advertisement
The Cobra line of quality products includes:
CB Radios microTALK
®
Radios
Radar/Laser Detectors
Safety Alert
®
Traffic Warning Systems
Mobile GPS Navigation Systems
HighGear
®
Accessories
CobraMarine
®
VHF Radios
Marine Chartplotters
Power Inverters
Accessories
For more information or to order any of our products, please visit our website: www.cobra.com
Nothing Comes Close to a Cobra ® English
14 BAND ™
HIGH-PERFORMANCE
DIGITAL RADAR/LASER
DETECTOR WITH XTREME RANGE
SUPERHETERODYNE ® TECHNOLOGY
XRS 9345
Nothing Comes Close to a Cobra ®
Operating Instructions
Printed in China
Part No. 480-488-P
Version A
English
Main Icons
Important Information and
Customer Assistance
Introduction
Intro Operation Customer Warranty
Federal Laws Governing the Use of Radar Detectors
It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene this Act, while
Secondary Icons illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action.
Safety Alert
Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. It is only intended to alert
Notice the motorist that an emergency vehicle equipped with a Cobra Safety Alert transmitter is within range as defined by that product. Please call local fire and police departments to learn if coverage exists in your area.
Safe Driving
Motorists, as well as operators of emergency or service vehicles, are expected to exercise all due caution while using this product, and to obey all applicable traffic laws.
Security of Your Vehicle
Before leaving your vehicle, always remember to conceal your radar detector in order to reduce the possibility of break-in and theft.
•
Customer Assistance
Intro Operation Customer
Assistance
Warranty
Customer Assistance
•
Should you encounter any problems with this product, or not understand its many features, please refer to this owner’s manual. If you require further assistance after reading this manual, Cobra Electronics offers the following customer assistance services:
Secondary Icons
For Assistance in the U.S.A.
Automated Help Desk English only. 24 hours a day, 7 days a week 773-889-3087 (phone).
Customer Assistance Operators English and Spanish. 8:00 a.m. to 6:00 p.m. Central Time
Mon. through Fri. (except holidays) 773-889-3087 (phone).
Questions English and Spanish. Faxes can be received at 773-622-2269 (fax).
Notice
Technical Assistance English only. www.cobra.com (on-line: Frequently Asked
Questions). English and Spanish. [email protected] (e-mail).
For Assistance Outside the U.S.A.
Contact Your Local Dealer
©2009 Cobra Electronics Corporation
6500 West Cortland Street
Chicago, Illinois 60707 USA www.cobra.com
A1 English
Introduction
Intro
Controls, Indicators and Connections
Operation Customer Warranty
Secondary Icons
Windshield Bracket
Release Button
Notice
Windshield
Bracket
Mount
•
LaserEye
For 360° detection of laser signals.
Audio Jack
Speaker
12V DC
Power Jack
On-Off/ Volume Control
Allows you to adjust the volume of the tone alerts.
Main Icons
Dim Button
Allows you to adjust the UltraBright
Data Display brightness for easy reading. (Also turns VG-2 and
Spectre I & IV+ alerts On and Off.*)
Intro Operation Customer
Assistance
IntelliMute Button
Engine RPM sensing mute function which reduces false alerts. Button turns IntelliMute On and Off. (Also enters IntelliMute setting mode.*)
Secondary Icons
City Button
For City or Highway modes to reduce false alerts. (Also turns Ku alerts On and Off.*)
Warranty
Mute Button
For manual mute or auto mute of audio alerts.
* Press and hold for four seconds to access these functions.
Notice
WARNING
Modifications or parts substitutions not approved by Cobra Electronics Corporation may violate
FCC Rules and void your authority to operate this equipment.
A2 English
Introduction
Display
Intro
Display and Product Features
Operation
Secondary Icons
Customer
Assistance
Warranty
•
X K Ka V S
Secondary Icons
L
Notice
NOTE: In This Manual
When steady, the display will be shown:
X K Ka V S c
Radar, VG-2,
Spectre I & IV+ and
Safety Indicators
Signal
Strength,
Pop, Laser,
City/Highway and
Mode Indicators
Signal Strength: 1 (weakest) to 5 (strongest)
IntelliMute
Indicator
When blinking, the display will be shown:
X & K will light simultaneously when indicating
Ku detection:
X K Ka V S c
X K Ka V S c
Product Features
•
Congratulations! You’ve made a smart choice by purchasing a high performance radar/laser detector from Cobra. Just look at some of the sophisticated features and capabilities your new unit includes:
Xtreme Range
Superheterodyne Technology
With super-fast sweep circuitry,
XRS provides extra detection range and the best possible advance warning to even the fastest radar guns
UltraBright Data Display
Easy-to-read with adjustable brightness
City or Highway
Modes to reduce false alerts
Detection and Separate Alerts For:
Radar signals (X, K, Ka and Ku bands, with signal strength indicated), Laser signals, Safety Alert signals, VG-2 signals, Spectre I & IV+ signals
Alert Programming
Easy setting of radar bands to be monitored
Safety Alert
Traffic warning system distinguishes important safety alerts from other
K band signals
LaserEye
For 360° detection of laser signals
Manual Mute or Auto Mute
A mute function of audio alerts
Instant-On Ready
Detects radar guns with “instant-on”
(very fast) speed monitoring capabilities
IntelliMute
A mute function reduces false audio alerts by sensing engine RPMs
Pop Detection
Detects the latest super-fast instant-on single pulse radar guns
IntelliMute Pro
Prevents detection by radar detector detectors
(RDDs) when traveling at slower speeds
Tone Alerts
With adjustable volume
Mounting
Mounts easily on windshield or dashboard
This booklet describes the simple steps for mounting and setting up your detector. It also provides helpful information about how radar and laser guns are used and how you can interpret the alerts you receive.
Nothing Comes Close to a Cobra ® A3
Intro
Secondary Icons
Accessories Order Info and
Trademark Acknowledgement
Customer Assistance
Operation Customer Warranty
Assistance
Ordering From U.S.A.
Call 773-889-3087 for pricing or visit www.cobra.com.
For Credit Card Orders
Call 773-889-3087 [Press one from the main menu] 8:00 a.m. to 6:00 p.m. Central Time,
Monday through Friday.
Make Check or Money Order Payable To
Cobra Electronics, Attn: Accessories Dept.,
6500 West Cortland Street, Chicago, IL 60707 U.S.A.
To Order Online
Please visit our website: www.cobra.com.
Notice
Item # Description
420-030-N-001 Straight 12V Power Cord
420-026-N-001 Coiled 12V Power Cord
545-159-N-001 Windshield Mounting Bracket
CLP-2B Dual Port Power Adapter
Trademark Acknowledgement
•
Cobra ® , DigiView ® , EasySet ® , Extra Sensory Detection ® , IntelliMute ® , IntelliMute Pro ® ,
IntelliShield ® , LaserEye ®
System, Strobe Alert ®
, Nothing Comes Close to a Cobra ®
, VG-2 Alert ®
, Safety Alert
, Xtreme Range Superheterodyne ®
® Traffic Warning and the snake design are registered trademarks of Cobra Electronics Corporation, USA.
Cobra Electronics Corporation™, 14 Band™, 15 Band™, Extreme Bright DataGrafix™,
IntelliLink™, Revolution™ Series, SmartPower™, Spectre Alert™, Super-Xtreme Range
Superheterodyne™, S-XRS™, UltraBright™, and Voice Alert™ are trademarks of Cobra
Electronics Corporation, USA.
Opticom™ is a trademark of 3M Corporation. Instaclear ® for Ford is a registered trademark of Ford Motor Company, Inc. Electriclear ® for GM is a registered trademark of
General Motors Corporation. 20-20™ and Ultra-Lyte™ are trademarks of Laser Technology,
Inc. ProLaser™ and ProLaser III™ are trademarks of Kustom Signals, Inc. Bee III™ and
Pop™ are a trademarks of MPH Industries. Stalker™ LIDAR is a trademark of Applied
Concepts, Inc. Spectre I™ and Spectre IV+™ are trademarks of Stealth Micro Systems Pty. Ltd.
SpeedLaser™ is a trademark of Laser Atlanta, LLC. Interceptor VG-2™ is a trademark of
TechniSonic Industries LTD. Tomar ® is a registered trademark of TOMAR Electronics, Inc.
Nothing Comes Close to a Cobra ® 25
N
Main Icons
Main Icons
Introduction
Contents
Intro Operation Customer
Assistance
Warranty
Introduction
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1
Intro
Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1
Operation Customer Warranty
Controls, Indicators and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2
Secondary Icons
Assistance
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
Intro
Secondary Icons
Secondary Icons
Operation
Notice
Your Detector
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Customer Warranty
Auxiliary Audio Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Highway/City Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
UltraBright Data Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Muting an Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Auto Mute Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
IntelliMute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
IntelliMute Pro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
VG-2 and Spectre I & IV+ Alert Settings . . . . . . . . . . . . . . . . . . . . . . . . . 13
Pop Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Radar Alert Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Signals Detected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Audio Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Visual Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Instant-On Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Responding to Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Understanding Radar and Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Customer
Assistance
Operation
Warranty
Limited 1-Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Warranty
Customer Assistance
Product Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Customer
Assistance
Trademark Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Nothing Comes Close to a Cobra ® 1
N
Installation
Your Detector
Intro Operation Customer
Installation
Assistance
Warranty
Where to Mount Your Unit
You will get optimum performance from your detector if you Mount it at a point approximately in the center of the vehicle, as low as possible on the
Secondary Icons front windshield without obstructing the unit’s view of the road either to the front or rear. Make sure unit is level with the road. You can also mount it directly on the dashboard.
•
Notice
Windshield Mounting Dashboard Mounting
The unit’s lens must not be blocked and the LaserEye should have a clear view out the back window to allow 360° detection.
The LaserEye Should Have a Clear View
Radar and laser signals pass through glass but not through other materials and objects. Objects that can block or weaken incoming signals include:
■
Windshield wiper blades
■
Mirrored sun screens
■
Dark tinting at the top of the windshield
■
Heated windshields currently available on some vehicles
(Instaclear for Ford, Electriclear for GM.) Consult your dealer to see if you have this option.
2 English
Installation
Your Detector
Intro Operation Customer
Assistance
Windshield Mounting
Warranty
1.
Attach the rubber cups to the bracket.
Secondary Icons
Notice
2. Make sure the rubber cups and your windshield are clean.
3. Push the bracket firmly onto the windshield.
4. Attach the detector to the bracket. Check the angle of the unit.
5. To adjust the angle if necessary, gently push or pull on the bracket to bend it. DO NOT use the detector to bend the bracket.
6. Plug the power cord into the detector.
7. Plug the cigarette lighter adapter on the power cord into your vehicle’s cigarette lighter.
8. You can temporarily remove the detector whenever you wish by pressing the bracket release button and sliding it off the bracket.
Nothing Comes Close to a Cobra ® 3
Installation
Your Detector
Intro Operation Customer
Assistance
Dashboard Mounting
Warranty
Secondary Icons
1.
Place the detector on the dashboard to find a location where the unit has a clear, level view of the road.
The angle can NOT be adjusted after mounting.
2. Remove the paper backing from one side of the hookand-loop fastener.
Notice
3. Attach the pad to the dashboard at your chosen location and remove the other paper backing.
4. Attach the detector to the hook-and-loop fastener.
You can remove and reattach the unit as often as you like.
6. Plug the power cord into the detector.
7. Plug the cigarette lighter adapter on the power cord into your vehicle’s cigarette lighter.
Your Detector
Intro Operation
Getting Started
Customer Warranty
Power On
X K Ka V S
Secondary Icons h
Main Icons
Intro
Secondary Icons
On-Off/
Volume Control
Notice
Rotate clockwise
(away from you)
W
Ca
No m
Cu
As
W m
As
Se
Cu
Operation Customer Warranty To Turn On the Unit and Adjust the Audio Volume
Op
Rotate the On-Off/
Volume control clockwise (away from you).
Tone
Three beeps
M
Visual Display h appears in the display indicating that the power is On
Notice
NOTE
In some vehicles, power is supplied to the cigarette lighter even while the ignition is Off. If this is the case with your vehicle, you should turn Off or unplug your detector when parking for lengthy periods.
Auxiliary Audio Jack
The Auxiliary Audio Jack can be used to connect external speakers in environments with high ambient noise levels. The internal speaker will be disconnected. (This uses a mini stereo audio connector.)
•
•
4 English
Auxiliary
Audio Jack
Nothing Comes Close to a Cobra ® 5
Settings
Your Detector
Intro Operation
Settings
Customer
Assistance
Warranty
When changing the Settings on your detector, please keep in mind:
■
Buttons can have multiple functions.
All settings will be stored in memory when the power is turned Off and recalled when the power is turned back On.
Highway/City Mode
Setting your detector to City mode delays all X band audio alerts until the signal strength reaches Level 3. (A single beep will sound when the
Notice signal is first detected.) This will reduce false alerts while you are driving in, or near, urban areas where there are many sources for conflicting
X band signals such as microwave towers and automatic door openers.
To change settings, follow the procedure listed below, which indicates what you will see and hear as you complete each step. The factory setting is Highway mode.
Highway Mode
City Button
Press and release
X K Ka V S h
•
City Mode
X K Ka V S c
To Change From Highway Mode to City Mode
Press and release the City button.
Tone
One beep
Visual Display c appears in the display
To Change From City Mode Back to Highway Mode
Press and release the City button again.
Tone
Two beeps
Visual Display h appears in the display
6 English
Your Detector
Intro Operation
Settings
Customer Warranty
You can choose from three settings for Brightness of the display.
You can cycle through the settings by repeatedly pushing the Dim button.
The factory setting is Bright.
Secondary Icons
Bright
Press and
Notice
Dark button
Dim
Dim Button
Press and release
To Change the Brightness to Dim
Press and release the Dim button once.
Tone
One beep
To Change the Brightness to Dark
Press and release the Dim button again.
Tone
One beep
Visual Display
Display dims
Visual Display
Display remains dim
(no visual alerts will be seen)
To Change the Brightness to Bright
Press and release the Dim button a third time.
Tone
Two beeps
Visual Display
Display returns to full brightness
Nothing Comes Close to a Cobra ® 7
Your Detector
Intro Operation
Settings
Customer Warranty
Your detector allows you to quickly turn Off an audio Alert by momentarily pressing the Mute button. If you press the Mute button a second time during the Alert, the audio Alert will be turned back on.
Secondary Icons
Auto Mute Mode
Auto Mute will automatically reduce the audio volume of all alerts after four seconds for as long as the signal is detected. The factory setting for Auto Mute is on.
Notice
Main Icons
Intro
Secondary Icons
Settings
Your Detector
Intro Operation
IntelliMute
Customer
Assistance
Warranty
IntelliMute is a unique feature that allows you to avoid alerts you don’t need to hear because you are stopped or moving slowly. By sensing the “revs”
(RPMs) of your engine, IntelliMute knows when you are at low speed and
Operation Customer Warranty
Assistance
Before IntelliMute will work, you must set an activation point for your engine’s revs (see page 10). Whenever the revs are below that point, IntelliMute will begin muting. The activation point will be stored in memory and recalled each time the power is turned on. The factory setting is IntelliMute Off.
Notice
Notice
NOTE
IntelliMute may not work with some vehicles because it cannot sense the engine’s revs. In such cases, you can reduce unwanted audio alerts by using Auto Mute and City mode when appropriate.
Mute Button
Press and release
To Turn Auto Mute On
Press and release the Mute button again while no alert is occurring.
Tone
Two beeps
To Turn Auto Mute Off
Press and release the Mute button while no alert is occurring.
Tone
One beep
Visual Display
None
Visual Display
None
IntelliMute Button
Press and release
To Turn IntelliMute On
Press and release the IntelliMute button.
Tone
Two beeps
To Turn IntelliMute Off
Press and release the IntelliMute button again.
Tone
One beep
Visual Display
Dot appears next to the large character on the right
Visual Display
None
8 English Nothing Comes Close to a Cobra ® 9
Your Detector
Intro Operation
Settings
Customer Warranty in Icons
IntelliMute works with both City and Auto Mute modes.
Whenever your engine revs are below the activation point, the dot next to the large character on the right side of the display will remain lit.
Secondary Icons
Above the activation point, the dot will blink twice every two seconds.
Below Activation Point Above Activation Point in Icons
Intro
X K Ka V S c
Operation Customer Warranty
X K Ka V S c
Intro condary Icons
If, for any reason, the unit stops sensing your engine’s revs,
IntelliMute will indicate an error and automatically turn Off.
Operation Customer Warranty power is turned Off and recalled each time the power is turned On.
condary Icons
Operation
Notice
NOTE
The rev point must be reset if you use your detector in a different vehicle.
NOTE
When initially choosing your IntelliMute activation point, a setting
Notice of approximately 300 to 600 RPMs above idle is recommended.
Customer
Assistance
Warranty You can reset the activation point at any time to fit your individual preferences and driving style.
Installation
Setting the IntelliMute Activation Point
Customer
Assistance
Your detector must be installed in your vehicle.
Notice Caution
CAUTION
Do not attempt to set the rev point while driving.
Your vehicle should be parked and idling.
Warning
IntelliMute must be turned on before setting the activation point. You will hear a series of beeps as you follow the steps on the next page.
10 English
Your Detector
Intro Operation
IntelliMute Button
Press and hold for two seconds
Settings
Warranty Customer
Assistance
Secondary Icons
To Set the IntelliMute Activation Point
Press and hold the IntelliMute button for two seconds.
Notice
Tone
Two beeps
Rev your engine to
Main Icons the level you wish to set (recommend slightly above idle)
None and hold revs steady for two seconds.
Intro
At the desired
Operation rev level, press and release the
IntelliMute button.
Secondary Icons
Customer Warranty
Visual Display
None
Main Icons
Main Icons
Three bars will
Intro Operation flash in succession
Customer
Assistance
Intro Operation
Warranty
1 Customer
Installation
3
Secondary Icons
Main Icons Main Icons
Customer
Assistance
Customer
Assistance
Notice Caution
All three bars flash
Customer Intro
Assistance three times
1
Customer
Assistance
Secondary Icons Secondary Icons
Notice
Warning
Caution
Customer
Assistance
Warranty
Customer
Assistance
Warranty
Warning
Notice Caution
Notice
NOTE
If the unit is unable to sense usable pulses within three seconds or if you do not set a rev point within
20 seconds of beginning these steps, IntelliMute will indicate an error and automatically turn Off.
Caution Warning
Tone
Four beeps
Visual Display
E appears
X K Ka V S
E
Nothing Comes Close to a Cobra ® 11
Your Detector
Intro Operation
Settings
Customer Warranty
IntelliMute Pro prevents detection by radar detector detectors (RDDs) such as
VG-2, Spectre I and Spectre IV+ when traveling at slower speeds. It is intended for use by experienced users only.
Operation Customer Warranty
When IntelliMute Pro is turned On, and engine RPMs are below the IntelliMute activation point, your detector’s radar detection circuits are turned Off to prevent detection by RDDs.
Installation
Customer Before IntelliMute Pro can be turned On, you must have turned On and Set the
Assistance
IntelliMute activation point. (See pages 9 through 11.)
Notice
Notice Caution
CAUTION
When IntelliMute Pro is On, NO radar signals will be detected and
NO alerts will be given at RPMs below the IntelliMute activation point.
Warning
IntelliMute Button
City Button
Press and hold both buttons simultaneously
IntelliMute Pro On
X K Ka V S c
To Turn IntelliMute Pro On
While no signal is being detected, press and hold both the IntelliMute and
City buttons for four seconds.
Tone
Two beeps
To Turn IntelliMute Pro Off
Press and hold both the IntelliMute and
City buttons for four seconds.
Tone
One beep
Visual Display c or h will blink
Visual Display c or h will show steady
12 English
Your Detector
Intro Operation
Settings
Customer Warranty
Police use radar detector detectors (RDDs) to spot users of radar detectors.
Your detector is able to identify signals from VG-2, Spectre I and Spectre IV+
RDDs and can provide alerts when any of these or similar devices are in use
Your detector can be spotted by Spectre IV+ RDDs, but is invisible to VG-2 and
Spectre I RDDs. You can choose whether you want to be alerted to VG-2 and
Spectre I & IV+ RDD signals. The factory setting for VG-2 and Spectre I & IV+ alerts is Off.
Notice
On/Off Indicator
X K Ka V S c
Dim Button
Press and hold for four seconds
To Turn VG-2 and Spectre I & IV+ Alerts On and Off
While no signal is being detected, press and hold the Dim button for four seconds.
Tone
On = Two beeps
Off = One beep
Visual Display
V will blink twice in the display
V will blink once in the display
Pop Alert
The Pop Mode Radar Gun is a single-pulse Doppler radar that is a feature of a K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses a single, short-time pulse to measure the target vehicle’s speed.
The Pop mode receiver senses Pop singles beyond the effective range of
Pop radar guns. As the Pop mode receiver is so sensitive, you should limit the use of Pop Detect mode to highway and rural driving.
Pop Alert will alert you to Pop radar signals. During the alert, the unit continues to detect other signals. The factory setting is Pop Detect Off.
To Turn Pop Alert On and Off
While no signal is being detected, press and hold both the
Dim and City buttons for four seconds.
Tone
Pop On = Two beeps
Pop Off = One beep
Visual Display
P will blink twice in the display
P will blink once in the display
Nothing Comes Close to a Cobra ® 13
Your Detector
Intro Operation
Settings
Customer Warranty
The detector allows you to choose whether it will show alerts on the X, K and
Ku bands. The factory settings are: X Band and K Band On; Ku Band Off.
To Turn X Band On and Off
Secondary Icons
While no signal is being detected, press and hold both the
Dim and Mute buttons for four seconds.
Notice
Tone
X On = Two beeps
X Off = One beep
To Turn K Band On and Off
While no signal is being detected, press and hold both the
Mute and City buttons for four seconds.
Tone
K On = Two beeps
K Off = One beep
Visual Display
X will blink twice in the display
X will blink once in the display
Visual Display
K will blink twice in the display
K will blink once in the display
To Turn Ku Band On and Off
While no signal is being detected, press and hold the City button for four seconds.
Tone
Ku On = Two beeps
Ku Off = One beep
Visual Display
X and K will blink twice in the display
X and K will blink once in the display
14 English
Detection
Your Detector
Intro Operation
Detection
Customer
Assistance
Warranty
Signals Detected
The tables on the following pages show you the types of Signals your detector will detect, as well as the visual alerts it provides for each of them.
Secondary Icons
•
Audio Alerts
A distinctly different Alert tone is used for each type of signal detected
(including separate tones for each laser signal). For X, K, Ka and Ku band radar signals, the tones will repeat faster as you approach the signal
Notice source. The repeat rate of the tones gives you useful information about the signal detected. (See responding to alerts on page 18.)
Visual Display
An indication of the type of signal detected will appear in the UltraBright data Display. During X, K, Ka and Ku alerts, a number will also appear, indicating the strength of the signal detected. (1 = weakest, 5 = strongest)
X Signal Detected K Signal Detected Ka Signal Detected Ku Signal Detected
X K Ka V S
2
X K Ka V S
3
X K Ka V S
5
X K Ka V S
4
During pop alerts, the letter P will appear; and during laser alerts, the letter L will appear, instead of the signal strength indication.
POP Signal Detected
X K Ka V S
P
Laser Signal Detected
X K Ka V S
L
During VG-2 or Spectre I or IV+ alerts, the letter V will appear.
It will be steady during VG-2 and blink during Spectre I or IV+.
VG-2 Alert Signal
Detected
X K Ka V S c
During Safety Alert the letter S will appear.
Safety Alert Signal Detected
X K Ka V S c
Spectre I or IV+ Alert
Signal Detected
X K Ka V S c
Nothing Comes Close to a Cobra ® 15
Detection
Your Detector
Intro Operation Customer Warranty
Assistance
Radar Signals and Visual Displays
Type of Signal
Secondary Icons
X Band Radar
K Band Radar
Ka Band Radar
Ku Band Radar
Pop Radar
Notice
X Signal Detected K Signal Detected
X K Ka V S
2
X K Ka V S
3
POP Alert Signal Detected
X K Ka V S
P
Visual Display
X and Signal Strength
K and Signal Strength
Ka and Signal Strength
X K and Signal Strength
P is Steady
Ka Signal Detected
X K Ka V S
5
Ku Signal Detected
X K Ka V S
4
Laser Signals and Visual Displays
Type of Signal
Main Icons
Intro
Visual Display
LTI 20-20*
LTI Ultra-Lyte*
Kustom Signals ProLaser*
L is Steady
L is Steady
L is Steady
Kustom Signals ProLaser III*
Stalker LIDAR*
L is Steady
L is Steady
Laser Atlanta - Speedlaser* L is Steady
Operation Customer Warranty
Assistance
* Your detector provides 360˚ detection of these signals.
Laser Signal Detected
Secondary Icons X K Ka V S
L
Notice
NOTE
Beep rate changes with different laser alerts.
16 English
Detection
Your Detector
Intro Operation Customer Warranty
Main Icons Assistance
Safety Alert Signals and Visual Displays
Type of Signal
Secondary Icons
Intro
Emergency Vehicles
Road Hazards
Operation Customer
Assistance
Trains
Warranty
Safety Alert Signal Detected
Secondary Icons
Notice
X K Ka V S c
Visual Display
S is Steady
S is Steady
S is Steady
Notice
NOTE
There are different tones for each Safety Alert.
Main Icons
VG-2 and Spectre I or IV+ Alert Signals and Visual Displays
Type of Signal Visual Display
Intro
Interceptor VG-2
Operation Customer
Assistance
Spectre I or IV+
Warranty
V is Steady
V Blinks
VG-2 Alert Signal Detected Spectre I or IV+ Alert Signal Detected
Secondary Icons X K Ka V S c X K Ka V S c
Notice
NOTE
There are different tones for each alert.
Nothing Comes Close to a Cobra ® 17
Intro Operation Customer
Assistance
Your Detector
Intro Operation
Warranty
Detection
Customer Warranty condary Icons
Your detector is designed to detect Instant-On speed monitoring signals, which can suddenly appear at full strength.
Secondary Icons
Notice
NOTE
You should take appropriate action immediately whenever an instant-on alert is given.
Responding to Alerts
Notice
Description Interpretation
Recommended
Response
FULL ALERT Tone repeats slowly at first, then speeds up rapidly.
Tone sounds one time only.
Tone instantly begins repeating rapidly.
Probably police radar.
Probably a false alarm, but possibly pulsed radar,
VG-2, or Spectre I or IV+ nearby.
Radar, VG-2 or Spectre I or IV+ nearby has been activated suddenly.
Tone repeats slowly as you approach a hill or bridge, then speeds up sharply as you reach it.
Probably police radar beyond the hill or bridge.
Probably a false alarm.
Tone repeats slowly for a short period.
Any type of laser alert.
Laser alerts are never false alarms.
Any Safety Alert.
You are nearing an emergency vehicle, railroad crossing, or road hazard
(construction, accident, etc.).
Exercise caution
FULL ALERT
FULL ALERT
Exercise caution
FULL ALERT
Exercise caution
18 English
Understanding Radar and Laser
Your Detector
Intro Operation Customer Warranty
Radar Speed Monitoring Systems
Three band frequencies have been approved by the Federal Communications
Commission (FCC) for use by speed monitoring radar equipment:
Secondary Icons
X band
K band
Ka band
10.525 GHz
24.150 GHz
33.400 – 36.00 GHz
•
Your detector detects signals in all three radar bands, plus Ku band (13.435 GHz),
Notice which is an approved frequency used in parts of Europe and Asia.
VG-2 and Spectre I & IV+
VG-2 and Spectre I & IV+ are radar detector detectors (RDDs) that work by detecting low-level signals emitted by most radar detectors. Your detector does not emit signals that can be spotted by VG-2 and Spectre I RDDs.
However, your detector can be spotted by Spectre IV+ RDDs. Your unit detects signals from these or similar devices and will alert you when such a device is in use near your vehicle.
Safety Alert Traffic Warning System
FCC-approved Safety Alert transmitters emit microwave radar signals that indicate the presence of a safety-related concern. Depending on the frequency of the signal emitted, it can indicate a speeding emergency vehicle or train, or a stationary road hazard.
Because these microwave signals are within the K band frequency, most conventional radar detectors will detect Safety Alert signals as standard
K band radar. Your detector, however, is designed to differentiate between standard K band and Safety Alert signals, and give separate alerts for each.
Safety Alert technology is relatively new. Safety Alert transmitters can be found in limited numbers in all 50 states, but the number is growing.
Depending on your location, you may not receive these alerts regularly and may often encounter emergency vehicles, trains and road hazards without being alerted. As the number of transmitters increases, these alerts will become more common.
When you receive such an alert, please watch for emergency vehicles ahead of you, on cross streets and behind you. If you see an emergency vehicle approaching, please pull over to the right side of the road and allow it to pass.
Nothing Comes Close to a Cobra ® 19
Your Detector
Intro Operation
Understanding Radar and Laser and Maintenance
Customer Warranty
The correct name for the technology that most people refer to as laser is actually LIDAR, which stands for Light Detection and Ranging.
LIDAR operates much like radar. Its signal spreads out like a radar signal, though
Secondary Icons not as widely. Unlike radar, LIDAR must have a clear line of sight to its target vehicle throughout the entire measurement interval. Obstructions such as sign posts, utility poles, tree branches, etc., will prevent valid speed measurement.
Some common questions about LIDAR include:
■
Does weather have any affect on LIDAR?
Notice
Yes. Rain, snow, smoke, fog or airborne dust particles will reduce the effective range of LIDAR and can, if dense enough, prevent its operation.
■
Can LIDAR operate through glass?
Yes. Newer LIDAR guns can obtain readings through most types of glass.
However, the laser pulse also can be received through glass to trigger an alarm by your detector.
■
Can LIDAR operate while in motion?
No. Because LIDAR operates by line of sight, the person using it cannot drive the vehicle, aim and operate the gun all at the same time.
■
Is LIDAR legal to use?
Yes. It is legal in all 50 states.
Maintenance
Maintenance of Your Radar Detector
Your detector is designed and built to give you years of trouble-free performance
• without the need for service. No routine Maintenance is required.
If your unit does not appear to be operating properly, please follow these troubleshooting steps:
■
Make sure the power cord is properly connected.
■
Make sure the socket of your vehicle’s cigarette lighter is clean and free of corrosion.
■
Make sure the power cord’s cigarette lighter adapter is firmly seated in your cigarette lighter.
■
Check the power cord fuse. (Unscrew the ribbed end cap of the cigarette lighter adapter and examine the fuse. If required, replace it with a 2-amp fuse only.)
20 English
Your Detector
Intro Operation
Specifications
Customer Warranty
Band and Frequencies
Band
Secondary Icons
X Band
K Band
Safety Alert
Traffic Warning
System
Notice
Ka Band
Ku Band
VG-2
Spectre I
Spectre IV+
Laser
Frequencies
10.525
24.125
24.070
24.110
± 0.050
± 0.125
± 0.010
± 0.010
24.190
24.230
34.700
13.435
11.500
13.300
± 0.010
± 0.010
± 1.300
± 0.035
± 0.250
± 0.200
Not Disclosed
910 ± 50
GHz
GHz
GHz
GHz
GHz
GHz
GHz
GHz
GHz
GHz nm
•
This radar detector is covered by one or more of the following U.S. patents:
5,497,148; 5,594,432; 5,612,685; 6,078,279; 6,094,148. Additional patents may be listed inside the product or pending.
Nothing Comes Close to a Cobra ® 21
peration
Notice
Warranty
Warranty
Customer Warranty
For Products Purchased in the U.S.A.
Cobra Electronics Corporation warrants that its Cobra 14 Band Radar/Laser
Detectors, and the component parts thereof, will be free of defects in workmanship and materials for a period of one year from the date of first consumer purchase. This warranty may be enforced by the first consumer purchaser, provided that the product is utilized within the U.S.A.
•
Cobra will, without charge, repair or replace, at its option, defective 14 Band
Radar/Laser Detectors, products or component parts upon delivery to the
Cobra Factory Service Department, accompanied by proof of the date of first consumer purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for warranty service, but the return charges will be at Cobra’s expense, if the product is repaired or replaced under warranty.
This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Exclusions: This limited warranty does not apply:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs.
3. If the serial number has been altered, defaced or removed.
4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty.
Cobra shall not be liable for any incidental, consequential or other damages; including, without limitation, damages resulting from loss of use or cost of installation.
Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you.
Intro
Secondary Icons
Product Service
Customer Assistance
Operation Customer Warranty
Assistance
Product Service
For any questions about operating or installing this new Cobra product, or if parts are missing…PLEASE CALL COBRA FIRST…do not return this product to the store. See customer assistance on page A1.
•
If this product should require factory service, please call Cobra first at
773-889-3087 BEFORE sending the product. This will ensure the fastest turnaround time on any repair.
If Cobra asks that the product be sent to its factory, the following must be
Notice furnished to have the product serviced and returned:
1. Send the complete unit, including power cord. (It is not necessary to include the mounting bracket.)
2. For warranty repair, enclose some form of proof-of-purchase, such as a photocopy or carbon copy of a sales receipt. If you send the original receipt, it cannot be returned.
3. Enclose a typed or clearly written description of the problem you are having with your unit, plus the name and address where you want the unit returned.
4. Pack the unit securely to prevent damage during transit. If possible, use the original packing materials.
5. Ship prepaid and insured using a traceable carrier such as United Parcel
Service (UPS), Federal Express or Priority mail with delivery confirmation.
Ship to: Cobra Factory Service, Cobra Electronics Corporation, 6500 West
Cortland Street, Chicago, IL 60707 U.S.A.
6. Please allow three to four weeks before contacting us about the status of your service. Call 773-889-3087 for assistance. If your unit is under warranty, it will either be repaired or replaced upon receipt, depending on the model. If your unit is out of warranty, you will receive a letter informing you of the repair or replacement charge.
22 English Nothing Comes Close to a Cobra ® 23
Intro ry Icons
Optional Accessories
Customer Assistance
Operation Customer Warranty
Assistance
Optional Accessories
You can find quality Cobra products and accessories at your local Cobra dealer, or in the U.S.A., you can order directly from Cobra. See ordering info on page 25.
•
Notice
Straight 12V DC Power Cord
Includes plug and fuse
Item # 420-030-N-001
Windshield Mounting Bracket
Includes suction cups
Item # 545-159-N-001
Coiled 12V DC Power Cord
Includes plug and fuse
Item # 420-026-N-001
24 English
Dual Port Power Adapter
Includes adjustable plug
(up to 90˚) and fuse
Item # CLP-2B
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project