LOW VOLTAGE AC/DC POWER SUPPLY

LOW VOLTAGE AC/DC POWER SUPPLY
012-06263A
Instruction Manual
for the PASCO scientific
Model SF-9584A
10/96
LOW VOLTAGE AC/DC
POWER SUPPLY
LOW VOLTAGE AC/DC POWER SUPPLY
¨
V
A
10
VOLTAGE ADJUST
DC
+
–
0 – 24 V
12 14
8
16
18
6
20
CURRENT ADJUST
MAX DC CURRRENT
10 A
4
6A
12 V
24 V
OFF
AC
SF-9584A
2 24
ON
22
RESET
2-24 V
6 A MAX
© 1996 PASCO scientific
$5.00
̈
better
10101 Foothills Blvd. • P.O. Box 619011 • Roseville, CA 95678-9011 USA
Phone (916) 786-3800 • FAX (916) 786-8905 • email: techsupp@PASCO.com
ways to
teach science
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER ON UNIT. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead, within
an equilateral triangle, is intended to alert
the user of the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an equilateral triangle is intended to alert the user
of the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the
appliance.
012-06263A
Low Voltage AC/DC Power Supply
Table of Contents
Section
Page
Copyright, Warranty, and Equipment Return ...................................................... ii
Introduction ....................................................................................................... 1
Operation ....................................................................................................... 1 - 2
Equipment Specifications ................................................................................... 3
Schematics and Parts Lists ............................................................................. 5 - 12
Technical Support ................................................................................... Back Cover
i
Low Voltage AC/DC Power Supply
012-06263A
Copyright, Warranty and Equipment Return
Please—Feel free to duplicate this manual
subject to the copyright restrictions below.
Copyright Notice
Equipment Return
The PASCO scientific 012-06263A manual is copyrighted and all rights reserved. However, permission
is granted to non-profit educational institutions for
reproduction of any part of the Low Voltage AC/DC
Power Supply manual providing the reproductions are
used only for their laboratories and are not sold for
profit. Reproduction under any other circumstances,
without the written consent of PASCO scientific, is
prohibited.
Should the product have to be returned to PASCO
scientific, for whatever reason, notify PASCO scientific
by letter or phone BEFORE returning the product. Upon
notification, the return authorization and shipping instructions will be promptly issued.
Limited Warranty
When returning equipment for repair, the units must
be packed properly. Carriers will not accept responsibility for damage caused by improper packing. To be
certain the unit will not be damaged in shipment,
observe the following rules:
NOTE: NO EQUIPMENT WILL BE
ACCEPTED FOR RETURN WITHOUT AN
AUTHORIZATION.
ä
PASCO scientific warrants the product to be free from
defects in materials and workmanship for a period of one
year from the date of shipment to the customer. PASCO
will repair or replace, at its option, any part of the product
which is deemed to be defective in material or workmanship. The warranty does not cover damage to the
product caused by abuse or improper use. Determination of whether a product failure is the result of a
manufacturing defect or improper use by the customer
shall be made solely by PASCO scientific. Responsibility for the return of equipment for warranty repair
belongs to the customer. Equipment must be properly
packed to prevent damage and shipped postage or
freight prepaid. (Damage caused by improper packing
of the equipment for return shipment will not be
covered by the warranty.) Shipping costs for returning
the equipment, after repair, will be paid by PASCO
scientific.
➀ The carton must be strong enough for the item
shipped.
➁ Make certain there is at least two inches of packing
material between any point on the apparatus and the
inside walls of the carton.
➂ Make certain that the packing material can not
shift in the box, or become compressed, thus letting
the instrument come in contact with the edge of the
box.
Credits
Author:
Editor:
Hans Frederiksen
Sunny Bishop
ii
Address:
PASCO scientific
10101 Foothills Blvd.
P.O. Box 619011
Roseville, CA 95678-9011
Phone:
(916) 786-3800
FAX:
(916) 786-8905
email:
techsupp@PASCO.com
012-06263A
Low Voltage AC/DC Power Supply
Introduction
The Low Voltage AC/DC Power Supply is intended for
supervised classroom use.
The PASCO scientific Model SF-9584A Low Voltage
AC/DC Power Supply provides two outputs: a regulated
DC output and an unregulated AC output. The DC output can be delivered in two modes: constant voltage
mode and constant current mode.
Operation
DC Output, Limitations
DC Output Operation:
➀ Flip the power ON/OFF switch to OFF.
The DC output is regulated for both constant-voltage and
constant–current operation.
➁ Plug the power cord into a grounded outlet of the appropriate voltage :
Model SF-9584A, 115 V AC (78–130 V AC), 60 Hz
or
Model SF-9584A-230, 230 V AC (200 –242 V AC),
50 Hz.
Constant Voltage mode:
The voltage is continuously variable from 0 –24 V DC.
The maximum load drawn in the range from 0–12 V DC
is 10 A. In the 12 - 24 V range, a load of 10–6 A may be
drawn as the maximum load. At 24 V, the maximum is 6
A. (See the illustration printed on the front panel, “Max.
DC Current,” or Figure 1.)
➂ Connect the 0 –24 V DC OUTPUT terminals of the
power supply to the circuit. (Connecting wires are not
provided with the power supply.)
Constant Current mode:
The load may be varied from 1–10 A in the 1–12 V DC
range. At 12 V, the DC range is variable from 1–10 A.
At 24 V, the range decreases to 0–6 A. (See the illustration printed on the front panel, “Max. DC Current,” or
Figure 1.) A digital meter allows monitoring of both
voltage and current for the DC output.
➃ Rotate the DC VOLTAGE ADJUST knob and the DC
CURRENT ADJUST knob fully counterclockwise.
➄ Flip the power ON/OFF switch to ON. The switch
will light to show that the power supply is on.
➅ Constant Voltage Mode: Turn the DC CURRENT
ADJUST knob fully clockwise. Then adjust the DC
VOLTAGE ADJUST knob to obtain the desired output voltage, as indicated on the meter. The output current is displayed on the current meter.
MAX DC CURRRENT
➆ Constant Current Mode: Turn the DC VOLTAGE
10 A
ADJUST knob fully clockwise. Adjust the DC CURRENT ADJUST knob to obtain the desired output
current, as indicated on the meter. The output voltage
is displayed on the voltage meter.
6A
12 V
24 V
Figure 1. Maximum DC Current
1
Low Voltage AC/DC Power Supply
012-06263A
AC Output Operation:
AC Output Limitations
➀ Flip the power ON/OFF switch to OFF.
The AC output is unregulated and is adjustable in 2-V
increments from 2 to 24 V AC, with a maximum output current of 6 amperes. This output is protected by
a 6-amp circuit breaker. If the maximum current output is exceeded, the circuit breaker button below the
power switch will pop out. (See Figure 2.)
➁ Plug the power cord into a grounded outlet of the appropriate voltage :
Model SF-9584A, 115 V AC (78 - 130 V AC), 60 Hz
or
Model SF-9584A-230, 230 V AC (200 - 242 V AC),
50 Hz.
➂ Connect the 2–24 V AC OUTPUT terminals of the
power supply to the circuit. (Connecting wires are not
provided with the power supply.)
OFF
AC
10
➃ Rotate the AC VOLTAGE ADJUST knob to the
12 14
8
2–V position.
20
6
4
➄ Flip the power ON/OFF switch to ON. The switch
2 24
2-24 V
6 A MAX
will light to show that the power supply is on.
power switch
16
18
ON
22
RESET
circuit breaker
button
➅ Set the AC VOLTAGE ADJUST knob to the desired
setting.
Figure 2. Location of Circuit Breaker Button
The circuit breaker can be reset by simply pushing the
button back in. It may be necessary to reduce the AC
output voltage or the load connected to the AC output in
order to resume operation.
NOTE: If at any time the power supply fails to
come on, or if it shuts down during operation due to
excessive current, check the following: If the
ON/OFF switch does not light when unit is plugged
into the appropriate power source and the switch is
turned ON, check the fuse on the back of the unit.
If it is blown, replace it only with a similarly rated
fuse (Model SF-9584A— 8A Slo-Blo fuse, Model
SF-9584A-230— 4A Slo-Blo fuse).
ä
2
012-06263A
Low Voltage AC/DC Power Supply
Equipment Specifications
Specifications:
Outputs:
Ripple and Noise:
Less than 25 mV pp on DC output.
DC: regulated for both constant–voltage and constant–current operation. Both current and voltage continuously variable over the range 0–24 V DC and 0–10
amperes maximum. Independent floating ground reference.
Metering:
DC voltage and DC current
Accuracy is +1% ± 2 L.S.D.
Line Voltage Requirement:
78–130 V AC, 60 Hz (model SF-9584A)
200–242 V AC, 50 Hz (model SF-9584A - 230)
AC: 2 to 24 V (rms) AC, unregulated, selectable in
2–V increments, current up to 6 amperes. Output protected from overload by a 6-amp thermally-activated circuit breaker. Independent floating ground reference.
Power Requirement:
DC and AC: Maximum 350 W
DC only: Maximum 175 W
AC only: Maximum 175 W
NOTE: Both DC and AC outputs are available
simultaneously on separate floating output terminals.
Either one of the DC output terminals can be connected to either one of the AC output terminals to
form a composite signal without damage to the unit.
ä
Fuse:
8 A Slo-Blo—(model SF-9584A)
4 A Slo-Blo—(model SF-9584A-230)
Line Regulation:
Size:
Less than 1% change in DC output voltage or current for full range change in line voltage. AC output not regulated.
118 x 298 x 229 mm (H x W x D including controls)
Load Regulations:
Better than 1% no-load to full-load on the DC output voltage or current. AC output not regulated.
3
Low Voltage AC/DC Power Supply
012-06263A
Notes:
4
012-06263A
Low Voltage AC/DC Power Supply
Schematics and Parts Lists
ä
Caution: If repairs are needed, they should be performed only by experienced personnel.
Figure 2. Schematic Overview
5
Low Voltage AC/DC Power Supply
012-06263A
Figure 3. Main Board
6
012-06263A
Low Voltage AC/DC Power Supply
Parts List – Main Board
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Reference
R201
R204R206
R220-221
R205
R216 R219
R211 R214 R217
R227
R228
R218 R223
R226
R207 R230
R212
R213 R229
R222
R202-203 R208
R224
R210 R215
TR201-202
TR203-205
C229-234 C243-244
C213 C215 C235
C237-238 C240-241
C224-227
C214 C216-223
C228 C239
C211-212
C207-210 C236
C201-205
C206
D203
D205-209
D201-202
D210
Q205
Q203
Q202
Q201
Q204
U204
U201
U202
U205
U207
U206
RE201-202
J202-208
J200
J213
Part Name
Value
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
TRIMPOT HORIZ
TRIMPOT HORIZ
CERAMIC CAP
CERAMIC CAP
4K7
10K
10K
47K
100K
100R
150R
390R
470R
680R
IK0
4K7
10K
100K
180K
IM0
0.01R
220R
10K
1.0nF
10nF
250V
250V
250V
250V
250V
250V
250V
250V
250V
250V
250V
250V
250V
250V
250V
250V
20mV
250V
250V
63V
63V
STACK FOIL CAP
STACK FOIL CAP
100nF
100nF
STACK FOIL CAP
ELECTROLYT CAP
ELECTROLYT CAP
ELECTROLYT CAP
DIODE
DIODE
DIODE
ZENER-DIODE
NPN TRANSISTOR
PNP TRANSISTOR
NPN TRANSISTOR
Nch MOSFET
Nch MOSFET
DualOpAmp
IC
VOLTAGE REGULATOR
VOLTAGE REGULATOR
VOLTAGE REGULATOR
RAIL SPLITTER
RELAY 5V
CONNECTOR
3M-929 20 PIN
STOCKO MKS4
470nF
4.7UF
100UF
1000UF
BYV27-200
lN4148
2W04M
BZX79-C2V7
BC547B
BC557B
BC639
BUK456-60A
BS170
LTll12
LM614
LM317
LM78L05
LM7805
TLE2426CLP
M4-5H
6.3 MM
20 PIN
4 PIN
7
Qty Stock No.
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
2W
0.lW
0.lW
1
2
2
1
2
3
1
1
2
1
2
1
2
1
3
1
2
2
3
8
7
601074
601082
601083
601099
601106
6030701
6030801
6031051
6031101
6031201
6031301
6031701
6031901
6032501
6032651
6033101
604301
605935
605960
611890
612010
400V
63V
4
11
613170
613450
63V
25V
63V
35V
200V
75V
400V
2.7V
50V
50V
100V
60V
60V
30V
36V
40V
35V
35V
40V
125V/30W
2
5
5
1
1
5
2
1
1
1
1
1
1
1
1
1
1
1
1
2
7
1
1
613530
615643
615785
616003
623267
623300
623665
624060
624710
624720
624750
625690
626120
630211
631214
632130
632430
632533
634941
637428
641245
641321
641357
2A
0.2A
2A
0.5W
0.lA
0.2A
1.5A
52A
0.5A
10mA
0.3mA
lA
0.1A
1.5A
0.08A
1A
Low Voltage AC/DC Power Supply
012-06263A
Figure 4. Display Unit
8
012-06263A
Low Voltage AC/DC Power Supply
Parts List – Display Unit
Item Reference
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
30
R101 R111
R107-108
R117-118 R120
R103 R113
R104 R114
R100 R102
R105-106 R110
R112 R115-116
P1-2
C103 C123
C112 C132
C109-110
C129-130
C102 C104
C106-10 C111
C122 C124
C126-128 C131
C105 C125
C101 C121
D101-102
DS101-108
D103-104
D105-106
U102 U104
U101 U103
SW101
J102-103
J101
U101 U103
Part Name
Value
Qty Stock No.
RESISTOR
RESISTOR
330R
1K0
250V
250V
0.4W
0.4W
2
5
6031001
6031301
RESISTOR
RESISTOR
RESISTOR
6K8
47K
100K
250V
250V
250V
0.4W
0.4W
0.4W
2
2
8
6031801
6032301
6032501
POTMETER
CERAMIC CAP
CERAMIC CAP
CERAMIC CAP
10K
100pF
1.0nF
10nF
300V
63V
63V
63V
1.5W
2
2
2
4
608251
611770
611890
612010
STACK FOILCAP
100nF
63V
12 613450
STACK FOIL CAP
ELECTROLYT CAP
LED
DISPLAY
DIODE
DIODE
VOLTAGE REF.
IC
SWITCH LOCKING
HEADER
3M-929
TULIPAN
470nF
100UF
HLMP-1719
HDSP-5301
1N4148
1N4007
LM385
ICL7107
MK2
16 PIN
20 PIN
SOK
63V
25V
2V
2V
75V
700V
20mA
9V
120V
500V
20 PIN
40 PIN
2
2
2
8
2
2
2
2
1
2
1
2
9
2mA
20mA
0.2A
1A
250mA
2.5A
613530
616440
622000
622940
623300
623390
631185
635057
638031
641029
641321
635539
Low Voltage AC/DC Power Supply
012-06263A
Figure 5. Switch-Mode Regulator
10
012-06263A
Low Voltage AC/DC Power Supply
Parts List – Switch-Mode Regulator
Item Reference
Part Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
CERAMIC CAP
CERAMIC CAP
CERAMIC CAP
STACK FOIL CAP
STACK FOIL CAP
ELECTROLYT CAP
ELECTROLYT CAP
ELECTROLYT
DIODE
ULTRA FAST DIODE
DIODE
DIODE BRIDGE
ZENER-DIODE
ZENER-DIODE
NPN TRANSISTOR
Pch MOSFET
IC
R3
Rl-2
R14
R10 R12
R9
R8
R5
R7
R4 R13
R6
Rll
CI2 C14 C19
Cll
C7-8 C13
C17-18
C2-4 C15
C9-10
C5-6 C16
Cl
Dl
D2
D4-7
D10
D9
D8
Q2-3
Ql
Ul
Value
2K2
10K
0R
10R
100R
470R
3K3
4K7
47K
IK0
0.01R
1.0nF
4.7nF
10nF
100nF
470nF
2.2UF
100UF
CAP
BYV27-200
BYV79-100
lN4007
PBU802
BZV85-C15
BZV85-C33
BC639
SMP40P06
LM3524
11
250V
250V
250V
250V
250V
250V
250V
250V
250V
500V
20mV
63V
63V
63V
400V
63V
63V
63V
6800UF
200V
100V
700V
100V
15V
33V
100V
60V
40V
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
0.4W
1.6W
2W
63V
2A
14A
lA
8A
1.0W
1.0W
1.5A
40A
Qty
Stock No.
1
2
1
2
1
1
1
1
2
1
1
3
1
3
2
4
2
3
1
1
1
4
1
1
1
2
1
1
601066
601083
6020901
6030101
6030701
6031101
6031601
6031701
6032301
603810
604301
611890
611970
612010
613170
613530
615622
615785
616102
623267
623268
623390
623685
624515
624533
624750
626110
632350
Low Voltage AC/DC Power Supply
012-06263A
Figure 6. Filter Board
Parts List – Filter Board
Item Reference
Part Name
1
2
STACK FOIL CAP
H1-4
C301-303
Value
100NF
12
Qty
400V
4
3
Stock No.
613170
012-06263A
Low Voltage AC/DC Power Supply
Technical Support
Feedback
Contacting Technical Support
If you have any comments about the product or manual,
please let us know. If you have any suggestions on alternate experiments or find a problem in the manual, please
tell us. PASCO appreciates any customer feedback.
Your input helps us evaluate and improve our product.
Before you call the PASCO Technical Support staff, it
would be helpful to prepare the following information:
➤ If your problem is computer/software related, note:
­ Title and revision date of software;
To Reach PASCO
­ Type of computer (make, model, speed);
For technical support, call us at 1-800-772-8700 (toll-free
within the U.S.) or (916) 786-3800.
­ Type of external cables/peripherals.
fax:
➤ If your problem is with the PASCO apparatus, note:
(916) 786-3292
­ Title and model number (usually listed on the label);
e-mail: techsupp@PASCO.com
web:
­ Approximate age of apparatus;
www.pasco.com
­ A detailed description of the problem/sequence of
events. (In case you can’t call PASCO right away,
you won’t lose valuable data.);
­ If possible, have the apparatus within reach when
calling to facilitate description of individual parts.
➤ If your problem relates to the instruction manual, note:
­ Part number and revision (listed by month and year
on the front cover);
­ Have the manual at hand to discuss your questions.
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising