave control, security against neutral-break and a minimum
and maximum setting without adjustment-potentiometers.
Softstart and fade-in and fade-uit
When switching on the dimmer, the output voltage goes from
zero to the last used or desired level and this according to a
certain amount of time defined in the software of the module.
This working method prevents brutal interference on the mains
when switched on and extends the life of the lamp. In addition,
a timely limitation is ensured by a short-circuit during the
breakage of the filament. The fade-in and fade-off times can be
accessed via the bus and this with actions ranging from 5
seconds to 2 hours.
Thermal protection
This limits the temperature inside the module. The level of
limitation is dependent on the type of dimmer. If this temperature is exceeded, the dimmer sends an SOS signal. Because of
the SOS signal, the LED-dimmer flashes in rhythm of 3 x short
and 3 x long. This signal is also present at the output of the LEDdimmer module. During the SOS signal, the output level is
adjusted downwards. The reset is done by activating the
impulse input of the dimmer for 20 seconds, or by removing the
power supply voltage 24 VDC. This protocol can be different
according to type of dimmer.
Protection against short-circuit
The dimmer of the CR and U are short-circuit proof. The power of
these dimmers is controlled by the power mosfet-transistors.
These are fast enough to switch off their load.
Logarithmic control
The dimmers have a logarithmic regulation which ensures that,
when being operated, an ergonomic feeling arises between the
operation and the determination of the light variation.
Protection against neutral-break
A disconnected or interrupted neutral is indicated by the LED
on the dimmer. This light flashes rhythmically, followed by a
long pause. In this mode, the dimmer will not work. These
security includes inter alias the following advantages: it must
connect properly so that the filter network is functioning
(interference suppression to the mains and vice versa) and it
protects the component against overstrain (e.g. 380V instead of
230 V).
A neutral-break from the base means that there is a high tension
in certain light grids on the load and thus cannot simply be
transferred to the load. More so, Conson has deliberately opted
for sustainable control components that can withstand1000V.
www.conson.com
Power loss of a dimmer
The choice and quality of the components contribute to a
minimal power loss of 1% to the load. Thus, the power loss
depends on the load used. The larger the load, the higher the
power loss. With LED lighting, this is negligible in practice.
However, the power loss of a dimmer must always be taken into
account. It develops heat inside the electrical enclosure and can
be discharged by natural ventilation.
Important remark:
Always insert the dimmers at the bottom of the enclosure. Thus,
this cannot be heated by other components.
Minimum and maximum level
The minimum and maximum level is adjustable via the direct
input or via the ConTool software. Setting the minimum is
particularly useful when the light source is hidden in its
armature (one cannot see the filament or others, e.g. uplighters).
May also be useful for the minimum speed of fans. Through the
ConTool software, one can decided that the first dimmer is
directed towards the maximum, such that the engine get to its
speed.
The maximum is useful in terms of energy savings. The
difference between 95% and 100%, is hardly visible.
Scene control
The purpose of the XP33 dimmer is to use this dimmer in one
and the same room where 3 elements are installed. It is easier to
program four different scenes (modes) in advance and ensure
that they can be recalled in a fairly simple way. Thus, the user
does not always have to push several buttons. Scenes such as
watching TV, cleaning the room, reading a book, dining, etc.. If
one needs only 2 points of light in a room, one can isolate the
third output of the other two outputs. How to proceed is
described below.
home and building automation
concept
XP33LR - XP33U
2000 Xp
7.4
Dimmers type XP33
Programming the dimmers XP33 via ConTool
Start the ConTool program and create a new project. As an
example, we take the project „Villa Seascape”. The entered
names are fictitious, but serve as a guide through the example.
Place a checkmark in the „Off line” (1) and then press „OK” (2).
8
4
3
5
1
2
6
The ConTool-program starts with a blank worksheet. Before
continuing, it is necessary to add a floor plan. In our example, by
means of the Windows Explorer, a floor plan was copied to the
„Floor Plan Images” directory. This directory is located in the
root directory of the ContoolXP.
Remark: The file extension may be one of the following: jpeg.,
gif., jpg. or bmp.. The most CAD-programs can perform this
conversion. A drawing on paper may also be used by simply
photographing and copying the drawing beneath the above
directory.
In the right pane, click on „Add” (3) and a standard floor plan
appears on the worksheet. If he floor plan is charged, then
proceed as follows: Choose the button „ ... ” (4). A window
„Open” (5) appears. Select the desired floor plan. Press „Open”
(6).
After pressing „Open” (6), a window with the message „Select
Import Size of Image” appears again. The size of the floor plan
can be customized. The most simple choice is „Stretch to fit
hidden right panel”. Press „Ok” (7). The floor plan appears and
this at full screen width. With the arrows (8) on the left at the
height of the right panel one can change the screen content
and the size. Only the floor plan or only the right panel, or both.
Clicking on the arrows or dragging the left side of the right
panel.
7
www.conson.com
home and building automation
concept
XP33LR - XP33U
2000 Xp
7.5
Dimmers type XP33
Programming the dimmers XP33 via ConTool
At the top left of the tab select „Settings” and a drop menu
appears – add a check mark at „Automatic connection”. Go to
the „Design state” (9) tab - select the tab „Sensors/actors” (10) –
click the selection button „Actors lamp Xp” (11) - a drop down
menu opens, select „XP33 lamp” - now drag this lamp to the
floor plan, click on the place where it should be located. Do this
three times, see below. As long as the mouse pointer can be
seen on the floor plan, it is to place a lamp. Once the pointer is
outside the worksheet, the working stops. By using the mouse,
an item can always be moved.
At the top, select the tab „Fusebox” (14). A XP33-module
appears. The outputs (15) report their location. These are
written in light-gray.
14
9
10
15
11
Due to the fact that in „Settings” the program is not set to
„Automatic connection” a window (12) always is opened after
placing a circle of light. Place a checkmark next to the first
output of the XP33 (13) and give it a name, e.g. Central SLK 1. Do
the same for the wall light and the light above the bed. Each
time, press „Ok”.
Return to „Floorplans” – „Design state” – „Sensors/actors” - click
on the selection key pushbuttons Xp - choose a Buspushbutton XP2506 and drag it to the floor plan and place it at
the door entrance (16) of the bedroom 1. Insert also a XP2506 at
the left of the bed (17).
12
16
13
Bedroom
17
Remark: It is useful to save the project from time to time. Select
the tab „File“ and „Save”.
www.conson.com
home and building automation
concept
XP33LR - XP33U
2000 Xp
7.6
Dimmers type XP33
Programming the dimmers XP33 via ConTool
Go to „Programming state” and select the bus-pushbutton at
the door entrance of SLK 1. The following window appears.
On the floor plan (21) is graphically shown that there is a
relationship between the center pushbutton and three light
circles in the bedroom.
Press the top left button and name it “All 100%”. When this
button is activated, it means that one can address an actor.
Select the circle of light „Bedroom wall” and the actor XP33window opens. Choose the “Scene 2” (22) function and press
„Ok”.
18
20 22
19
Enter the location (18) „Bedroom door” and select the middle
button of the XP2506. As long as no location is specified, one
cannot continue the procedure. A warning screen will appear.
By clicking on the middle button, it takes on a purple color. The
default name is „GO” (19), but it can be replaced by „Welcome to
the bedroom”. When this button is activated, it means that one
can address an actor. Select the lamp „Central SLK2” and the
actor XP33-window opens. Choose the „Scene 1” (20) function
and press „Ok”.
www.conson.com
21
And one can go on for the other pushbuttons. With the push
button right below, one can simply turn off all the lights by
granting, one by one, the action „Off” to the three circles of light.
Hereafter follows how various scenes are set.
home and building automation
concept
XP33LR - XP33U
2000 Xp
7.7
Dimmers type XP33
Programming the dimmers XP33 via ConTool
Go to the tab „Fusebox” and right click on the XP33 - a menu
appears - select „Setup Module” - The „XP33 module
programming” (23) opens.
Technical data
XP33LR / U
23
High current
Power supply
110/230 VAC 50/60Hz
Minimum and maximum load
XP33LR
Total maximum of the three outputs: 640 VA
Maximum of one output: 500VA – rest has to be distributed
XP33U
3 x 200 VA
Own loss per output
< 1%
Rise time (soft start)
500 ms
Off time
750 ms
Fuse that has to be used
maximum 10 A
24
25
26
Low current
Current decrease at rest at 24 VDC
Consumption at rest at 24 VDC
Input current of all inputs
Impulse time all inputs
Mechanical data
Montage
Measurements
10,8 mA
0,026 W
0,5 mA
tss 50-300 msec
Din-rail DIN46277
85x70x72 mm
27
28
The different scenes (25) from 1 to 4 can be set with the sliders of
the three outputs. In our example of the bedroom, scene 1 was
assigned to the middle button. Adjust the sliders so in accordance with the result that gives the best impression when
entering the bedroom.
With the establishment of the fade time-scene (26) one obtains
a soothing effect to go from one scene to another. This can be
useful in a bedroom when one awakens or goes to bed simply
by choosing a low-light-level scene while the action „Off after Xtime” is ascribed to all three outputs, possibly with different
durations. The check-boxes (27) of the outputs have to isolate
one or two outputs of the various scenes. The check-boxes (28)
can ensure that a certain output starts at the maximum and not
at the last memorized light level .
www.conson.com
home and building automation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising