Bluetooth Clock Radio with Cellphone Holder

Bluetooth Clock Radio with Cellphone Holder
Bluetooth Clock Radio with Cellphone Holder
USER MANUAL
JCR-295
PLEASE READ THIS OPERATION MANUAL COMPLETELY BEFORE OPERATING
THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
CAUTION
Follow the advice below for safe operations.
Stop operation immediately if any liquid or solid object should fall into the cabinet.
If the unit is not to be used for a long period of time, make sure that all power sources
are disconnected from the unit. Remove all batteries from the battery compartment,
and unplug the AC-DC adaptor from the wall outlet. Make it a practice to remove the
AC-DC adaptor by grasping the plug and not by pulling the cord.
ON PLACEMENT
Do not use the unit in places, which are extremely hot, cold, dusty or humid.
Place the unit on a flat and even surface.
Do not restrict the airflow of the unit by placing it in a place with poor ventilation, by
covering it with a cloth or by placing it on a carpet.
ON CONDENSATION
When left in a heated room where it is warm and damp, water droplets or
condensation may form inside the unit.
When there is condensation inside the unit, the unit may not function normally.
Let it stands for 1 to 2 hours before turning the power on, or gradually heat the room
up and dry the unit before use.
Should any trouble occur, remove the power source and refer servicing to qualified
personnel.
COMPLIANCE WITH FCC REGULATIONS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
E-1
PROTECT YOUR FURNITURE!!
This system is equipped with non-skid rubber ‘feet’ to prevent the product from moving
when you operate the controls. These ‘feet’ are made from non-migrating rubber
material specially formulated to avoid leaving any marks or stains on your furniture.
However certain types of oil based furniture polishes, wood preservatives, or cleaning
sprays may cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on the
furniture.
To prevent any damage to your furniture we strongly recommend that you purchase
small self-adhesive felt pads, available at hardware stores and home improvement
center severywhere, and apply these pads to the bottom ofthe rubber ‘feet’ before you
place the product on fine wooden furniture.
DEAR JENSEN® CUSTOMER
Selecting fine audio equipment such as the unit you've just purchased is only the start
of your musical enjoyment. Now it's time to consider how you can maximize the fun and
excitement your equipment offers. This manufacturer and the Electronic
Industries Association's Consumer Electronics Group want you toget the most out
of your equipment by playing it at a safe level. One that lets the sound come through loud
and clear with out annoying blaring or distortion and, most importantly, without
affecting your sensitive hearing. Sound can be deceiving. Over time your
hearing "comfort level" adapts to higher volumes of sound. So what sounds "normal" can
actually be loud and harmful to your hearing. Guard against this by setting your
equipment at a safe level BEFORE your hearing adapts.
To establish a safe l evel:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
• Once you have established a comfortable sound level: Set the dial and leave it
there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
We Want You Listening For a Lifetime
Used wisely, your new sound equipment will provide a
lifetime of fun and enjoyment. Since hearing damage
from loud noise is often undetectable until it is too
late, this manufacturer
and the Electronic Industries
Association's Consumer Electronics Group recommend
you avoid prolonged exposure to excessive noise.
Customer's Record:
The serial number of this product is found on its bottom cover. You should note the serial
number of this unit in the space provided as a permanent record of your purchase to aid
in identification in the event of theft of loss.
Model Number : JCR-295
Serial Number :
E-2
LOCATION OF CONTROLS
8
9
1
2
10
11
3
USB CHARGING
12
4
13
5
6
14
15
7
16
17
18
19 20
SLEEP indicator
PM indicator
DISPLAY INDICATOR
Wake to BUZZER
Wake to BUZZER
ALARM 1
WAKE UP SOURCE indicator
ALARM 2
WAKE UP SOURCE indicator
Wake to RADIO
Wake to RADIO
BLUETOOTH indicator
1.
PM INDICATOR
11.
2.
ALARM 1 WAKE TO
ALARM/RADIO INDICATORS
ALARM 2 WAKE TO
ALARM/RADIO INDICATORS
12.
ALARM 1 / ALARM 2 BUTTONS
13.
PAIRING / PLAY / PAUSE
BUTTON
3.
BLUETOOTH INDICATOR
4.
PRESET/TIME BUTTON
14.
DIMMER BUTTON
5.
POWER / FUNCTION BUTTON
15.
VOLUME +/- BUTTONS
6.
TUN-/MIN/
16.
SNOOZE / SLEEP BUTTON
/ TUN+/HR/
BUTTONS
7.
BATTERY COMPARTMENT
8.
CELLPHONE HOLDER
9.
LED DISPLAY
10.
SLEEP INDICATOR
E-3
17.
AUX IN JACK
18.
USB JACK ( for USB charging )
19.
DC JACK
20.
FM ANTENNA
POWER SOURCE (AC ADAPTER ONLY)
The JCR-295 operates with an external AC-DC adaptor with a rating of DC 5V, 1200mA .
The system is also equipped with a battery back-up system for the clock that is powered by 2
pieces of “AAA” (UM-4) size batteries (Not included).
Note : The batteries may be installed as a backup option to maintain the clock time if electrical
power fails. In the event of power outage, the clock time will not be displayed, however
the clock will continue to operate so current time will be maintained.
AC OPERATION
The JCR-295 only operates using the AC-DC adaptor. Be sure to use an AC-DC adapter
with a rating of DC 5V, 1200 mA and with the following polarity:
If you are using a universal adaptor with an output polarity switch or polarized plugs, be
sure to set the polarity of the center plug to "+".
WARNING : Never use this radio near water or in the shower when using an AC adaptor.
Shock or personal injury could occur.
INTALL BACKUP BATTERIES
1. Remove the Battery Door on the bottom of the unit.
2. Following the polarity diagram as shown inside the battery compartment (#7), insert 2
AAA size batteries (not included ) and replace the door.
IMPORTANT:
Be sure that the batteries are installed correctly. Wrong polarity may damage the unit.
1.
Only an adult should replace the batteries.
2.
Use only the size and type of batteries specified.
3.
For better performance and longer operating time, we recommend the use of
alkaline-type batteries.
4.
Do not mix old and new batteries.
5.
Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries.
6.
If the unit is not to be used for an extended period of time, remove the batteries.
7.
Old or leaking batteries can cause damage to the unit and may void the warranty.
8.
Do not dispose of batteries in fire, batteries may leak or explode.
9.
Do not try to recharge batteries not intended to be recharged, they can overheat and
rupture. (Follow battery manufacturer’s directions.)
E-4
SETTING THECLOCK TIME
In order for the clock to function properly, the clock has to be set before you use it for the
first time. After powering up the unit or press and hold PRESET/TIME Button (#4) at
standby mode, the clock display will flash. To set the time, follow the steps below:
1. Tap the TUN-/MIN/
/ TUN+/HR/
Buttons (#6) until the correct time is
displayed..
2. Press the PRESET/TIME Button (#4) to confirm the time.
Note:
1. Make sure the hour is set so that AM or PM is correctly displayed. There is a PM
Indicator (#1) located in the upper left corner of the LED display (#9). If the PM
Indicator (#1) is showing on the display, the displayed time is “PM”. If the PM Indicator
(#1) is not showing on the display, the time displayed is “AM”.
2. The two dots between the Hour and Minute digits keep flashing at Standby Mode and
light steadily when in On (RADIO, BLUETOOTH or AUX ) mode.
RADIO OPERATION
Press the POWER/FUNCTION Button (#5) repeatedly to Turn On the unit and select Radio
Mode, frequency will show on the LED display (#9).
Press and hold the TUN-/MIN/
OR TUN+/HR/
Buttons (#6) to search for the next /
previous available station. If the reception is poor, try Manual Tuning to fine-tune the
station. Press the TUN-/MIN/
OR TUN+/HR/
Buttons (#6) briefly to manually tune
through the frequency band.
Adjust the VOLUME +/- Control (#15) to obtain the desired sound level.
The LED display will change to show the clock time after a few seconds. Press the
OR TUN+/HR/
Buttons (#6) to check the tuned frequency.
TUN-/MIN/
Setting the Radio Station Presets
The unit allows you to store up to 20 stations for easy recall at any time.
1. Tune to the radio station you want to store in memory.
2. Press and hold the PRESET/TIME Button (#4). The preset channel number “P01” will
be flashing on display.
OR
3. To change the preset channel number location, press the TUN-/MIN/
TUN+/HR/
Buttons (#6) to step through the preset locations ( P01 – P20 ).
4. To confirm the preset location, press PRESET/TIME Button (#4).
5. To store up to 20 station presets, repeat steps 1-4 above.
RECALL PRESET STATION
In Radio mode, press PRESET/TIME Button (#4) repeatedly to select the preset channel.
TIPS FOR BEST RADIO RECEPTION
To insure maximum FM tuner reception, unwrap and fully extend the EXTERNAL FM
WIRE ANTENNA (#24) for best FM radio reception.
E-5
BLUETOOTH OPERATION
Pairing a Bluetooth enabled device with the JCR-295.
1. Press the POWER/FUNCTION Button (#5) repeatedly to turn on unit and select
Bluetooth mode, “bt” will show on the LED Display (#9). The
INDICATOR (#3) will
flash.
2. Turn on the Bluetooth function for the device you want to link to, and enable the search
or scan function to find the JCR-295.
3. Select "JCR-295" from the device list when it appears on your device screen. If required,
enter the pass code “0000” to pair (link) JCR-295 with your device.
4. If you are pairing (linking) your computer to the speaker using Bluetooth, you may need
to set the JCR-295 as your computer’s default sound device.
5. After successfully pairing the JCR-295 with your Bluetooth device, The
(#3)) will stop flashing and remain lit.
INDICATOR
6. If you want to pair (link) the JCR-295 with another Bluetooth device, press and hold
Button (#13) a few seconds. The
Pairing/Play/Pause/
INDICATOR (#3) will flash.
The JCR-295 will go into Pairing/Discoverable mode. Repeat steps 2 & 3.
Now you can play music from your Bluetooth device wirelessly to the JCR-295.
Button on your Bluetooth
1. Selecting your favorite song, press the Play/Pause/
Button (#13) on the JCR-295 to play or pause the
device or the Pairing/Play/Pause/
the song from your Bluetooth device.
2. Press Skip Forward
Button or Skip Backward
Button (#6) to select the
Next or Previous track.
( The SEARCH function does not apply to Bluetooth operation )
3. Press VOLUME +/- buttons (#15) of your JCR-295 and your Bluetooth device until you
reach a comfortable listening level.
Note :
1. Refer to the manual of your cell phone, tablet PC, computer or other Bluetooth
enabled devices for Bluetooth operation since it may vary from model to model.
2. If your Bluetooth enabled device does not support A2DP profile, it will not play the
music through the speaker, even if paired (linked).
3. Remember to turn off the JCR-295 when you have finished listening, press and hold
POWER/FUNCTION button (#5) a few seconds to turn off the unit.
4. Don't forget to switch off the power of your external audio device as well.
5. The music playback will automatically be paused when you have an incoming call.
When the call is ended the JCR-295 will start playing again
E-6
ALARM OPERATION
SETTING THE ALARM TIME
You can set two different alarm times and select wake to RADIO / ALARM sound.
1. In standby mode, press and hold the ALARM 1 Button (#12) until the LED display
flash.
2. Press the MIN / HR Buttons (#6) to set the hour and minute of the alarm time.
3. Press the ALARM 1 Button (#12) to confirm the alarm time. LED display resume display
the current time.
4. Alarm 2 setting procedures are same as Alarm 1.
Note : If Alarm 1 and Alarm 2 set at same time, only Alarm 2 will function.
SETTING WAKE TO ALARM OR RADIO
1. In standby mode, press the ALARM 1 Button (#12) repeatedly to set alarm 1
a. Wake to Alarm, Alarm 1 WAKE to ALARM Indicator (#2) will light up.
b. Wake to Radio, Alarm 1 WAKE to Radio Indicator (#2) will light up.
c. Alarm 1 Off, both WAKE to ALARM & RADIO Indicators light off
2. When alarm sounds, press POWER /FUNCTION Button (#5) once to stop the alarm
and it will repeat next day same time.
3. When alarm sounding after one hour, the sound will auto off and repeat next day.
4. Alarm 2 wake to Alarm or radio setting procedures is same as Alarm 1.
STOP THE ALARM SOUND
When alarm sounds, press POWER/FUNCTION Button (#5) once to stop the alarm and it
will repeat next day same time.
COMPLETELY TO TURN OFF ALARM (NOT RESET FOR NEXT DAY)
In standby mode, press the ALARM 1 / ALARM 2 Buttons (#12) repeatedly until the alarm
wake up ALARM and RADIO indicators (#2 & #11) light off.
CHECKING THE ALARM TIME
In standby mode, press and hold the ALARM 1 or ALARM 2 Button (#12) until the alarm
time shows.
SNOOZE ALARM
After the radio or alarm sounds, you may press the SNOOZE button (#16) for a few
more minutes sleep. The alarm will stop for approximately 9 minutes and then turn on
again.
DIMMER CONTROL
Press the DIMMER Button (#14) briefly to select LED DISPLAY (#9) brightness.
SLEEP FUNCTION
This function allows you to program the system to turn itself OFF after a set period of time. You
can set your sleep time while in Power On ( Radio, AUX or Bluetooth ) mode:
1. To activate the sleep function, press the SLEEP button (#16) repeatedly on the unit, the
display will show “90, 80, 70, 60, 50, 40, 30, 20, 10, OFF in sequence.
2. When the display shows your desired sleep time, release the button, the sleep timer is now
activated, the SLEEP Indicator will Turn On. The display show “10” is to indicate “10 minutes”
sleep time and so on. When the sleep time counts to zero, the unit will go off.
E-7
AUX OPERATION
You can play other music sources (iPod, MP3 or other digital audio players) through the
speakers of the JCR-295 by connecting the AUX IN Jack (#17) to your external player’s
audio out jack or headphone jack.
1. Plug one end of an audio cable (not included) into the AUX IN Jack (#17) and the other
end of the cable to the headphone jack of your digital audio player.
2. Press the POWER/FUNCTION Button (#5) repeatedly to select the AUX mode, LED
Display (#9) show AU.
3. Start playing the device you plugged into the AUX IN Jack (#17).
4. Slowly adjust both the volume controls of the JCR-295 and the external device until
you reach a comfortable listening level.
5. Turn off your iPod, MP3 player etc. when finish listening.
6. Press and hold the POWER/FUNCTION Button (#5) 5 seconds to turn the JCR-295
off and unplug the AUX IN Jack.
Note :
• If you connect the JCR-295 to the Line-Out Jack of your external device, you only
need to adjust the VOLUME CONTROL of your JCR-295. If you connect to the
Headphone Jack of your external device, you may need to adjust both the volume
controls of your external device and the JCR-295 to obtain the desirable listening
level.
• Remember to turn off the JCR-295 when you have finished listening. Don't forget to
switch off the power of your external audio device as well.
USING THE CELL PHONE HOLDER
Cell Phones and Smaller tablets can be placed in the Cell Phone Holder when it is
attached to the top of the JCR-295. Smaller tablets can be placed in vertical or horizontal
mode as shown below.
NOTE: We do not recommend placing larger screen tablets in the Cell Phone Holder.
Larger tablets may cause the JCR-295 to be unstable and it may fall over and cause
damage to the tablet.
OR
OR
E-8
USB BATTERY CHARGING
CONNECTINGA USB CORD (INCLUDED) FOR CHARGING YOUR CELL PHONE
(DC5V,1000MA)
1. Plug the standard end of the USB cable (included) into the USB CHARGING PORT
located on the back of the JCR-295. Plug the other end of the cable into the device you
wish to charge.
2. Observe the battery charge indicator on your device to make sure the charging process
starts normally.
3. Unplug the cable when your device is fully charged.
WARNING!
The USB port located on the back of the JCR-295 is designed for asmart phone or
portable device battery charging only and does notsupport data transfer or connectionto
a computer.
Don’t connect the USB port of the JCR-295 to other USB charger.It may damage both
units and void the warranty.
E-9
TROUBLE SHOOTING
If you experience difficulties in the use of this music system, please check the following or
call 1-800-777-5331 for Customer Service.
SYMPTOM
No sound
Noise or sound distorted
on FM broadcast
POSSIBLE
SOLUTION
Power adapter connect unstable
Reconnect adapter
Volume set at minimum
Increase Volume level
Wire antenna is not extended
Extend wire antenna
Unit not in RADIO (FM) mode
Press SOURCE Button to
select FM mode.
Retune the station again
Radio no sound
Station unstable
Unit not in Buetooth mode
Bluetooth no operation
Bluetooth connect unstable
Press SOURCE Button to
select Bluetooth mode.
Reconnect again
No music file in mobile
Install music
mobile.
Unit not in AUX mode
Press SOURCE Button to
select AUX mode.
Reconnect again
Aux in no sound
Aux cable connect unstable
USB no changing function USB cable connect unstable
to
your
Reconnect again
TECHNICAL SPECIFICATION
AC Power Requirement
Use AC / DC adapter (included)
Input AC 100~240V ~
Output DC 5V
1200mA
Batteries
2 x AAA ( UM4 ) batteries for backup operation
USB
DC 5V
1000mA for
mobile battery charging only
Audio Section
RMS 1.2 W
FM Radio Section
87.5~108 MHz
For music share with mobile.
Bluetooth version : 2.1
SPECTRA GREEN NOTICE
At Spectra, environmental and social responsibility
is a core value of our business. We are dedicated to
continuous implementation of responsible initiatives
with an aim to conserve and maintain the
environment through responsible recycling.
Please visit us at http://www.spectraintl.com/green.htm for more information on Spectra’s
green initiatives or to find a recycler in your area.
Bluetooth® is a registered trademark of Bluetooth SIG, Inc.
E-10
90 DAY LIMITED WARRANTY AND SERVICE VALID IN THE U.S.A. ONLY
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from
defective materials or factory workmanship for a period of 90 days from the date of
original customer purchase and provided the product is utilized within the U.S.A. This
warranty is not assignable or transferable. Our obligation under this warranty is the
repair or replacement of the defective unit or any part thereof, except batteries, when
it is returned to the SPECTRA Service Department, accompanied by proof of the date of
original consumer purchase, such as a duplicate copy of a sales receipt.
You must pay all shipping charges required to ship the product to SPECTRA for warranty
service. If the product is repaired or replaced under warranty, the return charges will be at
SPECTRA’s expense. There are no other express warranties other than those stated
herein.
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty applies to the SPECTRA product only while:
a. It remains in the possession of the original purchaser and proof of purchase is
demonstrated.
b. It has not been subjected to accident, misuse, abuse, improper service, usage outside
the descriptions and warnings covered within the user manual or non-SPECTRA
approved modifications.
c. Claims are made within the warranty period.
2. This warranty does not cover damage or equipment failure caused by electrical wiring
not in compliance with electrical codes or SPECTRA user manual specifications,
or failure to provide reasonable care and necessary maintenance as outlined in the
user manual.
3. Warranty of all SPECTRA products applies to residential use only and is void when
products are used in nonresidential environment or installed outside the United
States.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state. TO OBTAIN SERVICE please remove all batteries (if any) and
pack the unit carefully and send it freight prepaid to SPECTRA at the address shown below.
IF THE UNIT IS RETURNED WITHIN THE WARRANTY PERIOD shown above, please
include a proof of purchase (dated cash register receipt) so that we may establish your
eligibility for warranty service and repair of the unit without cost. Also include a note with a
description explaining how the unit is defective. A customer service representative may
need to contact you regarding the status of your repair, so please include your name,
address, phone number and email address to expedite the process.
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $20. 00
to cover the cost of repair, handling and return postage. All out of warranty returns must be
sent prepaid.
It is recommended that you contact SPECTRA first at 1-800-777-5331 or by email at
custserv@spectraintl.com for updated information on the unit requiring service. In some
cases the model you have may be discontinued, and SPECTRA reserves the right to offer
alternative options for repair or replacement.
SPECTRA MERCHANDISING INTERNATIONAL, INC.
4230 North Normandy Avenue,
Chicago, IL60634, USA. 1-800-777-5331
To register your product, visit the link on the website below to enter your information.
http://www.spectraintl.com/wform.htm
0314
PRINTED IN CHINA
E-11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising