installation guide
INSTALLATION GUIDE
Pot filler faucets
PF 3100
Ambient Series
PF 3200
Logik Series
PF 3300
Farm House Series
TECHNICAL DATA
Standard water flow 2.2 gpm - 60 PSI
Recommended pressure range 7.5-70 PSI
has certified that this faucet complies with NSF372 drinking water system components
requirements. These requirements meet California Health and Safety Code requirements for low
lead (AB1953) as well as the low lead requirements of the US Safe Drinking Water Act of 2014.
FAUCET INSTALLATION
1. Remove all contents from the package and check for completeness.
NOTE:
Contact us immediately if you see inconsistencies.
Phone: (1-800-626-5771)
Website: www.frankeksd.com
E-mail: ks-customerservice.us@franke.com
1
2
3
4
2/8
PACKAGE OF CONTENTS
FAUCET
BODY
ESCUTCHEON AND O’RING
TOOLS
2.
3.
4.
5.
6.
7.
8.
For best results, Franke recommends that this unit be installed by a licensed, professional
plumber-please read over the instructions before beginning the installation. Make sure to
observe all local plumbing and building codes during installation of this unit.
Remove faucet and hardware from its protective packaging. Disassemble the faucet from
the body by removing the set screw in the body and lifting the faucet from the body.
Shut off main water supply.
This faucet requires a 1/2” NPT male nipple at the desired faucet location for proper installation.
The nipple must have adequate bracing to support the faucet. ATTENTION: the faucet is
intended for use with cold water only! The water supply nipple should extend from the
finished wall between 3/8” and 1/2” (8,5 mm Min - 12,5mm Max).
Apply thread sealing tape or thread sealant onto the cold water supply fitting.
Slide the escutcheon onto the body and screw the body onto the water supply nipple. ATTENTION:
the o-ring should be sitting between the wall and the escutcheon. DO NOT use putty or
other sealant at this location.
Tighten body and confirm it is horinzontally level.
Installations tools
Allen wrench
(included)
Grease
(included)
Thread sealing
tape
Level
Screw driver
3/8
9. Fix the escutcheon by tightening the screw with the provided allen wrench.
10. Grease the o-rings with the special grease supplied.
11. Insert the faucet into the body. ATTENTION: insert the fixing screw into the white ring slot.
12. Tighten fixing screw with a flat screwdriver.
13. Remove the aerator by turning it counter clock wise with a 22mm wrench.
14. Turn on the faucet and allow it to run for several seconds. This will flush any debris
from the faucet from the installation process.While the faucet is on, check for leaks.
15. Turn off the faucet and reinstall the aerator in reverse order of step 13.
4/8
REPLACING THE CARTRIDGE
1.
2.
3.
4.
5.
5.
6.
7.
Shut off the water supply to the faucet.
Open the faucet briefly to relieve any pressure inside the faucet.
Move the faucet handle to the “OFF” position.
Remove the screw cover, unscrew the set screw and remove the handle.
For PF3300 Series, unscrew the cap.
Remove cartridge from valve body seat by using a 17mm socket wrench.
Install the new cartridge into valve body; ensure to tighten cartridge to 14 ft./lbs. (18.9 Nm).
Re-assemble faucet in reverse order.
Test for leakage.
PF 3100
PF 3200
PF 3300
GENERAL MAINTENANCE
Clean aerator periodically. Do not use harsh detergents, solvents, chemical agents, metallic sponges,
etc. that could harm the surface and damage the finish. Clean only with a soft sponge and soapy
water.
5/8
1
2
3
4
PARTS LIST PF 3100
HANDLE, ASSY
CARTRIDGE COLD
AERATOR
ESCUTCHEON FLANGE
PARTS NUMBER
PF 301 *
PF 302
PF 303
PF 304 *
* NOTE: Specify color finish when
ordering replacement parts
1
2
3
4
PARTS LIST PF 3200
HANDLE, ASSY CARTRIDGE COLD
AERATOR
ESCUTCHEON FLANGE
PARTS NUMBER
PF 304 *
PF 302
PF 303
PF 305 *
* NOTE: Specify color finish when
ordering replacement parts
6/8
1
2
3
4
PARTS LIST PF 3300
HANDLE, CAP, ASSY
CARTRIDGE COLD
AERATOR
ESCUTCHEON FLANGE
PARTS NUMBER
PF 306 *
PF 302
PF 303
PF 307 *
* NOTE: Specify color finish when
ordering replacement parts
7/8
8/8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising