Idle-Lock™ IDLE552-A

Idle-Lock™ IDLE552-A
An ISO 9001:2008 Registered Company
Idle-Lock™ IDLE552-A
Anti-Theft
2007-2011 Ford Crown Victoria Police Interceptor
Contact InterMotive for additional vehicle applications.
Introduction
Idle-Lock is an anti-theft system that allows an unattended vehicle’s engine to idle with the key removed from
the ignition and the shifter locked in park. The system is activated by pressing a momentary enable switch and
removing the key within three seconds. Idle-Lock is instantly disabled when the key is inserted and turned to
Run.
Installation Instructions
Disconnect vehicle battery before proceeding with installation
It is the installer’s responsibility to route and secure all wiring harnesses where they cannot be damaged
by sharp objects, mechanical moving parts and high heat sources. Failure to do so could result in damage
to the system or vehicle and create possible safety concerns for the operator and passengers.
It is important to avoid placing the module where it could encounter strong magnetic fields from high
current cabling connected to motors, solenoids, etc. Also avoid radio frequency energy from antenna’s or
inverters next to the module. Finally, avoid high voltage spikes in vehicle wiring by always using diode
clamped relays when installing up fitter circuits.
IDLE552 Module
Remove the lower dash panel below the steering column and find a suitable location to mount the module.
Locate the module in an area away from excessive heat sources (engine, heater ducts, etc.). Ensure when
routing harnesses that the tilt steering column does not contact them in the full down position. Do not
mount the module until all wire harnesses are routed and secure. The last step of the installation is to
mount the module. When installing the harnesses, leave several inches of take-out so the module can be
removed if necessary.
Data Link Harness Installation
1. Locate the vehicle’s OBDII Data Link Connector. It will be mounted below the
lower left dash panel.
2. Remove the mounting screws for the OBDII connector. Plug the Red connector
from the Idle-Lock Data Link Harness into the vehicle’s OBDII connector. Ensure
the connection is fully seated and secure with the supplied wire tie.
3. Mount the Black pass through connector from the Idle-Lock Data Link Harness
in the former location of the vehicle’s OBDII connector.
4. Secure the Idle-Lock Data Link harness so that it does not hang below the lower
dash panel.
5. Plug the free end of the Data Link harness into the mating 6-pin connector on
the Idle-Lock module.
InterMotive Inc.
12840 Earhart Ave.
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 1 of 6
Data
Link
Harness
plugs in
here
www.intermotive.net
products@intermotive.net
IDLE552-A-061317-INS
Ignion Switch harness Installaon
•
Remove the lower steering column housing by
removing the 3 screws.
•
Locate the 10 pin Ignition Switch Connector.
•
Remove the 10 pin connector from the Ignition
Switch.
•
Plug the OEM harness side of the 10 pin Ignition
Switch into the mating Intermotive Ignition Switch ‘T’
Harness (see picture).
•
Plug the other end of the Intermotive Ignition Switch
‘T’ harness into the OEM Ignition Switch (see picture).
InterMotive Inc.
12840 Earhart Ave.
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 2 of 6
www.intermotive.net
products@intermotive.net
IDLE552-A-061317-INS
Idle-Lock Enable Switch and Active LED
An switch with an integrated LED is provided in the kit. The switch
is used to enable Idle-Lock. The LED will flash to indicate when IdleLock is active.
1. Drill a 16mm (0.630”) hole in the desired mounting location.
One possibility is the dash panel to the left of the Steering
Wheel.
2. Route the LED harness through the hole and mount the LED in
the hole.
3. Slide the LED’s lock nut onto the harness and snug it down onto
the back of the LED.
4. Plug in the 4 pin (Black) connector of the LED harness into the
mating connector on the Idle-Lock main harness.
5. Apply optional “Idle-Lock Enable/Active” label included in the kit.
IDLE552 Harness (4 Pin connector and 12 Pin connector)
1. Plug the IDLE552 12 Pin connector into the mating 12 pin connector on the IDLE552 module.
2. Plug the IDLE552 4 Pin connector into the mating 4 pin connector on the IDLE552 module.
Reconnect the vehicle battery
InterMotive Inc.
12840 Earhart Ave.
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 3 of 6
www.intermotive.net
products@intermotive.net
IDLE552-A-061317-INS
Post Installation Operational Test
Test 1. Start the Engine.
Test 2. While the engine is running, enable Idle-Lock by momentarily pressing the enable switch.
•
The Red LED will flash five times and then blink every two seconds.
•
Remove the key from the ignition within 3 seconds, the engine will continue to idle.
•
Idle-Lock is now active.
Test 3. Attempt to shift the vehicle out of Park. The system will keep the shifter locked.
Test 4. Verify that weapon rack and trunk release switches are disabled 10 seconds after removing the
key in Idle-Lock mode (if wired).
Test 5. Insert key and turn to RUN. The vehicle should be able to shift out of Park and the trunk and
weapons rack release switches should operate normally.
•
The system will deactivate (shut down engine) if anyone defeats the OEM shift lock mechanism and
shifts the vehicle out of Park.
If the system fails any of the above tests, check the related wiring. If necessary, call
InterMotive Technical Support at 530-823-1048. Do NOT release vehicle for service
unless it has passed ALL of the above tests.
IDLE552 Module Mounting
Ensure all harnesses are properly connected and routed, and are not hanging below the dash area. Mount the
module as described on page one and secure with supplied screws or double sided tape.
InterMotive Inc.
12840 Earhart Ave.
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 4 of 6
www.intermotive.net
products@intermotive.net
IDLE552-A-061317-INS
Leave in vehicle
Idle-Lock™ IDLE552-A
Operating Instructions
2007-2011 Crown Victoria Police Interceptor
Idle-Lock is an anti-theft system that allows an unattended vehicle’s engine to idle with the key removed
from the ignition and the shifter locked in park. The system is activated by pressing a momentary enable
switch and removing the key within three seconds. Idle-Lock is instantly disabled when the key is inserted
and turned to Run.
• Idle-Lock is activated by pressing the Idle-Lock enable switch and removing the key from the ignition within
3 seconds. Idle-Lock can only be enabled with the engine running and the transmission in park.
• When active, Idle-Lock will disable the weapons rack and trunk release switches (if wired) 10 seconds after
the key is removed.
• To prevent unattended vehicle theft (Idle-Lock active), the engine will turn off if someone successfully
defeats the OEM shift lock mechanism to shift the vehicle out of Park. The trunk and weapons rack
release buttons will remain disabled.
• Inserting the key and turning it to Run restores normal operation. Trunk and weapons rack release
buttons are restored to normal operation.
InterMotive Inc.
12840 Earhart Ave.
Auburn, CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
Page 5 of 6
www.intermotive.net
products@intermotive.net
IDLE552-A-061317-OP
Submit product registration at www.intermotive.net
IDLE552-A-061317-CAD
If the Idle-Lock552 fails any step in the Post Installation Test, review the installation instructions
and check all connections. If necessary, call
InterMotive Technical Support at (530) 823-1048.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising