NEC V651 Datasheet

Add to My manuals
44 Pages

advertisement

NEC V651 Datasheet | Manualzz

User’s Manual

MultiSync V422

MultiSync V462

MultiSync V651

(For use in landscape position only)

Index

DECLARATION OF CONFORMITY ............................................................................................................. English-1

Important Information ................................................................................................................................... English-2

WARNING ....................................................................................................................................... English-2

CAUTION ........................................................................................................................................ English-2

Declaration ................................................................................................................................................... English-2

Safety Precautions, Maintenance & Recommended Use............................................................................. English-3

Contents ....................................................................................................................................................... English-4

Installation .................................................................................................................................................... English-5

Attaching Mounting Accessories ..................................................................................................... English-6

Parts Name and Functions ........................................................................................................................... English-8

Control Panel .................................................................................................................................. English-8

Terminal Panel ................................................................................................................................ English-9

Wireless Remote Control ................................................................................................................ English-11

Operating Range for the Remote Control ....................................................................................... English-12

Setup ............................................................................................................................................................ English-13

Connections ................................................................................................................................................. English-15

Wiring Diagram ............................................................................................................................... English-15

Connecting a Personal Computer ................................................................................................... English-16

Connecting a DVD Player or Computer with HDMI out .................................................................. English-16

Connecting a Computer with DisplayPort ....................................................................................... English-16

Basic Operation ............................................................................................................................................ English-17

Power ON and OFF Modes ............................................................................................................ English-17

Power Indicator ............................................................................................................................... English-18

Using Power Management ............................................................................................................. English-18

Selecting a video source ................................................................................................................. English-18

Picture Aspect ................................................................................................................................. English-18

Information OSD ............................................................................................................................. English-19

Picture Mode ................................................................................................................................... English-19

OSD (On-Screen-Display) Controls.............................................................................................................. English-20

PICTURE ........................................................................................................................................ English-21

ADJUST .......................................................................................................................................... English-21

AUDIO ............................................................................................................................................ English-22

SCHEDULE .................................................................................................................................... English-22

PIP .................................................................................................................................................. English-23

OSD ................................................................................................................................................ English-23

MULTI DISPLAY ............................................................................................................................. English-24

DISPLAY PROTECTION ................................................................................................................ English-25

ADVANCED OPTION ..................................................................................................................... English-26

Remote Control Function .............................................................................................................................. English-29

Controlling the LCD monitor via RS-232C Remote Control.......................................................................... English-31

Controlling the LCD monitor via LAN Control ................................................................................................ English-32

Connecting to a Network ................................................................................................................ English-32

Network Setting by Using an HTTP Browser .................................................................................. English-32

Features ....................................................................................................................................................... English-36

Troubleshooting ............................................................................................................................................ English-37

Specifi cations - V422 .................................................................................................................................... English-38

Specifi cations - V462 .................................................................................................................................... English-39

Specifi cations - V651 .................................................................................................................................... English-40

Pin Assignment ............................................................................................................................................. English-41

Manufacturer’s Recycling and Energy Information ....................................................................................... English-42

www.necdisplaysolutions.com

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U.S. Responsible Party: NEC Display Solutions of America, Inc.

Address: 500 Park Boulevard, Suite 1100

Illinois

Type of Product: Display Monitor

Equipment Classifi cation: Class B Peripheral

Model: MultiSync V422 (L420UA)

MultiSync V462 (L460UB)

MultiSync V651 (L650U9)

We hereby declare that the equipment speciÞ ed above conforms to the technical standards as speciÞ ed in the FCC Rules.

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.

FCC Information

1. Use the attached specifi ed cables with the MultiSync V422 (L420UA)/MultiSync V462 (L460UB)/MultiSync V651 (L650U9) colour monitor so as not to interfere with radio and television reception.

(1) Please use the supplied power cord or equivalent to ensure FCC compliance.

(2) Please use the supplied shielded video signal cable, Mini D-SUB 15 pin to Mini D-SUB 15 pin.

2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.

The user may fi nd the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Offi ce, Washington,

D.C., 20402, Stock No. 004-000-00345-4.

Windows is a registered trademark of Microsoft Corporation.

NEC is a registered trademark of NEC Corporation.

OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and

Switzerland.

DisplayPort is trademarks of Video Electronics Standards Association.

All other brands and product names are trademarks or registered trademarks of their respective owners.

HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

English-1

Important Information

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT

USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE

PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM

WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER

CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have suffi cient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION: Please use the power cord provided with this monitor in accordance with the table below. If a power cord is not supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the

AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.

Plug Type North America

European

Continental

U.K.

Chinese Japanese

Plug Shape

Region

Voltage

U.S.A./Canada

120*

EU (except U.K.)

230

U.K.

230

China

220

Japan

100

* When operating the monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used.

NOTE: This product can only be serviced in the country where it was purchased.

Declaration

We hereby certify that the color monitor MultiSync V422

(L420UA)/MultiSync V462 (L460UB)/MultiSync V651

(L650U9) are in compliance with

Council Directive 2006/95/EC:

– EN 60950-1

Council Directive 2004/108/EC:

– EN 55022

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

Council Directive 2009/125/EC:

EC No. 642/2009

– EN 62301:2005 and marked with

NEC Display Solutions, Ltd.

4-13-23, Shibaura,

Minato-Ku

Tokyo 108-0023, Japan

English-2

Safety Precautions, Maintenance & Recommended Use

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING

THE MULTI-FUNCTION MONITOR:

DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualifi ed service personnel.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful or fatal or may cause electric shock, fi re or equipment failure.

• Do not place any heavy objects on the power cord.

Damage to the cord may cause shock or fi re.

• Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to the monitor.

• Do not mount this product face up, face down or upside down for an extended period of time as it may cause permanent damage to the screen.

• The power supply cord you use must have been approved by and comply with the safety standards of your country. (Type

H05VV-F 3G 1mm 2 should be used in Europe)

• In UK, use a BS-approved power cord with molded plug having a black (13A) fuse installed for use with this monitor.

• Do not place any objects onto the monitor and do not use the monitor outdoors.

Immediately unplug your monitor from the wall outlet and refer servicing to qualifi ed service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If you notice any structural damage such as cracks or unnatural wobbling.

• If the monitor does not operate normally by following operating instructions.

Recommended Use

• For optimum performance, allow 20 minutes for warm-up.

• Rest your eyes periodically by focusing on an object at least

5 feet away. Blink often.

• Position the monitor at a 90° angle to windows and other light sources to minimize glare and refl ections.

• Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any cleaning solution or glass cleaner!

• Adjust the monitor’s brightness, contrast and sharpness controls to enhance readability.

• Avoid displaying fi xed patterns on the monitor for long periods of time to avoid image persistence (after image effects).

• Get regular eye checkups.

Ergonomics

The lamps in this product contain mercury. Please dispose according to state, local or federal law.

• Do not bend, crimp or otherwise damage the power cord.

• If glass is broken, handle with care.

• Do not cover vent on monitor.

• Do not use monitor in high temperature, humid, dusty, or oily areas.

• If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.

• Allow adequate ventilation around the monitor, so that heat can properly dissipate. Do not block ventilated openings or place the monitor near a radiator or other heat sources.

Do not put anything on top of the monitor.

• The power cable connector is the primary means of detaching the system from the power supply. The monitor should be installed close to a power outlet, which is easily accessible.

• Do not move or mount this product by hanging a rope or wire to the backside handle.

Do not mount or secure this product by using the backside handle. It may fall and cause personal injury.

• Handle with care when transporting. Save packaging for transporting.

• If using the cooling fan continuously, it is recommended to wipe holes clean a minimum of once a month.

• Please clean the holes of back cabinet to reject dirt and dust at least once a year because of set reliability.

• When using a LAN cable, do not connect to a peripheral device with wiring that might have excessive voltage.

Connecting to a TV*

• Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code

(NEC), in particular Section 820.93, Grounding of Outer

Conductive Shield of a Coaxial Cable.

• The screen of the coaxial cable is intended to be connected to earth in the building installation.

To realize the maximum ergonomic benefi ts, we recommend the following:

• Use the preset Size and Position controls with standard signals.

• Use the preset Color Setting.

• Use non-interlaced signals.

• Do not use primary color blue on a dark background, as it is diffi cult to see and may produce eye fatigue due to insuffi cient contrast.

Cleaning the LCD Panel

• When the liquid crystal panel is dusty, please gently wipe with a soft cloth.

• Please do not rub the LCD panel with hard material.

• Please do not apply pressure to the LCD surface.

• Please do not use OA cleaner as it will cause deterioration or discolor on the LCD surface.

Cleaning the Cabinet

• Unplug the power supply

• Gently wipe the cabinet with a soft cloth

• To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and follow with a dry cloth.

NOTE: DO NOT clean with benzene thinner, alkaline detergent, alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Rubber or vinyl should not be in contact with the cabinet for an extended period of time. These types of fl uids and materials can cause the paint to deteriorate, crack or peel.

* The product you purchased may not have this feature.

English-3

Contents

Your new MultiSync monitor box* should contain the following:

• Power 1

• Video Signal Cable

• Wireless Remote Control and AA Batteries

• Clamp x 2* 2

• Screw (M4 x 10) x 2* 2

• CD-ROM

• Thumbscrew for optional stand x 2* 2

• Eyebolt x 2* 3

Video Signal Cable

(Mini D-SUB 15 pin to

Mini D-SUB 15 pin)

Power Cord* 1

Screw (M4 x 10) x 2* 2 Thumbscrew for optional stand x 2* 2

Clamp x 2* 2

Setup Manual

Complete

User's Manual

Information Files for

Windows Eyebolt x 2* 3

Setup Manual Wireless Remote Control and AA Batteries

* Remember to save your original box and packing material to transport or ship the monitor.

* 1 Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.

* 2 Except for V651.

* 3 V651

English-4

Installation

This device cannot be used or installed without the Tabletop

Stand or other mounting accessory for support. For proper installation it is strongly recommended to use a trained,

NEC authorized service person. Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation.

Failure to follow these recommendations could result in voiding the warranty.

Mounting

DO NOT mount the monitor yourself. Please ask dealer.

For proper installation it is strongly recommended to use a trained, qualifi ed technician. Please inspect the location where the unit is to be mounted. Mounting on wall or ceiling is the customer’s responsibility. Not all walls or ceilings are capable of supporting the weight of the unit. Product warranty does not cover damage caused by improper installation, remodelling, or natural disasters. Failure to comply with these recommendations could result in voiding the warranty.

DO NOT block ventilated openings with mounting accessories or other accessories.

For NEC Qualifi ed Personnel:

To ensure safe installation, use two or more brackets to mount the unit. Mount the unit to at least two points on the installation location.

Please note the following when mounting on wall or ceiling

• When using mounting accessories other than those that are NEC approved, they must comply with the VESAcompatible (FDMlv1) mounting method.

V422/V462: NEC strongly recommends using size

Unit No gap Mounting

Bracket

M6 screws (15-16 mm +

Washer thickness of bracket and washer in φ 8.5 mm (V422/V462)

φ 10.0 mm (V651)

Screw length). If using screws longer than 15-16 mm, check the depth of the

15-16 mm

Thickness hole. (Recommended Fasten

Screw length should equal

Force: 470 - 635N•cm)

NEC recommends mounting of bracket and washer depth of hole (15-16 mm) + the thickness of mounting bracket interfaces that comply with and washer. Bracket hole should

UL1678 standard in North be under φ 8.5 mm (V422/

America.

V462), φ 10.0 mm (V651).

V651 only: NEC strongly recommends using size M8 screws (15-16 mm + thickness of bracket in length). If using screws longer than 15-16 mm, check the depth of the hole. (Recommended Fasten Force: 1125 -

1375N•cm) NEC recommends mounting interfaces that comply with UL1678 standard in North America.

• Prior to mounting, inspect the installation location to insure that it is strong enough to support the weight of the unit so that the unit will be safe from harm.

• Refer to the instructions included with the mounting equipment for detailed information.

• Make sure there is no gap between the monitor and the bracket.

Orientation (V422/V462)

• When using the monitor in the portrait position, the monitor should be rotated clockwise so that the left side is moved to the top and the LED indicator light is on the bottom. This will allow for proper ventilation and will extend the lifetime of the monitor. Improper ventilation may shorten the lifetime of the monitor.

Orientation (V651 only)

• DO NOT use this monitor in the portrait position.

Doing so may cause failure and void the warranty.

Mounting location

• The ceiling and wall must be strong enough to support the monitor and mounting accessories.

• DO NOT install in locations where a door or gate can hit the unit.

• DO NOT install in areas where the unit will be subjected to strong vibrations and dust.

• DO NOT install near where the main power supply enters the building.

• Do not install in where people can easily grab and hang onto the unit or the mounting apparatus.

• When mounting in a recessed area, as in a wall, leave at least 4 inches (100 mm) of space between the monitor and the wall for proper ventilation.

• Allow adequate ventilation or provide air conditioning around the monitor, so that heat can properly dissipate away from the unit and mounting apparatus.

English-5

Mounting on ceiling

• Ensure that the ceiling is sturdy enough to support the weight of the unit and the mounting apparatus over time, against earthquakes, unexpected vibrations, and other external forces.

• Be sure the unit is mounted to a solid structure within the ceiling, such as a support beam. Secure the monitor using bolts, spring lock washers, washer and nut.

• DO NOT mount to areas that have no supporting internal structure. DO NOT use wood screws or anchor screws for mounting. DO NOT mount the unit to trim or to hanging fi xtures.

Maintenance

• Periodically check for loose screws, gaps, distortions, or other problems that may occur with the mounting apparatus. If a problem is detected, please refer to qualifi ed personnel for service.

• Regularly check the mounting location for signs of damage or weakness that may occur over time.

Attaching Mounting Accessories

The monitor is designed for use with the VESA mounting system.

1. Attach eyebolts for mounting (V651 only)

This model is equipped with attachable eyebolts to aid in mounting.

• Screw the eyebolts into eyebolt holes as shown in the picture.

• Be sure eyebolts are secure.

• In order to move the monitor into position, use a lifting device attached to the eyebolts.

DO NOT mount the monitor using only the eyebolts.

Use an approved mounting accessory.

Eyebolt

Eyebolt

Hole

2. Attach Mounting Accessories

Be careful to avoid tipping monitor when attaching accessories.

VESA Mounting Interface

300 mm (V422/V462)

400 mm (V651)

Mounting accessories can be attached with the monitor in the face down position. To avoid damaging the screen face, place the protective sheet on the table underneath the LCD.

The protective sheet was wrapped around the LCD in the original packaging. Make sure there is nothing on the table that can damage the monitor.

When using mounting accessories other than NEC compliant and approved, they must comply with the VESA-compatible mounting method.

NOTE (for V651):

• Do not leave the monitor in the face-up or face-down position for more than one hour as this may result in a negative effect on the screen's performance.

• Prior to installation, be sure to place the monitor on a fl at area with adequate space.

English-6

3. Installing and removing optional table top stand

CAUTION: Installing and removing the stand must be done by two or more people for V422/V462, by four or more people for V651.

To install, follow those instructions included with the stand or mounting apparatus. Use only those devices recommended by the manufacturer.

NOTE: Use ONLY thumbscrews which are included in the monitor. For V651, use ONLY the thumbscrews which are included with the optional table top stand.

When installing the stand, handle the unit with care to avoid pinching your fi ngers.

Optional table top stand

5. Prevent Tipping

When using the monitor with the optional table top stand fasten the LCD to a wall using a cord or chain that can support the weight of the monitor in order to prevent the monitor from falling. Fasten the cord or chain to the monitor using the provided clamps and screws. For the V651, the clamps and screws are included with the optional table top stand.

204 mm (V422/V462)

400 mm (V651)

Screw Holes

Clamp

Cord or chain

Screw

Before attaching the LCD monitor to the wall, make sure that the wall can support the weight of the monitor.

Be sure to remove the cord or chain from the wall before moving the LCD.

Table

Protective Sheet

NOTE: For V422/V462, install the stand so the long end of the feet face forward.

For V651, install the stand in the direction of the arrow which is imprinted on the surface of the stand.

Use the ST-4020 for the V422, the ST-4620 for the

V462 and the ST-651 for the V651.

4. Ventilation Requirements

When mounting in an enclosed space or recessed area, leave adequate room between the monitor and the enclosure to allow heat to disperse, as shown below.

Allow adequate ventilation or provide air conditioning around the monitor, so that heat can properly dissipate away from the unit and mounting apparatus; especially when you use monitors in multiple screen.

NOTE: The sound quality of the internal speakers will differ according to the acoustics of the room.

English-7

Parts Name and Functions

Control Panel

POWER button

Switches the power on/off. See also page 17.

MUTE button

Switches the audio mute ON/OFF.

INPUT button

Acts as SET button within OSD menu. (Toggle switches between [DVI], [DPORT], [VGA], [RGB/HV], [HDMI],

[DVD/HD], [SCART], [VIDEO1], [VIDEO2] or [S-VIDEO]).

These are available input only, shown as their factory preset name.

PLUS button

Acts as (+) button to increase the adjustment with OSD menu.

Increases the audio output level when the OSD menu is turned off.

MINUS button

Acts as (-) button to decrease the adjustment with OSD menu.

Decreases the audio output level when the OSD menu is turned off.

UP button

Activates the OSD menu when the OSD menu is turned-off.

Acts as button to move the highlighted area up to select adjustment items within OSD menu.

DOWN button

Activates the OSD menu when the OSD menu is turned-off.

Acts as button to move the highlighted area down to select adjustment items within OSD menu.

EXIT button

Activates the OSD menu when the OSD menu is turned-off.

Acts as EXIT button within the OSD to move to previous menu.

Remote control sensor and Power Indicator

Receives the signal from the remote control (when using the wireless remote control). See also page 11.

Glows green when the LCD monitor is in active mode*.

Glows red when the LCD is in POWER OFF mode.

Glows both green and red when the monitor is in Power Save

Mode. Glows red and blinks green while in Power Standby mode with the “SCHEDULE SETTINGS” function enabled.

When a component failure is detected within the monitor, the indicator will blink red.

* If “OFF” is selected in “POWER INDICATOR” (see page 24),

LED will not light when the LCD monitor is in active mode.

Control Key Lock Mode

This control completely locks out access to all Control Key functions. To activate the control key lock function, press both and and hold down simultaneously for more than

3 seconds. To resume user mode, press both and and hold simultaneously for more than 3 seconds.

*: The product you purchased may not have this feature.

English-8

Terminal Panel

H

(IN)

V

(IN)

B, Cb/Pb

(IN)

L/R

(IN2)

L

(IN3) R L

AC IN

MAIN POWER

LAN

REMOTE

OUT

RS-232C

OUT

REMOTE

IN

RS-232C

IN

DISPLAYPORT

IN

DVI-D

OUT

HDMI

DVI-D

IN

AC IN connector

Connects with the supplied power cord.

Main Power Switch

On/Off switch to turn main power ON/OFF.

LAN port (RJ-45)

LAN connection. See page 32.

REMOTE IN/OUT

Use the optional wired remote control by connecting it to your monitor.

NOTE: When you use Remote IN/OUT, IR CONTROL in OSD menu should be NORMAL.

NOTE: Do not use this connector unless specifi ed.

RS-232C (D-Sub 9 pin)

IN connector: Connect RS-232C input from external equipment such as a PC in order to control RS-232C functions.

OUT connector: Connect RS-232C output. To connect multiple MultiSync monitors via RS-232C daisy Chain.

DISPLAYPORT connector

IN connector: To input DisplayPort signals.

DVI IN (DVI-D)

To input digital RGB signals from a computer or HDTV device having a digital RGB output.

* This connector does not support analog input.

DVI OUT (DVI-D)

To output the DVI signal from either DVI IN or HDMI connection. To output the DVI signal from the HDMI connection, the HDMI input must be selected.

HDMI connector

To input digital HDMI signals.

R, Cr/Pr

(IN)

G, Y, VIDEO

(IN)

L/R

(IN1)

R

(IN3)

VGA IN (mini D-Sub 15 pin)

To input analog RGB signals from a personal computer or from other RGB equipment.

RGB/HV IN [R, G, B, H, V] (BNC)*

To input analog RGB signals or signals from other RGB equipment.

This is also to connect equipment such as a DVD player,

HDTV device and Set-Top-Box. Sync-on-Green signal can be connected to the G connector.

This input can be used with an RGB, DVD/HD or Video source. Please select signal type in TERMINAL SETTING.

VIDEO 1 IN connector (BNC)*

To input a composite video signal.

VIDEO OUT connector (BNC)

To output the composite video signal from the VIDEO IN connector.

AUDIO OUT

To output the audio signal from the AUDIO IN 1, 2, 3, DPORT and HDMI to an external device (stereo receiver, amplifi er, etc.).

S-VIDEO IN connector (Mini DIN 4 pin)

To input the S-video (Y/C separate signal).

AUDIO IN 1, 2, 3

To input audio signal from external equipment such as a computer, VCR or DVD player.

EXTERNAL SPEAKER TERMINAL

To output the audio signal from AUDIO 1, 2, 3, DPORT and

HDMI.

Red terminal is plus (+).

Black terminal is minus (-).

Note: This speaker terminal is for 15W + 15W (8 ohm) speaker.

English-9

Internal/External Switch speaker

Switch to turn internal speaker/external speaker.

: Internal speaker : External speaker.

NOTE: Please power off the monitor when you use Internal/

External speaker switch.

Kensington Lock

For security and theft prevention.

Option board slot

Slot for board accessories. Please contact your supplier for detailed information.

NOTE: Please contact your supplier for available option board.

NOTE: When you use an option board, which is compliant with Intel’s OPS standard, you need to install it with the optional “SB-02AM” adapter.

Internal speaker

Cable holder

* BNC input signal

English-10

Wireless Remote Control

POWER button

Switches the power on/standby.

INPUT button

Selects input signal.

DVD/HD: DVD/HD, SCART

VIDEO: VIDEO1, VIDEO2

OPTION: Depends on your connection

PICTURE MODE button

Selects picture mode, [HIGHBRIGHT], [STANDARD],

[sRGB], [CINEMA]. See page 19.

HIGHBRIGHT: for moving images such as DVD.

STANDARD: for images.

sRGB: for text based images.

CINEMA: for movies.

ASPECT button

Selects picture aspect, [FULL], [WIDE], [DYNAMIC], [1:1],

[ZOOM] and [NORMAL]. See page 18.

Note: HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only.

SOUND button

Artifi cial surround sound for internal/external speakers.

Audio out is disabled when surround is set to ON.

English-11

KEYPAD

Press buttons to set and change passwords, change channel and set REMOTE ID.

ENT button* 2

DISPLAY button

Turns on/off the information OSD. See page 19.

MENU button

Turns on/off the menu mode.

AUTO SETUP button

Enters auto setup menu. See page 21.

EXIT button

Returns to previous menu within OSD menu.

UP/DOWN button

Acts as button to move the highlighted area up or down to select adjustment items within OSD menu.

Small screen which adjusted “PIP” mode moves up or down.

MINUS/PLUS (-/+) button

Increases or decreases the adjustment level within OSD menu settings.

Small screen which adjusted “PIP” mode moves left or right.

SET button

Makes selection.

VOLUME UP/DOWN button

Increases or decreases audio output level.

CH UP/DOWN button* 2

GUIDE button* 2

MUTE button

Turns on/off mute function.

STILL button

ON/OFF button: Activates/deactivates still picture mode.

STILL CAPTURE button: Captures still picture.

PIP (Picture In Picture) button

ON/OFF button: Toggle switches between PIP, POP,

PICTURE BY PICTURE-ASPECT and PICTURE BY

PICTURE-FULL. See page 23.

INPUT button: Selects the “picture in picture” input signal.

CHANGE button: Replaces to the main picture and sub picture.

Sub picture

DVI DPORT VGA RGB/HV HDMI DVD/HD

DPORT Yes

RGB/HV Yes

DVD/HD Yes

VIDEO1 Yes

VIDEO2 Yes

S-VIDEO Yes

REMOTE ID button

Activates REMOTE ID function.

MTS button* 2

AUDIO INPUT button

Selects audio input source [IN1], [IN2], [IN3], [HDMI],

[DPORT], [OPTION]* 1 .

button

Activates closed captioning.

Note: VIDEO1, VIDEO2, S-VIDEO inputs only.

*1: The product you purchased may not have this feature.

*2: This button’s action depends on which option board you use.

Refer to the option board’s manual for further information.

Operating Range for the Remote

Control

Point the top of the remote control toward the LCD monitor’s remote sensor during button operation.

Use the remote control within a distance of about 7 m (23 ft.) from remote control sensor or at a horizontal and vertical angle of within 30° within a distance of about 3.5 m (10 ft.).

Caution: Important, the remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor or when there is an object in the path.

Handling the remote control

• Do not subject to strong shock.

• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.

• Avoid exposure to heat and steam.

• Other than to install the batteries, do not open the remote control.

English-12

Setup

1. Determine the installation location

CAUTION: Installing your LCD monitor must be done by a qualifi ed technician. Contact your dealer for more information.

CAUTION: MOVING OR INSTALLING THE LCD MONITOR

MUST BE DONE BY TWO OR MORE PEOPLE

FOR V422/V462, BY FOUR OR MORE PEOPLE

FOR V651. Failure to follow this caution may result in injury if the LCD monitor falls.

CAUTION: Do not mount or operate the monitor upside down, face up, or face down.

CAUTION: This LCD has a temperature sensor and cooling fan. If the LCD becomes too hot, the cooling fan will turn on automatically. If the LCD becomes overheated while the cooling fan is running, a

“Caution” warning will appear. If the “Caution” warning appears, discontinue use and allow the unit to cool. Using the cooling fan will reduce the likelihood of early circuit failure and may help reduce image degradation and “Image

Persistance”.

If the LCD is used in an enclosed area or if the

LCD panel is covered with a protective screen, please check the inside temperature of the monitor by using the “HEAT STATUS” control in the OSD (see page 25). If the temperature is higher than the normal operating temperature, please turn the cooling fan to ON within the FAN

CONTROL menu within the OSD (see page 25).

IMPORTANT: Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel.

2. Install the remote control batteries

The remote control is powered by two 1.5V AA batteries.

To install or replace batteries:

NEC recommends the following battery use:

• Place “AA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment.

• Do not mix battery brands.

• Do not combine new and old batteries. This can shorten battery life or cause liquid leakage of batteries.

• Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment.

• Do not touch exposed battery acid, it may injure skin.

NOTE: If you do not intend to use the Remote Control for a long period of time, remove the batteries.

3. Connect external equipment

(See pages 15 and 16)

• To protect the external equipment; turn off the main power before making connections.

• Refer to your equipment user manual for further information.

NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image.

4. Connect the supplied power cord

• The equipment should be installed close to an easily accessible power outlet.

• Fully insert the prongs into the power outlet socket.

A loose connection may cause image degradation.

• Place the power cord within the cable holder.

NOTE: Please refer to the “Safety Precautions and

Maintenance” section of this manual for proper selection of AC power cord.

A. Press and slide to open the cover.

B. Align the batteries according to the (+) and (–) indications inside the case.

C. Replace the cover.

CAUTION: Incorrect usage of batteries can result in leaks or bursting.

English-13

5. Switch on the power of all the attached external equipment

When connected with a computer, switch on the power of the computer fi rst.

6. Operate the attached external equipment

Display the signal from the desired input source.

7. Adjust the sound

Make volume adjustments when required.

8. Adjust the screen (See pages 21 and 22)

Make adjustments of the screen display position when necessary.

9. Adjust the image (See page 21)

Make adjustments such as backlight or contrast when required.

10. Recommended Adjustments

To reduce the risk of the “Image Persistence”, please adjust the following items based on the application being used:

“SCREEN SAVER”, “SIDE BORDER COLOR” (See page 25)

“DATE & TIME”, “SCHEDULE SETTINGS” (See page 22).

It is recommended that the “FAN CONTROL” setting

(See page 25) be turned to ON also.

English-14

Connections

NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image.

NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.

Before making connections:

* First turn off the power of all the attached equipment and make connections.

* Refer to the user manual included with each separate piece of equipment.

Wiring Diagram

Second monitor*

Computer (Analog)

DVD player with

SCART OUT Stereo Amplifi er

DVD player with HDMI out

Computer (Digital)

*: Multiple monitors that are daisy-chained have a limit to the connectable monitors.

NOTE: Solid lines = video signal. Dotted lines = audio signal.

VCR or

DVD Player

DVD player

Connected equipment

AV

PC

Connecting terminal

Setting in Terminal Mode

DVI (DVI-D)

HDMI

5BNC+VIDEO

VIDEO1 (BNC)

DVI MODE: DVI-HD

RAW/EXPAND* 1

BNC MODE: SCART

-

S-VIDEO

VIDEO2 (5BNC)

-

BNC MODE: VIDEO

DVD/HD (5BNC) BNC MODE: COMPONENT

VGA (D-Sub)

DVI (DVI-D)

-

DVI MODE: DVI-PC

RGB/HV (5BNC)

DisplayPort

HDMI

BNC MODE: RGB

-

RAW/EXPAND* 1

Input signal name

DVI

HDMI

SCART

VIDEO1

S-VIDEO

VIDEO2

DVD/HD

VGA

DVI

RGB/HV

DPORT

HDMI

*1: depend on signal type.

Connecting

Audio terminal

AUDIO IN1, IN2, IN3

HDMI

AUDIO IN1, IN2, IN3

AUDIO IN1, IN2, IN3

AUDIO IN1, IN2, IN3

AUDIO IN1, IN2, IN3

AUDIO IN1, IN2, IN3

AUDIO IN1, IN2, IN3

AUDIO IN1, IN2, IN3

AUDIO IN1, IN2, IN3

DPORT

HDMI

Input button in remote control

DVI

HDMI

DVD/HD

VIDEO

S-VIDEO

VIDEO

DVD/HD

VGA

DVI

RGB/HV

DISPLAYPORT

HDMI

• AUDIO IN 1, 2 and 3 can be used for audio input. To select audio source [IN1], [IN2] or [IN3] in AUDIO INPUT in OSD menu or press the AUDIO INPUT button (remote control).

English-15

Connecting a Personal Computer

Connecting your computer to your LCD monitor will enable you to display your computer’s screen image.

Some video cards with a pixel clock over 162MHz may not display an image correctly.

Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.

<Typical factory preset signal timing>

Resolution

640 x 480

800 x 600

1024 x 768

1280 x 768

1360 x 768

1280 x 1024

1600 x 1200

1920 x 1080

Scanning frequency

Horizontal

31.5 kHz

Vertical

60 Hz

37.9 kHz

48.4 kHz

48 kHz

48 kHz

64 kHz

75 kHz

67.5 kHz

60 Hz

60 Hz

60 Hz

60 Hz

60 Hz

60 Hz

60 Hz

Remarks

Compressed image

Recommended resolution

• If you use with a Macintosh PowerBook, set “Mirroring” to Off on your PowerBook.

Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any special identifi cation or confi guration your monitor’s image and monitor may require.

• Input TMDS signals conforming to DVI standards.

• To maintain display quality, use a cable that conforms to DVI standards.

Connecting a DVD Player or Computer with HDMI out

• Please use an HDMI cable with HDMI logo.

• It may take a moment for the signal to appear.

• Some video cards or drivers may not display an image correctly.

Connecting a Computer with DisplayPort

• Please use DisplayPort cable with DisplayPort certifi ed logo.

• It may take a moment for the signal to appear.

• Please note that DisplayPort connector does not supply power to the connected component.

• Please note that when connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not appear.

• Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.

English-16

Basic Operation

Power ON and OFF Modes

The LCD monitor power indicator will turn green while powered on and will turn red while powered off.

NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the

Power Button on the front of the LCD.

OFF

ON

Main Power Switch

Power Button

Using the remote control

Power Button

English-17

Power Indicator

Mode Status Indicator Light

Power ON

Power OFF

Power consumption under 0.5 W* 2

Green*

Red

1

Power Save

Power consumption under 1 W* 2

Power Standby when “SCHEDULE

SETTINGS” enabled

Red, Green

Red ON

Green Blinking

Diagnosis (Detecting failure) Red Blinking

(See Troubleshooting page 37)

*1 If “OFF” is selected in POWER INDICATOR (page 24), the LED will not light when the

LCD monitor is in active mode.

*2 Without any option, with factory settings, VGA input only.

Using Power Management

The LCD monitor follows the VESA approved DPM Display

Power Management function.

The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fi xed period.

The power management feature on your new display has been set to the “ON” mode. This allows your display to enter a Power Saving Mode when no signal is applied. This could potentially increase the life and decrease the power consumption of the display.

NOTE: Depending on the PC and video card used, this function may not operate.

NOTE: It takes about 10 minutes for monitor to go into power management mode when using HDMI,

DVD/HD, SCART, VIDEO1, VIDEO2, and

S-VIDEO.

Selecting a video source

To view a video source:

Use the input button to set [VIDEO1], [VIDEO2], [S-VIDEO].

Use the COLOR SYSTEM menu to set [AUTO], [NTSC],

[PAL], [SECAM], [PAL60], [4.43NTSC], according to your video format.

Picture Aspect

DVI, VGA, RGB/HV, DPORT

FULL 1:1 ZOOM NORMAL

HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO

FULL WIDE DYNAMIC 1:1 ZOOM NORMAL

Aspect ratio of image

Unchanged view* 3

Recommended selection for picture aspect* 3

NORMAL

4:3

DYNAMIC

FULL

Squeeze

WIDE

Letterbox

* 3 Grey areas indicate unused portions of the screen.

NORMAL: Displays the aspect ratio the same as it is sent from the source.

FULL: Fills entire screen.

WIDE: Expands a 16:9 letter box signal to fi ll entire screen.

DYNAMIC: Expands a 4:3 pictures to fi ll the entire screen with non-linearity. Some of the outside image area will be cut off due to expansion.

1:1: Display the image in a 1 by 1 pixel format.

ZOOM

The image can be expanded beyond the active display area.

The image which is outside of active display area is not shown.

ZOOM

ZOOM

English-18

Information OSD

The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc.

Press the DISPLAY button on the remote to bring up the Information OSD.

ID number assigned to current monitor* 1

ID number assigned monitor to be controlled via RS-232C* 2

Input Name

Audio input mode

Picture aspect

Input Signal Information

Sub picture information

*1: “IR CONTROL” should be set “Primary” or “Secondary”.

*2: “IR CONTROL” should be set “Primary”.

Picture Mode

DVI, VGA, RGB/HV, DPORT

STANDARD sRGB HIGHBRIGHT

HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO

STANDARD CINEMA HIGHBRIGHT

English-19

OSD (On-Screen-Display) Controls

NOTE: Some functions may not be available depending on the model or optional equipment.

Input source

Main Menu Icons

Main Menu Item

Sub Menu

PICTURE MODE

Select

70

50

50

50

50

THANK YOU FOR SAVING

THE ENVIRONMENT.

CARBON FOOTPRINT 86.0 %

Goto Adjustment Return Close

Key Guide

Adjustment Settings

Press UP or DOWN button to select sub-menu.

Press SET.

Press UP or DOWN,

PLUS or MINUS to select the function or setting to be adjusted.

Press MENU or EXIT.

Remote Control

Press UP or DOWN button to select.

Press INPUT button to decide.

Press UP or DOWN, PLUS or MINUS button to select.

Press EXIT

Control Panel

OSD screen

English-20

Setting

PICTURE

BACKLIGHT

Default

CONTRAST

SHARPNESS

BRIGHTNESS

HUE

Adjusts the overall image and background brightness. Press + or - to adjust.

Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.

Note: When sRGB is selected in picture mode, this function cannot be changed.

Adjusts the crispness of the image. Press + or - to adjust.

Adjusts the image brightness in relationship to the background. Press + or - to adjust.

Note: When sRGB is selected in picture mode, this function cannot be changed.

Adjusts the hue of the screen. Press + or - to adjust.

Note: When sRGB is selected in picture mode, this function cannot be changed.

70

50

50*

50

50

COLOR

COLOR TEMPERATURE Adjusts the color temperature of the entire screen. A low color temperature will make the screen reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B levels, CUSTOM must be showing as the COLOR TEMP selection.

Note: When sRGB is selected in picture mode, predefi ned 6500k is set so it cannot be changed.

When PROGRAMMABLE is selected in GAMMA CORRECTION, this function cannot be changed.

COLOR CONTROL

Adjusts the color depth of the screen. Press + or - to adjust.

Note: When sRGB is selected in picture mode, this function cannot be changed.

GAMMA CORRECTION

Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.

Note: When sRGB is selected in picture mode, this function cannot be changed.

Select a display gamma for best picture quality.

Note: When sRGB is selected in picture mode, this function cannot be changed.

NATIVE

2.2

2.4

S GAMMA

DICOM SIM.

PROGRAMMABLE

50*

10000K

0

Gamma correction is handled by the LCD panel.

Typical display gamma for use with a PC.

Good for video (DVD, etc.)

Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the image (S-Curve).

DICOM GSDF curve simulated for LCD type.

A programmable gamma curve can be loaded using NEC optional software.

NATIVE*

(except sRGB setting)

MOVIE SETTINGS

NOISE REDUCTION

VIDEO1, VIDEO2, S-VIDEO inputs only

Adjusts the amount of noise reduction. Press + or - to adjust.

6*

AUTO* TELECINE

HDMI, DVD/HD, SCART, VIDEO1,

VIDEO2, S-VIDEO inputs only

Automatically senses the sources frame rate for optimal picture quality.

ADAPTIVE CONTRAST

HDMI, DVD/HD, SCART, VIDEO1,

VIDEO2, S-VIDEO inputs only

Sets the level of adjustment for dynamic contrast.

PICTURE MODE

RESET

Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB] or [CINEMA]. See page 19.

Resets the following settings within the PICTURE menu back to factory setting: BACKLIGHT,

CONTRAST, SHARPNESS, BRIGHTNESS, HUE, COLOR, COLOR TEMPERATURE,

COLOR CONTROL, GAMMA CORRECTION, MOVIE SETTINGS.

ADJUST

AUTO SETUP

VGA, RGB/HV inputs only

Automatically adjusts Screen Size, H position, V position, Clock, Phase and White Level.

AUTO ADJUST

VGA, RGB/HV inputs only

H POSITION

All inputs except DVI, HDMI, DPORT

H Position, V Position and Phase are adjusted automatically when new timing is detected.

V POSITION

All inputs except DVI, HDMI, DPORT

CLOCK

VGA, RGB/HV inputs only

Controls the horizontal position of the image within the Display area of the LCD.

Press + to move right. Press - to move left.

Controls the vertical position of the image within the Display area of the LCD.

Press + to move up. Press - to move down.

Press + to expand the width of the image on the right of the screen.

Press - to narrow the width of the image on the left.

Adjusts the visual “noise” on the image.

PHASE

VGA, RGB/HV, DVD/HD, SCART inputs only

*: depends on signal input

OFF

STANDARD

-

-

-

-

-

-

OFF

English-21

H RESOLUTION

VGA, RGB/HV inputs only

V RESOLUTION

VGA, RGB/HV inputs only

INPUT RESOLUTION

VGA, RGB/HV inputs only

ASPECT

NORMAL

FULL

WIDE

DYNAMIC

1:1

ZOOM

ZOOM

H ZOOM

V ZOOM

H POS

V POS

RESET

AUDIO

VOLUME

BALANCE

TREBLE

BASS

SURROUND

PIP AUDIO

LINE OUT

AUDIO INPUT

Adjusts the horizontal size of the image.

Adjusts the vertical size of the image.

-

-

If there is a problem with signal detection, this function forces the monitor to display the signal at the desired resolution. After selection, execute “AUTO SETUP” if required.

If no problem is detected, the only available option will be “AUTO”.

Select the aspect ratio of the screen image.

Displays the aspect ratio the same as it is sent from the source.

Fills entire screen.

Expands a 16:9 letter box signal to fi ll entire screen.

Expands a 4:3 pictures to fi ll the entire screen with non-linearity. Some of the outside image area will be cut off due to expansion.

Display the image in a 1 by 1 pixel format. (If the input resolution is higher than a 1920 x 1080 resolution, the image will be scaled down to fi t the screen.)

The image can be expanded beyond the active display area. The image which is outside of active display area is not shown.

Maintains the aspect ratio while zooming.

Amount of horizontal zoom.

Amount of vertical zoom.

Horizontal position.

Vertical position.

Resets the following settings within the ADJUST menu back to factory setting: AUTO ADJUST,

H POSITION, V POSITION, CLOCK, PHASE, H RESOLUTION, V RESOLUTION, ASPECT.

AUTO

NORMAL

-

-

-

-

-

-

-

-

Increases or decreases output volume level.

Adjust the balance of L/R volume.

Press + button to move the stereo sound image to right.

Press - button to move the stereo sound image to left.

To accentuate or reduce the high frequency sound.

Press + button to increase TREBLE sound.

Press - button to decrease TREBLE sound.

To accentuate or reduce the low frequency sound.

Press + button to increase BASS sound.

Press - button to decrease BASS sound.

Artifi cial surround sound.

Note: Audio out is disabled when this function is set to ON.

Selects source of PIP audio.

Selecting “VARIABLE” enables control of the line out level with the VOLUME button.

Note: LINE OUT is disabled when SURROUND is set to ON.

Selects audio input source [IN1], [IN2], [IN3], [DPORT], [HDMI], [OPTION]*.

RESET

SCHEDULE

OFF TIMER

Resets “AUDIO” options back to factory settings except VOLUME.

SCHEDULE SETTINGS

SCHEDULE LIST

DATE & TIME

Sets the monitor to power off after a length of time.

A time between 1 to 24 hours is available.

Creates a working schedule for the monitor to use.

List of schedules.

Sets the date, time, and daylight saving region. Date & time must be set in order for the

“SCHEDULE” function to operate. See page 28.

Confi gures the year for the real time clock.

YEAR

MONTH

DAY

Confi gures the month for the real-time clock.

Confi gures the day for the real-time clock.

*: The product you purchased may not have this feature.

-

CENTER

0

0

OFF

MAIN AUDIO

FIXED

Depend on signal input

-

OFF

-

-

-

-

-

English-22

TIME

DAYLIGHT SAVING

RESET

PIP

KEEP PIP MODE

PIP MODE

OFF

PIP

POP

PICTURE BY

PICTURE-ASPECT

PICTURE BY

PICTURE-FULL

PIP SIZE

SMALL

MIDDLE

LARGE

PIP POSITION

ASPECT

TEXT TICKER

MODE

POSITION

SIZE

BLEND

DETECT

FADE IN

SUB INPUT

RESET

OSD

LANGUAGE

ENGLISH

DEUTSCH

FRANÇAIS

ITALIANO

ESPAÑOL

SVENSKA

РУССКИЙ

Confi gures the time for the real-time clock.

Confi gures daylight savings on or off.

Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER,

SCHEDULE SETTINGS.

Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off.

When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.

Selects Picture-in-Picture mode.

Normal mode.

Picture in Picture mode.

Picture out Picture mode.

Picture by picture (split screen) mode, with keep aspect.

Picture by picture (split screen) mode, with full screen.

Selects the size of the sub-picture used in Picture-in-Picture (PIP) mode.

Determines where the PIP appears on the screen.

Selects sub picture aspect, [FULL], [NORMAL] and [WIDE]. See page 18.

Enables Text Ticker and allows you to set Horizontal or Vertical direction.

Selects the location of the Text Ticker on the screen.

Determines the size of the Text Ticker in relationship to the overall screen size.

Sets the transparency of the Text Ticker (0: transparent, 100: opaque).

Enables auto-detection of the Text Ticker.

Enables fade-in of the text ticker.

Selects sub picture input signal.

Resets PIP options back to factory settings except ASPECT and SUB INPUT.

Select the language used by the OSD.

-

OFF

-

OFF

OFF

LARGE

X = 95, Y = 92

FULL

OFF

Depends on signal input

-

ENGLISH

(Depends on destination)

30 Sec.

X = 128, Y = 225

MENU DISPLAY TIME

OSD POSITION

UP

DOWN

LEFT

RIGHT

Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.

Determines the location where the OSD appears on the screen.

English-23

INFORMATION OSD

MONITOR INFORMATION

OSD TRANSPARENCY

OSD ROTATION

LANDSCAPE

PORTRAIT

INPUT NAME

CLOSED CAPTION

VIDEO1, VIDEO2, S-VIDEO inputs only

RESET

Selects whether the information OSD is displayed or not. The information OSD will be displayed when the input signal or source changes. The information OSD will also give a warning when there is no-signal or the signal is out-of range.

An interval between 3 to 10 seconds for the Information OSD to appear is available.

Indicates the model and serial number of your monitor.

CARBON SAVINGS: Display the estimated carbon saving information in kg. The carbon footprint factor in the carbon saving calculation is based on the OECD (2008 Edition).

Set the transparency of the OSD.

Determines the OSD display direction between landscape and portrait.

V651 display direction is landscape only.

ON, 3 Sec.

-

ON

LANDSCAPE

Display the OSD with landscape mode.

Display the OSD with portrait mode.

You can create a name for the INPUT currently being used.

Max: 8 characters, including Space, A-Z, 0-9, and some symbols.

Activates closed captioning.

-

OFF

Resets the following settings within the OSD menu back to factory setting:

MENU DISPLAY TIME, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY,

CLOSED CAPTION.

-

MULTI DISPLAY

CONTROL ID 1

IR CONTROL

NORMAL

PRIMARY

SECONDARY

LOCK

TILE MATRIX

H MONITORS

V MONITORS

POSITION

TILE COMP

ENABLE

POWER ON DELAY

POWER INDICATOR

Sets the monitor ID number from 1-100 and group ID from A-J.

NOTE: Group ID is made of multiple selections.

Selects the mode of the monitor for use with the infra-red remote control when using the

RS-232C daisy chain.

The monitor will be controlled normally using the remote controller.

Choose “PRIMARY” for the fi rst monitor within an RS-232C daisy chain.

Choose “SECONDARY” for all subsequent monitors within an RS-232C daisy chain.

Prevents the monitor from being controlled by the wireless remote controller. To return to normal operation, press the “DISPLAY” button on the remote controller for 5 seconds.

Allows one image to be expanded and displayed over multiple screens (up to 100) through a distribution amplifi er.

NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate without a distribution amplifi er at a lower number of screens.

The ZOOM setting of ASPECT becomes invalid.

Number of monitors arranged horizontally.

Number of monitors arranged vertically.

Select which section of the tiled image to be displayed on the monitor.

Turns the TILE COMP feature on.

Enables Tile Matrix.

Adjusts the delay time between being in “standby” mode and entering “power on” mode.

“POWER ON DELAY” can be set between 0 and 50 seconds.

Turns ON or OFF the LED located at the front of the monitor.

If “OFF” is selected, LED will not light when the LCD monitor is in active mode.

NORMAL

1

1

1

NO

NO

0 Sec.

ON

EXTERNAL CONTROL

CONTROL

LAN RESET

ID=ALL REPLY

MAC ADDRESS

Selects the control interface, RS-232C or LAN.

Resets the LAN settings.

When controlling the monitor externally, select if the communication command, which specifi es destination equipment ID (ALL or GROUP ID), is replying or not. When you need reply, please select “ON”.

If you connect the multiple monitors that are daisy-chained from second monitor by RS-232C, you need to select “OFF” from second monitor.

Displays the MAC ADDRESS.

RS-232C

-

OFF

-

English-24

LAN SETTING

DHCP

IP ADDRESS

SUBNET MASK

DEFAULT GATEWAY

DNS PRIMARY

DNS SECONDARY

SETTING COPY

COPY START

ALL INPUT

Set your subnet mask number of the network connected to the monitor when “DISABLE” is selected for [DHCP].

Set your default gateway of the network connected to the monitor when “DISABLE” is selected for [DHCP].

Set your primary DNS settings of the network connected to the monitor.

Set your secondary DNS settings of the network connected to the monitor.

In a daisy chain scenario, select the OSD menu categories that you want to copy over to the other monitor.

NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C”.

This function resets to default when power is off. This function has a limit depending on the cable you use.

Select “YES” and press the SET button to start copying.

All input terminals settings are copied when you select this item. Default is off.

255.255.255.0

192.168.0.1

0.0.0.0

0.0.0.0

NO

RESET Resets “MULTI DISPLAY” options back to factory settings except LAN SETTING.

DISPLAY PROTECTION

POWER SAVE Sets how long the monitor waits to go into power save mode after the signal is lost.

Note: When connecting DVI, the video card might not stop sending the digital data even though the image might have disappeared. If this occurs the monitor will not switch into power management mode.

ON

HEAT STATUS

FAN CONTROL

SCREEN SAVER

GAMMA

BACKLIGHT

MOTION

SIDE BORDER COLOR

When you use this function, EXTERNAL CONTROL should be “LAN”.

NOTE: When changing the LAN SETTING, turn the monitor off and then back on.

After turning on the monitor, you need to wait several seconds until the LAN SETTING is applied.

Enabling this option automatically assigns an IP address to the monitor from your DHCP server.

Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator.

NOTE: Consult your network administrator for the IP address when “ENABLE” is selected for

[DHCP].

Set your IP address of the network connected to the monitor when “DISABLE” is selected for

[DHCP].

DISABLE

192.168.0.10

Displays status of the FAN, BACKLIGHT and TEMPERATURE.

Cooling fan reduces the temperature of the display to protect from overheating.

If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.

Use the SCREEN SAVER function to reduce the risk of Image Persistence.

The display gamma is changed and fi xed when “ON” is selected.

The brightness of backlight is decreased when “ON” is selected.

The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at user determined intervals. You can set interval time and zooming ratio.

This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.

Adjusts the color of the side borders when a 4:3 image is displayed.

Press + button, the bar will become lighter.

Press - button, the bar will become darker.

Adjusts the brightness level according to the input signal.

-

AUTO

OFF

OFF

OFF

15

OFF AUTO BRIGHTNESS

DPORT, DVI, VGA, RGB/HV inputs only

CHANGE SECURITY

PASSWORD

SECURITY

DDC/CI

ALERT MAIL

RESET

Allows the security password to be changed.

The factory preset password is 0000.

Locks the security password.

ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.

Selects whether or not to send an e-mail notifi cation of monitor error via wired LAN.

Resets the following settings within the DISPLAY PROTECTION menu back to factory setting: POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR,

AUTO BRIGHTNESS, DDC/CI.

-

OFF

ENABLE

OFF

-

English-25

ADVANCED OPTION

INPUT DETECT Selects the method of input detection the monitor uses when more than two input devices are connected.

NONE

FIRST DETECT

The Monitor will not search the other video input ports.

When the current video input signal is not present, then the monitor searches for a video signal from the other video input port. If the video signal is present in the other port, then the monitor switches the video source input port to the new found video source automatically.

The monitor will not look for other video signals while the current video source is present.

LAST DETECT

VIDEO DETECT

CUSTOM DETECT

INPUT CHANGE

When the monitor is displaying a signal from the current source and a new secondary source is supplied to the monitor, the monitor will automatically switch to the new video source. When current video input signal is not present, the monitor searches for a video signal from the other video input port. If the video signal is present in the other port, then the monitor switches the video source input port to the new found video source automatically.

DVD/HD, SCART, VIDEO1, VIDEO2 or S-VIDEO inputs will have priority over DVI, VGA,

RGB/HV. When DVD/HD, SCART, VIDEO1, VIDEO2 or S-VIDEO input signal is present the monitor will change and keep to the DVD/HD, SCART, VIDEO1, VIDEO2 or S-VIDEO input.

Set the priority of input signals.

When CUSTOM DETECT is selected, monitor searches listed inputs only.

Sets input change speed.

NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed.

This function should be chosen after all adjustment options have been made for the input.

TERMINAL SETTING

DVI MODE

BNC MODE

HDMI SIGNAL

DEINTERLACE

ON

OFF

Selects the kind of DVI-D equipment which is connected to the DVI input. Select “DVI-PC” when

PC or other computer equipment is connected. Select “DVI-HD” when DVD player, which has

DVI-D output, is connected.

Selects the type of signal associated with the BNC input.

RGB: Analog input (R, G, B, H, V)

COMPONENT: Component (Y, Cb/Pb, Cr/Pr)

SCART: SCART signal

VIDEO: Composite video (VIDEO2)

RAW: Disable the expanded feature.

EXPAND: Expand image contrast and increase detail in the dark and bright areas.

Selects the IP (Interlace to Progressive) conversion function.

Note: For DVI input “DVI-HD” needs to be enabled in the DVI mode menu.

Converts interlaced signals to progressive. This is the default setting.

Disables IP conversion. This setting is best suited for motion pictures, but increases the risk of image retention.

The selected Color System depends on the video format of the input signal.

COLOR SYSTEM

VIDEO1, VIDEO2, S-VIDEO inputs only

AUTO

NTSC

PAL

SECAM

4.43 NTSC

PAL-60

Automatically chooses Color System setting based on input signal.

NONE

NORMAL

DVI-PC

RGB

EXPAND

ON

AUTO

English-26

OVER SCAN

HDMI, DVD/HD, SCART, VIDEO1, VIDEO2,

S-VIDEO inputs only

ON

OFF

OPTION SETTING

OPTION POWER

INTERNAL PC

OFF WARNING

AUTO OFF

START UP PC

FORCE QUIT

120Hz

(not adjustable)

MURA COMP

(not adjustable)

RESET

Some video formats may require different scanning modes in order to best display the image.

Image size is larger than what can be displayed. The image edge will appear cropped.

Approximately 95% of the image will be shown on the screen.

Image size stays within the display area. The whole image is displayed on the screen.

NOTE: When you use a computer with HDMI out, please set “OFF”.

You can set this setting when option board accessory is connected to the monitor.

Please contact your supplier for detailed information about Option board slot accessories.

Allow the monitor to supply power to Option board slot during power save mode or standby mode.

The function is available for OPS based PC.

If OPTION POWER is OFF, a warning message appears when monitor power is turned off.

Monitor power is automatically “OFF” when connected PC is OFF or the monitor is in power save mode.

When ON is selected, connected PC start-up.

When ON is selected, it performs force quit PC.

FACTORY RESET

Resets the following settings within the ADVANCED OPTION menu back to factory setting:

INPUT DETECT (except the priority of input signals), INPUT CHANGE, TERMINAL SETTING,

DEINTERLACE, COLOR SYSTEM, OVER SCAN, START UP PC in OPTION SETTING and

FORCE QUIT in OPTION SETTING.

Resets OSD options back to factory settings EXCEPT FOR: PICTURE MODE, VOLUME,

SCHEDULE SETTINGS, DATE & TIME, ASPECT in PIP, SUB INPUT in PIP, LANGUAGE, OSD

ROTATION, CHANGE SECURITY PASSWORD and SECURITY.

ON

-

OFF

-

-

-

-

English-27

NOTE 1: CREATING A SCHEDULE

The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be programmed.

To program the schedule:

1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET or the + button to enter the

Settings menu. Highlight the desired schedule number and press set. The box next to the number will turn yellow. The schedule can now be programmed.

2. Use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set the hour. Use the up and down buttons to highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the same manner.

3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight

PIC. MODE. Use the + and - buttons to choose the picture mode.

4. Use the down button to select a day on which the schedule will be enabled. Push the set button to enable. If the schedule is to be ran every day, choose EVERY DAY and press the SET button. The circle next to EVERY DAY will turn yellow. If a weekly schedule is desired, choose the days of the week using the up and down buttons and pressing SET to select. Then highlight the EVERY WEEK option and press SET.

5. After a schedule is programmed the remaining schedules can then be set. Press MENU to leave the OSD or press EXIT to go back to the previous menu.

Note: If schedules are overlapping then the schedule with the highest number will have priority over the schedule with the lowest number. For example schedule #7 will have priority over schedule #1.

If selected input or picture mode is not available now, disable input or picture mode is shown in red.

DVI

SCHEDULE:

OFF TIMER

SCHEDULE SETTINGS

SCHEDULE LIST

DATE & TIME

RESET RESET

Choose

SETTINGS:

(THU) JUN.18.2009 15:38

1 2 3 4 5 6 7

ON:

OFF:

INPUT:

PIC. MODE:

– – : – –

– – : – –

– – – –

– – – –

EVERY DAY

EVERY WEEK

MON TUE WED THU

FRI SAT SUN

Mark Return Close

NOTE 2: IMAGE PERSISTENCE

Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of time should be avoided.

To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.

For long life use as Public Display

Image Sticking of LCD Panel

When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or

“ghost” image of previous image may be observed. (Image Persistence)

Image Persistence is not permanent, but when fi xed image is displayed for long period, ionic impurities inside LCD are accumulated along the displayed image, and may be permanent. (Image Sticking)

Recommendations

To prevent Image Sticking, and for longer life usage of LCD, the following are recommended.

1. Fixed image should not be displayed for long period. Change fi xed images after short intervals.

2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions.

3. Lower environmental temperatures prolong the lifespan of the monitor.

When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor are stacked, utilize the temperature sensors inside monitor.

To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness.

4. Please use “Screen Saver Mode” of monitor.

English-28

Remote Control Function

REMOTE CONTROL ID FUNCTION

REMOTE CONTROL ID

The remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors. For example: if there are many monitors being used in the same area, a remote control in normal mode would send signals to every monitor at the same time (see

Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate one specifi c monitor within the group (see Figure 2).

Monitor ID:1

Remote works

Monitor ID:2

Remote works

Figure 1

Remote in

Normal mode or the REMOTE ID is set to 0

TO SET REMOTE CONTROL ID

While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to input the Monitor ID (1-100) of the display to be controlled via remote. The remote can then be used to operate the monitor having that specifi c Monitor ID number.

When 0 is selected or when the remote control is in normal mode, all monitors will be operated.

Monitor ID:1 Monitor ID:2

Monitor ID:3

Remote works

Monitor ID:3

TO SET/RESET REMOTE CONTROL MODE

ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for

2 seconds.

Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold down for 2 seconds.

In order for this feature to work properly, the display must be assigned a Monitor ID number.

The Monitor ID number can be assigned under the MULTI DISPLAY menu in the OSD

(See page 24).

Point the remote control towards the remote sensor of the desired monitor and press the

REMOTE ID SET button. The MONITOR ID number is shown on the display when your remote control is in ID mode.

Remote does not work

Remote does not work

Figure 2

Remote set up to use REMOTE

ID:3

Remote works

Use the remote control to operate a monitor that has a specifi c MONITOR ID number assigned to it.

1. Set the MONITOR ID number for the display (See page 24). The MONITOR ID number can range from 1-100.

This MONITOR ID number allows the remote control to operate this specifi c monitor without affecting other monitors.

2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number

(1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to simultaneously control all displays in range.

3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.

The MONITOR ID number is shown in red on the display.

If the REMOTE CONTROLID is “0”, then all displays in range will show their respective MONITOR ID number in red.

If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.

This LCD monitor can be controlled via personal computer or wireless remote control using an RS-232C connection.

MONITOR ID and IR CONTROL

Using one PC or one infrared wireless controller, up to 100 individual LCD monitors can be controlled through a daisy chain via RS-232C connection.

1. Connect PC and LCD monitors.

Connect a PC’s RS-232C control output to the LCD monitor RS-232C input. You can then connect the RS-232C output from the LCD monitor to another LCD monitor RS-232C input. Up to 100 monitors can be connected using RS-232C.

2. Set Monitor ID and IR Control mode.

For proper operation, the Monitor ID should be set in the OSD menu of each monitor that is in the chain. The Monitor ID can be set under the

“MULTI DISPLAY” menu in the OSD. The Monitor ID number can be set within a range from 1 to 100. No two monitors should share the same

Monitor ID number. It is recommended to number each monitor in a daisy chain sequentially from 1. The fi rst monitor in the daisy chain is designated as the primary monitor. Subsequent monitors with the chain are secondary monitors.

In the “ADVANCED OPTION” menu on the fi rst monitor in the RS-232C daisy chain set the “IR CONTROL” to “PRIMARY”.

Set the “IR CONTROL” to “SECONDARY” on all other monitors.

English-29

3. Press the “DISPLAY” button on the remote control while aiming at the “PRIMARY” monitor. The Information OSD will be shown at top left side of the screen.

Monitor ID: Displays the ID number of the current monitor within the daisy chain.

Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor.

Press the “+” or “-” buttons to change the “Target ID” to show the ID number of the monitor to be controlled. To control the entire daisy chained monitors simultaneously, select “ALL” as the “Target ID.”

4. Use the wireless remote controller to control the “SECONDARY” monitor while aiming at the “PRIMARY” monitor.

The “MENU OSD” will appear on the selected target monitor.

NOTE: If the “ID No.” mode select OSD is showing, press the “DISPLAY” button on the remote control while pointing at the “PRIMARY” monitor to clear this OSD.

HINT: If you lost control due to the incorrect setting of “IR CONTROL”, pressing the “DISPLAY” button on the remote control for 5 or more seconds will reset the “IR CONTROL” menu to “NORMAL” function.

WIRED REMOTE CONTROL FUNCTION

You can control this monitor by connecting REMOTE IN/OUT with Stereo Mini plug cable (3.5 ).

MultiSync MultiSync

OUT

Remote IN Remote OUT Remote IN

IN

Remote control cable Remote control cable

NOTE: Turn off the main power switch before connect/disconnect Stereo Mini plug cable.

NOTE: Do not use this connector unless specifi ed.

Remote OUT

MultiSync

English-30

Controlling the LCD monitor via RS-232C Remote Control

This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.

NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C” (See page 24).

Functions that can be controlled by a personal computer are:

• Power ON or OFF

• Switching between input signals

Connection

LCD Monitor + PC

MultiSync MultiSync

PC

(Out)

OUT

IN

RS-232C Cable

RS-232C (IN) RS-232C (OUT)

RS-232C Cable

RS-232C (IN) RS-232C (OUT)

MultiSync

NOTE: If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your dealer for details.

Check the “ID=ALL REPLY” setting in “EXTERNAL CONTROL”.

* In order to function, the RS-232C OUT terminal can only be connected to another monitor of the same model.

Do not connect to other types of equipment.

To control monitor or multiple monitors that are daisy-chained together please use the control command. Instructions for the control command can be found on the CD included with the display. The fi le is called “External_control.pdf”.

Multiple monitors that are daisy-chained have a limit to the conectable monitor.

1) Interface

PROTOCOL

BAUD RATE

DATA LENGTH

PARITY BIT

RS-232C

9600 [bps]

8 [bits]

NONE

STOP BIT 1 [bit]

FLOW CONTROL NONE

This LCD monitor uses RXD, TXD and GND lines for RS-232C control.

The reverse type cable (null modem cable) (not include) should be used for RS-232C control.

2) Control command diagram

Please see fi le “External_Control.pdf” on the CD-ROM.

English-31

Controlling the LCD monitor via LAN Control

Connecting to a Network

Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.

NOTE: When you use this function, EXTERNAL CONTROL should be “LAN” (See page 24).

To use a LAN connection, you are required to assign an IP address.

Example of LAN connection:

Server

NOTE: Use a category 5 or higher LAN cable.

Hub

LAN cable (not supplied)

Network Setting by Using an HTTP Browser

Overview

Connecting the monitor to a network allows for monitor control from a computer via the network.

To perform the monitor control from a web browser, you must have an exclusive application installed on your computer.

The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP server function. Please be sure to use “Microsoft Internet Explorer 6.0” or a higher version for the web browser.

(This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will vary depending on the version of browser. Please refer to the help fi les and the other information provided in your software.)

Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the monitor and entering the following URL.

Network Setting http://<the Monitor’s IP address>/index.html

TIP: The default IP address is “192.168.0.10”.

The exclusive application can be downloaded from our website.

NOTE: If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to refresh your web browser (or clear the cache).

The display or button’s response can be slowed down or operation may not be accepted depending the settings of your network. Should this happen, consult your network administrator.

The LCD monitor may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and repeat. If you still can’t get a response, turn the monitor off and then back on.

English-32

Preparation Before Use

Connect the monitor to a commercially available LAN cable before engaging in browser operations.

Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be refl ected in operation.

It is recommended that a proxy server not be used unless it is unavailable.

Handling of the Address for Operation via a Browser

The host name can be used under the following cases:

If the host name corresponding to the IP address of the monitor has been registered to the domain name server (DNS) by the network administrator, you can then access the network settings of the display via that registered host name using a compatible browser.

If the host name corresponding to the IP address of the monitor has been confi gured in the “HOSTS” fi le of the computer being used, you can then access the network settings of the display via that host name using a compatible browser.

Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL.

Example 2: When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying

http://192.168.73.1/index.html for the address or the entry column of the URL.

Network Settings

http://<the Monitor’s IP address> /index.html

DHCP Enabling this option automatically assigns an IP address to the monitor from your DHCP server.

Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator.

NOTE: Consult your network administrator for the IP address when [ENABLE] is selected for

[DHCP].

Set your IP address of the network connected to the monitor when [DISABLE] is selected for [DHCP].

IP v4 Address

Subnet Mask

Default Gateway

Set your subnet mask number of the network connected to the monitor when [DISABLE] is selected for [DHCP].

Set your default gateway of the network connected to the monitor when [DISABLE] is selected for

[DHCP].

Set your primary DNS settings of the network connected to the monitor.

Primary DNS

Secondary DNS

Apply

Set your secondary DNS settings of the network connected to the monitor.

Refl ect your settings.

NOTE: Make sure to execute “the reboot” from the “reboot screen” or to turn the monitor off and then back on to enable the changing, after clicking [Apply].

NOTE: The following settings will reset back to the factory setting when “LAN reset” is selected by an EXTERNAL CONTROL of OSD:

[DHCP]: DISABLE, [IP v4 Address]: 192.168.0.10, [Subnet Mask]: 255.255.255.0, [Default Gateway]: 192.168.0.1 but

[Primary DNS] and [Secondary DNS] are not changed.

English-33

Alert Mail Setting

http://<the Monitor’s IP address>/lanconfi g.html

This option notifi es your computer of an error message via e-mail when using wired LAN. An error message notifi cation will be sent when an error occurs in the monitor.

Alert Mail Checking [ENABLE] will turn on the Alert Mail feature.

Checking [DISABLE] will turn off the Alert Mail feature.

Host Name

Domain Name

Type in the hostname of the network connected to the monitor.

Up to 60 alphanumeric characters can be used.

Type in the domain name of the network connected to the monitor.

Up to 60 alphanumeric characters can be used.

Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.

Sender’s Address

SMTP Server Type in the SMTP server name to be connected to the monitor.

Up to 60 alphanumeric characters can be used.

Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.

Recipient’s Address

1 to 3

Authentication Method This selects the authentication method of the e-mail transmission.

POP3 Server This specifi es the address of the POP3 server that is used in the authentication of the e-mail.

User Name This sets the user name for logging into the authentication server when authentication is required for the e-mail transmission. Up to 60 alphanumeric characters can be used.

Password

TestMail

This sets the password for logging into the authentication server when authentication is required for the e-mail transmission. Up to 60 alphanumeric characters can be used.

Click this button to send a test mail to check if your settings are correct.

Apply Click this button to refl ect the above settings.

NOTE: Make sure to execute “the reboot” from the “reboot screen” or to turn the monitor off and then back on to enable the changing, after clicking [Apply].

NOTE: • If you execute a test, you may not receive an Alert mail.

Should this happen, check if the network settings are correct.

• If you entered an incorrect address in a test, you may not receive an Alert mail.

Should this happen, check if the Recipient’s Address is correct.

TIP: The Alert Mail settings will not be affected even when [RESET] is done from the menu.

For Control command diagram, please see fi le “External_Control.pdf” on the CD-ROM.

English-34

Alert error message list

Error number

* ErrorCode

70h ~ 7Fh

80h ~ Fh

90h ~ 9Fh

A0h ~ AFh

A2h

B0h ~ BFh

C0h ~ CFh

Alert mail Message Explanation Measure

The monitor’s power supply is not functioning normally.

The cooling fan has stopped.

The monitor’s back light unit is not functioning normally.

The monitor is overheated.

Standby power Abnormal

Cooling fan Abnormal

Backlight abnormal

Please contact your supplier.

Please contact your supplier.

Please contact your supplier.

The monitor doesn’t have the input signal.

The monitor caused the problem of the abnormal of option board.

Temperature Abnormal

SENSOR reached at the temperature that the user had specifi ed.

Please contact your supplier.

Reconfi rm the setting condition from

OSD (DISPLAY PROTECTION-FAN

CONTROL) or please contact your supplier.

*condition: DISPLAY PROTECTION-FAN

CONTROL-COOLING FAN = AUTO

No signal

Option board abnormal

Please check “No picture” in

“Troubleshooting”.

Please contact your supplier.

Sample: The following examples are content of Alert Mail that informs the temperature anomaly of monitor.

Sample: The following examples are content of test mail by browser.

English-35

Features

Reduced Footprint: Provides the ideal solution for environments with superior image quality.

Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards.

OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides the monitor with a uniform color profi le. This assures that the colors displayed on the monitor are exactly the same as on the color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen and customise the color accuracy of your monitor to a variety of standards.

sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays and other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and backward compatibility with other common color standards.

OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use on-screen menus.

Plug and Play: The Microsoft ® solution with the Windows ® operating system facilitates setup and installation by allowing the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically optimizing display performance.

IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and lowering the air conditioning costs of the workplace.

FullScan Capability: Allows you to use the entire screen area in most resolutions, signifi cantly expanding image size.

VESA Standard (FDMIv1) Mounting Interface: Allows you to connect your LCD monitor to any VESA standard (FDMIv1) third party mounting arm or bracket. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America.

DVI-D: The digital-only subset of DVI ratifi ed by the Digital Display Working Group (DDWG) for digital connections between computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital connectors such as DFP and P&D. The DVI interface of this display supports HDCP.

TILE MATRIX, TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width.

ZOOM: Expands image size for horizontal and vertical direction.

RS-232C daisy chain: You can control the multiple monitors by controller or wireless remote controller.

Self-diagnosis: If an internal error should occur, a failure state will be indicated.

HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over a Digital Visual Interface (DVI). If you are unable to view material via the DVI input, this does not necessarily mean the display is not functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).

Option board slot: You can use an option board, which is compliant with Intel's OPS standard. Please contact your supplier for detailed information.

English-36

Troubleshooting

No picture

• The signal cable should be completely connected to the display card/computer.

• The display card should be completely seated in its slot.

• Check the main Power Switch, it should be in the ON position.

• Front Power Switch and computer power switch should be in the ON position.

• Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.)

• Check the monitor and your display card with respect to compatibility and recommended settings.

• Check the signal cable connector for bent or pushed-in pins.

Power Button does not respond

• Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.

• Check the main Power Switch on the back side of the monitor.

Image persistence

• Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image

Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed.

For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

NOTE: As with all personal display devices, NEC DISPLAY

SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

Image is unstable, unfocused or swimming is apparent

• Signal cable should be completely attached to the computer.

• Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fi ne adjustment.

When the display mode is changed, the OSD Image Adjust settings may need to be re-adjusted.

• Check the monitor and your display card with respect to compatibility and recommended signal timings.

• If your text is garbled, change the video mode to noninterlace and use 60Hz refresh rate.

Image of component signal is greenish

• Check to see if the DVD/HD input connector is selected.

LED on monitor is not lit

(no green or red color can be seen)

• Power Switch should be in the ON position and power cord should be connected.

• Check the main Power Switch, it should be in the ON position.

• Make certain the computer is not in a power-saving mode

(touch the keyboard or mouse).

• Check to see that the power indicator option in the OSD is set to ON.

RED LED on monitor is blinking

• A certain failure might have occurred, please contact your nearest authorized NEC DISPLAY SOLUTIONS service facility.

• If the monitor is powered off by the inside temperature being higher than the normal operating temperature, a RED

LED will blink six times. Power on the display again after confi rming the inside temperature has been reduced to normal operation temperature.

Display image is not sized properly

• Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.

• Check to make sure that a supported mode has been selected on the display card or system being used.

(Please consult display card or system manual to change graphics mode.)

Selected resolution is not displayed properly

• Use OSD Display Mode to enter Information menu and confi rm that the appropriate resolution has been selected. If not, select corresponding option.

No Sound

• Check to see if audio cable is properly connected.

• Check to see if mute is activated.

• Check to see if volume is set at minimum.

• Check to see if computer supports an audio signal through

DisplayPort.

If unsure, contact the computer manufacturer.

• Check to see if SURROUND is ON.

• Check Internal/External speaker switch.

Remote Control is not available

• Check the Remote Control’s batteries status.

• Check if batteries are inserted correctly.

• Check if the Remote Control is pointing at the monitor’s remote sensor.

• Check the Remote Control Mode status.

• The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the LCD monitor, or when there is an object in the path.

“SCHEDULE”/“OFF TIMER” function is not working properly

• The “SCHEDULE” function will be disabled when the “OFF

TIMER” is set.

• If the “OFF TIMER” function is enabled and the power to the LCD monitor is turned off when the power supply is interrupted unexpectedly, then the “OFF TIMER” will be reset.

Snowy Picture, Poor Sound in TV

• Check antenna/cable connection. Use new cable if necessary.

Interference in TV

• Check components for shielding, move away from monitor if necessary.

RS-232C or LAN control is not available

• Check RS-232C or LAN cable connection.

• Check “CONTROL” setting in “EXTERNAL CONTROL”.

• Check the “ID=ALL REPLY” setting in “EXTERNAL

CONTROL”.

Either light vertical or horizontal stripes may appear, depending on the specifi c display pattern. This is no product fault or degradation.

English-37

Specifi cations - V422

Product Specifi cations

LCD Module

Frequency

Pixel Pitch:

Resolution:

Color:

Brightness:

Contrast Ratio:

Viewing Angle:

42”/1067 mm diagonal

0.485 mm

1920 x 1080

Over 16 million colors (depending on video card used)

500 cd/m 2 (Max.), 370 cd/m 2 (Factory setting Typ.) @25°C

1300:1

89° (typ) @ CR>10

Horizontal:

Vertical:

15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)

31.5 kHz - 91.1 kHz (Digital Input)

50.0 - 85.0 Hz

25.2 MHz - 162.0 MHz

930.2 x 523.3 mm

Pixel Clock

Viewable Size

Input Signal

DVI DVI-D 24pin

DisplayPort DisplayPort Connector Digital RGB

VGA

RGB/HV*

HDMI

DVD/HD*

VIDEO1

VIDEO2*

S-VIDEO

2

2

2

15pin Mini D-sub

BNC (R,G,B,H,V)

HDMI Connector

BNC X 3

BNC

BNC

Mini DIN 4 pin

Digital RGB

Analog RGB

Sync

Analog RGB

Sync

Digital YUV

Digital RGB

Component

Composite

S-VIDEO

DVI (HDCP)

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920X1080 (60Hz), 1080p, 1080i

DisplayPort Complies with Standard V1.1a, applicable to HDCP V1.3

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920x1080 (60 Hz), 1080p, 1080i,

720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

HDMI

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920x1080 (60 Hz), 1080p, 1080i,

720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz

Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm

HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz

1.0 Vp-p/75 ohm

NTSC/PAL/SECAM/4.43NTSC/PAL60

Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)

NTSC/PAL/SECAM/4.43NTSC/PAL60

Output Signal

DVI

VIDEO1

DVI-D 24pin

BNC

Digital RGB

Composite

DVI (HDCP)

1.0 Vp-p with 75 ohm terminated

AUDIO

AUDIO

Input

RCA (L/R)

STEREO Mini Jack X2

HDMI Connector

Analog Audio

Digital Audio

DisplayPort Connector Digital Audio

Stereo L/R 0.5 Vrms

PCM 32, 44.1, 48 KHz (16/20/24bit)

PCM 32, 44.1, 48 KHz (16/20/24bit)

AUDIO

Output

Speaker Output

STEREO Mini Jack Analog Audio Stereo L/R 0.5 Vrms

Control

Power Supply

Operational Environment

Storage Environment

Dimension

Weight

VESA compatible mounting interface

Power Management

Plug & Play

Accessories

RS-232C In:

RS-232C Out:

LAN:

Remote IN:

Remote OUT:

External Speaker Jack 15 W + 15 W (8 ohm)

Internal Speaker 10W + 10W

9 Pin D-sub

9 Pin D-sub (with daisy chain)

RJ-45 10/100 BASE-T

Stereo Mini jack 3.5

Stereo Mini jack 3.5

1.2 - 2.8 A @ 100-240V AC, 50/60Hz

Temperature:

Humidity:

Altitude:

Temperature:

Humidity:

5 - 40°C / 41 - 104°F (Default brightness), 5 - 20°C / 41 - 68°F (Max brightness)

20 - 80% (without condensation)

0 - 3000 m (Brightness may decrease with altitude)

-20 - 60°C / -4 - 140°F

10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C

1022.9 (W) x 613.5 (H) x 105.6 (D) mm / 40.3 (W) x 24.2 (H) x 4.2 (D) inches

22.0 kg (48.5 lbs)

300 mm x 300 mm (M6, 4 Holes)

VESA DPM

VESA DDC2B, DDC/CI, DisplayPort

Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp x 2,

Screw x 2, CD-ROM, Thumbscrew for optional stand x 2

NOTE: Technical specifi cations are subject to change without notice. *1: Compressed image *2: Common terminal

English-38

Specifi cations - V462

Product Specifi cations

LCD Module

Frequency

Pixel Pitch:

Resolution:

Color:

Brightness:

Contrast Ratio:

Viewing Angle:

46”/1168 mm diagonal

0.530 mm

1920 x 1080

Over 16 million colors (depending on video card used)

450 cd/m 2 (Max.), 340 cd/m 2 (Factory setting Typ.) @25°C

3000:1

89° (typ) @ CR>10

Horizontal:

Vertical:

15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)

31.5 kHz - 91.1 kHz (Digital Input)

50.0 - 85.0 Hz

25.2 MHz - 162.0 MHz

1018.1 x 572.7 mm

Pixel Clock

Viewable Size

Input Signal

DVI DVI-D 24pin

DisplayPort DisplayPort Connector Digital RGB

VGA

RGB/HV*

HDMI

DVD/HD*

VIDEO1

VIDEO2*

S-VIDEO

2

2

2

15pin Mini D-sub

BNC (R,G,B,H,V)

HDMI Connector

BNC X 3

BNC

BNC

Mini DIN 4 pin

Digital RGB

Analog RGB

Sync

Analog RGB

Sync

Digital YUV

Digital RGB

Component

Composite

S-VIDEO

DVI (HDCP)

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920X1080 (60Hz), 1080p, 1080i

DisplayPort Complies with Standard V1.1a, applicable to HDCP V1.3

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920x1080 (60 Hz), 1080p, 1080i,

720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

HDMI

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920x1080 (60 Hz), 1080p, 1080i,

720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz

Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm

HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz

1.0 Vp-p/75 ohm

NTSC/PAL/SECAM/4.43NTSC/PAL60

Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)

NTSC/PAL/SECAM/4.43NTSC/PAL60

Output Signal

DVI

VIDEO1

DVI-D 24pin

BNC

Digital RGB

Composite

DVI (HDCP)

1.0 Vp-p with 75 ohm terminated

AUDIO

AUDIO

Input

RCA (L/R)

STEREO Mini Jack X2

HDMI Connector

Analog Audio

Digital Audio

DisplayPort Connector Digital Audio

Stereo L/R 0.5 Vrms

PCM 32, 44.1, 48 KHz (16/20/24bit)

PCM 32, 44.1, 48 KHz (16/20/24bit)

AUDIO

Output

Speaker Output

STEREO Mini Jack Analog Audio Stereo L/R 0.5 Vrms

Control

Power Supply

Operational Environment

Storage Environment

Dimension

Weight

VESA compatible mounting interface

Power Management

Plug & Play

Accessories

RS-232C In:

RS-232C Out:

LAN:

Remote IN:

Remote OUT:

External Speaker Jack 15 W + 15 W (8 ohm)

Internal Speaker 10W + 10W

9 Pin D-sub

9 Pin D-sub (with daisy chain)

RJ-45 10/100 BASE-T

Stereo Mini jack 3.5

Stereo Mini jack 3.5

1.4 - 3.1 A @ 100-240V AC, 50/60Hz

Temperature:

Humidity:

Altitude:

Temperature:

Humidity:

5 - 40°C / 41 - 104°F (Default brightness), 5 - 20°C / 41 - 68°F (Max brightness)

20 - 80% (without condensation)

0 - 3000 m (Brightness may decrease with altitude)

-20 - 60°C / -4 - 140°F

10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C

1121.5 (W) x 664.7 (H) x 107.0 (D) mm / 44.2 (W) x 26.2 (H) x 4.2 (D) inches

25.3 kg (55.8 lbs)

300 mm x 300 mm (M6, 4 Holes)

VESA DPM

VESA DDC2B, DDC/CI, DisplayPort

Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp x 2,

Screw x 2, CD-ROM, Thumbscrew for optional stand x 2

NOTE: Technical specifi cations are subject to change without notice. *1: Compressed image *2: Common terminal

English-39

Specifi cations - V651

Product Specifi cations

LCD Module

Frequency

Pixel Pitch:

Resolution:

Color:

Brightness:

Contrast Ratio:

Viewing Angle:

64.5”/1639 mm diagonal

0.744 mm

1920 x 1080

Over 16 million colors (depending on video card used)

500 cd/m 2 (Max.), 370 cd/m 2 (Factory setting Typ.) @25°C

5000:1

89° (typ) @ CR>10

Horizontal:

Vertical:

15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)

31.5 kHz - 91.1 kHz (Digital Input)

50.0 - 85.0 Hz

25.2 MHz - 162.0 MHz

1428.5 x 803.5 mm

Pixel Clock

Viewable Size

Input Signal

DVI DVI-D 24pin

DisplayPort DisplayPort Connector Digital RGB

VGA

RGB/HV*

HDMI

DVD/HD*

VIDEO1

VIDEO2* 2

2

2

15pin Mini D-sub

BNC (R,G,B,H,V)

HDMI Connector

BNC X 3

BNC

BNC

S-VIDEO Mini DIN 4 pin

Digital RGB

Analog RGB

Sync

Analog RGB

Sync

Digital YUV

Digital RGB

Component

Composite

S-VIDEO

DVI (HDCP)

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920X1080 (60Hz), 1080p, 1080i

DisplayPort Complies with Standard V1.1a, applicable to HDCP V1.3

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920x1080 (60 Hz), 1080p, 1080i,

720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

HDMI

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60* 1 , 1920x1080 (60 Hz), 1080p, 1080i,

720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz

Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm

HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz

1.0 Vp-p/75 ohm

NTSC/PAL/SECAM/4.43NTSC/PAL60

Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)

NTSC/PAL/SECAM/4.43NTSC/PAL60

Output Signal

DVI

VIDEO1

DVI-D 24pin

BNC

Digital RGB

Composite

DVI (HDCP)

1.0 Vp-p with 75 ohm terminated

AUDIO

AUDIO

Input

RCA (L/R)

STEREO Mini Jack X2

HDMI Connector

Analog Audio

Digital Audio

DisplayPort Connector Digital Audio

Stereo L/R 0.5 Vrms

PCM 32, 44.1, 48 KHz (16/20/24bit)

PCM 32, 44.1, 48 KHz (16/20/24bit)

AUDIO

Output

Speaker Output

STEREO Mini Jack Analog Audio Stereo L/R 0.5 Vrms

Control

Power Supply

Operational Environment

Storage Environment

Dimension

Weight

VESA compatible mounting interface

Power Management

Plug & Play

Accessories

RS-232C In:

RS-232C Out:

LAN:

Remote IN:

Remote OUT:

External Speaker Jack 15 W + 15 W (8 ohm)

Internal Speaker 10W + 10W

9 Pin D-sub

9 Pin D-sub (with daisy chain)

RJ-45 10/100 BASE-T

Stereo Mini jack 3.5

Stereo Mini jack 3.5

2.0 - 5.1 A @ 100-240V AC, 50/60Hz

Temperature:

Humidity:

Altitude:

Temperature:

Humidity:

5 - 40°C / 41 - 104°F (Default brightness), 5 - 20°C / 41 - 68°F (Max brightness)

20 - 80% (without condensation)

0 - 3000 m (Brightness may decrease with altitude)

-20 - 60°C / -4 - 140°F

10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C

1540.4 (W) x 909.2 (H) x 120.0 (D) mm / 60.6 (W) x 35.8 (H) x 4.7 (D) inches (with handle)

1540.4 (W) x 909.2 (H) x 118.9 (D) mm / 60.6 (W) x 35.8 (H) x 4.7 (D) inches (without handle)

54.0 kg (119.1 lbs)

400 mm x 400 mm (M8, 4 Holes)

VESA DPM

VESA DDC2B, DDC/CI, DisplayPort

Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, CD-ROM,

Eyebolt x 2

NOTE: Technical specifi cations are subject to change without notice. *1: Compressed image *2: Common terminal

English-40

Pin Assignment

1) RS-232C input/output

Pin No Name

1

2 connected to 7&8

RXD

6

7

8

3

4

5

9

TXD connected to 6

GND connected to 4 connected to 1&8 connected to 1&7

NC

1

6

This LCD monitor uses RXD, TXD and GND lines for RS-232C control.

D-SUB 9P

2) REMOTE IN

5

9

3) REMOTE OUT

English-41

Manufacturer’s Recycling and Energy Information

NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly products, and always strive to help defi ne and comply with the latest independent standards from agencies such as ISO

(International Organisation for Standardization) and TCO (Swedish Trades Union).

Disposing of your old NEC product

The aim of recycling is to gain an environmental benefi t by means of re-use, upgrading, reconditioning or reclamation of material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.

All required information concerning the disposal of the product and country-specifi c information on recycling facilities can be found on our following websites:

http://www.nec-display-solutions.com/greencompany/ (in Europe),

http://www.nec-display.com (in Japan) or

http://www.necdisplay.com (in USA).

Energy Saving

This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)

Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.

Mode

Normal Operation* 1

Power consumption

Approx. 155 W (V422)

Approx. 165 W (V462)

Approx. 330 W (V651)

Less than 1 W Energy Saving Mode* 1, * 2

Power Off Less than 0.5 W

*1: without any option, with factory settings.

*2: VGA input only.

LED colour

Green

Red, Green

Red

WEEE Mark (European Directive 2002/96/EC)

Within the European Union

EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your

NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased the product, or if applicable, follow any agreements made between yourself and NEC.

The mark on electrical and electronic products only applies to the current European Union Member States.

Outside the European Union

If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.

English-42

advertisement

Related manuals