High Power 976 nm Spectrum Stabilized Multi

High Power 976 nm Spectrum Stabilized Multi
Innovative Photonic Solutions
Innovative Photonic Solutions, Inc.
4250 U.S. Highway 1, Suite 1
Monmouth Junction, NJ 08852
Phone: (732) 355-9300
Fax (732) 355-9302
sales@innovativephotonics.com
http://www.innovativephotonics.com
Multi-Mode Fiber Coupled Turnkey M-Type
Features
•
•
•
•
•
•
•
•
Innovative Photonic Solution’s proprietary Wavelength
Stabilized Laser features high output power with narrow
spectral bandwidth. The laser’s stabilized peak wavelength
remains “locked” regardless of case temperature (10 to 35
deg. C).
Devices can be spectrally tailored to suit application needs
and offer side mode suppression ratios (SMSRs) better
than 40 dB, thereby providing extremely high signal to
noise ratio and making these sources ideal for Raman
spectroscopy and pump laser applications.
The laser is integrated with high performance laser drive
and temperature control electronics and integrated into a
fully turn-key UL/CE and IEC certified system with all safety
features.
In addition to benchtop functionality, the side panel can be
opened and the “guts” of the laser (the U-type engine
inside) can be removed so that a different wavelength can
“drop in,” or the U-type can be integrated as an OEM
component into a user system once testing is done.
Wavelength Stabilized Spectrum
High Power Multi-Mode Fiber Coupled Output
UL/CE and IEC Certified
Turn-Key Operation
Narrow Spectral Linewidth (< 0.15 FWHM)
Narrowed Spectral Linewidth available upon request
(< 0.07 nm FWHM). Add – NL to part number
Temperature Stabilized Spectrum (< 0.007 nm/0C)
40 dB SMSR Typical
Standard Wavelengths
•
•
•
•
647 nm
785 nm
808 nm
830 nm
•
1064 nm
Additional wavelengths available upon request
General Optical Specifications
Wavelength Tolerance
Spectral Linewidth (Dl)
Narrowed Linewidth (-NL)
Spectral Linewidth (Dl)
Wavelength Stability Range
SMSR
Output Power Stability
Peak Wavelength Drift
Modulation Rate
Warm-up time
+/- 0.5 nm
< 0.15 nm
< 0.07 nm
10 C - 35 C
35 -45 dB
1% typical
+/- 7pm assuming TEC control +/0.1 degree C
CW to 1KHz for 10% to 100%
power, 10kHz at 50% duty cycle
10 seconds from cold start
1.5 seconds from warm start
Physical Specifications
Optical Fiber
Connector
Module Dimensions
Module weight
Case Material
Operating Temperature
Environment
Storage Temperature
100-105/125 micron multimode fiber,
0.22 NA
FC/PC or SMA905
9.48 x 6.94 x 4.14 inches
48 ounces
Anodized Aluminmum
10 to 35 degrees C
0-80% Humidity, non condensing
-10 to + 55 degress C
Typical 785 nm Stabilized Laser Spectrum
All data and statements contained herein are subject to change in accordance with Innovative Photonic Solution’s policy of continual product improvement. No information
contained herein is intended for use in connection with any contract except as may be first confirmed in writing by Innovative Photonic Solutions. The publication of information in
this document does not imply freedom from patent or other rights of Innovative Photonic Solutions or others.
2.19.15 TG
Innovative Photonic Solutions
Innovative Photonic Solutions, Inc.
4250 U.S. Highway 1, Suite 1
Monmouth Junction, NJ 08852
Phone: (732) 355-9300
Fax (732) 355-9302
sales@innovativephotonics.com
http://www.innovativephotonics.com
Wavelength
(nm)
Min.
Power
(mW)
647
150
350
785
500
350
808
500
350
830
500
1064
500
Part Numbering Schema
Part Number1
Connector
I0647MM0150MF
I0647MM0150MS
I0785MM0350MF
I0785MM0350MS
I0785MM0500MF
I0785MM0500MS
I0808MM0350MF
I0808MM0350MS
I0808MM0500MF
I0808MM0500MS
I0830MM0350MF
I0830MM0350MS
I0830MM0500MF
I0830MM0500MS
I1064MM0500MF
I1064MM0500MS
FC/PC
SMA
FC/PC
SMA
FC/PC
SMA
FC/PC
SMA
FC/PC
SMA
FC/PC
SMA
FC/PC
SMA
FC/PC
SMA
Electrical Requirements
Input Power
Fuse Rating
100 – 240 VAC,
50 – 60 Hz, 0.4 A
250 V, 1 A, Fast Blow,
5 mm x 20 mm, 2 each
1 – For narrowed spectral linewidth <0.07 nm, add “-NL” to part
number
Operational Notes
1. Do not retro-reflect beam! This can cause Catastrophic Optical Damage
(COD) and is not covered under warranty.
2. Knob on front adjust power by adjusting drive current. LED readout is
in amperes.
3. IPS can supply our Laser Control Unit (LCU-M) for USB control. It comes
standard with pulse width modulation (PWM) software. Ask about this
product.
4. 100-105 micron core fiber is standard. 62.5 micron core fiber available
upon request but will affect output power. Please ask for part number.
5. Add “–NL” to standard part number for narrowed spectral linewidth
<0.07 nm.
6. See Operation Manual for full operating and safety instructions. This
document is meant to offer a product overview.
Mechanical Specifications
Front View
Back
Bottom View
Side View
All data and statements contained herein are subject to change in accordance with Innovative Photonic Solution’s policy of continual product improvement. No information
contained herein is intended for use in connection with any contract except as may be first confirmed in writing by Innovative Photonic Solutions. The publication of information in
this document does not imply freedom from patent or other rights of Innovative Photonic Solutions or others.
2.19.15 TG
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising