Indoor Siren SE 200/601/701
Indoor Siren SE 200/601/701
p r o d u c t
s p e c i f i c a t i o n
s h e e t
Doc. - Ref. 225
Version : June 2013
> Wireless technology provides optimum signal
integrity and security
> Speaker providing output of 110dB at 1 meter
up to three minutes, in alarm.
> Dual tamper
The Indoor Siren Model SE is a battery operated, wireless
siren designed for use in Videofied security systems.
The siren consists of a sounder and S2View® Spread
Spectrum, Videofied, interactive, encrypted wireless circuitry
for secure two-way communication with the control panel.
The siren produces an output level of 110 dB at 1 meter during 1,5
to 3 minutes, in alarm.
The siren is typically installed in hallways, foyers,
or other similar areas where sound can resonate so
occupants can hear alarms. A dual tamper function
provides detection for both wall and cover tamper.
The siren is powered by four alkaline batteries that
can last four years, depending on the amount of siren
activity. The siren transmits a check-in signal every eight
minutes that includes its unique identification code,
along with the tamper condition and battery status.
> S2View® - Spread Spectrum, Videofied, Interactive AES
Encrypted Wireless technology provides optimum signal
integrity and security.
> Speaker - provides output of 110dB at 1 meter for up to three
minutes, in alarm.
> Supervised - transmits a check-in/status signal every 8 minutes
indicating tamper state and battery status.
> Dual tamper - provides detection for wall and cover tamper.
> Four D cell 1.5v Alkaline batteries - four years.
> Annunciation of alarm sounds in Videofied security systems.
T e c h n i c a l
s p e c i f i c a t i o n s
Indoor Siren SE 200/601/701
FCC Regulatory Information for USA and CANADA
FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI VideoTechnologies may void the FCC
authorization to operate this equipment.
FCC Part 15.105 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver.
> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
> Consult the dealer or an experienced radio/TV technician for help.
Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la Partie 15 des règlementations de la FCC et avec la norme RSS-210 de l’Industrie Canadienne.
Son fonctionnement est soumis aux deux conditions suivantes :
1 Cet appareil ne doit pas causer d’interférences nuisibles et
2 Cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant entraîner un fonctionnement indésirable.
© 2013 RSI Video Technologies Videofied® and MotionViewer® are Registered Trademark of RSI Video Technologies.
Specifications subject to change without notice.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
T e c h n i c a l
s p e c i f i c a t i o n s
Indoor Siren SE 200/601/701
Electrical Data
Panel Compatibility
XL, XLL, Visio, XT, XT-iP, XV, XV-iP
Four 1.5 V Alkaline Batteries
Power requirements
Nominal Voltage
Low Battery Limit
Battery type
Energizer Alkaline LR20, D size
Battery life
Physical Data
(LxWxD) 280 mm x 158 mm x 57 mm
11 in.x 6-1/4 in. x 2-1/4 in.
740 g/26 oz.(without batteries)
Up to 4 years
RF technology
Radio type
Spread Spectrum Bidirectional
Operating frequency
868 MHz
915 MHz
920 MHz
Transmission security
AES encryption algorithm
Supervision Polled signal every
8 minutes
Installation / Mounting
Two screws secure siren to base; three screws
secure siren base to mounting surface.
Tamper detection
Wall and cover tampered
Speaker impedance
4 ohms
Output level
110 dB at 1 meter
Output duration
Configured in Control Panel
Built-in sounder
Emits entry/exit delay beeps, alarms
Operating temperature
Maximum relative humidity
-10°/+40°C (14°/104°F)
70%, non-condensing
Certification & Approvals
FCC Part 15C
North American Headquarters
23, avenue du Général Leclerc
E-Mail :
1375 Willow Lake Blvd, Suite 103
Vadnais Heights, MN 55110
E-Mail :
© 2013 RSI Video Technologies Videofied® and MotionViewer® are Registered Trademark of RSI Video Technologies.
Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF