Carbon Monoxide (CO) Digital LON Gas Transmitters

Carbon Monoxide (CO) Digital LON Gas Transmitters
Carbon Monoxide (CO) Digital LON Gas Transmitters
DESCRIPTION
PolyGard
DT-1110 V1
Digital LON gas transmitters for the detection of carbon monoxide (CO) in
the ambient air for direct link to LONWORKS® network.
APPLICATION
To sense carbon monoxide (CO) in a wide variety of commercial and
industrial applications such as vehicle exhaust in parking structures, engine
repair shops, tunnels, equipment rooms and ventilation systems, etc. and
transmit to any compatible interoperable LON-bus system.
FEATURES
LONWORKS® interfacing
LONWORKS® functional profile
Continuous monitoring
Easy plug-in sensor
Electrochemical gas sensor,
gas specific, long-life
• Temperature compensated
•
•
•
•
•
• 4-20 mA input from remote
analog transmitter
• Polarity protected
• Overload & short circuit protected
• RFI/EMI protected
• Modular plug-in technology
• Easy maintenance
City of Los Angeles
Approved
SPECIFICATIONS
Electrical
Power supply
Power consumption
RFI/EMI protection
Sensor Performance
Gas detected
Sensor element
Range
Resolution
Repeatability
Long term output drift
Response time
Sensor life expectancy
Sensor coverage
Installation Location
Mounting height
Type of Control
General
LONWORKS®
- transceiver
10-28 VDC, polarity protected
28 mA (0.7 VA)
5.0 W @ 1 ft. (0.31 m) radiated
Carbon monoxide (CO)
Electrochemical, diffusion
0-300 ppm, factory set
± 3 ppm of reading
± 3% of reading
< 0.4% signal loss/month
t90  50 sec.
5 years, normal operating
environment
5,000 sq.ft., max. 10,000 sq.ft.
(465 m², max. 930 m²),
under “ideal conditions”
5 to 6 ft. (1.5 to 1.8 m) above floor
Continuous proportional sensor
signal
Standard network variables
SNVTs according LONMARK®
application layer, Interoperability
directives, version 3.2
FTT-10A
AT series remote gas
transmitter input capability
- analog input
- power output
Environmental
Permissible ambient
- working temperature
- storage temperature
- humidity, continuous
- humidity, intermitted
- working pressure
Physical
Enclosure, standard
- material
- color
- protection
- installation
Dimensions (H x W x D)
Cable entry
(1) 4-20 mA, overload and short
circuit protected
24 VDC, max. load 100 mA
14°F to 122°F (-10°C to 50°C)
41°F to 86°F (5°C to 30°C)
15 to 90% RH, non-condensing
0 to 99% RH, non-condensing
Atmospheric ± 10%
Galvanized steel w/zinc coating,
corrosion resistant
Light gray
NEMA 1 (IP 42), general purpose
Wall (surface) mounted, or
single gang electrical box
5.59 x 5.59 x 2.48 in.
(142 x 142 x 63 mm)
1 hole for 1/2 in. conduit for wall
(surface) mounting, and
1 hole on back side of base plate
for single gang electrical box
mounting
LONWORKS®, LONMARK® and ECHELON are registered Trademarks of Echelon Corporation
Customer Services (858) 578-7887 & (888) GO INTEC
Fax (858) 578-4633 & (888) FX INTEC
INTEC Controls, 12700 Stowe Dr. Suite 110, Poway, CA 92064
www.inteccontrols.com
Specification subject to change without notice.
Page 1 of 4
Printed in USA 100513
DT-1110 V1
SPECIFICATIONS
Physical (cont...)
Wire connection
Wire size
Weight
Approvals/Listings
- sensor element
- unit rating
Warranty
OPTIONS
Enclosures
Duct mounted “1”
- w/probe
Terminal blocks,
screw type for lead wire
Min. 24 AWG (0.25 mm²),
Max. 14 AWG (2.5 mm²)
0.7 lbs. (0.3 kg)
NEMA 3 (IP45)
7/8 in. (22 mm) diameter and
7.16 in. (182 mm) length
1 hole for 1/2 in. conduit
NEMA 12 (IP55)
Polycarbonate,
UL 94-HB, fire-retardant
UL 50
Light gray
Wall (surface) mounted, or
single gang electrical box
5.12 x 3.70 x 2.25 in.
(130 x 94 x 57 mm)
1 hole for 1/2 in. conduit for wall
(surface) mounting, and
1 hole on back side of base plate
for single gang electrical box
mounting
UL Listed, E208470
CSA Certified, E208470
NEMA 4X (IP65)
Polycarbonate,
UL 94-HB, fire-retardant
UL 50
Light gray
Special moisture filter protection
Wall (surface) mount
5.12 x 5.12 x 2.95 in.
(130 x 130 x 75 mm)
(1) PG 13.5 compression fitting,
removeable, hole fits 1/2 in.
conduit conductor
UL Listed, E208470
CSA Certified, E208470
NEMA 4X, (IP65) w/splash guard
ABS UL94 V0
Light gray
Wall (surface) mount
4.80 x 4.72 x 3.42 in.
(122 x 120 x 87 mm)
(1) PG 13.5 compression fitting,
removeable, hole fits 1/2 in.
conduit conductor
For low temperature environment
-40°F (-40°C)
24 VAC/VDC ± 5%, 50/60 Hz
1.0 A (24 VA), max.
32°F (0°C) ± 5°F (3°C)
- cable entry
Wall mounted “A”
- material
UL Recognized CO Sensor
City of Los Angeles
CE
Conformity according LONMARK®
Interoperability Association
VDI 2053, air treatment systems
for garages and tunnels
EMV-Compliance 89/336/EWG,
low voltage directives 73/23/EWG
Two years material and
workmanship
- conformity
- color
- installation
- dimensions (H x W x D)
- cable entry
- enclosure approval
Wall mounted “C”
- material
-
conformity
color
gas inlet
installation
dimensions (H x W x D)
- cable entry
- enclosure approval
ORDERING INFORMATION
Wall mounted “4”
- material
- color
- installation
- dimensions (H x W x D)
DT-1110 - 0 - 010 - 0
- cable entry
(Product label “DT-1110-x-x10-0 V1”)
Heater, built-in
Ambient temperature
Power supply
Power consumption
Thermostatic control
Enclosures
0
1
A
C
4
Wall, NEMA 1
Duct, NEMA 3
Wall, NEMA 12
Wall, NEMA 4X
Wall, NEMA 4X
w/splash guard
0 = Standard enclosure
Options
010
500
LON Interoperability mode
Heater
Range
0
0-300 ppm CO
010 = Standard,
LON Interoperability mode
LONWORKS®, LONMARK® and ECHELON are registered Trademarks of Echelon Corporation
Customer Services (858) 578-7887 & (888) GO INTEC
Fax (858) 578-4633 & (888) FX INTEC
INTEC Controls, 12700 Stowe Dr. Suite 110, Poway, CA 92064
www.inteccontrols.com
Specification subject to change without notice.
Page 2 of 4
Printed in USA 100513
DT-1110 V1
WIRING CONFIGURATION
DT-1110
Terminal 7:
Enclosure to ground
Terminal 5 & 6: Cable shield connection
X4
7
6
5
4
3
2
1
DT-1110 w/heater
Shield
X5
Shield
1
A
2
B
LONWORKS®
(–)
(+)
(–)
(+)
24 VDC Power output
for (1) remote analog
transmitter
24 VDC Power input
for DT-1110
3
4
4-20 mA
signal input
5
X1
Must use a separate
power supply of
24 VAC/VDC
(+)
2
COM
1
LONMARK®, PRODUCT DETAILS
Product data sheet
Device category
Communicaton
LONMARK® version
PolyGard digital transmitter DT
Gas Concentration
TP/FT-10
3.2
LONMARK® object
Download files
Standard program ID
Certificates
0000 - Node object
0001 - Open loop sensor object
0002 - Open loop sensor object
8000230A50060402.zip
XIF (external interface file)
8000230A50060402
TÜV, VDI 2053
LONWORKS®, LONMARK® and ECHELON are registered Trademarks of Echelon Corporation
Customer Services (858) 578-7887 & (888) GO INTEC
Fax (858) 578-4633 & (888) FX INTEC
INTEC Controls, 12700 Stowe Dr. Suite 110, Poway, CA 92064
www.inteccontrols.com
Specification subject to change without notice.
Page 3 of 4
Printed in USA 100513
DT-1110 V1
Standard Network and Configuration Variables
The DT-1110 LON gas transmitters are for direct link to
L ON W ORKS ® network. The transmitter functions are made
available to the LONWORKS® network as standard network
variables according to LONMARK®.
LONWORKS®, LONMARK® and ECHELON are registered Trademarks of Echelon Corporation
Customer Services (858) 578-7887 & (888) GO INTEC
Fax (858) 578-4633 & (888) FX INTEC
INTEC Controls, 12700 Stowe Dr. Suite 110, Poway, CA 92064
www.inteccontrols.com
Specification subject to change without notice.
Page 4 of 4
Printed in USA 100513
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising