Quick Guide, NewClassic Balances, MS-S / MS

Quick Guide, NewClassic Balances, MS-S / MS
Easy Weighing Access

Quick Application Access
WEIGHING

Press and hold
F1
Activate weighing
application
Press and hold
• Cancel running
application
0.00 g

F2
0.00 g


NET
Net
0.00 g
PERCENT

Press and hold
SET 100 %
121.01 g
Press briefly

FIX 10 PCS
Tare
#
COUNTING
Execute the assigned
F1 application.
Factory setting:
"Piece Counting"
Press briefly
Execute predefined adjusting
(calibration) procedure
Factory Setting: Internal adjustment
(MSxxxE models: external adjustment)
External Adjustment Procedure
ADJ.EXT
Execute the assigned
F2 application.
Factory setting:
"Percent Weighing"

1000.00 g
Press briefly

Net
F3

Press and hold
CHECK

SET NOM.
22.00 g
Execute the assigned
F3 application.
Factory setting:
"Checkweighing"

0.00 g

Unit 1
------
Recall
ADJ DONE

,
M
* 22.00 g M
Press briefly
,
Application Settings
• if activated
Unit 2
0.78 oz
C
------
Switching Units
,
Direct Adjustment Access

0.00 g
Note:
There is a timeout during the setup. The balance switches back
to the last active application.
• if activated
• if different
from Unit 1
C
Display Panel
Operation Keys
Application Icons
2
Unit Field
1
Status Icons
Weight Value Field
Quick Guide
NewClassic Balances
MS-S / MS-L Models
Status Icons
Weighing-in aid
3
Application Icons
4
C
5
6
9
7
10
8
Key Functions
No.
Key
Press briefly (less than 1.5 s)
Press and hold (longer than 1.5 s)
• To change display resolution (1/10d
function) while application is running
Note: not available with approved models
in selected countries
• Enter or leave menu (Parameter settings)
no function
3
• Execute predefined adjusting (calibration)
procedure
no function
4
•
•
•
•
Printout display value
Printout menu settings
Transmit data
To navigate back (scroll up) within menu
topics or menu selections
• Decrease (numerical) parameters within
menu and in applications
• To navigate forward (scroll down) within
menu topics or menu selections
• Increase (numerical) parameters within
menu and in applications
no function
• With entries: scroll down
• To navigate through menu topics or menu
selections
• To toggle between unit 1, recall value (if
selected), unit 2 (if different from unit 1)
and the application unit (if any)
• To select assigned F2 application and entering the parameter settings of application.
• Default F2 application assignment: Percent
weighing
• To enter or leave menu selection (from / to
menu topic)
• To enter application parameter or switch to
next parameter
• To store parameter
• To select assigned F3 application and entering the parameter settings of application.
• Default F3 application assignment: Checkweighing
• Switch on
• Zero/Tare
• Switch off
1
2
5
6
7
8
9
10
ON/OFF
#
C
• Cancel and to leave menu without saving
(one step back in the menu).
Indicates stored values
(memory)
Menu settings activated
Indicates Net weight values
Application “Weighing”
Adjustments (calibration)
started
Application “Piece counting”
FACT activated
Application “Percent weighing”
Diagnostic mode & Application
“Routine test” activated
Application “Check weighing”
Application “Statistics”
no function
Application
“Formulation / Net-Total”
Application “Totaling”
Application
“Dynamic weighing”
Application
“Multiplication factor”
• To select the weighing application
• Decrease (numerical) parameters quickly
within menu and in applications
• To select assigned F1 application and entering the parameter settings of application.
• Default F1 application assignment: Piece
counting
• Increase (numerical) parameters quickly
within menu and in applications
• no function
Status Icons
Menu locked
Service reminder
Acoustic feedback for pressed
keys activated
Weighing range 1 (Dual Range
models only)
Weighing range 2 (Dual Range
models only)
Charge of battery; full, 2/3, 1/3,
discharged
(Battery operated models only)
Application
“Division factor”
Application “Density”
Weight Value Field
Indicates negative values
Unit Field
Marking of weighing units:
g
gram
kg
kilogram
mg
milligram
ct
carat
lb
pound
oz
ounce
ozt
troy ounce
GN
grain
dwt
pennyweight
mom
momme
msg
mesghal
tlh
Hong Kong taels
tls
Singapore taels
tlt
Taiwan taels
tola
tola
baht
baht
>>
Selection available
Indicates unstable values
Indicates calculated values
Indicates uncertified digits
(approved models only)
Weighing-in aid
Marking of nominal or target
weight
Marking of tolerance limit T+
Marking of tolerance limit T-
Menu Map
Topic
Menu Operation
•Enter menu
•Leave menu
with saving
,
Scroll down
+
BCKLIGHT >> 8

•Enter selection
or menu
•Execute setting
C
•One step back
•Leave menu
without saving
Scroll up
Topic
Selection
B.L. ON
Interface Menu
Selection
RS232 >>

8
PRINTER >> 8

PC-DIR. >>.
B.L. 2 min
8
PRT.STAB
AUTOZERO>> 8
BRIGHTN. >> 8
50 %

CONTRAST>> 8
75 %

PRT.ALL
HOST
>>
8
SEND.OFF
Main
Menu
>> 8 Basic Menu

ON
ADVANCED>> 8 Advanced Menu
ZERO RNG>> 8
21.00 g
LANGUAGE>> 8
ENGLISH
DEUTSCH
INT.FACE >> 8 Interface Menu
SEND.CONT
SEND.AUTO
SEND.ALL
Depending on the language
package installed.
2.DISPLAY ¥
HEADER >>
FRANCAIS
PROTECT >> 8 Protection
8
ESPANOL
Basic Menu
Selection
8
DATE
>>
D/T/BAL
TIME
>> 8

UNIT 1
>> 8
g
12:00
ASSIGN:F1>> 8
KEY BEEP >> 8
STAB.BEEP>> 8
g
¦
FORMULA
NO
TOTALING
>> 8

COM.SET >> 8
HIGH
FACTOR M
OFF
FACTOR D
LOW
DENSITY
ASSIGN:F2>> 8

PERCENT
BAUDRATE >> 8
BIT/PAR. >> 8
7/MARK

7/SPACE
HIGH
STAT
7/ODD
FORMULA
STOPBIT >> 8
TOTALING
Advanced Menu
HD.SHAKE >> 8
ASSIGN:F3>> 8
CHECK
 

FORMULA
200.00 g

>> 8
12:00

OFF

FACTOR D
ON

DENSITY
DD.MM.Y
DIAGNOSE>> 8
Y-MM-DD

>> 8
OFF
QUICK

USB CHAR>> 8
ANSI/WIN

IBM/DOS
INTERVAL>> 8
0
s

PROVIDER

SERV.ICON>> 8
ON

OFF

SRV.D.RST>> 8
FULL
SHUTOFF >> 8
<CR><LF>
<LF>
CAL.HIST
ON
 STARTUP >> 8
USB E.O.L.>> 8
<CR>
BAL.INFO
12.MM

SART

BAL.HIST
24.MM
MT-SICS
MT-PM
CAL.MOT. T 
12:MM
RECALL
USB COM.S.>> 8
KEYPAD T
MMM D Y

SEND.ALL
DISPLAY
D.MMM Y
24:MM
REPEAT.T
SEND.OFF
SEND.AUTO
PERCENT
MM/DD/Y
TIME.FORM>> 8
>> 8
SEND.STB.
COUNTING


SEND.CONT
R.TEST
OFF
DATE.FORM>> 8
USB
FACTOR M

 FACT PRT>> 8
TIME

>> 8
DYNAMIC

FACT
IBM/DOS
ANSI/WIN
TOTALING
ADJ.OFF

<LF>
RS CHAR >> 8

ADJ.EXT >> 8
<CR><LF>
<CR>
STAT
ADJ.INT

OFF
RS E.O.L. >> 8
COUNTING
STABLE
XON/XOFF
RTS/CTS
DENSITY
STANDARD 

1 BIT
2 BITS
DYNAMIC
UNSTABLE


8/NO
7/EVEN
Selection
>> 8
600…38400
7/NO
FACTOR D
CAL
¦
4800
FACTOR M
ENVIRON.>> 8

9600
CHECK
NO?

SART
MED
YES?
Topic
MT-SICS
MT-PM
DYNAMIC

LOW

OFF
STAT
mg
MED
0
ZERO PRT.>> 8
ON
CHECK

LINE.FEED >> 8

PERCENT
OFF
RESET
COUNTING

OFF
ON
BR.PORTUG.

¦
8
MAGYAR
kg
UNIT 2 >> 8
SIGN.L >>
NEDERL.
SET TIME>> 8

NET
G/T/N
CESKY
+1H
8
POLSKI
-1H

SINGLE >>
RUSSIAN
01.01.2008

NO
DAT/TIM
ITALIANO
Topic

SEND.STB
OFF
BASIC

PRT.AUTO
B.L. 5 min


PRT.ALL
B.L. 1 min
DISPLAY >> 8
PRT.STAB
PRT.AUTO
B.L. 30 s
A.OFF10 min 
A.OFF A.OFF 2 min
Selection
OFF

Protection
ON
YES?
Legend
 Factory setting
 Only those weight units allowed by the appropriate
national legislation are selectable.
 Not available with MSxxxE models.
Not available with MSxxxKLIPE models.

A.OFF 5 min
Topic
PROTECT>> 8
NO?


¥
Not available with approved models.
Not available with approved models
(except OIML accuracy class I approved models)
Settings are automatically set for the 2nd display.
www.mt.com/newclassic
For more information
Mettler-Toledo AG
Laboratory & Weighing Technologies
CH-8606 Greifensee, Switzerland
Subject to technical changes
© Mettler-Toledo AG 01/2011 11781215E 7.12
*11781215*
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising