Cylindrical Lockset IN120 WiFi Installation Instructions

Cylindrical Lockset IN120 WiFi Installation Instructions
Cylindrical Lockset
IN120 WiFi
Installation Instructions
FM354 04/16
Attention Installer
Please read these instructions carefully to prevent missing important steps.
Please Note: Improper installations may result in damage to the lock and void the factory warranty.
Important: The accuracy of the door preparation is critical for proper functioning and security of this lock.
Misalignment can cause premature wear and a lessening of security.
For Technical Assistance call Corbin Russwin at 1-800-810-WIRE (9473)
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
IN120 Cylindrical Lock
Table of Contents
1) Warning.................................................................................2
2) General Description..............................................................3
3) Specifications / Features.....................................................3
4) Product Illustration..............................................................4
5) Installation Instructions.......................................................6
6) Operational Check..............................................................17
1) Warning
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced technician for help
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. This Class B
digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements
d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce
dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
!
To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.
To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling
electronic components:
• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto
the door.
!
• Leave components (reader and controller) protected in their respective anti-static bags until ready for installation
• Do not touch pins, leads or solder connections on the circuit boards
*Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and Corbin Russwin, Inc. makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying
and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all
applicable codes and ratings.
Copyright © 2016 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
2
IN120 Cylindrical Lock
2) General Description
The Corbin Russwin IN120 WiFi lock offers the ease and flexibility of WiFi in a streamlined design, setting a new standard
for aesthetics and performance. The IN120 uses IEEE 802.11 WiFi communication and a flexible feature set for easier,
more cost-effective installations, allowing facilities to leverage their IT infrastructure to expand access control coverage to
more doors. Featuring HID® multiCLASS SE® technology, it supports heightened identity security and multiple credentials,
including NFC-enabled mobile phones.
This product is operated by six (6) “AA” alkaline batteries, or can be hard-powered using an optional 9-24VDC power
supply connected by a harness through the door.
Corbin Russwin cylindrical locks are designed with quality components to provide high security, performance and durability.
3) Specifications / Features
Hardware Specifications
• Latch – Stainless steel, ½” (13mm) throw
Optional: ¾” (19mm) throw deadlocking fire latch for pairs of doors
• Deadlocking latch prevents manipulation when door closed
• Door Thickness – 1-3/4” (44mm) to 2” (50mm) Standard
Optional 2” (50mm) to 2-1/4” (57mm) optional
• Outside lever controlled by any combination of contactless reader or mechanical cylinder
• Inside lever retracts latch
• May be used for indoor and outdoor applications
• ANSI/BHMA A156.25 Listed Grade 1 Compliant
NOTE: A weather-protective gasket is required for outdoor applications.
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
3
IN120 Cylindrical Lock
3) Specifications / Features (Continued)
Electrical Specifications:
• HID® multiCLASS SE® technology offers support for
the following credentials:
•
2.4 GHz credential compatibility:
• Secure Identity Object™ (SIO) on Mobile
IDs (Bluetooth Smart)
•
13.56 MHz credential compatibility:
•
• WiFi (IEEE 802.11 b/g/n)
• Multiple time zone and holiday access scheduling
• First-in unlock or automatic unlock configuration,
based on specified time schedule
• Support for most advanced wireless encryption
and authentication standards such as WEP, WPA,
WPA2 and 802.1x*
•
iCLASS®
•
iCLASS SE® (SIO-enabled)
• 2,400 users per lock; 10,000 event audit trail
•
iCLASS Seos
• Privacy button
•
SIO on MIFARE® Classic
•
SIO on MIFARE® DESfire® EV1
• 8200 lock body offers monitoring of deadbolt REX
and provides integrated monitoring of door position
•
MIFARE® Classic
•
DESfire® EV1
•
NFC-enabled mobile phones
®
Power requirements:
•
Alkaline AA Batteries: 9V, 300mA
•
Optional Hard Power (UL294 Listed Power
Supply Required): 9-24VDC, 300mA
125 kHz credential compatibilty:
• UL Listed - UL 294 Indoor Use
•
• CUL Listed - S319: Class 1
HID Prox®
• UL 294 Access Control Ratings:
*For specific security information, please contact your local
ASSA ABLOY Door Security Solutions sales consultant or
call 800-810-WIRE.
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
4
Destructive Attack
Level 1
Line Security
Level 1
Endurance
Level 4
Standby Power
Level 1
IN120 Cylindrical Lock
4) Product Illustration
2
1
3
4
5
Reader Module
ITEM
PART NUMBER/ORDER STRING
DESCRIPTION
COLOR/TRIM
1*
IN-120-EM01-[B]IP-B
HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE®
SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones
Black
QTY
1
IN-120-EM01-[B]IP-W
HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE®
SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones
White
1
IN-120-EM01-[B]IP-MB-[finish]**
HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE®
SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones
Black with metal trim
1
IN-120-EM01-[B]IP-MW-[finish]**
HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE®
SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones
White with metal trim
1
IN-120-EM01-[B]IPS-B
All credentials supported by the IP option plus MIFARE Classic and DESfire EV1
Black
1
IN-120-EM01-[B]IPS-W
All credentials supported by the IP option plus MIFARE Classic and DESfire EV1
White
1
IN-120-EM01-[B]IPS-MB-[finish]**
All credentials supported by the IP option plus MIFARE Classic and DESfire EV1
Black with metal trim
1
IN-120-EM01-[B]IPS-MW-[finish]**
All credentials supported by the IP option plus MIFARE Classic and DESfire EV1
White with metal trim
1
IN-120-EM01-[B]CP-B
FeliCa, HID Prox , NFC-enabled mobile phones
Black
1
®
IN-120-EM01-[B]CP-W
FeliCa, HID Prox , NFC-enabled mobile phones
White
1
IN-120-EM01-[B]CP-MB-[finish]**
FeliCa, HID Prox®, NFC-enabled mobile phones
Black with metal trim
1
IN-120-EM01-[B]CP-MW-[finish]**
FeliCa, HID Prox , NFC-enabled mobile phones
White with metal trim
1
®
®
2
782F718
Inside Mounting Kit (mounting plate & hardware)
1
3
783F519
WiFi Controller
1
4
N/A
AA battery
6
5
782F729
Inside Escutcheon
Black
782F739
Inside Escutcheon
White
783F725 FIN**
Inside Escutcheon
Black with metal trim
783F735 FIN**
Inside Escutcheon
White with metal trim
1
6
FM355
Field prep template (not shown)
1
7
T31202
Door manufacturers template (not shown)
1
--
FM354
Instructions (this manual)
1
*Specifying B indicates BLE (Bluetooth) option when ordering
**Specify finish
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
5
IN120 Cylindrical Lock
4) Product Illustration (Continued)
Tools Required:
• Phillips Screw Driver #2, #3
• Flat Blade Screw Driver (Standard size)
• 1/8” Security Allen Wrench
• 7/64” Allen Wrench (supplied)
• T20 Security torx driver (supplied)
4
2
3
1
1
783F918
CL33134 Cylindrical lock with fixed core cylinder
1
783F928
CL33134 Cylindrical lock with removable core cylinder
2
783F889
Inside Spring Cassette - IN120 REX
1
3
682F268
Outside Spring Cassette (1-3/4” - 2” Door)
1
682F278
Outside Spring Cassette (2” - 2-1/4” Door)
783F619
DPS (Door Position Switch) Kit
4
For parts not listed, refer to CL3300 Parts and Service Manual
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
6
1
IN120 Cylindrical Lock
5) Installation Instructions
1. Verify Hand and Bevel of door
Illustrations shown are as viewed from the outside or secure side of opening.
Left Hand
Hinges Left.
Open Inward.
“LH”
2. Left Hand
Reverse Bevel
Hinges Left.
Open Outward
“LHRB”
Right Hand
Hinges Right.
Open Inward.
“RH”
Right Hand
Reverse Bevel
Hinges Right.
Open Outward
“RHRB”
Door Preparation
Prep door according to supplied door marker (FM356). For door manufacturer templates
visit www.corbinrusswin.com and reference template # T31203.
Wood Door
shown
Fig. 1
Outside Face of Door
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
Inside Face of Door
7
IN120 Cylindrical Lock
5) Installation Instructions (Continued)
3. Install Door Position Switch (DPS)
a. Insert DPS into the raceway on the latch edge of the door.
b. Push wires through raceway toward lock prep.
c. Push DPS firmly into place by hand.
Note: DO NOT TAP SWITCH WITH ANY TOOL.
d. Install magnet into door frame. Push firmly into place by hand.
See instruction A7983.
CAUTION: if DPS is not installed or is installed
improperly, door status monitoring features will
not function.
Fig. 2
4.
Install Latch Bolt
Install latch bolt with beveled bolt facing the strike
using two #8 x 3/4” combination screws (Fig. 3):
Fig. 3
5.
Install Strike Plate
Install Strike Plate using two #12 x 1” combination
screws (Fig. 4):
Optional Strike Box
Fig. 4
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
8
IN120 Cylindrical Lock
5) Installation Instructions (Continued)
6.
Install Lock Body
a. Feed lock body and wire through 2-1/8” diameter hole from outside of door (Fig. 5a).
Be sure latch engages lock body as shown (Fig. 5b).
b. Connect 4-pin connector from lock body to 4-pin on
cassette (Fig. 5c).
Outside Face of Door
Fig. 5b
Fig. 5a
c. Temporarily install top throughbolt to hold chassis in door (Fig. 5c).
Important: Door must remain open during installation.
Use door stop.
Inside Face of Door
Spring Cassette
Fig. 5c
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
9
IN120 Cylindrical Lock
5) Installation Instructions (Continued)
7.
Install Inside Spring Cassette Lock
a. Feed harness wires and ground wire up through raceway (Fig. 6a).
b. Remove screw from previous step.
c. Slide on cassette and secure with (2) screws.
Remove Screw
Fig. 6a
Fig. 6b
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
10
Spring Cassette
IN120 Cylindrical Lock
5) Installation Instructions (Continued)
8.
Installation and Removal of Lever and Standard Cylinder
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
11
IN120 Cylindrical Lock
5) Installation Instructions (Continued)
9.
Install Outside (Reader) Escutcheon
a. Orient the reader so the LED lens is at the top.
b. Feed the reader harness through the door (from outside to inside).
c. Install the reader to the outside of door by aligning the mounting posts with the door preparation holes.
Hold the reader flush against door while ensuring proper alignment.
Outside Face
of Door
LED
Reader Assembly
with Harness
Fig. 8a
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
12
IN120 Cylindrical Lock
5) Installation Instructions (Continued)
9.
Install Outside (Reader) Escutcheon - (Continued)
d. Next feed the cables/connectors through the inside mounting assembly (and gasket if required*).
Inside of Door
NOTE: Cable lengths exaggerated for illustrative purposes.
Gasket*
Mounting Plate
Through bolt
DPS
Reader Harness
Lock body Harness
Through bolt
Ground Lug
e. When all connections have been made, tuck ferrite bead and excess cable into wire hole on inside of door.
Fig. 8b
f. Secure the mounting assembly while ensuring proper alignment of outside reader and tighten the (2) through-bolts on the inside of the door to secure the reader (Fig. 16c).
*Gasket is required for outdoor installations.
If installing with gasket; separate gasket from mounting plate to feed cables/connectors
through holes as indicated (Fig. 8b).
Once cables/connectors are fed through, reattach gasket to mounting plate.
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
13
IN120 Cylindrical Lock
5) Installation Instructions (Continued)
10.
Installation of Connectors
DPS (4-pin)
Installation of Connectors
A
CAUTION - Do not touch or allow debris to enter connector contacts.
12-24VDC
Power*
Secure the following connectors to their respective terminals (Fig. 9a ):
A. Secure the 4-pin DPS connector.
B. Secure the 10-pin lock body assembly connector.
B
Ground
Anchor
C. Secure ground lug to #6-32 machine screw.
*NOTE: Optional 2-pin external 12-24VDC power connector.
C
IMPORTANT: Do not run wires through hole in plate (Fig. 9c) - this will damage wires and the controller connector.
Fig. 9a
Route wires around flange, do not route wires through the flange hole (Fig. 9c,d).
Inside
Face of
Door
Fig. 9c
D. Secure the 24-pin card reader connector (Fig. 9d).
Reader
(24-pin)
Board-to-Board
Connector
Fig. 9d
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
Fig. 9b
14
Lock
Body
(10-pin)
IN120 Cylindrical Lock
5) Installation Instructions (Continued)
11.
Install Inside Module Component Assembly
1. Insert top tabs of controller into slots on mounting plate (Fig. 10).
2. Ensure proper alignment of board-to-board connectors while pivoting bottom of controller toward door until tab on bottom snaps securely into place on mounting plate.
CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller.
Fig. 10
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
15
IN120 Cylindrical Lock
5) Installation Instructions (Continued)
12.
Battery Installation
Before installing batteries for the first time:
Remove pull tab from its position beneath the coin cell by pulling
on tab in direction of arrows printed on tab (Fig. 11).
a. Place (6) “AA” alkaline batteries in the compartment, being careful to align polarity properly.
b. After batteries are installed, there is a slight delay; then an
audible “beep” will sound and the lock motor will cycle.
Pull Tab
Fig. 11
13.
Inside Cover Installation
Inside
Cover
a. Assemble cover by hooking top edge on inside
mounting plate.
b. Carefully press bottom of cover toward door without pinching any wires.
c. Secure cover utilizing security allen wrench.
Security Allen
Screw
Fig. 12
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
16
IN120 Cylindrical Lock
6) Operational Check
When lock is fully installed, perform the following steps:
a. Insert key into cylinder and rotate (Fig. 13a).
b. There should be no friction against lock case, wire harness or any other obstructions.
c. Check that the key retracts the latch.
d. The key should rotate freely.
e. Try the inside lever; ensure it retracts latch.
f. Use a valid credential* set up with the Lock Configuration Tool to
unlock outside lever and retract latch.
Refer to Network and Lock Configuration
Tool user manual (WFMN1) for information on
how to configure and program locks.
*Twenty (20) seconds after lock initialization
(single beep with lock motor actuation).
Fig. 13a
Note: The credential should approach the inscription on the reader as indicated (Fig. 13b) to ensure that the credential is read properly.
Do not wave credential.
Fig. 13b
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
17
IN120 Cylindrical Lock
Notes
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
18
Copyright © 2016 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising