Tuzio® Ancona Towel Warmer

Tuzio® Ancona Towel Warmer
Tuzio® Ancona
Towel Warmer
Installation Guide
Code: W9204
23.5” x 37.5” Hardwired
Technical Helpline:
Toll-Free 1-877-757-8990
www.icocanada.com
Towel Warmer Installation Procedure
1 Rough-in Requirements
(see figure 3)
1. The incoming power feed goes to a deep single gang electrical box (for timer). This electrical box can be located
anywhere in the room, although we recommend it be alongside your light switches.
2. A power feed then goes from the timer electrical box to a single gang electrical box (for Towel Warmer). The location
of this electrical box governs the location of your Towel Warmer (see fig. 2).
3. Wall studs or plywood backing is required in the wall at all bracket locations. See figure 2 for bracket locations.
2 Installation Instructions
(see figure 1)
1. Check all items have been received. You should have Towel Warmer, hardwire kit, programmable timer and mounting
bracket kit. Read all instructions before continuing.
2. Fix wall supports "B" including collar “A” to the wall using the screws provided and in locations as shown on figure 2.
3. Screw the threaded pin "C", into the threaded bushing “D”.
4. Hang and adjust the Towel Warmer using set screws "E" to lock pin "C" in the wall bracket "B". Ensure the Towel
Warmer is firmly and safely fixed.
fig. 1
3 Hardwire Connection
(see figure 4)
Do not connect the Towel Warmer to the power supply until all instructions have been read and installation carried out in
accord with them. The heating element is 150W 110V. The element conforms to UL standards and the unit to CSA
standards (File ref: 229718). Ensure the CSA label is visible. TURN OFF POWER SUPPLY BEFORE PROCEEDING.
1. Feed the electrical cord located at the bottom of the Towel Warmer first through the round tube and then through the
cover plate.
2. Complete all electrical connections as shown in figure 3.
3. Fit tube over Towel Warmer element sleeve until it meets the hexagonal chrome collar.
4. Push cover plate onto tube.
5. Screw cover plate to electric box with the enclosed screws. Adjust where necessary.
Warning: In case of damage or failure of the Towel Warmer the unit should be returned to the
manufacturer or their distributor. The warranty of 1 year on the heating element and 5 years
on the Towel Warmer is NOT VALID in case of improper use or installation. Product is
designed for use within Canada and the United States only.
Specifications & Drawings
Model #
W9204
Description
Ancona Electric Hardwire
Finish
Brushed
Nickel
Weight (lb) Element Size
25.7
150W
Output
WxH (mm)
WxH (Inches)
Metal Type
1228Btu
600 x 950
23.5” x 37.5”
Stainless
Steel
Heating Element Specifications: 150 watt, 12" long, 120 volt, 60 Htz, IP55 cord, ULC approved
Material Specifications: Mild Steel - Din 2394 Quality - ST 34-2 KB / Stainless Steel - Din 17457 Quality - 1.4301
Warranty: Towel Warmer: 5 years, Heating Element: 1 year, Programmable Timer: 2 years
Fixings: Screws, and Allen Key (if needed) are included
Heating Element Location: Right-hand vertical column unless specified otherwise.
Care & Maintenance: A periodic wash using warm water and a soft cloth will retain the high quality finish of your towel warmer for
many years to come. ON NO ACCOUNT should any household bleaches, detergents, abrasive polishes, steel wool or other cleaning
agents be used on this item.
fig. 2
fig. 4
fig. 3
fig. 4
Timer Installation Procedure
1 Installation
1
2
Install the timer as shown in figure 3.
Apply power at the circuit breaker.
5 Programming
You can set up to 7 programs. To set a program, you need to
enter its start time (ON) and its end time (OFF).
1
2 Power On
2
1 Pry the switch door open from the
bottom using a small screwdriver.
2 Ensure the ON/OFF selector is set
to ON.
Reset
the switch using a
3
paperclip. 0:00 and MO will flash.
3 Setting the Clock
1
Set the time using the HOUR and MIN buttons.
Set the day by using the DAY button.
3 Press one of the control buttons or close the switch door
to return to normal operation.
3
4
5
2
6
7
4 Selecting the Operating Mode
The programmable switch has 2 operating modes: manual
(MAN) and automatic (AUTO). To switch mode, press the timer
door for 3 seconds.
Manual Mode
The programmable timer operates as a regular
switch. Briefly press the switch door to turn the
towel warmer On or Off. The mode (MAN) and
state (ON or OFF) are displayed.
Automatic Mode
The programmable timer follows the
programmed schedule. The mode (AUTO),
state (ON or OFF) and current program
number are displayed. To temporarily override
the programmed schedule, briefly press the
switch door. The new state (ON or OFF) will flash to show that
this state is temporary. The override remains in effect until you
press the timer door again or until the beginning of the next
program.
8
Pry the timer door open using a small screwdriver.
Press the PGM button to display a
program and its On or Off time. For
example, when you first press PGM,
program number 1 (P1) and its On time
(ON) will appear. -:-- will appear instead
of the time if the program is not set (inactive).
Press the DAY button to select the day
to which you want to apply the program.
NOTE: If you want to apply the program
to every day of the week, press DAY
until all the days are displayed. (This
still counts as 1 program, not 7)
Press the HOUR and MIN buttons to set the ON time
(time when you want the towel warmer to turn on)
After you have programmed the ON time, press the PGM
button to display the OFF time (time when you want the
towel warmer to turn off).
Repeat steps 3 through 5 to program
the OFF time. If the program ON time is
set for every day of the week, the
program OFF time will automatically be
set for every day.
To set another program, repeat steps 2 through 6.
Programs that are not set will remain inactive.
Press one of the control buttons or close the timer door
to return to normal operation.
Clearing a Program
Press the PGM button until the desired program is selected.
Hold the PGM button for 3 seconds. -:-- appears when the
program is erased.
6 Troubleshooting
Blank display
• Verify circuit breaker at main
panel.
• Ensure the ON/OFF selector is at
ON.
• Reset the switch using a paper
clip.
Programs do not run
as expected
• Make sure the switch is properly
programmed.
• Note that -:-- indicates an inactive
program, 00:00 indicates
midnight.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising