Speed Dome Camera Controller Operation Manual

Speed Dome Camera Controller Operation Manual
VOOK
PROFESSIONAL MONITORING
Speed Dome Camera Controller
Operation Manual
VSK-100
VOOK
I.
PROFESSIONAL MONITORING
Brief introduction
The keyboard controller is used for terminal receivers such as the intelligent Speed Dome and the decoder etc.
Taking the EIA/RS-485 electrical interface between the keyboard and the receiver, one keyboard can control as
much as 32 speed dome and decoders without driving the bus and the maximum communication distance between
the keyboard and the receiver is up to 1.2 km. It’s very easy for operating and setting the Speed Dome Camera.
The controller is also to control the terminal receiver to achieve the function of controlling pan/tilt, lens and ect.
Main Functions:
‹
‹
‹
‹
‹
‹
Set the address range of the dome camera and the decoder:0~255.
Control all functions of the dome camera such as Power ON/OFF.
To operate the pan/tilt of Speed Dome Camera moving in different speed lever
Set or call the set points and cruise tracks of the dome camera. Altogether 128 preset points and 6 cruise
tracks can be set. Each track involves 16 preset position and the dwelling time and call speed upon each
point can be set as well.
Manually or automatically control the dome camera, and change the leaving settings of particular camera
by call the menu of the camera. .
Manually control the focus, zoom and iris of the camera.
II. Introduction of Functions:
Select Camera(0~255)
Joystick Control
Lens Control
Control pan/tilt direction and speed of the holder.
Control the focus, zoom and iris of the camera
Operation of Preset Position (1~128)
Set Preset Position
Call Preset Position
Operation of Cruise Track(1~6)
Set Cruise Track
Run Cruise Track
Automatic Horizontal Scan Control of dome
(including speed and direction of scan)
Self-Learning Track of Intelligent Speed Dome
Function Setting of Menu of Speed Dome
Control of Multiplexer
Direct Control on Decoder
Control front devices such as the decoder etc.
III. Introduction of the keyboard Panel
1. The Sketch of the Front Panel and Description of Buttons (Figure 1)
VOOK
PROFESSIONAL MONITORING
There are speed joystick, buttons and LCD on the front panel of the control keyboard. The display is used to show
the status of the system as well as operation information. The joystick controls the upward, downward, leftward
and right ward speed motion of the speed dome. The description of buttons is as follows:
(Figure 1)
z
Func(1 cam):Set special function of the system together with other buttons.
z
Zoom(Full screen)
:Show picture of the camera in full screen.
z
PIP(up arrow):Show picture of the camera in PIP mode (Picture-in-Picture).
z
2×2(down arrow):Show picture of the camera in 4-frame.
z
3×3(left arrow):Show picture of the camera in 9-frame.
z
4×4(right arrow):Show picture of the camera in 16-frame.
z
Live:Show live picture of the camera at current mode.
z
Tape:Playback pictures; Function + Tape: Playback video information of VCR.
z
CAM: Select address of the intelligent Speed Dome or multiplexer.
z
CALL:
z
PRESET:To set the preset position.
z
SHOT: To set up or call cruising track.
z
TIME: Set time for special function.
z
AUTO:To control auto-horizontal rotation for pan/tilt.
z
WIDE:To a wide angle.
z
TELE:To turn to a telescopic range.
z
FAR:To make focus far manually.
z
NEAR:To make focus near manually.
z
OPEN:To open iris.
z
CLOSE:To close iris.
z
ON:Switch on the setting of function.
z
OFF:Switch off the setting of function.
z
F1/F2:Auxiliary control buttons.
z
F3:Switching control between intelligent Speed Dome and Multiplexer.
To call the preset position.
VOOK
PROFESSIONAL MONITORING
z
0-9: Number key
z
CLEAR:To clear inputted data
z
ENTER:To confirm
2. Rear Panel (Figure 2)
(Figure 2)
A. Power input connector: input DC12V power.
B. ID-Code switch: Used to set the protocol in use and the baud rate of communications.
C. Communication connector RS485: The controller is connected to adapter box by specific cable.
IV.
Setting of the Keyboard
a) The protocol in use and the baud rate of communication of the keyboard are set by the
ID-Code in Figure 2. DIP1-DIP4 are used to select type of the communication protocol as
per following table (●means the protocol is available):
Normal Baud
Rate
Selection of Protocols
Type of Protocols
Integrated
Protocol
DIP1
DIP2
DIP3
DIP4
DIP5
DIP6
Minking-VOOK A01
OFF
OFF
OFF
OFF
ON
OFF
●
Minking-VOOK B01
ON
OFF
OFF
OFF
OFF
ON
●
Santachi
OFF
ON
OFF
OFF
OFF
ON
●
PELCO-D
ON
ON
OFF
OFF
OFF
OFF
●
OFF
OFF
ON
OFF
ON
OFF
●
OFF
ON
●
PANASONIC
ON
OFF
ON
OFF
OFF
ON
●
Longcomity
OFF
ON
ON
OFF
OFF
ON
〇
HUNDA600
ON
ON
ON
OFF
OFF
ON
●
LILIN
OFF
OFF
OFF
ON
OFF
ON
●
VICON
ON
OFF
OFF
ON
ON
OFF
●
MOLYNX
OFF
ON
OFF
ON
OFF
ON
〇
KALATEL
ON
ON
OFF
ON
ON
OFF
●
VCL
OFF
OFF
ON
ON
OFF
ON
〇
Reserved
ON
OFF
ON
ON
OFF
ON
〇
ALEC
OFF
ON
ON
ON
OFF
ON
●
Ultrak
ON
ON
ON
ON
OFF
ON
●
PELCO-P/4800Bps
PELCO-P/9600Bps
b) DIP5 and DIP6 are used to select the baud rate, shown as following table(DIP7 and DIP8
are not used):
VOOK
PROFESSIONAL MONITORING
Status of ID-Code
DIP5
DIP6
2400bps
OFF
OFF
4800bps
ON
OFF
9600bps
OFF
ON
19200bps
ON
ON
Baud Rate
c)
DIP1
DIP2
DIP4
DIP7
DIP8
Some of the ID-Code of the protocols are set as follows:
Mi nKi ng B01/ 9600Bps
Mi nKi ng A01/ 4800Bps
PELCO- D/ 2400Bps
PELCO- P/ 4800Bps
PELCO- P/ 9600Bps
PANASONI C/ 9600Bps
Ul t r ak/ 9600Bps
d)
DIP3
ON 1 2 3 4 5 6 7 8
ON 1 2 3 4 5 6 7 8
ON 1 2 3 4 5 6 7 8
ON 1 2 3 4 5 6 7 8
ON 1 2 3 4 5 6 7 8
ON 1 2 3 4 5 6 7 8
ON 1 2 3 4 5 6 7 8
Switching control between intelligent decoder and multiplexer.:The keyboard can be operated
in two modes: Intelligent Decoder and Multiplexer. When power supply is on it is operated on the
default mode of Intelligent Decoder. Press [F3] down until the LCD disply“CONTROLLING MULX” ,
then control the processor by the RS-232 output of the keyboard. Attention! If the LCD is not the right
state, the Multiplexer can not be under of control.
V.
Operation of the Keyboard
1.
Select Address of Speed Dome Camera /Decoder:[CAM]+[N]+[Enter]
Display: Current CamID:001
Description:N –– No. of camera from 0 to 255
Function:Select the address of the camera to be controlled. When the value N is in conformity with the
address of the speed dome, it will be under control.
2. To set preset position:[PRESET]+[N]+[ Enter]
Display:Preset No:001
Description:N –– No. of preset position from 1 to 128.
Function:Store current position and refer it as No. N position.
VOOK
3.
PROFESSIONAL MONITORING
Call the Preset position:[CALL]+[N]+[ Enter]
Display:Call Number:001
Description::N –– No. of preset position from 1 to 128.
Function: Transfer the camera to the position of No. N preset position.
4. Cancel the Preset position:[PRESET]+[N]+[OFF]
Display:Preset No:001
Description:N –– No. of preset position from 1 to 128.
Function:Delete the No. N Preset position stored.
5. Set the cruise track (Minking A01/B01、PELCO-P、PELCO-D、ALEC、Ultrak Available)
z Enter the status of track setting:[SHOT]+[N]+ [ON] (N:No. of track from 1 to 6).
Display:Track = 01
Sum = 06
Description:Track No1 is currently set, in which there are 6 preset points.
z Edit Track:Press [TELE] to edit afterward and press [WIDE] to edit return. Each track involves 16
preset points and the running speed and the dwelling time of each preset position.
Display:No.:01
Point:001 → Description:The 1st preset position in the track is 01.
Display:No.:01
Speed:001 → Description:The speed of the 1st preset point in the track is
the 1st class.
Display:No.:01
Time: 004 → Description:The dwelling time of the 1st preset point in the
track is 4 seconds
z Speed Range:1 to 8 from the fastest to the lowest. Any speed outside the range well be referred as
the 1st class; the range of the dwelling time is:1 to 99.
z When the No. N preset point is set as No. 0, then all preset points before the No. N preset point in
the track will be valid however all numbers of preset points afterward and their speed and dwelling
time shall be set as 0 automatically.
z After tracks are edited, press OFF to store and exit while push the joystick to exit without storage.
6. Tour the Track:[SHOT]+[N]+ [Enter]
Display:Input Tour No:01
Description:N –– No. of the track from 1 to 6.
Function:Tour the No. N track and stop tour by pushing the joystick.
7. Stop the Track: [SHOT]+[N]+ [OFF]
Display:Input Tour No:01
Description:N –– No. of the track from 1 to 6.
Function:Stop the No. N track or stop tour by pushing the joystick.
8. Cancel Cruise Track: [SHOT]+[N]+ [OFF] (Pressing [OFF] down until “ Clear Tour OK ”appears)
Display:Input Tour No:01
Description:N –– No. of the track from 1 to 6.
Function:Delete the No. N track
9. To turn on Auto Pan (Operation of NEON、SAMSUNG Protocol):[AUTO]+[P1]+[ON]+[P2]+[OFF]
Display:Input 1st No:001
Description:P1 –– the starting scan No. of preset point from 1 to 128, which should be set already.
Display:Input 2nd No:002
Description:P2 – the ending scan No. of preset point from 1 to 128, which should be set already. If P1 =
P2 or P1 and P2 are coincided, the speed dome will make scan in range of 360°.
Note:① For PELCO-D、PELCO-P Protocol the way of operation is as follows:
‹ Set the starting scan position: Transfer the Speed Dome to the starting scan position, operation
[AUTO]+[ON]
VOOK
PROFESSIONAL MONITORING
Set the ending scan position: Transfer the Speed Dome to the ending scan position,operation
[AUTO]+[OFF]
‹ Run Auto Pan:[AUTO]+[ENTER]
②Auto Pan operation takes the following parameters. You must set these parameters before using a
‹
Auto Pan command to begin the scan operation. You can use the scan stop command ot PT scan stop
command to stop the scan. Setting scan condition.
z Auto Pan Position(First specify position, second specify position)
z Auto Pan Speed and Direction
10. Stop Auto Pan:[AUTO]+[OFF]( Only Minking A01、B01 Available) or push the joystick to stop scan
11. Control the zoom of the Camera:[WIDE]/[TELE]
12. Control the Focus of the Camera:[FAR]/[NEAR]
13. Control the Iris of the Camera:[OPEN]/[CLOSE]
14. Auxiliary Control of the Camera:By combination of [F1] and [ON], [OFF] buttons, you can set some
data of the camera, and functions are listed as follows(operations of NEON Protocol):
No. of
Value N
Control Object
Definition of Keyboard Operation
[F1]+N+[ON]
[F1]+N+[OFF]
Power ON/OFF
Switching
Recover Initial
Values of Camera
0
Camera power supply/reset control
1
Back Light Compensation
ON
OFF
2
Zero Illumination (refer to function of
camera)
ON
OFF
3
Menu/Display (refer to function of
camera)
ON
OFF
4
Digital Zoom
ON
OFF
5
Back Light of Keyboard Screen
ON
OFF
6
Focus
Automatic
Manual
7
Iris
Automatic
Manual
Automatic
Manual
Indoor Mode
Outdoor Mode
ATW Mode
One Push WB
Color
Black & White
< 180°, low speed
> 180°, low speed
8
9
White Balance Mode(WB)
10
11
Black & White/Color Switching
12
14
Set Auto Pan (Only conditions for scan. If
start scan, operate as Item 6 in this
paragraph)
15
Reserved
16
Reserved
17
Reserved
18
Reserved
13
z
z
z
< 180°, middle speed > 180°, middle speed
< 180°, high speed
> 180°, high speed
For different camera, control functions in the list could be different.
For the camera with the menu, switch ON/OFF the menu by “[F1]+[3]+[ON]”, and switch
ON/OFF the OSD by “[F1]+[3]+[OFF]”. In case the camera has the menu and the menu is ON:
1. Select the item on the menu by buttons [WIDE]/[TELE] to scroll the cursor up or down;
2. Chang the status of the selected item on the menu by buttons [FAR]/[NEAR];
3. Switch OFF the menu as per operations in the list after the menu is set.
Take care of differences between the Menu of Speed Dome and the Menu of Camera. For the
speed dome with the menu, enter the menu by “[CALL]+[64]+[Enter]” and basic operations are
VOOK
PROFESSIONAL MONITORING
as follows:
1. Call No.64 preset point to open the main menu by the control keyboard.
2. When the menu appears on the screen, move the cursor to the item you need to set by “TILT
UP” and “TILT DOWN”, and enter the
settings of the item to make change by “PAN
LEFT” and “PAN RIGHT”;
3. Speed up operation of the joystick after
keeping it for one second in one direction.
右
4. All settings of the menu could not be lost
上
even power failure occurred;
5. Operations under special case can be referred
下
on the description of the menu of the ball
machine.
15. Use the Joystick to Control the Speed Dome Camera:
Figure3
You can use the speed joystick to control the Pan/Tilt
direction and speed of the dome of the camera randomly.
The speed of pan/tilt is decided by the angle of the joystick you operated (Figure 3). Change the tilting
angle of the joystick you can adjust the speed evenly and the camera can be focused automatically in the
course of scan to keep images being distinct.
16. In case error operation occurs, normal display will be recovered after “Error Operation” appears for 1
second.
上
左
右
下
低速度
高速度
VI.
Installation and Connection:
Attention: Please read the operation manual of the keyboard and the speed
dome carefully before connecting wires. Any incorrect connections can cause
permanent damage of the device. When connecting wires, first switch off the
power supply of all devices. The communication wires between devices should
be shielded twisted cable. When installing cables they should be far away from
high voltage lines or other possible interference circuits as can as possible.
1. The marking of wires of the transfer box(Figure 4)
2. Connections of the keyboard controller controlling multiple speed dome
cameras(figure5)
RED
BLACK
GREEN
YELLOW
REDŁşRS485+
BLACKŁşRS485GREENŁşGND
YELLOWŁşRS232 OUT
Figure 4
ALM
1
ALM
2
3
DC IN
GND
4
R+
5
R6
VIDEO7
VIDEO+
8
DOME SPEED 1
ALM
1
ALM
2
3
DC IN
GND
4
R+
5
R6
VIDEO7
VIDEO+
8
DOME SPEED N
Figure6
Figure5
左
VOOK
PROFESSIONAL MONITORING
3. Connections between the keyboard and the speed dome camera(Figure6)
4. The keyboard controls the Multiplexer directly(Figure7)
Figure7
VII.
‹
‹
‹
‹
‹
‹
‹
‹
Technical Specifications:
Communication between Speed Dome Camera and Controller:Port to multi-port and half duplex
function.
Communication connector: RS-485.
Baud Rate of Communication:Four baud rates i.e. 2400Bps, 4800Bps, 9600Bps and 19200Bps.
Distance of Communication:1200 M in maximum
Power Supply:DC12V/800 mA
Size: 380 × 165 × 80(mm)
Weight:2 Kg
Number of Controlled Speed Dome Camera up to 32.
VIII. Points for Attention:
‹
‹
‹
‹
‹
‹
Please read the operation manual of the keyboard carefully before using it.
The operation manual is mainly focused on all functions of B01 Protocol. For other different
protocols, operations could be something difference and those different parts will be listed on
“Supplementary Description of the Keyboard Controller” in details.
The keyboard takes 12V DC power supply. Please confirm the voltage and polarity before the power
supply is switched on.
Do not place the keyboard under the rain or on wet place so as to avoid short circuit or electrical shock.
As the keyboard is a sophisticated electronic device, you should never open the case so as to avoid the
occurrence of trouble.
The keyboard has integrated multiple protocols, and you are pleased to select correct protocol and the
baud rate. When switching on power supply, take care of the selected protocol and the baud rate on the
first screen.
VOOK
‹
‹
‹
PROFESSIONAL MONITORING
In case the keyboard controls the Multiplexer, the operation of combination buttons is as follows:
Press one button first, and press the other button after release the first one.
For example:When enter/exit setting of the menu (Function + Zoom), press Function button first, and
press Zoom button after Function button is released.
In case the keyboard controls the multiplexer, the operation of combination buttons is as follows:
Press one button first,and press the other button after release the first one. While use Function alone,
please put it down, until“Motion Detect OK”appears.
When the keyboard controls the Multiplexer, please refer to concerned operation manual of Multiplexer
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising