getting started? easy.
User Manual
GETTING
STARTED?
EASY.
ZWD 81683 NW
EN User Manual
Washer Dryer
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
WARNING!
Risk of suffocation, injury or permanent disability.
•
•
•
•
•
•
•
This appliance can be used by children aged 8 years and
above and by persons with reduced capabilities provided that
they have been given instruction and/or supervision regarding
the safe use of the appliance and understand the potential
hazards involved.
Do not let children play with the appliance.
Children aged 3 years and under must be kept away from this
appliance when it is in operation at all times.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance door when it is
open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
•
•
2
Do not change the specification of this appliance.
The appliance shall be installed as a freestanding product or
below the kitchen worktop if space margins permit.
Do not install the appliance behind a lockable door, a sliding
door or a door with a hinge on the opposite side, that would
prevent the appliance door from being fully opened.
Connect the mains plug to the mains socket only at the end of
the installation process. Make sure that the mains plug is
accessible after installation.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The ventilation opening in the base (if applicable) must not be
covered by a carpet, mat, or any floor covering.
Ensure good air ventilation in the located room to avoid the
backflow of unwanted gases into the room from appliances
burning gas or other fuels, including open fires.
Exhaust air must not be discharged into a flue which is used for
exhausting fumes from any appliances burning gas or other
fuels.
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
Do not exceed the maximum load of 8 kg (refer to the
"Programme chart" chapter).
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Wipe away lint or packaging debris that has accumulated
around the appliance.
Items that have been soiled with substances such as vegetable
or mineral oil, acetone, alcohol, petrol, kerosene, spot removers,
turpentine, waxes and wax removers should be washed
separately with an extra amount of detergent before being dried
in the washer dryer.
Do not use the appliance if items have been soiled with
industrial chemicals.
Do not dry unwashed items in the wash dryer.
Items such as foam rubber (latex foam), shower caps,
waterproof textiles, and rubber backed articles and clothes, or
pillows fitted with foam rubber pads should not be dried in the
washer dryer.
Fabric softeners, or similar products, should only be used as
specified by the product manufacturer’s instructions.
3
•
•
•
•
•
•
Remove all objects from items that could be a source of fire
ignition such as lighters or matches.
Never stop the washer dryer before the end of the drying cycle
unless all items are quickly removed and separated so that
residual heat can dissipate.
The final part of the washer dryer cycle takes place without heat
(cool down cycle) to ensure that items reach a temperature that
will not cause damage to them.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
SAFETY INSTRUCTIONS
INSTALLATION
• Follow the installation instruction supplied with
the appliance.
• Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
• Always keep the appliance vertical when being
moved.
• Make sure that there is air circulation between
the appliance and the floor.
• Remove all the packaging and the transit bolts.
• The floor area where the appliance is to be
installed must be flat, stable, heat resistant and
clean.
• Keep the transit bolts in a safe place. If the
appliance is to be moved in future they must be
reattached to lock the drum to prevent internal
damage.
• Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
• Do not install or use a damaged appliance.
• Do not install the appliance where the appliance
door cannot be fully opened.
• Adjust the feet to have the necessary space
between the appliance and the flooring.
• When the appliance is in its permanent position,
check that it is fully level with the aid of a spirit
level. If it is not, adjust the feet accordingly.
4
ELECTRICAL CONNECTION
WARNING! Risk of fire and electrical
shock.
•
•
•
•
•
•
•
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and extension
cables.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Do not touch the mains cable or the mains plug
with wet hands.
UK and Ireland only. This appliance is fitted with
a 13 A mains plug. If it is necessary to change
the mains plug fuse, use only a 13 A ASTA (BS
1362) fuse.
This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
– If a detergent ball is used, remove it before
starting a drying programme.
– Do not use a detergent ball if setting a nonstop programme.
USE
WARNING! Risk of injury, electrical
shock, fire, burns or damage to the
appliance.
•
•
•
•
•
•
•
•
This appliance is for household use only.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Do not touch the glass door while a programme
is in operation. The glass can get hot.
Do not dry damaged (torn, frayed) items that
contain padding or fillings.
If laundry has been washed with a stain
remover, carry out an additional rinse cycle
before starting a drying cycle.
Make sure that all metal objects are removed
from the laundry.
Only dry fabrics that are suitable to dry in the
washer dryer. Follow the cleaning instruction on
the item label.
Plastic items are not heat resistant.
WARNING! Risk of injury or damage
to the appliance.
•
•
Do not sit or stand on the open door.
Do not dry dripping wet clothes in the
appliance.
DISPOSAL
• Disconnect the appliance from the mains
electrical and water supplies.
• Cut off the mains electrical cable close to the
appliance and dispose of it.
• Remove the door catch to prevent children or
pets from becoming trapped in the drum.
• Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
1 Worktop
2 Detergent dispenser
3
3 Control panel
4 Door handle
4
5 Rating plate
6 Drain pump filter
7 Feet for levelling the appliance
5
6
7
INSTALLATION ON SUSPENDED FLOORING
Suspended wooden floors are particularly
susceptible to vibration.
To limit vibration we recommend placing a
waterproof wooden panel, at least 15 mm thick,
under the appliance. It should be screwed to at
least 2 floor beams and should extend beyond the
front feet.
If possible, install the appliance where the floor is
more stable.
FIXING PLATE KIT (4055171146)
Available from your authorised dealer.
5
If you install the appliance on a plinth, secure the
appliance in the fixing plates.
Read carefully the instructions supplied with the
accessory.
CONTROL PANEL
CONTROL PANEL DESCRIPTION
1
2
3
4
5
6
Temperature
Drying
Time
Delay
Start
Drying
Level
Prewash
Spin
7
8
9
Start/Pause
11
1 On Off push button
2 Programme knob
(On/Off)
3 Spin reduction touch button
4 Temperature touch button
5 Display
(Spin)
(Temperature)
6 Drying time touch button
(Drying Time)
7 Delay start touch button
(Delay Start)
6
8 Prewash touch button
10
(Prewash)
9 Drying level touch button
(Drying Level)
10 Start/Pause touch button
(Start/Pause)
11 Time Manager touch button
(TimeAdjust)
DISPLAY
A
B
C
J
I
D
E
H
G
A. The Temperature area:
F
E.
: Temperature indicator
: Cold water indicator
B.
: Time Manager indicator.
C. The time area:
•
•
D.
: The permanent Extra rinse option.
F.
,
,
: The indicators of dryness level.
G. The spin area:
: the programme duration
: the delay start
•
: the Spin speed indicator
•
: the No spin indicator
•
H.
•
: the alarm codes
•
: the message of error
•
: the programme is completed.
I.
J.
: the Rinse hold indicator
: The washing phase.
: The child safety lock indicator.
: The door locked indicator
: The drying phase.
PROGRAMMES
PROGRAMME CHART
Programme
Temperature range
Maximum load
Maximum spin speed
Programme description
(Type of load and soil level)
Washing programmes
Cottons
90 °C - Cold
Economy1)
60 °C - 40 °C
8 kg
1600 rpm
White cotton and coloured cotton.
Normal soil and light soil.
8 kg
1600 rpm
White cotton and fast-coloured cotton. Normal soil. The energy consumption decreases and the time of the washing programme is extended.
7
Programme
Temperature range
Synthetics
60 °C - Cold
Wool/Handwash
40 °C - Cold
Delicates
40 °C - Cold
Mix 20°
20 °C
Super Eco
Cold
Maximum load
Maximum spin speed
4 kg
1200 rpm
Synthetic items or mixed fabric
items. Normal soil.
1.5 kg
1200 rpm
Machine washable wool, hand
washable wool and delicate fabrics
with «hand washing» care symbol.2)
4 kg
1200 rpm
Delicate fabrics such as acrylics,
viscose, polyester items. Normal soil.
3 kg
1200 rpm
Special programme for cotton, synthetic
and mixed fabrics lightly soiled. Select
this programme to reduce the energy
consumption. Make sure that the detergent is suitable for low temperatures in
order to have good washing results3).
3 kg
1200 rpm
Mixed fabric (cotton and synthetic
items)4).
8 kg
To drain the water in the drum. All fabrics.
8 kg
1600 rpm
To spin the laundry and to drain the water in the drum. All fabrics, except
woollens and delicate fabrics.
8 kg
1600 rpm
To rinse and spin the laundry. All fabrics, except woollens and very delicate
fabrics. Reduce the spin speed accordingly to the type of laundry.
1 kg
Drying programme for woollens.
3 kg
Drying programme for synthetic items.
6 kg
Drying programme for cotton items.
Drain
Spin5)
Rinse
Cold
Programme description
(Type of load and soil level)
Drying programmes
Wool Dry
Synthetics Dry
Cottons Dry
Washing programmes
8
Programme
Temperature range
Maximum load
Maximum spin speed
1.5 kg
800 rpm
Rapid
30°C
Programme description
(Type of load and soil level)
A short cycle for synthetic and delicate items with light soil level or for
items to freshen up.
1) Cottons energy saving programme. This programme at a 60ºC with a load of 8 kg is the reference programme for data entered in the energy label, in compliance with EEC 92/75 standards. Set this programme to have a good washing results and decrease the energy consumption. The time of the washing
programme is extended.
2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
3) The appliance performs the short heating phase if the water temperature is below 20°C. The appliance
can show the temperature setting as “cold”.
4) This programme is for daily use and has the lowest energy and water consumption whilst maintaining a
good washing performance.
5) The default phase of the spin speed is related to cotton items. Set the suitable spin speed.
Programme options compatibility
Programme
Cottons
■
■
■
■
■
■
Economy
■
■
■
■
■
■
Synthetics
■
■
■
■
■
■
Wool/Handwash
■
■
■
■
Delicates
■
■
■
■
■
■
Mix 20°
■
■
Super Eco
■
■
■
■
■
■
■
Drain
Spin
■
■
Rinse
■
■
Rapid
■
■
■
■
■
■
■
9
AUTOMATIC DRYING
Dryness Level
Extra Dry
For towelling materials
Cupboard Dry1)
For items to be stored
Iron Dry
Suitable for ironing
Type of fabric
Load
Cottons and Linen
(bathrobes, bath towels, etc)
up to 6 kg
Cottons and Linen
(bathrobes, bath towels, etc)
up to 6 kg
Synthetics and mixed fabrics
(jumpers, blouses, underwear,
household linen)
up to 3 kg
Silk items (blouses, shirts,
clothing..)
up to 1 kg
Wool items (woollen jumpers)
up to 1 kg
Cottons and Linen
(sheets, tablecloths, shirts, etc)
up to 6 kg
1) Hints for test institute The test performance, in accordance with EN 50229, must be carried out with
a FIRST drying load of the maximum declared drying capacity (load composition according to EN61121)
by setting the AUTOMATIC CUPBOARD DRY programme for Cotton. The SECOND drying load with the
residual load must be tested by setting the AUTOMATIC CUPBOARD DRY programme for Cotton.
TIMED DRYING
10
Dryness Level
Type of fabric
Extra Dry
For towelling materials
Cottons and Linen
(bathrobes, bath towels, etc)
Load (kg)
Spin
speed
(rpm)
Suggested
duration
(mins)
6
1600
220 - 240
4
1600
140 - 160
2
1600
100 - 110
6
1600
210 - 230
4
1600
130 - 150
Cupboard Dry
For items to be stored
Cottons and Linen
(bathrobes, bath towels, etc)
2
1600
90 - 100
Cupboard Dry
For items to be stored
Synthetics and mixed fabrics
(jumpers, blouses, underwear,
household linen)
3
1200
100 - 110
1
1200
40 - 50
Wool
(woollen jumpers)
1
1200
110 - 130
Silk
(blouses, shirts, clothes etc)
1
1000
80
Dryness Level
Iron Dry
Suitable for ironing
Type of fabric
Load (kg)
Cottons and Linen
(sheets, tablecloths, shirts, etc)
Spin
speed
(rpm)
Suggested
duration
(mins)
6
1600
150 - 170
4
1600
85 - 105
2
1600
55 - 65
CONSUMPTION VALUES
The data in this table are approximate. Different variables can affect the data: the quantity
and type of laundry, the water and ambient temperature.
At the start of the programme, the display shows the programme duration for the maximum load capacity.
During the washing phase the programme duration is automatically calculated and can be
greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton
60°C, maximum load capacity 8 kg, the programme duration exceeds 2 hours; actual load
1 kg, the programme duration will be less than 1 hour).
When the appliance is calculating the real programme duration a dot flashes in the display.
Programmes
Load (kg)
Energy conApproximate proWater consumption
gramme duration (misumption (litre)
(kWh)
nutes)
Cottons 60°C
8
1.60
72
168
Economy
Cotton Energy Saving Programme 60°C1)
8
1.03
57
220
Cottons 40°C
8
1.00
72
164
Synthetics 40°C
4
0.60
50
110
4
0.70
60
91
1.5
0.35
57
58
Delicates 40°C
Wool/Handwash 30°C
1) «Cotton Energy Saving programme » at 60°C with a load of 8 kg is the reference programme for the
data entered in the energy label, in compliance with EEC 92/75 standards.
OPTIONS
TEMPERATURE
Set this option to change the default temperature.
Indicator
= cold water.
The display shows the set temperature.
11
Additional spin options:
No Spin
• Set this option to remove all spin phases.
• Set it for very delicate fabrics.
• The rinse phase uses more water for some
washing programmes.
• The display shows the indicator
.
Rinse Hold
• Set this option to prevent the laundry creases.
• The washing programme stops with the water in
the drum. The drum turns regularly to prevent
the laundry creases.
• The door stays locked. You must drain the water
to unlock the door.
•
The display shows the indicator
.
To drain the water refer to ‘At the end
of the programme’.
DRYING TIME
With this option you can set the time for the fabrics
you have to dry. The display shows the set value.
Each time you press this touchpad the time value
increases by 5 minutes.
PREWASH
With this option you can add a prewash phase to a
washing programme.
Use this option for heavy soil.
When you set this option the programme duration
increases.
The related indicator comes on.
TIME ADJUST
When you set a washing programme, the display
shows the default duration.
Press
or
to decrease or increase the
programme duration.
The Time Manager is available only with the
programmes in the table.
Indicator
SPIN
With this option you can decrease the default spin
speed.
The display shows the indicator of the set speed.
1)
You cannot set all time values for
different types of fabrics.
DRYING LEVEL
With this option you can set an automatic level of
dryness for the laundry. The display shows the
symbol of the set level.
•
•
•
Extra dry level for cotton items
Cupboard dry level for cotton and synthetic
items
Iron dry level for cotton items
DELAY START
With this option you can delay the start of a
programme from 30 minutes to 20 hours.
The display shows the related indicator.
12
3)
■
■
■
■
■
■
■
■
■
■
■2)
■2)
■
■
■
■
■
■
■
■
■2)
2)
1) Shortest: to fresh the laundry.
2) Programme default duration.
3) Longest: Increasing the programme duration
gradually decreases the energy consumption. The
optimized heating phase saves energy and the longer duration maintains the same washing results
(specially for normal soil).
SETTINGS
CHILD LOCK
With this option you can prevent that the children
play with the control panel.
•
To activate/deactivate this option, press
and
at the same time until the indicator
comes on/goes off.
You can activate this option:
•
After you press
: the options and the
programme knob are locked.
•
Before you press
start.
: the appliance cannot
PERMANENT EXTRA RINSE
With this option you can permanently have an extra
rinse when you set a new programme.
•
To activate/deactivate this option press
and
at the same time until the indicator
comes on/goes off.
ACOUSTIC SIGNALS
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
press
and
at the same time for 6 seconds.
If you deactivate the acoustic signals,
they continue operate when the
appliance has a malfunction.
BEFORE FIRST USE
1. Put 2 litre of water in the detergent
compartment for washing phase.
This activates the drain system.
2. Put a small quantity of detergent in the
compartment for washing phase.
3. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
DAILY USE - WASHING ONLY
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to max. loads indicated in "Programme chart".
4. Close the door.
CAUTION!
Make sure
that no laundry stays between the
seal and the
door. There
is a risk of
water leakage or damage to the
laundry.
13
USING DETERGENT AND ADDITIVES
1. Measure out the detergent and the fabric
conditioner.
2. Put the detergent
and the fabric conditioner into the compartments.
3. Carefully close the
detergent drawer.
4. Position B for liquid detergent.
B
5. Close the detergent
dispenser.
DETERGENT COMPARTMENTS
Detergent compartment for prewash phase.
Detergent compartment for
washing phase.
Compartment for liquid additives
(fabric conditioner, starch).
When you use the liquid detergent:
• Do not use gelatinous or thick liquid detergents.
• Do not put more liquid then the
maximum level.
• Do not set the prewash phase.
• Do not set the delay start.
Flap for powder or liquid detergent.
LIQUID OR POWDER DETERGENT
1. Position A for powder
detergent (factory setting).
A
ACTIVATING THE APPLIANCE
Press the
button to activate or deactivate the
appliance. A tune sounds when the appliance is
activated.
2. Extract the detergent
dispenser.
1
2
SETTING A PROGRAMME
1. Turn the programme knob and set the
programme:
• The related programme indicator comes on.
•
•
3. Turn the flap downwards.
The indicator of the
flashes.
The display shows the level of the Time
Manager, the programme duration and the
indicators of the programme phases.
2. If necessary, change the temperature, the spin
speed, the cycle duration or add available
options. When you activate an option, the
indicator of the set option comes on.
If you set something incorrect, the
display shows the message
.
STARTING A PROGRAMME WITHOUT THE
DELAY START
Press
14
.
The indicator of
stays on.
•
starts to flash on the
The indicator
display.
The programme starts, the door locks, the
. To cancel the delay start:
display shows the indicator
•
•
stops to flash and
You can cancel or change the set of
the delay start before you press the
•
•
.
•
After approximately 15 minutes from
the start of the programme:
• The appliance adjusts automatically
the programme duration agree with
the laundry load.
• The display shows the new value.
STARTING A PROGRAMME WITH THE DELAY
START
1. Press
again and again until the display
shows the delay you want to set.
The related indicator comes on the display.
:
2. Press
• The appliance starts the countdown.
• The door locks, the display shows the
indicator
.
If the indicator
flashes, the door is
locking. If the display shows an alarm
•
message after the indicator
has
flashed for a few seconds, it indicates that
the door is not properly locked (for more
details see Troubleshooting chapter).
When the countdown is completed, the
programme starts automatically.
Press
shows
If the indicator
flashes, the
door is locking. If the display
shows an alarm message after
the indicator
has flashed
for a few seconds, it indicates
that the door is not properly
locked (for more details see
Troubleshooting chapter).
The drain pump can operate for a short time
when the appliance fills water.
Press
to set the appliance
to pause.
•
until the display
'.
Press
again to start the
programme immediately.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
.
1. Press
The indicator flashes.
2. Change the options.
3. Press
again.
The programme continues.
CANCELLING A RUNNING PROGRAMME
1. Press the button
for some seconds to
cancel the programme and to deactivate the
appliance.
2. Press the same button again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
OPENING THE DOOR
CAUTION! If the temperature and
level of the water in the drum are too
high and the drum still rotates, you
cannot open the door.
While a programme or the delay start operates, the
appliance door is locked and the display shows the
indicator
.
Open the appliance door when the
programme or the delay start operates:
1. Press
to pause the appliance.
2. Wait until the door lock indicator
3. Open the door.
4. Close the door and press again
goes off.
.
15
The programme or delay start continues to operate.
AT THE END OF THE PROGRAMME
• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
•
In the display
•
•
•
The indicator of the
goes off.
You can open the door.
Remove the laundry from the appliance. Make
sure that the drum is empty.
Close the water tap.
•
The appliance drains and spins
automatically after approximately 18
hours (except for Wool programme).
comes on.
•
Press the button
for some seconds to
deactivate the appliance.
• Keep the door ajar, to prevent the mildew and
odours.
The washing programme is completed, but
there is water in the drum:
• The drum turns regularly to prevent the creases
in the laundry.
is on. The door
The door lock indicator
stays locked.
• You must drain the water to open the door.
To drain the water:
•
1. Press
spins.
for some seconds to
3. Press the button
deactivate the appliance.
AUTO STAND-BY OPTION
The AUTO Stand-by function automatically
deactivates the appliance to decrease the energy
consumption when:
• You do not use the appliance for 5 minutes
before you press
•
Press the button
to activate the appliance
again.
The display shows the end of the last set
programme.
Turn the programme knob to set a new cycle.
If you set a programme or an option
that ends with water in the drum, the
AUTO Stand-by function doesn't
deactivate the appliance to remind
you to drain the water.
. The appliance drains the water and
2. To make the appliance drain only, set
necessary, decrease the spin speed.
.
Press the button
to activate the appliance
again.
After 5 minutes from the end of the washing
programme
. If
DAILY USE - DRYING ONLY
WARNING! Refer to Safety chapters.
DRYING SETTING
WARNING! Make sure that the
water tap is open.
1. Press On/Off for some seconds to activate the
appliance.
2. Load the laundry one item at a time.
3. Turn the programme dial to the programme
applicable for the items to dry. The display
shows the drying indicator
.
To have a good drying performance
do not exceed the maximum drying
loads recommended in the user
manual. Do not set a spin speed
lower than the automatic speed of the
set programme.
16
DRYING AT AUTOMATIC LEVELS
The laundry can be dried at pre-defined levels of
dryness:
1. Press
again and again until the display
shows one of the dryness level indicator:
•
: IRON DRY level indicator for cotton
items
•
: CUPBOARD DRY level indicator for
cotton and synthetic items
•
: EXTRA DRY level indicator for cotton
items
The display shows a time value, calculated on the
default load size. If the amount of your laundry is
more or less than the default size, the appliance
adjusts automatically the time value during the
cycle.
2. Press
to start the programme.
The display shows the door locked indicator
The drying indicator
starts to flash.
.
You cannot set all dryness levels for
any type of laundry.
TIMED DRYING
The laundry can also be dried with a manual timed
drying:
1. Press
again and again to set the time value
(see the «Programmes for timed drying» table).
• The display shows 10 minutes. Each time
you press this touchpad the time value
increases by 5 minutes.
• The display shows the set time value: for
•
.
example –
After some seconds the display shows a
new time value:
. The appliance
calculates also the duration of the anticrease and the cooling phases.
2. Press
to start the programme.
• The display shows regularly a new time
value.
•
•
END OF THE DRYING PROGRAMME
The appliance stops automatically.
• The acoustic signals operate (if they are active).
•
In the display
comes on.
•
•
The indicator
goes off.
The last minutes of the drying cycle the
appliance performs a cooling and anti-crease
phase. The door is still locked.
When the door locked
you can open the door.
goes off in the display,
1. Press the button
for some seconds to
deactivate the appliance.
After some minutes from the end of the programme,
the energy saving function automatically
deactivates the appliance.
2. Remove the laundry from the appliance.
Make sure that the drum is empty.
3. Keep the door ajar, to prevent mildew and
odours.
4. Close the water tap.
The drying indicator
starts to flash.
The display shows the door locked
indicator
.
If you set only 10 minutes of drying,
the appliance performs only a cooling
phase.
If the laundry is not sufficient dry, set
again a short drying time.
DAILY USE - WASHING & DRYING
WARNING! Refer to Safety chapters.
NON-STOP PROGRAMME
1. Press On/Off for some seconds to activate the
appliance.
2. Load the laundry one item at a time.
To have a good drying performance
do not exceed the maximum drying
loads recommended in the user
manual. Do not set a spin speed
lower than the automatic speed of the
set programme.
3. Put the detergent and the additives in the
appropriate compartment.
4. Turn the programme dial to the washing
programme.
The display shows the indicators of the different
washing phases.
5. Set the available options.
WASHING & AUTOMATIC DRYING
1. Press
again and again until the display
shows one of the dryness level indicator:
•
: IRON DRY level indicator for cotton
items
•
: CUPBOARD DRY level indicator for
cotton and synthetic items
•
: EXTRA DRY level indicator for cotton
items
The display shows the indicator
. The time value
on the display is the duration of the washing +
drying cycles, calculated on a default load size.
17
To have a good drying the appliance
does not let you set a too low spin
speed for the items to be washed and
dried.
2. Press
to start the programme.
In the display the indicator of the set dryness level
stays on.
The door locked indicator
goes on.
The display shows regularly a new time value.
The last minutes of the drying cycle
the appliance performs the anti-crease
and the cooling phases.
WASHING & TIMED DRYING
To have a good drying the appliance does not let
you set a too low spin speed for the items to be
washed and dried.
1. Press
to set the drying time value. The
display shows 10 minutes.
The indicator
comes on in the display. The
display shows the set drying value time. for
example:
. After some seconds the display
shows the final time value
, that is the total
duration of the washing and drying cycles (washing
+ drying + anti-crease + cooling phases).
If you set only 10 minutes of drying
after washing, the appliance calculates
also the duration of the anti-crease
and the cooling phases.
2. Press
to start the programme.
comes on. The door
In the display the indicator
is locked. The display shows regularly a new time
value.
For more information see "At the end of the drying
programme " of the previous chapter.
1. Remove the laundry from the appliance.
Make sure that the drum is empty.
2. Keep the door ajar to prevent mildew and
odours.
3. Close the water tap.
FLUFF IN THE FABRICS
During the washing and/or drying phase, some
types of fabric, (sponge, wool, sweatshirt) could
release fluff.
The released fluff could stick to the fabrics during
the next cycle.
To prevent the fluff in your laundry, we recommend
that you:
• Do not wash dark fabrics after you have washed
and dried light coloured fabrics (new sponge,
wool, sweatshirt ) and the contrary.
• Line dry this type of fabrics at open air when
they are washed the first time.
• Clean the drain filter.
• After the drying phase, clean the empty drum,
the gasket and the door with a wet cloth.
HOW TO REMOVE THE FLUFF IN THE
GARMENTS
To remove the fluff inside the drum, set a special
programme:
1. Empty the drum.
2. Clean the drum, the gasket and the door with a
wet cloth.
3. Set the rinse programme.
4. Press at the same time
and
to activate
the cleaning function until the display shows
CLE.
5. Press
to start the programme.
END OF THE PROGRAMME
The appliance stops automatically. The acoustic
signals operate (if they are active).
HINTS AND TIPS
WARNING! Refer to Safety chapters.
THE LAUNDRY LOAD
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on the
laundry care labels.
18
•
•
•
•
•
Do not wash white and coloured items together.
Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
Empty the pockets and unfold the items.
Turn multilayered fabrics, wool and items with
painted illustrations inside out.
•
•
•
•
•
Remove hard stains.
Wash heavy soil stains with a special detergent.
Be careful with the curtains. Remove the hooks
or put the curtains in a washing bag or
pillowcase.
Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, etc. ).
A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially
made for washing machines:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (40
°C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
• Do not mix different types of detergents.
• To help the environment, do not use more than
the correct quantity of detergent.
• Obey the instructions that you find on the on
packaging of these products.
• Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
• If your appliance does not have the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
ECOLOGICAL HINTS
• Always start a washing programme with the
maximum load of laundry allowed.
• If necessary, use a stain remover when you set a
programme with a low temperature.
• To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
DRYING HINTS
Prepare the drying cycle
•
•
•
Open the water tap.
Check if the drain hose is connected properly.
Refer to installation chapter for more
information.
For the maximum laundry load of the drying
programmes, refer to the drying programmes
table.
ITEMS NOT SUITABLE FOR DRYING
Do not set a drying programme for this
laundry:
• Very delicate items.
• Synthetic curtains.
• Pieces of clothing with metal inserts.
• Nylon stockings.
• Quilts.
• Bed covers.
• Duvets.
• Anoraks.
• Sleeping bags.
• Fabrics with residue of hair sprays, nail solvents
or similar.
• Garments with foam-rubber or materials similar
to foam-rubber.
GARMENT LABELS
When you dry the laundry, obey the indications on
the labels of the manufacturers:
•
= The item can be tumble dried
•
= The drying cycle is at high temperature
•
•
= The drying cycle is at reduced
temperature
= The item can not be tumble dried.
DRYING CYCLE DURATION
The drying time can change depending on:
• speed of the last spin
• dryness level
• type of laundry
• weight of the load
19
ADDITIONAL DRYING
If, at the end of the drying programme, the laundry
is still damp, set a short drying cycle again.
WARNING! To avoid creasing and
shrinkage do not overdry the
laundry.
GENERAL TIPS
Refer to the «Drying programmes» table to find the
average drying times.
Experience will help you to dry the laundry better.
Take note of the duration of the cycles done before.
To avoid the static charge at the end of the drying
cycle:
1. Use fabric conditioner in the washing cycle.
2. Use special fabric conditioner for tumble
dryers.
When the drying programme is completed remove
the laundry promptly.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance with soap and warm water
only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Perform a
maintenance wash regularly. To do this:
• Remove all laundry from the drum.
• Select the cotton programme with the highest
temperature with a small quantity of detergent.
DOOR SEAL
Regularly examine the
seal and remove all objects from the inner part.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machines. Do this separately from the
laundry wash.
Always obey the instructions that you
find on the packaging of the product.
CLEANING THE DETERGENT DISPENSER
1
2
1
2
20
3
4
CLEANING THE DRAIN FILTER
WARNING! Do not clean the drain
filter if the water in the appliance is
hot.
1
2
3
1
4
1
2
5
2
1
6
7
8
1
2
1
2
9
CLEANING THE INLET HOSE AND THE VALVE FILTER
1
1
2
3
4
2
45°
3
20°
EMERGENCY DRAIN
Because of a malfunction, the appliance cannot
drain the water.
If this occurs, do steps (1) through (9) of 'Cleaning
the drain filter'. If necessary, clean the pump.
When you drain the water with the emergency drain
procedure, you must activate the drain system
again:
1. Put 2 litres of water in the main wash
compartment of the detergent dispenser.
2. Start the programme to drain the water.
21
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0° C, remove the
remaining water from the inlet hose and the drain
pump.
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in a
container and let the water flow out of the
hose.
4. Empty the drain pump. Refer to the emergency
drain procedure.
5. When the drain pump is empty, install the inlet
hose again.
WARNING! Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during
operation.
First try to find a solution to the problem (refer to
the table). If the problem persists, contact the
Authorised Service Centre.
With some problems, the acoustic signals
operate and the display shows an alarm
code:
•
•
•
- The appliance does not fill with water
properly.
- The appliance does not drain the water.
- The appliance door is open or not
closed correctly. Please check the door!
If the appliance is overloaded,
remove some items from the drum
and/or keep pressed the door and
push the Start/Pause button at the
•
- The mains supply is unstable. Wait until
the mains supply is stable.
•
- No communication between electronic
elements of the appliance. Switch off and
switch on again.
WARNING! Deactivate the appliance
before you do the checks.
same time until the indicator
stops flashing (see the picture
below).
POSSIBLE FAILURES
Problem
The programme does not
start.
Possible solution
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
22
Problem
Possible solution
Make sure that there is not a damaged fuse in the fuse box.
Make sure that the Start/Pause has been pressed.
If the delay start is set, cancel the setting or wait for the end of countdown.
Deactivate the Child Lock function if it is on.
The appliance does not fill
with water properly.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For this
information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter of the inlet hose and the filter of the valve are
not clogged. Refer to “Care and cleaning”.
Make sure that the inlet hose has no kinks or bends.
Make sure that the connection of the water inlet hose is correct.
The appliance does not fill
with water and drain immediately.
Make sure that the drain hose is in the correct position. The hose may
be too low.
The appliance does not
drain the water.
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'.
Make sure that the connection of the drain hose is correct.
Set the drain programme if you set a programme without drain phase.
Set the drain programme if you set an option which ends with water in
the tub.
The spin phase does not
operate or the washing cycle lasts longer than usually.
Set the spin programme.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'.
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
There is water on the floor.
Make sure that the couplings of the water hoses are tight and there is
not water leakages.
Make sure that the drain hose have no damages.
Make sure you use the correct detergent and the correct quantity of it.
23
Problem
You cannot open the appliance door.
Possible solution
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
Make sure that the appliance receives electrical power.
This problem may be caused by a failure of the appliance. Contact the
Authorised Service Centre. If you need to open the door, please read
carefully «Emergency door opening».
The appliance makes an
unusual noise.
Make sure the levelling of the appliance is correct. Refer to 'Installation'.
Make sure that the packaging and/or the transit bolts are removed. Refer to 'Installation'.
Add more laundry in the drum. The load may be too small.
The cycle is shorter than
the time displayed.
The appliance calculates a new time according to the laundry load.
See the ‘Consumption Values’ chapter.
The cycle is longer than
the time displayed.
An unbalanced laundry load increases the duration time. This is a normal behaviour of the appliance.
The washing results are
not satisfactory.
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you wash
the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
You cannot set an option.
Make sure that you press only the wanted button(s).
The appliance does not dry
or does not dry correctly.
Turn the water tap on.
Make sure the drain filter is not clogged.
Reduce the laundry load.
Make sure you have set the correct cycle. if necessary ,set again a
short drying time.
The laundry is full of different colours fluff.
The fabrics washed in the previous cycle released fluff of a different
colour:
• The drying phase helps to eliminate some fluff.
• Clean the clothes with a fluff remover.
In case of an excessive amount of fluff in the drum run the special programme to clean it (refer to “Fluff in the fabrics" for more details).
After the check, activate the appliance. The programme continues from the point of interruption.
If the problem occurs again, contact the Authorised Service Centre.
If the display shows other alarm codes. Deactivate and activate the appliance. If the problem continues,
contact the Authorised Service Centre.
24
EMERGENCY DOOR OPENING
In case of power failure or appliance failure the
appliance door remains locked. The washing
programme continues, when the power is restored.
If the door remains locked in case of failure, it is
possible to open it using the emergency unlock
feature.
Before opening the door:
CAUTION! Make sure that the
water temperature and the
laundry are not hot. Wait till they
cool down, if necessary.
To open the door, proceed as follows:
1. Turn the selector to On/Off position to switch
the appliance off.
2. Disconnect the mains plug from the mains
socket.
3. Open the filter flap.
4. Keep the emergency unlock trigger pulled
downward and, at the same time, open the
appliance door.
CAUTION! Make sure that the
drum is not rotating. Wait till the
drum stops rotating, if necessary.
Make sure that the water level
inside the drum is not too high.
Proceed with an emergency drain,
if necessary (refer to «Emergency
drain» in «Care and cleaning»
chapter).
5. Take out the laundry and then close the
appliance door.
6. Close the filter flap.
TECHNICAL DATA
Dimension
Width/ Height/ Depth/ Total depth
600 mm/ 850 mm/ 605 mm/ 639 mm
Electrical connection
Voltage
Overall power
Fuse
Frequency
230-240 V
2200 W
13 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure
1)
Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Maximum wash load
Cotton
8 kg
Maximum dry load
Cotton
Synthetics
6 kg
3 kg
Spin Speed
Maximum
1600 rpm
1) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your domestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the
appliance inlet hose and the bottom of the water storage tank.
25
ENVIRONMENTAL CONCERNS
the symbol with the household waste. Return the
product to your local recycling facility or contact
your municipal office.
Recycle the materials with the symbol
. Put the
packaging in applicable containers to recycle it.
Help protect the environment and human health
and to recycle waste of electrical and electronic
appliances. Do not dispose appliances marked with
26
*
27
132953300-A-012016
WWW.ZANUSSI.COM/SHOP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising