liebert® nxl™, 250-400kva, single-module systems

liebert® nxl™, 250-400kva, single-module systems
LIEBERT® NXL™, 250-400KVA, SINGLE-MODULE SYSTEMS - SITE PLANNING DATA
Maintenance Bypass Panel (Option)
MBB
2
MIB
3
5
AC Output
To load
UPS Module
4
5
3
Bypass
AC input
4
5
BFB
1
Rectifier
AC input
DC Bus
CB1
Battery
System
6
CB2
6
MBD
Notes for Table 1
1.
2.
3.
4.
5.
Nominal rectifier AC input current (considered continuous) is based on full 6.
rated output load. Maximum current includes nominal input current and
maximum battery recharge current (considered noncontinuous). Continuous
and noncontinuous current limits are defined in NEC 100. Maximum input 7.
current is controlled by current limit setting which is adjustable. Values
shown for maximum setting are 125% of nominal input current.
Nominal AC output current (considered continuous) is based on full rated
8.
output load. Maximum current includes nominal output current and
overload current for 10 minutes.
Bypass AC input current (considered continuous) is based on full rated
output load.
9.
Feeder protection (by others in external equipment) for rectifier AC input
and bypass AC input is recommended to be provided by separate overcurrent 10.
protection devices.
11.
UPS output load cables must be run in separate conduit from input cables.
12.
Power cable from module DC bus to battery should be sized for a total
maximum 2.0 volt line drop (power cable drop plus return cable drop as
measured at the module) at maximum discharge current.
Grounding conductors to be sized per NEC 250-95. Neutral conductors to be
sized for full capacity—per NEC 310-16, Note 10—for systems with 4-wire
loads and half capacity for systems with 3-wire loads.
Rectifier AC Input: 3-phase, 3-wire, plus ground
AC Output to Load: 3-phase, 3- or 4-wire, plus ground
Bypass AC Input: 3-phase, 3- or 4-wire, plus ground
Module DC Input from Battery: 2-wire (positive and negative), plus ground
All wiring is to be in accordance with National and Local Electrical Codes.
Minimum overhead clearance is 2 ft. (0.6m) above the UPS.
Top or bottom cable entry through removable access plates. Cut plate to suit
conduit size.
Control wiring and power cables must be run in separate conduits. Control
wiring must be stranded tinned conductors.
13. 10% maximum reflected input harmonic current and 0.92 lagging input
power factor at full load.
1
Liebert® NXL™, 250-400kVA, Single-Module Systems - Site Planning Data
Table 1
UPS
Rating
Site planning data—480V input
AC
Output
Voltage
Rectifier AC
Input Current
Inverter or Bypass
AC Output Current
Max.
Battery
Current
at End of
Discharge (A)
Max.
Heat
Dissipation
Full Load
BTU/h (kWh)
Dimensions
Approx.
Weight
Unpacked
Floor Loading
Concentrated
Loading
WxDxH: in.
(mm)
lb. (kg)
lb./ft.2 (kg/m2)
kVA
kW
VAC
Input
Filter
Input
Xformer
Nom
Max
Nom
Max
Required
Battery
Disconnect
Rating (A)
250
225
480
Standard
NO
313
392
301
376
700
615
49,887 (14.6)
71.8x33.5x76.8
(1823x850x1950)
3965 (1798)
237 (1160)
300
270
480
Standard
NO
376
469
361
451
800
737
58,819 (17.2)
78.5x33.5x76.8
(1993x850x1950)
4690 (2127)
257 (1256)
400
360
480
Standard
NO
500
625
481
601
1000
981
75,676 (22.2)
78.5x39.4x76.8
(1993x1000x1950)
5250 (2381)
244 (1195)
13
—
6
6,8,9,11,12
—
—
—
—
See Notes (p. 1):
Options
1,4,5,7,8,9,11,12
2,3,5,7,8,9,11,12
© 2008 Liebert Corporation
Technical Support / Service
United States
All rights reserved throughout the world. Specifications subject to change without notice.
1050
Dearborn Drive
800-543-2378
® Liebert is a registered trademark of Liebert Corporation.
All names referred to are trademarks or registered trademarks of their respective owners. powertech@emersonnetworkpower.com P.O. Box 29186
Web site: www.liebert.com
SL-25510_REV0_03-08
2
Columbus, OH 43229
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising