② ① ② Belt Mount IMPORTANT SAFEGUARDS HOW

② ① ② Belt Mount IMPORTANT SAFEGUARDS HOW
㪍㪯㪈㪤㪮㪤㪦㪈㪊㩷㪩㪇㪄㪯㫏㫏
HOWTOUSE
1. Attach the holder to QBiC MS-1 (Sold separately).
Belt Mount
INSTRUCTION
MANUAL
ԘInsert the claws on the holder into the holes on the back of QBiC MS-1.
ԙThen tighten the screw (A) into the tripod thread of QBiC MS-1.
Please read this manual carefully before using
this product and keep it for future preference.
Ԙ
ԙ
IMPORTANTSAFEGUARDS
Please read all precautions and warnings before starting to use.
The information is provided to ensure proper operation of this product and will prevent
you or others from personal injury or loss of assets.
Review the following symbols so that you understand them before reading the rest of the
manual. Please read carefully and keep the manual in a safe place for future preference.
DANGER
Ignoring the warning and operating the system incorrectly subjects
the user to an extremely high risk of injury or death.
WARNING
CAUTION
࡮Firmly tighten the screw.
2. Attach the mount.
٨When using double-sided tape
Attach the mount using the supplied double-sided tape. Make sure to wipe off water, oil or dirt on the
attachment surface in advance
CAUTION
࡮Do not attach to the rough surface such as
wood, skin or cloth.
࡮There may be residue left on the surface when
you try to peel the tape away.
࡮Do not reuse the tape.
Ignoring the warning and operating the system incorrectly subjects
the user to possible risk of injury or death.
CAUTION
Ignoring the warning and operating the system incorrectly subjects
the user to risk of injury or loss of assets.
٨When using a commercially available screw
Using a “1/4-20UNC” screw (Length: 6mm or less) available in the market, you can attach to a
standard tripod and the like.
D A N G E R
CAUTION
࡮Make sure that the screw does not come
out of the mount.
Verify the following before you use this product or QBiC.
䊶There is no damage in the mounts. 䊶QBiC is firmly attached.
䊶The screws are firmly tightened.
䊶The mounts are firmly installed to the respective position.
When using this product or QBiC attaching to your body or helmet while
driving a car, motorbike or bicycle, pay attention to the traffic and road
surface conditions around you to prevent any accident.
Never operate this product or QBiC while driving a car, motorbike or
bicycle.
䊶It could cause injury when this product or QBiC accidentally hits your
body in a collision or a fall.
Do not attach this product or QBiC outside a car, motorbike or bicycle.
䊶It may be prohibited by law to attach an object other than specified
outside a car, motorbike or bicycle. If you have a permit and intend to
attach this product or QBiC outside a car, motorbike or bicycle, make
sure to attach them firmly so that they won’t come off during driving.
W A R N I N G
٨When using the belt mount (̪Use a commercially available belt.)
Fix the mount and the belt mount using the screw (B).
Width 㧦less than 30mm
Thickness㧦less than 2mm
CAUTION
࡮When installing to a place where there is a risk of
falling such as a ceiling and a wall surface, put a
wire through the security hole and tie it to a secure
place. (The wire is not included.)
Keep this product, package or packing materials out of baby㵭s reach.
䊶They could choke or injure a baby if swallowed. Contact a doctor
immediately if this happens.
Do not install this product in areas where salt erosion or corrosive gas is
produced.
䊶The product will be damaged and it may cause QBiC to drop accidentally,
leading to injury or malfunction.
3.Attach QBiC MS-1 to the mount.
Attach the QBiC MS-1 and the holder to the fixed mount.
Do not install this product to insecure places.
䊶It may cause QBiC to drop accidentally, leading to injury or malfunction.
Do not attach objects other than specified to the mounts.
䊶The object may drop due to insufficient support, leading to injury or
malfunction.
C A U T I O N
Do not clean this product with strong solvents such as thinner and benzene.
䊶This may damage the quality of rubber material.
Clean this product only with a dry, soft cloth. In case of heavy dirt, wash
lightly with fresh water. Then wipe it with a dry, soft cloth.
Do not use this product in hot place or under strong sunlight for a long
period of time.
䊶Excessive heat may damage the quality of this product or change its
shape, causing QBiC to drop due to insufficient support, leading to injury or
malfunction.
Do not move this product with excessive force when screws are tightened.
䊶It may cause the screw to become loose or damage the screw.
CAUTION
Be careful not to sandwich your fingers at the time of installation /
disassembly.
4.Remove QBiC MS-1 from the mount.
ԘPress down the lock.
ԙHolding the lock down, slide QBiC MS-1 and the holder backward to remove.
ԙ
Ԙ
Do not install this product to wet place or use under water.
䊶It may weaken the attachment of the double-faced tape causing the
product to easily detach itself.
Depending on the shape of the place, this product may not be installed.
䊶Do not force to install too much . It may damage the object.
Do not swing the object around.
䊶It may cause QBiC MS-1 and this product to be detached from the object.
WHAT’SINTHEBOX
‫غ‬Holder
‫غ‬Mount
‫غ‬Belt mount
‫غ‬Screw (2 types)
#
$
‫غ‬Double-sided tape
‫غ‬Belt
‫غ‬Instruction Manual
*Please refer to QBiC instruction manual for shooting information.
Installable device: QBiC MS-1
̪Do not attach objects other than specified to this products.
PLEASE NOTE:
Ŷ Contents of this manual may be subject to change without notice.
Please check the latest version from the following QBiC MS-1 website.
http://www.elmoqbic.com/
Ŷ We shall not be liable for any direct, indirect, punitive, incidental, special, consequential or
exemplary damages, including but not limited to loss of profits or claims by third party,
resulting from your use of this product.
ƔContact Us
Please refer to the above-mentioned QBiC Website.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising