Video Navigation In-Motion Controller NDS6223EP - Beat

Video Navigation In-Motion Controller NDS6223EP - Beat
Video Navigation In-Motion Controller NDS6223EP
NO:1
Thank you for purchasing the Beat-Sonic Video Navigation In-Motion Controller. You have
purchased from Japan`s leading manufacturer of car audio interface adapters and accessories.
Designed and made in Japan, this product represents our commitment to excellence and quality in
manufacturing.
Please read this manual carefully prior to installing and using this product to ensure correct
operation.
Navigation and Video In-Motion Controller
This device provides automatic video in motion for the DVD player at all times. Navigation in
motion is activated by the steering wheel volume control buttons by pressing volume up (+), down
(-), up (+), down (-) in sequence and at normal cadence. While navigation in motion is activated, the
navigation system will temporarily lose its GPS location and the position indicator on the
navigation screen will stop moving. By default, a programmable timer will reset the navigation in
motion to switch off after 3 minutes.
Navigation in motion can be switched off before the timout period has expired by repeating the
volume control button sequence up (+), down (-), up (+), down (-).
International enquiries.
This device is suitable for Lexus generation 7 and 8 navigation systems. The full time video in
motion feature is compatible with all navigation system features including Lexus App Suite,
Enform App Suite and energy consumption display found on hybrid models.
株式会社 ビートソニック
472-5, Koushin, Fujieda, Nisshin, Aichi, JAPAN.
TEL: +81-561-73-9000 FAX: +81-561-74-5554
www.world-beatsonic.com E-mail: enquiries@beatsonic.co.jp
USA and Canada enquiries.
DISCLAIMER
This product is designed for use by the passenger(s) of the vehicle. Under no
circumstances should the driver operate the navigation system, watch video or
otherwise be distracted while the vehicle is in motion.
Beat-Sonic USA Inc.
14778 Beach Blvd. La Mirada, CA 90638
TEL: 1-714-994-1085 FAX: 1-714-249-4741
www.beatsonicusa.com E-mail: info@beatsonicusa.com
Depending on local traffic laws, it may be an offense for the driver to view the screen
while the vehicle is in motion.
Beat-Sonic and its affiliates accept no responsibility for personal injury, damage to
property, vehicle breakdown, breaches of traffic laws, traffic infringements etc. as a
result of using the product.
Please use this product in a safe and responsible manner.
WARNING
During installation always perform all operations with patience and due care so as not to damage
interior trim, wiring or any others parts. Be especially cautious of sharp edges that may damage
cables and/or cause injury to the installer.
Install this device in a location where it will not interfere with the operation of the vehicle. Do not
install in areas of high humidity, dust or where it is likely to get wet.
Always use this product in accordance with local traffic regulations. Distracted driving can cause a
serious accident, cause injury and break the law. Beat-Sonic and its affiliates shall not be held
responsible for any consequence, either directly or otherwise, as a result of using this product.
User Manual
How to Program
Operation – Video in Motion
The NDS6223EP features full time Video In Motion (VIM) without the need to turn on or off. All
OEM systems including navigation and energy monitor on hybrid vehicles will continue to work as
normal.
Operation – Navigation in Motion
Navigation In Motion is activated via the steering wheel volume button by pressing up (+), down
(-), up (+), down (-) in sequence and at normal cadence.
Navigation Status
Nav Unlock Activate /
Nav Unlock Cancel
Nav Unlock Activate
(Timer Override Mode*)
Nav Unlock Cancel
(automatic timeout)
Volume Button Sequence
up (+), down (-), up (+), down (-)
Audible Confirmation
2 short beeps for activation
4 short beeps for cancellation
up (+), down (-), up (+), down (-),
up (+), down (-), up (+), down (-)
1 long beep**
No input – inbuilt timer (default 3 min). 4 short beeps
Connection & Initialization
1.
2.
3.
4.
Install the NDS6223EP in vehicle using the procedure detailed overleaf.
Reconnect battery and turn ignition ON.
Allow navigation initialization process to fully complete.
Turn ignition OFF.
Programming Mode
1.
2.
3.
4.
Press & hold VOLUME DOWN button on steering wheel.
Turn ignition ON while holding VOLUME DOWN button until beep is heard.
Release VOLUME DOWN button to enter programming mode.
Mode Selection
Press VOLUME UP to cycle through the 2 different mode settings as shown below.
Audible beep(s) will be heard through the vehicles sound system to indicate the selected mode.
- Mode 1 selection is indicated by a single beep.
VOLUME UP
- Mode 2 selection is indicated by two beeps.
Mode
* Navigation In Motion will always return to OFF when the ignition is turned ON.
** Depending on present navigation in motion status, 2 or 4 beeps will be heard mid sequence
followed by one long beep after the sequence is completed.
While navigation in motion is activated, the navigation system will temporarily lose its GPS location
and the position indicator on the navigation screen will stop moving. Operation will return to
normal shortly after navigation in motion is deactivated either by the inbuilt timer or by again
pressing the steering wheel volume button up (+), down (-), up (+), down (-).
Programmable Settings
Navigation In Motion Timer
Selectable 2 min, 3 min (default), 4 min or no timer.
Steering Wheel Volume Button Activation
- Mode 1 (Default)
Slight volume response lag but does not alter the current volume setting.
- Mode 2 (Selectable)
Zero volume lag however volume will change together with button presses to activate
navigation in motion.
Mode 1
(default)
Mode 2
●
(1)
●●
(2)
Beep
Mode 1: Volume does not change when activating Navigation In-Motion.
(default) All inputs registered but slight delay on first volume up press.
Mode 2: Volume changes when activating Navigation In-Motion.
i.e. Volume increases by 1, decreases by 1, increases by 1, decreases by 1.
5. Timer Selection
Press VOLUME DOWN to cycle through the timer settings as shown below:
Audible beep(s) will be heard through the vehicles sound system to indicate the selected timer setting.
- No Timer selection is indicated by a single beep.
- 2 min. Timer selection is indicated by two beeps.
- 3 min. Timer selection is indicated by three beeps.
- 4 min. Timer selection is indicated by four beeps.
VOLUME DOWN
Timer
No Timer
2min
3min
(default)
4min
Short Beep
●
(1)
●●
(2)
●●●
(3)
●●●●
(4)
6. Complete and Exit Programming Mode
Press and hold VOLUME DOWN until long beep is heard to complete and exit programming mode.
BEFORE YOU START
⑤ Separate the 24-pin connector block from the 59-pin connector.
Prior to commencing electronic work, disconnect the battery negative (-) terminal to prevent
component and wire damage caused by accidental short circuits.
Switch the headlight dimmer OFF and the ignition to the OFF position before waiting for the
prescribed duration shown in the chart below before disconnecting the battery.
Vehicle enrolled in safety connected system
6 minutes
Vehicle not enrolled in safety connected system
1 minute
Please note clock settings, radio settings, audio system memory, seat memory position, steering
column memory positions, DTCs and other data are cleared when the battery is disconnected.
View from harness side
27-Pin
8-Pin
24-Pin
27-Pin
8-Pin
24-Pin Block
⑥ Connect the 24-pin block to male side of the NDS6223EP 24-pin connector.
Connection Diagram
To Navigation
Receiver 24-Pin
Connector
To Vehicle Harness
24-Pin Connector
Insert fully and wrap firmly with
supplied insulating tape
*Do not bend or damage pin terminals.
To Navigation
Receiver 12-Pin
Connector
To Vehicle Harness
12-Pin Connector
To Navigation
Receiver GPS
Connector
NDS6223EP
NDS6223EP 24-Pin
Female Connector
Controller Unit
GPS Connector
Vehicle Side 24-Pin
Female Connector
⑦ Attach 24-pin female side of the NDS6223EP connector to the remaining 35-pin
connector as shown below.
Navigation Receiver Unit
Wrap with supplied
insulating tape
59P
NDS6223EP 24-Pin
Female Connector
12P
Vehicle Side 24-Pin
Female Connector
GPS Antenna
Installation Procedure
■ Removal of the navigation receiver unit
⑧ Attach the release lever to the 59-pin connector as illustrated below before
re-connecting to the navigation unit.
Disassembly of the centre panel and various trim panels to remove the navigation
unit varies greatly according to each vehicle. Please check with your motor vehicle
dealer to obtain all necessary instructions and take due care during installation so
as not to damage any parts.
① Turn ignition to OFF and wait the prescribed time before disconnecting the battery
negative (-) terminal.
Ensure slider is seated correctly
beneath locating tab.
② Remove all necessary parts to allow access to the rear of the navigation receiver unit.
③ Disconnect the 59-pin connector from the navigation receiver by pulling back on the
grey release lever.
⑨ Disconnect the 12-pin plug and GPS plug from the navigation receiver and connect
them both to the corresponding connectors on NDS6223EP.
12Pin
GPS
Controller Unit
Release Lever
④ Remove the release lever from the 59-pin connector.
⑩ Connect the remaining 12-pin plug and GPS plug from the NDS6223EP to the
navigation receiver.
⑪ Secure the NDS6223EP controller unit to a clean, flat surface using the supplied
double sided tape. Ensure the controller unit does not obstruct other parts especially
the navigation unit when it is re-installed.
NDS6223EP
Double sided tape
Lift tabs on both sides while sliding
the lever to the closed position
Flat surface
⑫ Return all disassembled parts to their original position to complete the installation.
機 種 NDS6223EP
担 当 ‘15.08/21
対応図面 取扱説明書・NDS6223EP
神谷
対応図番 M406848
品
原稿・取扱説明書NDS6223EP
設 計 知 財 営 業 照 査 検 認 名
図
番
N406878-01
原稿外寸(mm)
データサイズ:
A3両面
使用材質:
上質紙
加工方法:
十字折
2015.8.4:WPG神谷
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising