TRU-SINE MPS Series

TRU-SINE MPS Series
project:
fixture type:
location:
contact/phone:
TRU-SINE MPS Series
PURE SINE WAVE 8/75$MICRO INVERTERS 20-55 WATTS
Pure Sine Wave
micro inverter systems for powering e ee
d 55 Watts of incandescent, fluorescent or LED lighting loads. Pulse
width modulated (PWM) output design provides clean, 60 Hz. sinusoidal
emergency power to lighting loads. Models are available for surface,
recessed or T-Grid mounting as required. MPS models support normallyon, normally-off or switched operation.
product features
•
•
•
•
•
•
•
•
•
Powers LED, incandescent and fluorescent fixtures
True sinusoidal AC PWM design provides clean emergency output
Universal 120/277VAC, 60Hz. input/output
Unit capacities from 20 to 55 watts
Soft Start design reduces fixture inrush current
Install up to 1000 feet from controlled fixture(s)
Surface, recessed or T-Grid mount models
Lumen output from fixture is 100% of nominal
Unique design eliminates compatibility problems with LED drivers and
fluorescent ballasts
• oes o eed o e de ed o
• Normally-on and/or Normally-off load output
• Provisions for local switching capability - Always on during emergency
conditions regardless of local switch position
• Temperature compendated, dual-mode charger
• Low voltage disconnect provides protection against battery deep discharge
• Maintenance-free lead-calcium and nickel-cadmium batteries offered
• Control panel with momentary test switch
• AC-On, Charge-On and Inverter-On LED indicators
• Fuse protection, Reverse battery and AC lockout protection
• Meets NFPA Life Safety Code 101, OSHA, NEC, State and local Codes
• 90 Minute Runtime Minimum
• UL 924 listed
Surface Mount Housing
Recessed Mount Housing
T-Grid Mount Housing
dimensions
Standard Surface Mount
3 1/8" (MPS-20/32)
4 3/8" (MPS-35/55)
Optional Recessed Mount Housing
3 1/8" (MPS-20/32)
Optional Ceiling T-Grid Mount Housing
4 3/8" (MPS-35/55)
16 1/4"
14 3/4"
8 7/8"
8 7/8"
7 3/8
ordering
orderinginformation
information
model #
MPS-20
MPS-32
MPS-35
MPS-55
watts/va rating*
32 W/VA
35 W/VA
55 W/VA
options description
Lead-Calcium
Nickel-Cadmium
Lead-Calcium
Surface Mount Housing (standard)
Rescessed Mount Housing
Plenum Rated Ceiling T-Grid Mount
Custom Housing Color
Ordering Example: MPS-20-SF
*capacity for 90 minutes
Mule Lighting , Inc.
46 Baker Street Providence, RI 02905
800 556-7690 P
401 941-2929 F
www.mulelighting.com
project:
fixture type:
location:
contact/phone:
TRU-SINE MPS Series
PURE SINE WAVE ULTRA-MICRO INVERTERS 20-55 WATTS
application
wiring
The MPS Series is designed to provide up to 20 TO 55 watts of emergency power to LED, Fluorescent and/or incandescent light fixtures. The
MPS unit provides clean, sinusoidal AC output power allowing it to be
remotely mounted up to 1000 feet away from the controlled fixture(s).
Unlike a fluorescent emergency ballast, the MPS provides power to the
input side of the fixture (including the ballast) eliminating any chance of
incompatibility. The MPS Series is is available for surface, recessed or
ceiling T-Grid mounting as required. All MPS systems will provide
emergency power output for a minimum of 90 minutes.
Connection to an unswitched AC circuit is required by the NEC.
Wiring access is provided for by conduit knockouts in the unit
housing. MPS Series models also provide knockouts in the back
of the housing for rear wiring from standard electrical boxes
when surface mounting.
load compatibility
MPS model's clean, sinusoidal AC output will operate incandescent lamps as well as all common fluorescent and LED lamp
types. Lighting loads are driven at 100% output for the entire
emergency power cycle. This outstanding feature translates into
greater occupant egress vision and safety.
construction
The MPS Series housing is constructed of heavy duty steel cabinet that is
finished with a white baked-on powder paint providing scratch and
corrosion resistance. Optional color finishes are available, consult factory.
code compliance
All models are UL924 Listed and meet NFPA 101 Life Safety
Code, NEC, OSHA, Local and State Codes. Optional T-Grid
models are plenum rated.
mounting
SURFACE MOUNT: (STANDARD MODELS)
operation
Surface mount models are designed for mounting to walls by means of
keyhole slots provided in the rear of the unit housing.
Upon failure of the normal utility power the MPS unit is automatically turned on by a solid-state switching circuit and
provides a minimum of 90 minutes of emergency power to the
connected load. Lumen output will be maintained at 100% of the
lamps rating throughout the entire duration. A solid-state low
voltage disconnect circuit is used to protect the battery from
being severely damaged by a deep discharge. When normal
utility power is restored, the unit switches the load back to
normal utility operation and the fully automatic, temperature
compensated, dual mode charger begins to restore the battery;
bringing it to full charge within UL924 specified parameters. A
brownout sensing circuit insures proper operation during 'low
line" conditions.
RECESSED MOUNT:
Recessed models provide a trim flange and recessed mounting holes on
both sides of the enclosure.
T-GRID MOUNT:
The housing design allows for simple drop-in installation between
standard T-Grid runs. Safety wires (supplied by others) are required for
attachment to building structure.
general specifications
System
Model
Number
MPS-32
MPS-55
MPS-20
MPS-35
Housing
Size
Small
Large
Small
Large
Input/Output Capacity
Voltage
(90 Min)
(60Hz.)
Watts/VA
120/277
120/277
120/277
120/277
Mule Lighting , Inc.
32/32
55/55
20/20
35/35
Battery
Type
Lead-Calc.
Lead-Calc.
NiCad
NiCad
Power
Battery DC Input
Input Current
Consum. Voltage Current 120VAC 277VAC
(Max.) (Max.)
(Max.)
(Vdc)
(Adc)
9W
9W
9W
9W
46 Baker Street Providence, RI 02905
12
12
12
12
3.4
5.7
2.1
3.8
0.34A
0.54A
0.25A
0.37A
800 556-7690 P
0.15A
0.23A
0.11A
0.16A
Thermal Output In
BTUs
Standby
Emerg.
Temp.
Range
(ºC)
7
7
31
31
32
47
22
35
20 to 30
20 to 30
0 to 50
0 to 50
401 941-2929 F
System
Weights
Lbs. Kg.
14
18
11
12
6.4
8.2
5.0
5.4
www.mulelighting.com
project:
fixture type:
location:
contact/phone:
TRU-SINE MPS Series
PURE SINE WAVE ULTRA-MICRO INVERTERS 20-55 WATTS
electrical
batteries & charger
Input
Battery
Input Voltages: (60Hz) 120 or 277VAC ± 10%
Battery: Lead Calcium (10 year life) or Ni-Cad (15 year life)
Input Frequencies: 60Hz ± 2%
Battery Voltage: 12VDC for all models
Input Protection: Provided by Service Panel, Rated 20A Max
Runtime: 90 minutes standard - based on battery performance at 77ºF (25ºC).
Output
Other runtimes available, consult factory.
Output Voltages: (60Hz) 120 or 277VAC
Efficiency Rating: 98% at full rated load (line)
Waveform: Sinusoidal (digitally controlled)
Static Voltage: ± 5% during battery discharge. 0-100% linear load.
Battery Protection: Low Voltage Battery Disconnect protects
the battery from being severely damaged by deep discharge
during prolonged power failures.
DC Overload and Short Circuit Protection provided by a DC input
breaker and fuse.
Output Frequencies: 60 Hz. ± 0.3Hz during emergency cycle
Charger
Output Distortion: Less than 3% THD (linear load)
Charger Type: Fully automatic, temperature compensated,
Transfer Time: Less than 1.0 second
dual-mode charger
Load Power Factor Range: 0.44 Lead to 0.44 Lag
Power Consumption (Charger Only):
Minimum Loading: 0% of rated system capacity
9W maximum (2.5W in standby)
Output Protection: Inverter fuse
Recharge Duty Cycle: Meets UL924 requirements
Controls: Momentary test switch, AC-On, Charge-On and
Inverter-On LED indicator lights
improved aesthetics
The MPS system’s sinusoidal AC output design eliminates voltage
drop and proximity concerns. This allows added flexibility in
installation location as MPS units can be installed hundreds of
feet from the units they power. This means MPS units can be
located conveniently out of sight in closets or utility rooms
without interrupting architectural aesthetics. In lighting
applications, no special or additional emergency fixtures are
necessary. Simply designate and connect existing lighting
fixtures, either interior or exterior, to the MPS unit for emergency operation eliminating the need for exposed, stand-alone
emergency luminaires.
warranty
Environmental
Altitude: < 10,000 feet (3,000m) above sea level without
derating.
Operating Temperature Range:
Lead-Calcium Models: 68ºF to 86ºF (20ºC to 30ºC)
Ni-Cad Models: 32ºF to 122ºF (0ºC to 50ºC)
NOTE: Optimum system performance between 20°C (68°F) and
30°C (86°F); temperatures outside of this range will affect
battery performance and life.
Relative Humidity: 95% non-condensing
Unit: 3-years full coverage against defects in materials and
workmanship from date of shipment
Lead-Calcium Battery: 3 years full warranty plus an
additional 7 years of pro-rata coverage
Nickel-Cadmium Battery: 5 years full warranty plus
an additional 7 years of pro-rata coverage
Mule Lighting , Inc.
Safety Circuitry: AC Lockout prevents battery discharge
prior to initial unit power-up. Brownout Protection
automatically switches the unit to emer-gency mode when
utility voltage is significantly reduced.
46 Baker Street Providence, RI 02905
SYSTEM STATUS MONITORING PANEL
All MPS systems provide a monitoring panel on the front of the
unit to show operating status at all times. The panel provides a
test switch for user initiated system tests and a 3-LED array that
provides an intuitive visual indication of unit readiness.
800 556-7690 P
401 941-2929 F
www.mulelighting.com
project:
fixture type:
location:
contact/phone:
TRU-SINE MPS Series
PURE SINE WAVE ULTRA-MICRO INVERTERS 20-55 WATTS
AC INPUT CONNECTION DIAGRAM
WIRING DIAGRAMS
Diagram 1.
Diagram 2.
Diagram 3.
Diagram 4.
NOTES:
SUGGESTED SPECIFICATION
An inverter system with sinusoidal output shall be supplied capable of powering any combination of lighting fixtures, including incandescent, fluorescent, induction and/or LED light
sources without compatibility problems. The system shall transfer in less than 1.0 second to reliably back up lighting fixtures without loss of illumination and operate any and all
connected lighting fixtures at full lumen output during the complete 90 minute discharge cycle.The input voltage shall be the same as the output voltage and shall be single phase
(120) (277) volts, 60 Hz. Capacity will be (20 Watts) (32 Watts) (35 Watts)(55 Watts) for a minimum duration of 90 minutes. The design shall be a standby, off-line inverter with on
line efficiency of 98%; on-line double conversion UPS systems shall not be considered acceptable alternatives. MPS system output shall be a PWM generated sine wave with less than
3% total harmonic distortion. The system shall also provide short circuit and overload protection as standard. An intuitive three LED display shall provide system operational
information at a glance and alert user to any malfunction in system performance. Authorized maintenance personnel shall have access to the system’s controls while being protected
from any live exposed connections. Protective devices shall include a DC input fuse. AC input overcurrent protection for live circuits to be provided by service panel rated 20A
maximum. AC lockout, reverse battery connection, low voltage battery disconnect (LVD), short circuit and overload protection shall be provided standard on all models. The entire
MPS system, including batteries, shall be provided in compact cabinetry which shall have provisions for (surface)(recessed)(T-Grid) mounting. System shall utilize a (sealed lead
calcium battery with a 10 year design life)(sealed Nickel-Cadmium battery with a 15 year design life). The charger shall be temperature compensated, dual mode type, and recharge
the batteries as per UL 924 guidelines. Entire system shall tested, approved, and labeled to UL924 Emergency Lighting and Power Systems standards. (T-Grid models will be plenum
rated).System shall be Mule Lighting, Inc. MPS series model number: _____________________________________________.
Mule Lighting , Inc.
46 Baker Street Providence, RI 02905
800 556-7690 P
401 941-2929 F
www.mulelighting.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising