User`s Manual - icon service

User`s Manual - icon service
Model No. 831.488540
WARNING: To reduce
the risk of serious injury, read these
warnings before using the scooter.
1. Read and follow all instructions.
2. It is the owner’s responsibility to
ensure that all users of the scooter
are adequately informed of all
warnings and instructions.
3. Inspect the scooter and tighten or
replace any loose or missing parts
before each use. In addition, make
sure that the handles and the stem
are securely locked in position, the
wheels rotate freely, the brake is in
working order and free of all debris,
and the wheel bolts are secure.
4. The scooter should not be used by
children under the age of eight. A
responsible adult must always
supervise young riders.
5. Always wear protective equipment,
including a helmet, knee pads, wrist
guards, elbow pads, and closed-toed
shoes, when using the scooter.
6. Never ride on streets, roadways, or
driveways that enter vehicle traffic
routes. Never ride on wet or uneven
surfaces, at night, or when visibility
is poor.
7. Never tow a rider with a bicycle,
motorcycle, or vehicle.
8. Locate the warning decals on the
scooter, and read the warnings
before using the scooter.
9. Save this User’s Manual for future
reference.
10. This scooter should not be used by
persons weighing more than 200
pounds.
11. Braking from high speeds or prolonged braking on inclines can cause
excessive wear of the rear wheel and
brake. Exercise caution when selecting your area of use.
12. To prevent burns, avoid touching the
brake after prolonged use.
User’s Manual
Setup
1. Firmly press the thumb tab and pivot the upright up until it
locks in a nearly vertical position.
Hand
Brake
2. Insert the handles into the stem until the lock pins are visible in the holes in the stem.
3. Open the quick-release lever. Depress the lock pin on the
stem, and slide the stem up until the lock pin is visible in
one of the three holes in the upright. When the stem is at
the desired height, close the quick-release lever so it is snug
against the upright. If the quick release is not snug, see
ADJUSTING THE QUICK RELEASE on the back of this
manual.
Handle
Lock Pins
Stem
Front
Groove
Before using the scooter, make sure that the scooter is set up
as described and that all parts are securely tightened.
Quick Release
Lock Pin
The decal shown at the right has been placed on the scooter.
If the decal is missing or illegible, please call our Customer
Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time, to order
a free replacement decal. Apply the replacement decal in the
location shown.
Upright
Thumb Tab
Right Side
Left Side
Storage
1. Open the quick-release lever. Depress the lock pin on the
stem and slide the stem down into the upright. Close the
quick-release lever.
2. Depress the lock pins and remove the handles from the
stem. Press the handles into the storage clip on the upright.
Upright
Handle
Storage Clip
Thumb Tab
3. Pull the thumb tab and pivot the upright down until it locks
in the horizontal position.
Hand Brake and Cable are not shown.
Part List/Exploded Drawing Model No. 831.488540
R0101A
No.Qty. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
*
*
1
1
1
1
1
2
2
2
3
1
1
1
1
1
2
2
2
1
1
2
2
2
1
1
1
1
2
1
1
1
1
4
1
2
2
1
1
1
1
1
2
1
2
1
1
4
1
1
Deck
Head Tube
Fork
Upright
Stem
Handle
Foam Pad
Handle Cap
Lock Pin
Handle Cord
Quick Release
Upright Clamp w/Ring
Bearing Nut
Bearing Cap
Bearing
Bearing Race
Bushing
Pivot Union Bolt Set
Front Union Bolt Set
Rear Union Bolt Set
Wheel
Rear Wheel Spacer
Brake Spring
Brake
Head Tube Spring
Storage Clip
Front Wheel Spacer
Lock Pin
Deck Mount
Deck Cushion
Frame
Deck Screw
Cable Clip
Bracket Bolt
Brake Spacer
Mount Union Bolt Set
Hand Brake
Brake Bracket
Cable Bracket
Brake Cable
Flange Nut
Strap Clamp w/Ring
Bracket Nut
Upright Nut
Upright Bolt
Wheel Bearing
Carry Strap
User’s Manual
9
6
9
6
5
7
8
7
37
4
42
8
9
44
45
12
10
11
13
14
15
16
26
33
28
2
32
16
17
17
32
1
15
3
25
18
19
29
19 41
43
36
18
41
40
30
23
43
35 24
39
27
35
38
46
27 46
20
36
22
46
31
21
34
20
22 46
32 34
21
*The user’s manual and carry strap are not shown. Note: Specifications are subject to change without notice.
Ordering Replacement Parts
To order replacement parts, call toll-free 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding
holidays). When ordering parts, please mention the model number (831.488540) and the number and description of the parts needed.
Adjusting the Quick Release
If the quick release doesn’t hold the stem snug in place, you
will need to adjust it.
Open the quick-release lever. Turn the adjustment nut clockwise
one half turn while keeping the lever from turning. Close the
lever. Repeat this procedure until the stem is held snug in place.
Close
Quick
Release
Open
If the quick release is too snug to close, you will need to adjust it.
While the quick-release lever is open, turn the adjustment nut
counterclockwise one quarter turn while keeping the lever from
turning. Close the lever. Repeat this procedure until the stem is
held snug in place and the quick release is closed.
Lever
Adjustment
Nut
Hand Brake Maintenance
Refer to inset drawing 1. Locate the adjustment barrel (B) and
the lock nut (A) on the hand brake. Turn the lock nut (A) counterclockwise to loosen it. Next, turn the adjustment barrel (B)
counterclockwise a few turns. Then, turn the lock nut (2) clockwise to retighten it. Repeat until the hand brake is properly
adjusted.
1
A
B
If the movement of the hand brake needs to be further adjusted,
the lower end of the brake cable can be adjusted. Using an allen
wrench, remove the indicated union bolt set (36). Next, remove
the rear deck screw (32) and lift off the deck (1).
Refer to inset drawing 2. Locate the adjustment barrel (C) and
the lock nuts (D and E) near the end of the brake cable. Using a
small open-end wrench, turn the outer lock nut (E) counterclockwise to loosen it. Next, turn the adjustment barrel (C)
counterclockwise a few turns. Then, turn the inner lock nut (D)
clockwise to tighten it.
1
32
36
Reattach the deck (1) with the rear deck screw (32) and the
union bolt set (36).
36
C
2
D
E
Part No. 167662 R0101A
Printed in China © 2001 ICON Health & Fitness, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising