LYN VALVE/RV PA0002 - Engineered Silicone Products

LYN VALVE/RV PA0002 - Engineered Silicone Products
LYN VALVE/RV
PA0002 (AUTO) PA0300 (MANUAL)
esp
We’re thinking on a higher level.
Installation in Laminated Sockets
Instructions for use
1.
Determine valve location on cast model and flatten area with Sureform to insure dummy sits flush.
3.
Place reinforcing layers and second PVA bag over dummy. After mixing resin, place under vacuum to remove trapped air. Pour resin.
2.
4.
5.
6.
Place separation layer and first PVA bag over cast model. Use indelible marker in center of dummy hole to mark dummy location. Reinforce area of PVA
bag to prevent tearing. Use screw provided. After dummy has been screwed into cast ON TOP of PVA bag, press self-adhesive disc over screw.
Allow socket to cool. Using a disc sander, expose enough area to remove self-adhesive disc and screw. Continue sanding until the RED dummy face is
SLIGHTLY SCUFFED and socket material is flush with the dummy face. DO NOT OVER SAND.
BEFORE housing is inserted into socket, CHECK TO SEE that the factory installed black rubber “O” ring is still seated in the groove of the housing. Place
aluminum nut over valve housing and FIRMLY HAND TIGHTEN.
Insert valve and turn clockwise. GENTLY HAND TIGHTEN . The valve has an automatic STOP point. Do not attempt to turn valve after that stop point has
been reached NOTE: It may be helpful to first turn the valve counter clockwise and then clockwise to insure that threads are properly engaged.
Disassembly and Cleaning of the Lyn Valve/Rv
1.
2.
Rest valve insert on holder.
Using thumb, pres firmly (20-25lbs of pressure) on center of button.
-OR-
1.
Screw valve insert into housing ½ way.
3.
Turn valve over and push on center button to completely disassemble valve.
2.
Turn over, button side down onto table and press down with palm of hand
until “click” is heard.
The Auto-expulsion valve (PA0002) will come apart in five pieces, and the Manual valve (PA0300) into two pieces. Thoroughly wash with hot soapy water and
reassemble.
Reassembly of Lyn Valve/RV
To reassemble the Auto-expulsion valve, place rubber diaphragm with plastic side down into front part of valve insert-tap lightly to seat properly. Snap on back
part of valve insert. Turn valve face up and set spring in place. Place small plastic button over spring and turn over, button side down onto table. Press down
firmly until button snaps in place.
To reassemble the Manual valve, snap two parts together firmly until a “click” is heard.
Installation in Thermoplastic Material
1.
2.
3.
4.
5.
6.
7.
8.
Determine valve location on cast model and flatten area with Sureform to ensure dummy sits flush. Use indelible marker in center hole of dummy to mark the
cast.
Drill 1/8” pilot hole for dummy holding screw…AND…drill vacuum hole adjacent (1/2”) to the pilot hole using a long drill. Vacuum hole should extend to the
bottom of the cast model.
Mount dummy with small air holes in a vertical position over the pilot and vacuum holes. Use the screw provided. After dummy is in place, press
self-adhesive disc over screw.
Blister or drape mold thermoplastic socket. Guide plastic around dummy to ensure proper molding.
Allow plastic to cool. Using a disc sander, expose enough area to remove the self-adhesive disc and screw. Take cast to discsander and continue sanding
until the RED dummy face is SLIGHTLY SCUFFED and the plastic is flush to the dummy face. DO NOT OVER SAND.
Blow socket off cast model. NOTE: If you are planning to use th FlexConnect system, DO NOT REMOVE the socket from the cast at this time. See
FlexConnect Instructions.
BEFORE housing is inserted into socket, CHECK TO SEE that the factory installed black rubber “O” ring is still seated in the groove of the housing. Place
aluminum nut over valve housing and FIRMLY HAND TIGHTEN.
Insert valve and turn clockwise. GENTLY HAND TIGHTEN. The valve has an automatic STOP point. Do not attempt to turn valve after that stop point has
been reached. NOTE: It may be helpful to first turn the valve counter clockwise and then clockwise to in sure that threads are properly engaged.
Engineered Silicone Products, LLC
We’re thinking on a higher level.
75 Mill Street, Suite #2
Newton NJ, 07860
ph. 888-932-7377 / 973-300-5120
fax 973-300-5125
www.wearesp.com
Medidas
Zaagmolen 40
3962 GB Wijk bij Duurstede
Netherlands
medidas@medidas.nl
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising