LM-200LED LED Light Meter Product Manual

LM-200LED LED Light Meter Product Manual
LM-200LED
LED Light Meter
Users Manual
• Mode d’emploi
• Bedienungshandbuch
• Manuale d’Uso
• Manual de uso
LED Light Meter
Users Manual
LM-200LED_Rev03
© 2013 Amprobe Test Tools.
All rights reserved.
English
LM-200LED
Limited Warranty and Limitation of Liability
Your Amprobe product will be free from defects in material and workmanship for
1 year from the date of purchase unless local laws require otherwise. This warranty
does not cover fuses, disposable batteries or damage from accident, neglect,
misuse, alteration, contamination, or abnormal conditions of operation or handling.
Resellers are not authorized to extend any other warranty on Amprobe’s behalf.
To obtain service during the warranty period, return the product with proof of
purchase to an authorized Amprobe Test Tools Service Center or to an Amprobe
dealer or distributor. See Repair Section for details. THIS WARRANTY IS YOUR ONLY
REMEDY. ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED OR STAUTORY
- INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR
MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER SHALL NOT BE
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries
do not allow the exclusion or limitation of an implied warranty or of incidental or
consequential damages, this limitation of liability may not apply to you.
Repair
All test tools returned for warranty or non-warranty repair or for calibration should
be accompanied by the following: your name, company’s name, address, telephone
number, and proof of purchase. Additionally, please include a brief description of
the problem or the service requested and include the test leads with the meter. Nonwarranty repair or replacement charges should be remitted in the form of a check, a
money order, credit card with expiration date, or a purchase order made payable to
Amprobe® Test Tools.
In-Warranty Repairs and Replacement – All Countries
Please read the warranty statement and check your battery before requesting
repair. During the warranty period any defective test tool can be returned to your
Amprobe® Test Tools distributor for an exchange for the same or like product.
Please check the “Where to Buy” section on www.amprobe.com for a list of
distributors near you. Additionally, in the United States and Canada In-Warranty
repair and replacement units can also be sent to a Amprobe® Test Tools Service
Center.
Non-Warranty Repairs and Replacement – US and Canada
Non-warranty repairs in the United States and Canada should be sent to a
Amprobe® Test Tools Service Center. Call Amprobe® Test Tools or inquire at your
point of purchase for current repair and replacement rates.
In USA Amprobe Test Tools Everett, WA 98203 Tel: 877-AMPROBE (267-7623) In Canada
Amprobe Test Tools
Mississauga, ON L4Z 1X9
Tel: 905-890-7600
Non-Warranty Repairs and Replacement – Europe
European non-warranty units can be replaced by your Amprobe® Test Tools
distributor for a nominal charge. Please check the “Where to Buy” section on www.
amprobe.com for a list of distributors near you.
European Correspondence Address*
Amprobe® Test Tools Europe
Beha-Amprobe GmbH
In den Engematten 14
79286 Glottertal, Germany
Tel.: +49 (0) 7684 8009 - 0
www.amprobe.eu
*(Correspondence only – no repair or replacement available from this address.
European customers please contact your distributor.)
1
2
3
7
4
6
5
LM-200LED
➊Light Sensor
➋Display(LCD)
➌MAX HOLD
➍Lux / foot candles
➎Power Button: ON/OFF
➏Measurement Range Selection
➐DATA HOLD
➑Light sensor Zero Adjustment
9 Sensor Protective Cap
LM-200LED LED Light Meter
Contents
SYMBOLS............................................................................................................... 1
UNPACKING AND INSPECTION............................................................................. 1
INTRODUCTION..................................................................................................... 1
OPERATION . ......................................................................................................... 1
Lx / fc................................................................................................................. 2
Measurement Range....................................................................................... 2
Maximum Hold................................................................................................ 2
Data Hold ........................................................................................................ 2
Zero Adjustment ............................................................................................. 2
SPECIFICATIONS .................................................................................................... 2
MAINTENANCE AND REPAIR ............................................................................... 3
Battery Replacement ...................................................................................... 4
Symbols
�
Caution! Refer to the
explanation in this
Manual
�
Complies with EU
directives
�
Conforms to relevant
Australian standards.
�
Do not dispose of this
product as unsorted
municipal waste.
� Warning and Precautions
• Do not operate the meter in explosive gas (material), combustible gas
(material) steam or filled with dust.
• The light sensor is calibrated to CIE standard incandescent lamp at 2856 °K
and may give different readings for spectrums from other lamp types.
Unpacking and Inspection
Your shipping carton should include:
1
LM-200LED LED light meter
1
9 volt battery
1
Users Manual
1
Carrying case
If any of the items are damaged or missing, return the complete package to
the place of purchase for an exchange.
Introduction
The instrument measures light output of LED sources for all visible light
ranges.
The lumen is a measure of total amount of visible lights emitted by a source.
The lumen is defined as in relation to the candela as 1 lm = 1 cd.sr.
A foot-candle is the luminance cast on a surface by a one-candela source
one foot away. One foot-candela is equal to one lumen per square foot or
approximately 10.764 lux.
Operation
1. Press the � button to turn power on or off
2. Remove sensor protective cap and place the sensor perpendicular to the
light.
3. Select the measurement unit (LUX or FC) by using
4. Set the measurement range by using
1
button.
button.
5. Press
button to obtain the maximum reading during measurement.
6. Press
button to freeze the present reading on the display.
�
Always put the sensor protective cap back when the instrument is not
in use.
Lx / fc
button to select the measurement unit.
Press
1 foot-candle = 10.764 Lux and 1 Lux = 0.09290 foot-candle
Measurement Range
button to select the measurement range. An “OL.” Symbol on
Press
display indicates over-range, select a higher range for measurement.
Maximum Hold
button to obtain the maximum reading during measurement
Press
(MAX symbol shows on display).
button again to exit maximum hold mode (MAX symbol
Press
disappears on display).
Data Hold
button to freeze present reading on display (D-H symbol shows
Press
on display).
button again to resume measurement (D-H symbol disappears
Press
on display).
Zero Adjustment
The instrument zero may change over time. To reset to zero follow the
instructions:
1. Make sure the sensor protective cap is fully covered on the sensor.
2. Set the range at the lowest LUX or FC range
3. Using a small flat screwdriver to adjust zero control (0 ADJ) until display
shows ”0.00”.
Specifications
General
Display: 2000 count LCD
Sensor: Silicon photodiode and filter.
Environment: Indoor operation
Altitude: Up to 2000m.
2
Temperature / Humidity
Operating: -10 °C to 40 °C (14˚F to 104˚F), 0 to 80 %RH.
Storage: -10 °C to 50 °C (14˚F to 122˚F), 0 to 70 %RH.
Power Supply: 9V NEDA 1604, IEC 6F22, JIS 006P battery Battery life: typical 200 hours (Alkaline)
Auto Power Off: approx 6 min
Dimension (Base): 130 x 63 x 38 mm (5.1 x 2.5 x 1.5”)
Dimension (Sensor): 80 x 55 x 29 mm (3.2 x 2.2 x 1.1”)
Weight: 220 g (.48 lb.) include battery
�
-EMC: EN61326-1 This product complies with requirements of the
following European Community Directives: 89/336/EEC (Electromagnetic
Compatibility) and 73/23/EEC (Low Voltage) as amended by 93/68/EEC (CE
Marking). However, electrical noise or intense electromagnetic fields in the
vicinity of the equipment may disturb the measurement circuit. Measuring
instruments will also respond to unwanted signals that may be present within
the measurement circuit. Users should exercise care and take appropriate
precautions to avoid misleading results when making measurements in the
presence of electronic interference.
Illumination:
Measuring Range: 200, 2000, 20000, 200000 Lux
20, 200, 2000, 20000 Foot candles
Accuracy: ±3% for white LED light (Calibrated to standard incandescent lamp 2856º K and corrected LED day white-light spectrum).
± 8% for other visible light sources
Angle deviation from cosine Characteristics
30 ° ± 2 %
60 ° ± 6 %
80 ° ± 25 %
Cosine Angular corrected per JIS C 1609:1993 and CNS 5119 general A class
specifications.
Maintenance and Repair
If there appears to be a malfunction during the operation of the meter, the
following steps should be performed in order to isolate the cause of the
problem.
1. Check the battery. Replace the battery immediately when the symbol
“�” appears on the LCD.
2. Review the operating instructions for possible mistakes in operating
procedure.
3
Except for the replacement of the battery, repair of the meter should be
performed only by a Factory Authorized Service Center or by other qualified
instrument service personnel. The front panel and case can be cleaned with
a mild solution of detergent and water. Apply sparingly with a soft cloth and
allow to dry completely before using. Do not use aromatic hydrocarbons or
chlorinated solvents for cleaning.
Battery Replacement
1. Turn off the meter and slide out the battery cover. Replace the battery
with a NEDA type 1604 or equivalent 9V alkaline battery. Replace the
cover.
2. Remove battery when the instrument is not used for extended period.
OPEN
Battery Replacement
4
Visit www.Amprobe.com for
•Catalog
•Application notes
•Product specifications
•User manuals
Please Recycle
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising