XL 2200 - Precision Gradall Ltd

XL 2200 - Precision Gradall Ltd
XL 2200
XL 2200
H Y D R A U L I C
E X C AVAT O R
SPECIFICATIONS
Upperstructure Engine
Cummins 4BT3.9 diesel, turbocharged, liquid
cooled, 4 cycle, 4 cylinder, 239 cid (3.9L).
4.02" bore x 4.72" stroke (102mm x 120mm),
18.5:1 compression ratio.
95 hp (71kW) gross at 2200 rpm, 82 hp
(61kW) net at 2200 rpm. 283 ft-lb (384Nm)
gross torque at 1500 rpm.
Altitude capability 9850' (3000m). Derate
4% per 1500’ (457m) above 9850' (3000m).
Maximum slope: 45°
12 volt starter, 105 amp alternator, one
SAE #C31-S 810 CCA battery, two-stage dry
type air cleaner with centrifugal precleaner,
ejector valve and service indicator, spin-on
oil filter, spin-on fuel filter/water separator.
Fuel tank capacity: 55 gallons (208L)
Filtration system
10 micron return filter with magnet and 100
mesh strainer in reservoir.
Fin and tube-type oil cooler, with thermal
by-pass and relief valves.
Pressure compensated load-sensing
valves with circuit reliefs in all circuits.
Upperstructure Cab
All-weather cab with tinted safety glass
windows, skylight, acoustical lining,
four-way adjustable operator's seat, filtered
fresh air heater and defroster. Front
window slides to overhead storage.
Rearview mirrors on right and left sides.
Undercarriage
Tractor type crawler with triple grouser
heavy-duty pads.
Sealed track links, lubricated and sealed
idlers and rollers, hydraulic track tension
adjustment, track guides, motor and hose
guards, front and rear tow eyes.
Track length: 9'10" (3m)
Track pads: 19.7" (500mm) or 23.6" (600mm)
Overall width: 8'2" (2.5m) with 19.7" (500mm) pads
8'6" (2.6m) with 23.6" (600mm) pads
Ground clearance: 18" (45.7cm)
Crawler Drive
Controls
Hydraulic System
PUMPS
Two load-sensing axial piston pumps;
0 - 43.5 GPM (0 - 164 L/min) each.
SYSTEM MONITOR
Electronic monitor in cab indicates low
hydraulic fluid level, high hydraulic fluid
temperature, and condition of return and
suction filters.
SYSTEM SPECIFICATIONS
Three double acting cylinders
• 1 boom hoist: 4.75" ID, 3.0" rod
(121mm x 76mm), 28" (711mm) stroke.
• 1 tool: 4.5" ID, 2.5" rod (114mm x
63mm), 17.75" (450mm) stroke.
• 1 telescope: 3.5" ID, 2.25" rod
(88mm x 57mm), 9'5" (2.89m) stroke.
Four hydraulic motors
Swing, 42 hp (31kW); tilt, 12.6 hp (9kW);
two crawler drives, 76 hp (56kW) each.
Operating pressures
Hoist . . . . . . . . . . . . . . . . . . . . . . . 3950
Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . 1800
Swing . . . . . . . . . . . . . . . . . . . . . . 2875
Tool . . . . . . . . . . . . . . . . . . . . . . . . 3950
Telescope . . . . . . . . . . . . . . . . . . . 3150
Crawler . . . . . . . . . . . . . . . . . . . . . 3950
Pilot system . . . . . . . . . . . . . . . . . . 480
psi
psi
psi
psi
psi
psi
psi
Oil capacity
Reservoir 33 gallons (125L), system 55
gallons (208L). Pressurized reservoir with
visual oil level gauges.
Two hydraulic joysticks (hoist & bucket,
telescope & swing), one rocker switch (tilt)
control upperstructure. Hydraulic joysticks
mounted on arm rests, independently
adjustable for individual operator comfort
and convenience.
Two foot pedals with handles control
crawler steering, travel and brakes; toggle
switch for selection of crawler speed range.
Joysticks and pedals are self-centering;
when controls are released, power for
movement disengages and swing, tilt, and
crawler brakes set automatically.
Engine controls
Key operated ignition/starter switch,
throttle, hour meter and air cleaner
condition indicator. Electronic monitor
indicates fuel level, low battery charge,
coolant level and lube oil pressure, high
coolant temperature, and engine rpm.
Swing
Priority swing circuit with axial piston motor.
Planetary transmission.
Dual range high torque piston motor, 76 hp
(56kW), powers each track. Three stage
planetary drive with integral speed limiting
valve and automatic spring-set hydraulic
release wet disc parking brake.
Travel speed on flat, level surface–mph (km/hr):
Speed Selector MPH (km/h)
High
3.44 (5.53)
Low
Travel speed range can be shifted while moving.
Gradeability: 97%.
Drawbar pull: 18,800 lb (83kN)
Individual track control. Tracks counter-rotate
to pivot machine around on centerline.
Electronically operated travel alarm signals
crawler movement in either direction.
Weight
Approximate working weight with 36" (91cm)
bucket, fuel tank half full:
19.7" Pads
(500mm)
23.6" Pads
(600mm)
Weight
26,615 lb
(12,072 kg)
26,990 lb
(12,242 kg)
Bearing
Pressure
6.86 psi
( .48 kg/cm2)
5.8 psi
( .41 kg/cm2)
Swing speed: 0 - 9 rpm.
Swing brake:
Automatic swing parking brake, spring-set
hydraulic release. Dynamic braking provided
by hydraulic system.
2.34 (3.76)
Rated bucket breakout force: 17,030 lb (75.8).
Rated boom force: 17,780 (79.2 kN).
GRADALL XL 2200 CRAWLER RATED LIFT CAPACITY OVER END OR SIDE-LB (KG)
LOAD RADIUS
LOAD
POINT HEIGHT
Above
Ground
Level
10’ (3.0m)
15’ (4.6m)
20’ (6.1m)
Maximum Radius
15' (4.6m)
3095 @ 16'1"
(1405 @ 4.9m)
10' (3m)
7250 @ 10'8"
(3290 @ 3.3m)
4365
(1980)
2610
(1185)
2435 @ 20'8"
(1105 @ 6.3m)
Boom Level
6'5” (2m)
7035 @ 11'11"
(3190 @ 3.6m)
4800
(2175)
2815
(1280)
2470 @ 21'4"
(1120 @ 6.5m)
7015 @ 12'0"
(3185 @ 3.7m)
4880
(2215)
2865
(1300)
2495 @ 21'4"
(1130 @ 6.5m)
6880 @ 10'9"
(3120 @ 3.3m)
4515
(2050)
2785
(1260)
2595 @ 20'9"
(1175 @ 6.3m)
5'
(1.5m)
At Ground Level
Below
Ground
Level
Minimum Radius
2460 @ 18'7"
(1115 @ 5.7m)
5' (1.5m)
2850 @ 6'5"
(1295 @ 1.9m)
4480
(2035)
10' (3m)
1635 @ 7'9"
(745 @ 2.4m)
2460
(1115)
3525
(1600)
2680 @ 18'8"
(1215 @ 5.7m)
2520 @ 14'4"
(1140 @ 4.4m)
CAUTION: All rated loads are based on the machine being stationary and level on a firm supporting surface. For safe
working loads, the user is expected to make due allowance for his particular job conditions, such as soft or uneven
ground, out of level conditions, side loads, hazardous conditions, experience of personnel, etc. The operator and
other personnel should fully acquaint themselves with the Operator's Manual furnished by the manufacturer before
operating this machine, and rules for safe operation of equipment should be adhered to at all times.
The above loads are in compliance with SAE Standard J1097 Nov88. They do not exceed 87% of hydraulic lifting capacity or
75% of tipping capacity.
All loads with an asterisk (*) indicate the load is limited by tipping rather than hydraulic capacity. The rated lift capacity is based
on the machine being equipped with 3200 lb (1450kg) counter-weight, 23.6" (600mm) or 19.7" (500mm) tracks, and 8025-6002 36"
(91cm) excavating bucket weighing 700 lb (318kg). For other buckets adjust the listed capacities as follows:
8025-6001
60" (152cm) ditching - subtract 150 lb (68kg)
8025-6003
30" (76cm) excavating - subtract 85 lb (39kg)
8025-6004
24" (61cm) excavating - subtract 155 lb (70kg)
8025-6005
18" (46cm) excavating - add 250 lb (113kg)
8025-6006
30" (76cm) pavement removal - subtract 329 lb (149kg)
8025-6012
60" (152cm) ditching constant radius - subtract 125 lb (57kg)
The load point is located on the bucket pivot point, including loads listed for maximum radius. Do not attempt to lift or hold any
load greater than these rated values at specified load radii and heights. The weight of slings and any auxiliary lifting devices
must be deducted from the rated load to determine the net load that may be lifted.
A
A1
BA
E
BH
G
AP
D
B
BJ
AQ
BB
J3
J4
AK
BF
AW
AL
J1
J2
BD
AU
BE
BG
AV
BC
AS
AF
C1
AX
AH
N
F
AC
AA
AB
AG
AP
Y
AD
V
K
Shown with 8025-6002 36" (760 mm) excavating bucket
A
A1
B
C1
D
E
F
G
J1
J2
J3
J4
K
N
V
Y
AA
AB
AC
AD
AF
AG
AH
AK
Overall length with bucket: 22'1" (6.7)
Overall length without bucket: 19'4" (5.9)
Overall height with bucket: 9'3" (2.8)
Width of upperstructure: 7'5" (2.3)
Minimum clearance, upperstructure to undercarriage: 3" (76 mm)
Swing clearance, rear of upperstructure: 7' (2.1)
Top of cab to groundline: 9'3" (2.8)
Clearance, upperstructure to groundline: 35" (890 mm)
Axis of rotation to centerline of drive sprockets: 3'10" (1.2)
Nominal distance between centerlines of drive sprockets
and idlers: 7'7" (2.3)
Axis of rotation to end of track assembly: 5' (1.5)
Nominal overall length of track assembly: 9'10" (3.0)
Width of crawler (standard): 8'6" (2.6)
Width of crawler (optional): 8'2" (2.5)
Ground clearance (per SAE J1234): 18" (460 mm)
Track gauge, roller centerline to roller centerline: 6'6" (2.0)
Width of crawler track assembly (standard): 23.6" (600 mm)
Width of crawler track assembly (optional): 19.7" (500 mm)
Maximum radius at groundline (165° pivot): 24'0" (7.3)
Maximum digging depth: 16'5" (5.0)
Maximum depth for 8' level cut: 14'4" (4.4)
Minimum radius for 8' level cut at depth "AC": 5'8" (1.7)
Maximum depth of vertical wall which can be excavated: 3'9" (1.1)
Minimum level cut radius with bucket flat on groundline: 10'4" (3.1)
Minimum radius at groundline: 6'10" (2.1)
Boom pivot to groundline: 4'11" (1.5)
AL
AP
AQ
AS
AU
AV
AW
AX
BA
BB
BC
BD
BE
BF
BG
BH
BJ
Boom pivot to axis of rotation: 24" (610 mm)
Bucket tooth radius: 3'2" (960 mm)
Boom pivot angle: 30° Up & 75° Down
Bucket pivot angle: 135° & 165°
Maximum telescoping boom length (boom pivot to bucket
pivot): 19'4" (5.9)
Minimum telescoping boom length (boom pivot to bucket
pivot): 9'11" (3.0)
Telescoping boom travel: 9'5" (2.9)
Bucket tilt angle: 360° (continuous)
Maximum radius of working equipment (165° pivot): 24'6" (7.5)
Maximum height of working equipment: 18'11" (5.8)
Maximum bucket tooth height: 17'6" (5.3)
Minimum clearance of bucket teeth with bucket pivot
at maximum height: 12'10" (3.9)
Minimum clearance of fully curled bucket at maximum
boom height (165° pivot): 8'5" (2.6)
Minimum clearance of bucket teeth at maximum boom
height: 8'2" (2.5)
Maximum height of working equipment with bucket below
groundline: 12'8" (3.9)
Radius of bucket teeth at maximum height (165° pivot): 20'8" (6.3)
Minimum radius of bucket teeth at maximum bucket pivot
height (165° pivot): 15'7" (4.7)
Metric units are m unless noted
Units shown may have optional equipment
Optional Equipment
Work lights: 2 floodlights on boom
cradle, 3 floodlights on cab, 2 floodlights
on left front shrouding.
Windshield washer and wiper.
Vandalism protection kit: Lexan cab
windows, locking reservoir cap and sight
gauge cover; locking engine hood, fuel
cap and battery box.
Spark arrestor.
Revolving beacon.
Cu.
yd.
m3
Cu.
yd.
m3
Cold start package for engine: includes
ether start kit and additional battery.
8025-6005 18" (460mm)
Excavating bucket
3/16
.15
8025-6001 60" (1.5m)
Ditching bucket
3/4
.61
Air conditioning.
8025-6004 24" (610mm)
Excavating bucket
1/4
.31
8025-6012 60" (1.5m)
Constant radius
ditching bucket
5/8
.53
Inside hose trough with additional hosing
and piping for pneumatic or hydraulic
powered attachments.
8025-6003 30" (760mm)
Excavating bucket
3/8
.29
8025-6002 36" (910mm)
Excavating bucket
1/2
.38
8025-6013 8' (2.4m) Grading blade with
bolt on edge
8025-6006 30" (760 mm)
Pavement removal bucket
ATTACHMENTS
Buckets fabricated of steel plate, with
high strength, low alloy cutting edges
and wear strips. Standard attachments
available for wide range of applications.
Capacities shown are in heaped cu. yd.
TWO POSITION BUCKET
It is Gradall Policy to continually improve
its products. Therefore designs, materials
and specifications are subject to change
without notice and without incurring any
liability on units already sold. Units shown
may have optional equipment.
A - Bucket open, lower pin position, for
vertical walls or deep excavating.
Bucket pivot 165°.
B - Bucket open, upper pin
position, for most applications.
Bucket pivot 135°.
C - Bucket closed, either pin position.
406 Mill Ave. SW, New Philadelphia, Ohio 44663
Phone (330) 339-2211 FAX (330) 339-8468
http://www.gradall.com
Certified ISO 9001
Form No. 10017 7/00
Replaces Form No. 19806
Printed in
USA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising