Manual - Highlite
MANUAL
ENGLISH
Phantom 300 LED Matrix
V1
Ordercode: 40060
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Phantom 300 LED Matrix
Table of contents
Warning ...............................................................................................................................................................................3
Safety Instructions ......................................................................................................................................................... 3
Operating Determinations .......................................................................................................................................... 5
Rigging ............................................................................................................................................................................ 5
Connection with the mains......................................................................................................................................... 6
Return Procedure .......................................................................................................................................................... 7
Claims .............................................................................................................................................................................. 7
Description of the device.................................................................................................................................................8
Frontside.......................................................................................................................................................................... 8
Backside ......................................................................................................................................................................... 9
Installation ...........................................................................................................................................................................9
Set Up and Operation .......................................................................................................................................................9
Control Modes .............................................................................................................................................................10
One Phantom (Built-in Programs and Manual)..................................................................................................10
One Phantom (Sound-controlled)........................................................................................................................10
Multiple Phantoms (Master/Slave Control) .........................................................................................................10
Multiple Phantoms (DMX Control) ........................................................................................................................11
Multiple Phantoms (ArtNet Control) .....................................................................................................................12
Connecting to a Network ..............................................................................................................................................13
ArtNet settings .............................................................................................................................................................13
How to make a data cable......................................................................................................................................14
Software for controlling .............................................................................................................................................14
Fixture Linking ...............................................................................................................................................................15
Data Cabling ...............................................................................................................................................................15
Control Panel ...............................................................................................................................................................16
DMX Control Mode.....................................................................................................................................................16
DMX Addressing ..........................................................................................................................................................16
Menu Overview ...........................................................................................................................................................17
Main Menu Options ....................................................................................................................................................18
1. DMX-512 ................................................................................................................................................................18
2. ArtNet Settings ......................................................................................................................................................19
2.1. IP Address ...........................................................................................................................................................19
2.2. Subnet Mask ......................................................................................................................................................20
2.3. Net .......................................................................................................................................................................20
2.4. Sub-Net ...............................................................................................................................................................20
2.5. Universe ..............................................................................................................................................................21
3. Channel Mode .....................................................................................................................................................21
4. Run Mode ..............................................................................................................................................................21
4.1. DMX Mode .........................................................................................................................................................22
4.2. ArtNet ..................................................................................................................................................................22
4.3. Master Mode .....................................................................................................................................................22
4.4. Slave Mode........................................................................................................................................................22
4.5. Sound Mode ......................................................................................................................................................22
4.6. Manual Mode ...................................................................................................................................................22
5. Functions ...............................................................................................................................................................23
5.1 Pan Invert ............................................................................................................................................................23
5.2 Tilt Invert ...............................................................................................................................................................23
5.3. Dimmer Curve ...................................................................................................................................................24
5.4. DMX Fail ..............................................................................................................................................................24
5.5. Display ................................................................................................................................................................24
5.6. Back Light ...........................................................................................................................................................25
5.7. Reset ...................................................................................................................................................................25
5.8. Factory Sets .......................................................................................................................................................25
Ordercode: 40060
1
Phantom 300 LED Matrix
5.9. Auto Test .............................................................................................................................................................25
6. Version ...................................................................................................................................................................25
DMX Channels .............................................................................................................................................................26
12 Channels ..............................................................................................................................................................26
20 Channels ..............................................................................................................................................................28
120 Channels ............................................................................................................................................................31
Maintenance ....................................................................................................................................................................35
Replacing the Fuse .....................................................................................................................................................35
Troubleshooting ...............................................................................................................................................................35
No Light .........................................................................................................................................................................35
No Response to DMX..................................................................................................................................................36
Product Specifications ....................................................................................................................................................37
Dimensions ........................................................................................................................................................................38
Ordercode: 40060
2
Phantom 300 LED Matrix
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
•
•
•
•
Showtec Phantom 300 LED Matrix
2 mounting brackets with 4 quick-locks
Pro Power connector to Schuko cable (1,5 m)
User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
•
be qualified
•
follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
Ordercode: 40060
3
Phantom 300 LED Matrix
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoors, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
If the lens is obviously damaged, it has to be replaced, so that its functions are not impaired due to
cracks or deep scratches.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of the reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Phantom 300 LED Matrix. The
manufacturer will not accept liability for damages caused by the misuse or incorrect installation of
this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Repairs, servicing and electric connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.
Ordercode: 40060
4
Phantom 300 LED Matrix
Operating Determinations
•
•
•
•
•
•
This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
The minimum distance between light output and the illuminated surface must be more than 1 meter.
The maximum ambient temperature ta = 40°C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
•
•
•
•
•
If the Phantom 300 LED Matrix is lowered from the ceiling or high joists, professional trussing systems
have to be used.
Use a clamp to mount the Phantom 300 LED Matrix, with the mounting bracket, to the trussing
system.
The Phantom 300 LED Matrix must never be fixed swinging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
When rigging, derigging or servicing the projector, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.
Ordercode: 40060
5
Phantom 300 LED Matrix
The Phantom 300 LED Matrix can be placed on a flat stage floor or be mounted to any kind of truss by
means of a mounting bracket with quick-locks.
Improper installation can cause serious damage to people and property!
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
L
N
EU Cable
BROWN
BLUE
YELLOW/GREEN
UK Cable
RED
BLACK
GREEN
US Cable
YELLOW/COPPER
SILVER
GREEN
Pin
PHASE
NEUTRAL
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Ordercode: 40060
6
Phantom 300 LED Matrix
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
Ordercode: 40060
7
Phantom 300 LED Matrix
Description of the device
Features
The Showtec Phantom 300 LED Matrix is a moving head with high output and great effects.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Input voltage: 100-240V AC, 60/50Hz
Power consumption: 340W
Light source: 25 x 10W RGBW 4-in-1 LEDs
Light output: 44950 lux @ 2 m
DMX modes: 12, 20, 120 channels
Beam angle: 15º
Onboard: LCD display for easy setup
Control mode: Auto, Manual, Sound-controlled, Master/Slave, DMX-512, ArtNet
Continuous Pan/Tilt & Pan/Tilt inversion
Dimmer: 0-100%
Strobe: 0-20Hz
Dimming curves: Linear, Square, I-Square, S-curve
RGBW color mixing
Pan: 0º -- 540º, Tilt: 0º -- 270º
Pan/Tilt resolution: 16 bit
Connections: Pro Power connector IN/OUT & 3-pin DMX IN/OUT
Housing: flame-retardant plastic, die-cast aluminum
Fuse: T5L/250V
Dimensions: 230 x 395 x 480 mm (LxWxH)
Weight: 13 kg
Frontside
01)
02)
03)
04)
Fig. 01
25 x 10W RGBW 4-in-1 LEDs
Pan lock
LCD display
MENU control
Ordercode: 40060
8
Phantom 300 LED Matrix
Backside
05)
06)
07)
08)
09)
10)
11)
12)
13)
Fig. 02
Cooling fans
Pro power connector 100-240V IN
Pro power connector 100-240V OUT
Power switch ON/OFF
Fuse T5L/250V
RJ45 Ethernet connector OUT
3-pin DMX signal connector OUT
3-pin DMX signal connector IN
RJ45 Ethernet connector IN
Installation
Remove all packing materials from the Phantom 300 LED Matrix. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Ordercode: 40060
9
Phantom 300 LED Matrix
Control Modes
There are 5 modes:
•
•
•
•
•
Built-in programs (Master mode)
Manual
Sound-controlled
Master/Slave mode
DMX-512, ArtNet (12CH, 20CH, 120CH)
One Phantom (Built-in Programs and Manual)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Phantom is not connected with a DMX cable, it functions as a stand-alone device. Please
see page 22 for more information.
One Phantom (Sound-controlled)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) Turn on the music. If the device is set to sound-control, then the Phantom will react to the beat of
the music. Please see page 22 for more information about the sound-control options.
Multiple Phantoms (Master/Slave Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Phantoms.
The pins:
01) Earth
02) Signal (-)
03) Signal (+)
05) Link the units as shown in (Fig.03). Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. You can
use the same functions on the master device as described on page 22. This means that you can set
your desired operation mode on the master device and all slave devices will react the same as the
master device.
Multiple Phantoms (Master/Slave Set Up)
Fig. 03
Ordercode: 40060
10
Phantom 300 LED Matrix
Multiple Phantoms (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Phantoms and other devices.
05) Link the units as shown in (Fig.04), Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
06) Supply electric power: Plug electric mains power cords into each unit's Pro power socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Phantoms (DMX Set Up)
Fig. 04
Ordercode: 40060
11
Phantom 300 LED Matrix
Multiple Phantoms (ArtNet Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a CAT-5/CAT-6 cable to connect the Phantom’s "in" socket to your software/light controller’s
output.
04) Use a CAT-5/CAT-6 cable to connect the Phantom and other ArtNet devices.
04) Link the units as shown in fig. 05. Connect the first Phantom's RJ45 "out" socket with the second unit's
"in" socket, using a CAT-5/CAT-6 signal cable. Repeat this process to link the second, third, and
fourth units.
05) Supply electric power: Plug electric mains power cords into each unit's Pro power socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Phantoms ArtNet Set Up
Note : Link all cables before connecting electric power
Ordercode: 40060
12
Fig. 05
Phantom 300 LED Matrix
Connecting to a Network
ArtNet settings
01) Install any ArtNet-based software on your PC (Windows or Mac) or use a light controller which
supports ArtNet.
02) Connect the power supply to the Phantom 300 LED Matrix..
03) Connect the device’s Ethernet connector (13) to your software/light controller’s Ethernet connector,
using a CAT-5/CAT-6 cable.
04) Set the IP address of your software/light controller to 2.x.x.x or 10.x.x.x, depending on the ArtNet
settings.
05) Set the subnet mask to 255.0.0.0. on both – the Phantom and your software/light controller. Make
sure that all the fixtures in the network have a unique IP address.
06) If you want to connect more fixturex, follow the example below.
Example: The Phantom 300 LED Matrix, 120-channel mode.
01) Make sure that each connected Phantom has a unique IP address.
02) Make sure that the subnet mask on each device is set to 255.0.0.0.
03) Set the universe of the first Phantom to 1.
04) Set the first Phantom’s DMX address to 001.
05) Connect your Phantoms, inserting ascending universe numbers. Each universe has a maximum of 15
subnets.
06) Once you have reached the final subnet of the first universe, set the universe of the next Phantom to
2 and its DMX address to 001.
07) Repeat steps 5 and 6 up to 15 times, each time inserting ascending universe numbers (as there are
15 universes available).
08) If you have reached the final universe of your current net, and you still want to connect more
devices, set the net value of the following Phantom to 2 and repeat steps 4-7 .
09) Now, you are able to connect more Phantoms, as each separate net is equipped with 15 universes,
15 subnets each. There are 127 nets in total (the number of nets depends on the software which you
use).
10) Using your software (for example 50224 - Arkaos Media Master Express), map all the connected
devices, using the settings described above.
11) The Phantoms are now ready for use.
12) When creating large setups, it is recommended to use a 16-bit, high speed ethernet switch to
distribute the ArtNet data signal.
Ordercode: 40060
13
Phantom 300 LED Matrix
How to make a data cable
A Standard ETHERNET cable can be used to replace the data cable required to transmit the data for the
Phantom 300 LED Matrix.
Please follow the instructions below in order to create an extra Net Cable.
Take a standard net cable (CAT-5/ 5E /6) and connect it to the RJ45 connector, as shown in the picture
below (fig. 06). The wires should now be colored as follows:
Fig. 06
Software for controlling
In combination with Arkaos or DMT Software, you are able to play videos over the Phantom 300 LED
Matrix (pixelmapping). You only have to connect all the Phantoms and run your software.
50224
Arkaos Media Master Express
The latest update of the successful media server software.
502267
Arkaos Media Master Pro 4.0: PRO DMX video software for
lighting designers.
Ordercode: 40060
14
Phantom 300 LED Matrix
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
•
DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin.
Ordercode FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
•
DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
•
DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
•
DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
•
DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
DAP Audio PC Interface Cables
•
CAT-5 cable 7,6 mm Matte blue PVC. Ordercode FL55150 (1,5 m), FL553 (3 m), FL556 (6 m),
FL5510 (10 m), FL5515 (15 m), FL5520 (20 m).
•
CAT-6 cable (recommended for best data transfer). Ordercode FL563 (3 m), FL566 (6 m),
FL5610 (10 m), FL5615 (15 m), FL5640 (40 m).
Ordercode: 40060
15
Phantom 300 LED Matrix
Control Panel
Press and turn the control to navigate through
the menu options
Fig. 07
DMX Control Mode
The fixtures are individually addressed on a data-link and connected to the controller. When a DMX
signal is present, the DMX LED will blink.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the Phantom 300 LED Matrix will respond to the controller.
Please note when you use the controller, the unit has 120 channels.
When using multiple Phantoms, make sure that you set the DMX addresses right.
Therefore, the DMX address of the first Phantom should be 1(001); the DMX address of the second
Phantom should be 1+120=121 (121); the DMX address of the third Phantom should be 121+120=241
(241), etc. Please, make sure that you do not have any overlapping channels in order to control each
Phantom correctly. If two or more Phantoms are addressed similarly, they will work similarly.
Controlling:
After having addressed all Phantom fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Phantom 300 LED Matrix will automatically detect whether DMX 512 data is
received or not. If there is no data received at the DMX input, the DMX LED will not blink.
The problem may be:
•
The XLR cable from the controller is not connected with the input of the Phantom 300 LED Matrix.
•
The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 35 seconds
When the MENU control is neither pressed nor turned for 35 seconds, the display will show the default
screen. To return to the main menu, you have to press or turn the MENU control (04).
Once you have pressed or turned the control, the display will show the main menu screen.
Ordercode: 40060
16
Phantom 300 LED Matrix
Menu Overview
Ordercode: 40060
17
Phantom 300 LED Matrix
Main Menu Options
There are 6 menu modes:
•
•
•
•
•
•
1. DMX-512
2. ArtNet Settings
3. Channel Mode
4. Run Mode
5. Functions
6. Version
1. DMX-512
With this menu you can adjust the device’s DMX settings.
01) While in the main menu, turn the MENU control (04) until the display shows:
02) Press the MENU control (04) to enter the menu.
03) The display will show:
04) Turn the MENU control (04) to set the desired DMX address.
05) The adjustment range is between 001-512.
06) Press the MENU control (04) to confirm the DMX address.
Ordercode: 40060
18
Phantom 300 LED Matrix
2. ArtNet Settings
With this menu you can adjust the device’s ArtNet settings.
01) While in the main menu, turn the MENU control (04) until the display shows:
02) Press the MENU control (04) to enter the menu.
03) Turn the MENU control (04) to toggle through the following submenus:
04) Press the MENU control (04) to choose the desired submenu.
05) Turn the MENU control (04) to select Exit and press the MENU control (04) to return to the previous
menu.
2.1. IP Address
01)
02)
03)
04)
05)
Turn the MENU control (04) to select the section of the IP address which you want to edit.
Press the MENU control (04) to enter edition mode.
Turn the MENU control (04) to adjust the value.
Press the MENU control (04) to confirm.
Turn the MENU control (04) to select Exit and press the MENU control (04) to return to the previous
menu.
Ordercode: 40060
19
Phantom 300 LED Matrix
2.2. Subnet Mask
01)
02)
03)
04)
05)
Turn the MENU control (04) to select the section of the subnet mask which you want to edit.
Press the MENU control (04) to enter edition mode.
Turn the MENU control (04) to adjust the value.
Press the MENU control (04) to confirm.
Turn the MENU control (04) to select Exit and press the MENU control (04) to return to the previous
menu.
2.3. Net
01) Turn the MENU control (04) to set the desired net number. The adjustment range is between 000-127.
02) Press the MENU control (04) to confirm your choice.
2.4. Sub-Net
01) Turn the MENU control (04) to set the desired sub-net number. The adjustment range is between 000015.
02) Press the MENU control (04) to confirm your choice.
Ordercode: 40060
20
Phantom 300 LED Matrix
2.5. Universe
01) Turn the MENU control (04) to set the desired universe number. The adjustment range is between 000015.
02) Press the MENU control (04) to confirm your choice.
3. Channel Mode
01) While in main menu, turn the MENU control (04) until the display shows:
02) Press the MENU control (04) to enter the menu.
03) Turn the MENU control (04) to toggle between the 3 available channel modes:
•
12 channels
•
20 channels
•
120 channels
04) Press the MENU control (04) to choose the desired channel mode.
05) For more information about the DMX channels and their functions, see page 26.
4. Run Mode
01) While in main menu, turn the MENU control (04) until the display shows:
02) Press the MENU control (04) to enter the menu.
03) Turn the MENU control (04) to toggle between the 6 available modes:
•
DMX
•
ArtNet
•
Master
•
Slave
•
Sound
•
Manual
04) Press the MENU control (04) to open the desired mode.
Ordercode: 40060
21
Phantom 300 LED Matrix
4.1. DMX Mode
01) Press the MENU control (04) to activate DMX mode.
4.2. ArtNet
01) Press the MENU control (04) to activate ArtNet mode.
4.3. Master Mode
01) Turn the MENU control (04) to choose one of 8 built-in auto shows:
•
Showmode 01 – Showmode 08
02) Press the MENU control (04) to confirm your choice.
03) The device will now run the desired auto show.
4.4. Slave Mode
01) Turn the MENU control (04) to toggle between the 2 slave functions:
•
Slave1 (normal slave mode)
•
Slave2 (mirror slave mode)
03) Press the MENU control (04) to confirm your preferred slave mode.
04) The device is now operating in slave mode and it will react the same as the master device (Slave1),
or it will mirror the actions of the master device (Slave2).
4.5. Sound Mode
01) Press the MENU control (04) to enter the menu.
02) The display will show the following screen:
03) Turn the MENU control (04) to adjust the sound sensitivity. The adjustment range is between 000-255,
from low to high sensitivity.
04) Press the MENU control (04) to confirm.
4.6. Manual Mode
01) Turn the MENU control (04) to toggle between the 7 available functions:
•
Pan (Pan adjustment)
•
Tilt (Tilt adjustment)
•
Red (Red LED intensity)
•
Green (Green LED intensity)
•
Blue (Blue LED intensity)
•
White (White LED intensity)
•
Strobe (Strobe frequency)
02) Press the MENU control (04) to select the desired function. The adjustment range of each function is
between 000-255.
03) Turn the MENU control (04) to set the value.
04) Press the MENU control (04) to save changes.
05) Turn the MENU control (04) to choose Exit and press the MENU control (04) to return to the previous
menu.
Ordercode: 40060
22
Phantom 300 LED Matrix
5. Functions
01) While in main menu, turn the MENU control (04) until the display shows:
02) Press the MENU control (04) to enter the menu.
03) Turn the MENU control (04) to toggle between the 9 available functions:
•
Pan Invert
•
Tilt Invert
•
Dimmer Curve
•
DMX Fail
•
Display
•
Back Light
•
Reset
•
Factory Sets
•
Auto Test
04) Press the MENU control (04) to open the desired menu.
5.1 Pan Invert
01) Turn the MENU control (04), choose Normal and press the MENU control (04) to deactivate pan
inversion.
02) Turn the MENU control (04), choose Invert and press the MENU control (04) to activate pan inversion.
03) Press the MENU control (04) to confirm the changes.
5.2 Tilt Invert
01) Turn the MENU control (04), choose Normal and press the MENU control (04) to deactivate tilt
inversion.
02) Turn the MENU control (04), choose Invert and press the MENU control (04) to activate tilt inversion.
03) Press the MENU control (04) to confirm the changes.
Ordercode: 40060
23
Phantom 300 LED Matrix
5.3. Dimmer Curve
01) Turn the MENU control (04) to toggle between the 4 available modes:
•
Square Law
•
Linear
•
S-curve
•
InvSquare Law
02) Press the MENU control (04) to confirm the mode of your choice.
5.4. DMX Fail
With this menu you can determine the behaviour of the Phantom in case of DMX failure.
01) Turn the MENU control (04) to toggle between the 4 available modes:
•
Off (DMX signal lost, device stops)
•
Hold (DMX signal lost, device will memorize the last successfully received DMX signal and will
continue using it until DMX signal reception is restored)
•
Auto (DMX signal lost, device starts an auto program)
•
Sound (DMX signal lost, device becomes sound active)
02) Press the MENU control (04) to confirm your choice.
5.5. Display
01) Press the MENU control (04) to enter the menu.
02) Turn the MENU control (04) to toggle between the 3 options:
•
Auto Rotate (Display flips accordingly to the position of the fixture)
•
Normal
•
Inverted (horizontal flip)
03) Press the MENU control (04) to confirm your choice.
Ordercode: 40060
24
Phantom 300 LED Matrix
5.6. Back Light
01) Turn the MENU control (04) to toggle between the 3 options:
•
ON (Display continuously ON)
•
OFF (Display turns OFF after 10 seconds)
•
Adjust (Display brightness)
02) Turn the MENU control (04) to choose Adjust and press the MENU control (04) to enter the menu.
03) The display will show:
04) Turn the MENU control (04) to adjust brightness. The adjustment range is between 00-10, from dark to
brightest.
05) Press the MENU control (04) to confirm the changes.
5.7. Reset
01) Turn the MENU control (04), choose Yes and press the MENU control (04) to reset the Phantom.
02) Turn the MENU control (04), choose No and press the MENU control (04) to cancel the reset function.
5.8. Factory Sets
01) Turn the MENU control (04), choose Yes and press the MENU control (04) to restore the factory
default settings.
02) Turn the MENU control (04), choose No and press the MENU control (04) to return to the main menu.
5.9. Auto Test
01) Turn the MENU control (04), choose Test and press the MENU control (04) to perform a full test of all
the available functions.
02) Turn the MENU control (04), choose Exit and press the MENU control (04) to return to the main menu.
6. Version
01) Press the MENU control (03) to enter the menu.
02) The display is now showing the current software version, installed on the Phantom:
Ordercode: 40060
25
Phantom 300 LED Matrix
DMX Channels
12 Channels
Channel 1 – Horizontal movement (Pan)
Push the slider up, in order to move head horizontally (PAN).
Gradual head adjustment, between 0-127. The head can be turned by 540° and stopped at any position
you wish.
Channel 2 – Vertical movement (Tilt)
Push the slider, up in order to move head vertically (TILT).
Gradual head adjustment, between 0-127. The head can be turned by 270° and stopped at any position
you wish.
Channel 3 – Continuous Pan
0-15
Not functional
16-135
Clockwise rotation, from slow to fast
136-255
Counterclockwise rotation, from slow to fast
Channel 4 – Continuous Tilt
0-15
Not functional
16-135
Clockwise rotation, from slow to fast
136-255
Counterclockwise rotation, from slow to fast
Channel 5 – Dimmer
0-255
0-100%, from dark to brightest
Channel 6 – Strobe
Dimmer must be open
0-10
Off
11-128
Random strobe intensity, from low to high frequency
129-255
Linear strobe intensity, from low to high frequency
Channel 7 – Color Macro
Dimmer must be open
0-7
Not functional
8-13
Color1(R255, G000, B000, W000)
14-20
Color2(R255, G000, B000, W100)
21-27
Color3(R255, G000, B000, W200)
28-34
Color4(R255, G050, B000, W000)
35-41
Color5(R255, G150, B000, W000)
42-48
Color6(R255, G255, B000, W000)
49-55
Color7(R255, G255, B000, W075)
56-62
Color8(R000, G255, B000, W255)
63-69
Color9(R000, G255, B000, W150)
70-76
Color10(R000, G255, B000, W050)
77-83
Color11(R000, G255, B000, W000)
84-90
Color12(R000, G255, B050, W000)
91-97
Color13(R000, G255, B150, W000)
98-104
Color14(R000, G255, B255, W000)
105-111
Color15(R000, G255, B255, W075)
112-118
Color16(R000, G255, B255, W150)
119-125
Color17(R000, G100, B255, W255)
126-132
Color18(R000, G000, B255, W100)
133-139
Color19(R000, G000, B255, W050)
140-146
Color20(R000, G000, B255, W000)
147-153
Color21(R075, G000, B255, W000)
154-160
Color22(R160, G000, B255, W000)
161-167
Color23(R255, G000, B255, W000)
Ordercode: 40060
26
Phantom 300 LED Matrix
168-174
175-181
182-188
189-195
196-202
203-209
210-216
217-223
224-230
231-255
Color24(R255, G000, B175, W000)
Color25(R255, G000, B100, W000)
Color26(R255, G000, B100, W050)
Color27(R255, G000, B025, W050)
Color28(R255, G000, B025, W025)
Color29(R255, G000, B025, W000)
Color30(R000, G000, B000, W255)
Color31(R075, G075, B000, W255)
Color32(R000, G000, B100, W255)
Color33(R255, G255, B255, W255)
Channel 8 – Color Switch/Flow/Rainbow
0-12
Not functional
13-24
Color switch 1
25-36
Color switch 2
37-48
Color switch 3
49-60
Color switch 4
61-72
Color switch 5
73-84
Color switch 6
85-96
Color switch 7
97-108
Color switch 8
109-120
Color flow 1
121-132
Color flow 2
133-144
Color flow 3
145-156
Color flow 4
157-168
Color flow 5
169-180
Color flow 6
181-192
Color flow 7
193-204
Rainbow effect 1
205-216
Rainbow effect 2
217-228
Blue-red color flow
229-240
Blue-green color flow
241-255
Yellow-red color flow
Channel 9 – Color Flow Speed
0-255
From slow to fast
Dimmer must be open
CH8 must be set between 13-255
Channel 10 – Characters
Dimmer must be open, CH7 or CH8 must be open
0-7
Not functional
8-37
Digits (0-9)
38-115
Letters (A-Z)
116-255
Patterns 1-46
Channel 11 – Pattern Speed
0-255
From slow to fast
Channel 12 – Functions
0-5
No function
6-10
Show1
11-20
Show2
21-30
Show3
31-40
Show4
41-50
Show5
51-60
Show6
61-70
Show7
71-80
Show8
Ordercode: 40060
27
Phantom 300 LED Matrix
81-90
91-96
97-160
161-170
171-180
181-190
191-200
201-220
221-240
241-255
Slave1
Slave2
Sound sensitivity, from low sensitivity to high sensitivity
Pan inversion
Tilt inversion
Pan normal
Tilt normal
Pan/Tilt blackout ON
Pan/Tilt blackout OFF
Not functional
20 Channels
Channel 1 – Horizontal movement (Pan)
Push the slider up, in order to move head horizontally (PAN).
Gradual head adjustment, between 0-127. The head can be turned by 540° and stopped at any position
you wish.
Channel 2 – Pan fine 16 bit
Channel 3 – Vertical movement (Tilt)
Push the slider, up in order to move head vertically (TILT).
Gradual head adjustment, between 0-127. The head can be turned by 270° and stopped at any position
you wish.
Channel 4 – Tilt fine 16 bit
Channel 5 – Pan / Tilt speed
0-255
From minimum speed (0) to maximum speed (255)
Channel 6 – Continuous Pan
0-15
Not functional
16-135
Clockwise rotation, from slow to fast
136-255
Counterclockwise rotation, from slow to fast
Channel 7 – Continuous Tilt
0-15
Not functional
16-135
Clockwise rotation, from slow to fast
136-255
Counterclockwise rotation, from slow to fast
Channel 8 – Dimmer
0-255
0-100%, from dark to brightest
Channel 9 – Linear Strobe
Dimmer must be open
0-10
Off
11-255
Linear strobe intensity, from low to high frequency
Channel 10 – Random Strobe
Dimmer must be open
0-10
Off
11-255
Random strobe intensity, from low to high frequency
Channel 11 – Color Macro
Dimmer must be open
0-7
Not functional
8-13
Color1(R255, G000, B000, W000)
14-20
Color2(R255, G000, B000, W100)
21-27
Color3(R255, G000, B000, W200)
Ordercode: 40060
28
Phantom 300 LED Matrix
28-34
35-41
42-48
49-55
56-62
63-69
70-76
77-83
84-90
91-97
98-104
105-111
112-118
119-125
126-132
133-139
140-146
147-153
154-160
161-167
168-174
175-181
182-188
189-195
196-202
203-209
210-216
217-223
224-230
231-255
Color4(R255, G050, B000, W000)
Color5(R255, G150, B000, W000)
Color6(R255, G255, B000, W000)
Color7(R255, G255, B000, W075)
Color8(R000, G255, B000, W255)
Color9(R000, G255, B000, W150)
Color10(R000, G255, B000, W050)
Color11(R000, G255, B000, W000)
Color12(R000, G255, B050, W000)
Color13(R000, G255, B150, W000)
Color14(R000, G255, B255, W000)
Color15(R000, G255, B255, W075)
Color16(R000, G255, B255, W150)
Color17(R000, G100, B255, W255)
Color18(R000, G000, B255, W100)
Color19(R000, G000, B255, W050)
Color20(R000, G000, B255, W000)
Color21(R075, G000, B255, W000)
Color22(R160, G000, B255, W000)
Color23(R255, G000, B255, W000)
Color24(R255, G000, B175, W000)
Color25(R255, G000, B100, W000)
Color26(R255, G000, B100, W050)
Color27(R255, G000, B025, W050)
Color28(R255, G000, B025, W025)
Color29(R255, G000, B025, W000)
Color30(R000, G000, B000, W255)
Color31(R075, G075, B000, W255)
Color32(R000, G000, B100, W255)
Color33(R255, G255, B255, W255)
Channel 12 – Color Switch/Flow/Rainbow
0-12
Not functional
13-24
Color switch 1
25-36
Color switch 2
37-48
Color switch 3
49-60
Color switch 4
61-72
Color switch 5
73-84
Color switch 6
85-96
Color switch 7
97-108
Color switch 8
109-120
Color flow 1
121-132
Color flow 2
133-144
Color flow 3
145-156
Color flow 4
157-168
Color flow 5
169-180
Color flow 6
181-192
Color flow 7
193-204
Rainbow effect 1
205-216
Rainbow effect 2
217-228
Blue-red color flow
229-240
Blue-green color flow
241-255
Yellow-red color flow
Channel 13 – Color Flow Speed
0-255
From slow to fast
Ordercode: 40060
Dimmer must be open
CH12 must be set between 13-255
29
Phantom 300 LED Matrix
Channel 14 – Characters
Dimmer must be open, CH11 or CH12 must be open
0-7
Not functional
8-37
Digits (0-9)
38-115
Letters (A-Z)
116-255
Patterns 1-46
Channel 15 – Pattern Speed
0-255
From slow to fast
Channel 16 – Functions
0-5
No function
6-10
Show1
11-20
Show2
21-30
Show3
31-40
Show4
41-50
Show5
51-60
Show6
61-70
Show7
71-80
Show8
81-90
Slave1
91-96
Slave2
97-160
Sound sensitivity, from low sensitivity to high sensitivity
161-170
Pan inversion
171-180
Tilt inversion
181-190
Pan normal
191-200
Tilt normal
201-220
Pan/Tilt blackout ON
221-240
Pan/Tilt blackout OFF
241-255
Not functional
Channel 17 – Red color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment Red, from 0 – 100%
Channel 18 – Green color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment Green, from 0 – 100%
Channel 19 – Blue color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment Blue, from 0 – 100%
Channel 20 – White color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment White, from 0 – 100%
Ordercode: 40060
30
Phantom 300 LED Matrix
120 Channels
Channel 1 – Horizontal movement (Pan)
Push the slider up, in order to move head horizontally (PAN).
Gradual head adjustment, between 0-127. The head can be turned by 540° and stopped at any position
you wish.
Channel 2 – Pan fine 16 bit
Channel 3 – Vertical movement (Tilt)
Push the slider, up in order to move head vertically (TILT).
Gradual head adjustment, between 0-127. The head can be turned by 270° and stopped at any position
you wish.
Channel 4 – Tilt fine 16 bit
Channel 5 – Pan / Tilt speed
0-255
From minimum speed (0) to maximum speed (255)
Channel 6 – Continuous Pan
0-15
Not functional
16-135
Clockwise rotation, from slow to fast
136-255
Counterclockwise rotation, from slow to fast
Channel 7 – Continuous Tilt
0-15
Not functional
16-135
Clockwise rotation, from slow to fast
136-255
Counterclockwise rotation, from slow to fast
Channel 8 – Dimmer
0-255
0-100%, from dark to brightest
Channel 9 – Linear Strobe
Dimmer must be open
0-10
Off
11-255
Linear strobe intensity, from low to high frequency
Channel 10 – Random Strobe
Dimmer must be open
0-10
Off
11-255
Random strobe intensity, from low to high frequency
Channel 11 – Color Macro
Dimmer must be open
0-7
Not functional
8-13
Color1(R255, G000, B000, W000)
14-20
Color2(R255, G000, B000, W100)
21-27
Color3(R255, G000, B000, W200)
28-34
Color4(R255, G050, B000, W000)
35-41
Color5(R255, G150, B000, W000)
42-48
Color6(R255, G255, B000, W000)
49-55
Color7(R255, G255, B000, W075)
56-62
Color8(R000, G255, B000, W255)
63-69
Color9(R000, G255, B000, W150)
70-76
Color10(R000, G255, B000, W050)
77-83
Color11(R000, G255, B000, W000)
84-90
Color12(R000, G255, B050, W000)
91-97
Color13(R000, G255, B150, W000)
98-104
Color14(R000, G255, B255, W000)
105-111
Color15(R000, G255, B255, W075)
Ordercode: 40060
31
Phantom 300 LED Matrix
112-118
119-125
126-132
133-139
140-146
147-153
154-160
161-167
168-174
175-181
182-188
189-195
196-202
203-209
210-216
217-223
224-230
231-255
Color16(R000, G255, B255, W150)
Color17(R000, G100, B255, W255)
Color18(R000, G000, B255, W100)
Color19(R000, G000, B255, W050)
Color20(R000, G000, B255, W000)
Color21(R075, G000, B255, W000)
Color22(R160, G000, B255, W000)
Color23(R255, G000, B255, W000)
Color24(R255, G000, B175, W000)
Color25(R255, G000, B100, W000)
Color26(R255, G000, B100, W050)
Color27(R255, G000, B025, W050)
Color28(R255, G000, B025, W025)
Color29(R255, G000, B025, W000)
Color30(R000, G000, B000, W255)
Color31(R075, G075, B000, W255)
Color32(R000, G000, B100, W255)
Color33(R255, G255, B255, W255)
Channel 12 – Color Switch/Flow/Rainbow
0-12
Not functional
13-24
Color switch 1
25-36
Color switch 2
37-48
Color switch 3
49-60
Color switch 4
61-72
Color switch 5
73-84
Color switch 6
85-96
Color switch 7
97-108
Color switch 8
109-120
Color flow 1
121-132
Color flow 2
133-144
Color flow 3
145-156
Color flow 4
157-168
Color flow 5
169-180
Color flow 6
181-192
Color flow 7
193-204
Rainbow effect 1
205-216
Rainbow effect 2
217-228
Blue-red color flow
229-240
Blue-green color flow
241-255
Yellow-red color flow
Channel 13 – Color Flow Speed
0-255
From slow to fast
Dimmer must be open
CH12 must be set between 13-255
Channel 14 – Characters
Dimmer must be open, CH11 or CH12 must be open
0-7
Not functional
8-37
Digits (0-9)
38-115
Letters (A-Z)
116-255
Patterns 1-46
Channel 15 – Pattern Speed
0-255
From slow to fast
Channel 16 – Functions
0-5
No function
Ordercode: 40060
32
Phantom 300 LED Matrix
6-10
11-20
21-30
31-40
41-50
51-60
61-70
71-80
81-90
91-96
97-160
161-170
171-180
181-190
191-200
201-220
221-240
241-255
Show1
Show2
Show3
Show4
Show5
Show6
Show7
Show8
Slave1
Slave2
Sound sensitivity, from low sensitivity to high sensitivity
Pan inversion
Tilt inversion
Pan normal
Tilt normal
Pan/Tilt blackout ON
Pan/Tilt blackout OFF
Not functional
Channel 17 – Red color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment Red, from 0 – 100%
Channel 18 – Green color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment Green, from 0 – 100%
Channel 19 – Blue color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment Blue, from 0 – 100%
Channel 20 – White color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment White, from 0 – 100%
Ordercode: 40060
33
Phantom 300 LED Matrix
Channel 21 – LED 1 Red color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment Red, from 0 – 100%
Channel 22 – LED 1 Green color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment Green, from 0 – 100%
Channel 23 – LED 1 Blue color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment Blue, from 0 – 100%
Channel 24 – LED 1 White color intensity
Dimmer must be open, CH11 and CH12 must be closed
0-255
Gradual adjustment White, from 0 – 100%
•
•
•
•
•
•
•
•
•
Channel 117 – LED 25 Red color intensity
Dimmer must be open; CH11, CH12 must be closed
0-255
Gradual adjustment Red, from 0 – 100%
Channel 118 – LED 25 Green color intensity
Dimmer must be open; CH11, CH12 must be closed
0-255
Gradual adjustment Green, from 0 – 100%
Channel 119 – LED 25 Blue color intensity
Dimmer must be open; CH11, CH12 must be closed
0-255
Gradual adjustment Blue, from 0 – 100%
Channel 120 – LED 25 White color intensity
Dimmer must be open; CH11, CH12 must be closed
0-255
Gradual adjustment White, from 0 – 100%
Ordercode: 40060
34
Phantom 300 LED Matrix
Maintenance
The Showtec Phantom 300 LED Matrix requires almost no maintenance. However, you should keep the
unit clean. Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power
supply and then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner
and a soft cloth. Do not use alcohol or solvents. The front glass panel will require weekly cleaning, as
smoke-fluid tends to build up residues, reducing the light output very quickly. Do not immerse in liquid.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying
electric power.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must
not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the
fuse burns out, the product will not function whatsoever. If this happens, follow the directions below to do
so.
01) Unplug the unit from electric power source.
02) Insert a screwdriver into the slot in the fuse cover. Turn the fuse holder counterclockwise. The fuse will
come out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse holder. Be sure
to use a fuse of the same type and specification. See the product specification label for details.
Troubleshooting
No Light
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply, the LEDs, the fuse.
01) Power supply. Check if the unit is plugged into an appropriate power supply.
02) The LEDs. Return the Phantom 300 LED Matrix to your Showtec dealer.
03) The fuse. See page 35 for replacing the fuse
04) If all of the above appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the Phantom 300 LED Matrix,
as this may damage the unit and the warranty will become void.
06) Return the device to your Showtec dealer.
Ordercode: 40060
35
Phantom 300 LED Matrix
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
Problem
One or more
fixtures do not
function at all
Fixtures reset
correctly, but all
respond
erratically or not
at all to the
controller
Probable cause(s)
Solution
No power to the fixture
Primary fuse blown
The controller is not connected.
3-pin XLR Out of the controller
does not match XLR Out of the first
fixture on the link (i.e. signal is
reversed)
•
Check if power is switched on and
cables are plugged in
•
•
Replace fuse
Connect controller.
•
Install a phase reversing cable
between the controller and the
first fixture on the link
•
Check data quality. If much lower
than 100 percent, the problem
may be a bad data link
connection, poor quality or
broken cables, missing termination
plug, or a defective fixture
disturbing the link
Inspect connections and cables.
Correct poor connections. Repair
or replace damaged cables
Insert termination plug in output
jack of the last fixture on the link
Check address setting
Bypass one fixture at a time until
normal operation is restored:
unplug both connectors and
connect them directly together.
Have the defective fixture
serviced by a qualified technician
Install a phase-reversing cable
between the fixtures or swap pin 2
and 3 in the fixture that behaves
erratically
Allow the fixture to cool down
Clean the fans
Make sure air vents in control
panel and the front lens are not
blocked
Turn up the air conditioning
Disconnect the fixture and return it
to your dealer
Disconnect fixture. Check settings
and correct if necessary
Poor data quality
Fixtures reset
correctly, but
some respond
erratically or not
at all to the
controller
•
Bad data link connection
Data link not terminated with 120
Ohm termination plug
Incorrect addressing of the fixtures
One of the fixtures is defective and
disturbs data transmission on the
link
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed)
•
•
•
•
LEDs damaged
The power supply settings do not
match local AC voltage and
frequency
Ordercode: 40060
•
•
•
•
•
Fixture is too hot
No light or lamp
cuts out
intermittently
•
36
•
Phantom 300 LED Matrix
Product Specifications
Model:
Input voltage:
Power consumption:
DMX linking:
Fuse:
Dimensions:
Weight:
Showtec Phantom 300 LED Matrix
100-240V AC, 60/50Hz
340W
30pcs
T5L/250V
230 x 395 x 480 mm (LxWxH)
13 kg
Operating and Programming:
Signal pin OUT:
DMX Mode:
Signal input:
Signal output:
Pin 1 (earth), pin 2 (-), pin 3 (+)
12, 20, 120 channels
3-pin XLR/RJ45 IN
3-pin XLR/RJ45 OUT
Electro-mechanical effects:
Light source:
Light output:
Colormixing:
Beam angle:
Pan/Tilt range
Dimmer:
Strobe:
DMX-control:
Onboard:
Control:
25 x 10W RGBW 4-in-1 LEDs
44950 lux @ 2 m
RGBW
15°
540°/270°
0-100%
0-20Hz
via standard DMX-controller
LCD display for easy setup
Auto, Manual, Sound-controlled, Master/Slave, DMX512, ArtNet
Black metal & flame-retardant plastic
Pro Power connector IN/OUT
Linear, Square, I-Square, S-curve
Pan/Tilt inversion
Internal fans
Schuko to Pro Power connector cable (length 1,5 m)
and 2 mounting brackets with quick-locks
Housing:
Connections:
Dimmer curves:
Special:
Cooling:
Included:
Max. ambient temperature t a :
Max. housing temperature t B :
40°C
80°C
Minimum distance:
Minimum distance from flammable surfaces:
Minimum distance to lighted object:
0,5 m
1m
Website: www.Showtec.info
Email: service@highlite.nl
Ordercode: 40060
37
Phantom 300 LED Matrix
Dimensions
Ordercode: 40060
38
©2016 Showtec
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising