754RFKIT Wireless Alarm Upgrade Kit, 21762
Wireless Alarm
Upgrade Kit
754RFKIT
With Programmable Alert Tones
®
Installation Instructions
Please leave these instructions at the installation site.
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
Contents
1.0
Introduction .............................................................................................. 3
2.0
Installation Procedure ............................................................................. 4
2.1 Install the RF Transmitter Module..................................................... 4
2.2 Select a Location for the Chime Receiver ........................................ 4
2.3 Install the Chime Receiver Batteries ............................................... 4
3.0
Operation and Testing ............................................................................. 5
3.1 Power On Demonstration .................................................................. 5
3.2 Linking the Transmitter & Receiver ................................................... 5
3.3 Changing the Sound Selection ......................................................... 6
3.4 Sound Volume Adjustment................................................................ 6
3.5 Low Battery Indication ...................................................................... 6
3.6 Snooze Function ............................................................................... 6
3.7 Resetting / Erasing Programmed Parameters.................................. 6
3.8 Linking Multiple Transmitter Units to a Single Chime Receiver Unit ..... 7
3.9 Linking Multiple Chime Receiver Units ............................................. 7
4.0
Troubleshooting ....................................................................................... 8
5.0
Technical Specifications ......................................................................... 8
6.0
Warranty ................................................................................................. 9
7.0
Technical Support .................................................................................... 9
8.0
Notes ....................................................................................................... 10
9.0
Product Range ....................................................................................... 12
2 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
1.0 Introduction
Thankyou for purchasing the 754RFKIT
Wireless/Alarm Upgrade Kit.
The upgrade kit is intended to be used in
conjunction with the Clipsal 754 Series
Infrascan Outdoor Motion Sensor product
range only. The unit is a wireless alarm that is
designed to emit an audible alert in response
to movement detected by the motion sensor.
RF Chime
Receiver
Unit
The unit is battery powered and retro-fittable
– no extra wiring is required. Simply plug in
the RF Transmitter, and the portable Chime
Receiver Unit will automatically alert you
to any external activation of the 754 Series
Motion Sensor.
Features:
• Wireless / RF Accessory Kit
RF Transmitter
Module
• Retrofittable Upgrade to suit 754 Series Motion Sensors
• Six User Selectable Alert Tones when PIR Detects Motion
(Including various Chimes, Knock-Knock, Sonar, Barking Dog)
• Snooze Function Incorporated
• 100metre Wireless Transmission Range, 433MHz
• Battery Operated (3xAA Cell, not included)
• Indoor Use Only
Note:
The upgrade kit is intended to be used in conjunction with the Clipsal 754 Series
Infrascan Outdoor Motion Sensor product range only. Please refer to the back
page of this instruction booklet for an overview of models available.
© Clipsal Australia Pty Ltd
3 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
2.0 Installation Procedure
2.1 Install the RF Transmitter Module
1. Isolate power from your 754 Series Outdoor
Motion Sensor.
2. Remove the rubber bung from the underside of
the detector.
3. Insert the RF Transmitter Module into the
connection socket.
4. Turn the mains power back on to the sensor.
5. The unit will then go through the warm-up
sequence and the Transmitter will automatically
begin to transmit a signal.
2.2 Select a Location for the Chime Receiver
RF Transmitter Installation
1. Position the Chime Receiver Unit in the desired location up to 100 metres away
from the RF Transmitter. Take into account the path between the Transmitter and
Receiver – line of sight is not required, however it is important to note that objects
in between may reduce the maximum transmission distance achievable. Metallic
objects shield RF signals and should be avoided.
2. The Chime Receiver can be placed anywhere within the home. It can be used
purely as a free-standing mobile sounder, or it can be fixed in a permanent
position by using the wall mounting bracket supplied.
2.3 Install the Chime Receiver Batteries
1. Unclip the battery compartment on the bottom of the Chime Receiver Unit.
2. Insert 3 x AA batteries (not supplied).
3. Replace the battery compartment cover.
4. Installation is complete!
4 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
3.0 Operation and Testing
3.1 Power on Demonstration
1. When the batteries are first inserted the Chime Receiver Unit will cycle through
the available sounds. (If this does not occur, press and hold down the “TOOL”
button for more than five seconds to reset the the unit.)
Sounds Options:
Ding Dong ➔ Sonar Sound ➔ Knock Knock ➔ Barking Dog ➔ Alarm / Siren
2. You can press one of the buttons at any time to stop the demonstration.
3.2 Linking the Transmitter and Receiver
1. Ensure that the power to the Motion Sensor unit that has the Transmitter fitted to it
is switched ON.
2. Activate the Motion Sensor so that the Transmitter will broadcast a signal.
3. The Chime Receiver should respond with the Ding Dong sound, and the red LED
will blink quickly as indication that the Motion Sensor is communicating with it.
4. Activate the Motion Sensor a few more times to ensure that the Chime Receiver is
responding reliably, and has good RF reception with the Transmitter.
5. You can choose to leave this sound selection (Ding Dong), or change it to a
desired sound by pressing the “NOTE” button to scroll through the available sound
options.
6. At the required sound, press the “TOOL” button for more than 1 second to select
that sound, and exit from Programming Mode. A single “bi” tone will be heard
indicating that the programmed tone has been successfully changed. The unit is
now in Normal Mode and is ready for use.
RF Chime
Receiver Unit
© Clipsal Australia Pty Ltd
5 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
3.3 Changing the Sound Selection
1. Enter Programming Mode by pressing the “TOOL” button for more than one
second. A triple “bi” tone will be heard to indicate that the Chime Receiver is ready
for programming.
2. To alter the selected sound, first activate the RF Transmitter programmed to the
sound you wish to change.
3. When the Chime Receiver sounds, press the “NOTE” button to scroll through the
available sound options.
4. At the required sound, press the “TOOL” button for more than 1 second to select
that sound, and exit from Programming Mode. A single “bi” tone will be heard
indicating that the programmed tone has been successfully changed. The unit is
now in Normal Mode and is ready for use.
3.4 Sound Volume Adjustment
1. While in Normal Mode, you can adjust the volume by pressing the “NOTE” button.
2. The Chime Receiver will play the currently selected sound, and scroll through 4
volume levels plus one “No Sound” option. The No Sound option is indicated by
the red LED blinking upon activation.
3.5 Low Battery Indication
1. When the battery power is low, every time the Chime Receiver sounds, the sound
will be followed with two “bi” tones and the red LED will blink at a low rate.
2. Replace the batteries as explained in section 2.3.
3.6 Snooze Function
1. The Chime Receiver incorporates a “Snooze” Mode, which is designed to mute
the unit for a period of one hour.
2. Press and hold the “NOTE” button for more than one second and a “snooze”
sound will be heard.
3. Within this one hour period, the Chime Receiver will not respond to the RF
Transmitter, and will not make any sounds.
4. Press any button on the Chime Receiver to cancel Snooze Mode and resume
Normal operation.
3.7 Resetting / Erasing Programmed Parameters
To reset the Chime Receiver and erase all memorized RF Transmitters, just press and
hold the “TOOL” button for more than 5 seconds until the Ding Dong sound and further
sounds are played. Once all tones have played, all Transmitter links to that Receiver
have been erased.
6 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
3.8 Linking Multiple Transmitter Units to a Single Chime Receiver Unit
Each Chime Receiver is capable of responding to multiple Transmitter Modules. This
is useful if you have a number of Motion Sensors throughout the installation, and
require a single Chime Unit to alert the occupant of movement. For example, you can
have a Motion Sensor at the front door and another at the back door, both of which
communicate with a single Chime Receiver.
The Chime Receiver has a default sequence for additional Transmitters linked to it:
Transmitters Linked
1st
Ding Dong
2nd
Sonar Sound
3rd
Knock Knock
4th
Barking Dog
5th
Barking Dog
6th
Barking Dog
A maximum of SIX RF Transmitters can be linked to each Chime Receiver.
To link additional RF Transmitter units to the Chime Receiver, follow the procedure
described below. Be sure to activate only ONE Transmitter at a time. If necessary,
switch power to other 754 Series Motion Sensors OFF whilst programming.
1. Reset the Chime Receiver by holding down the “TOOL” button until the Chime
Receiver begins to scroll through the five available sounds.
2. Activate the motion sensor one at a time to send a signal to the Chime Receiver.
3. The Chime Receiver should pick up the signal from each motion sensor and
activate one of the five sounds, and the red LED should blink quickly to indicate
the RF Transmitter is communicating with the Chime Receiver.
4. Press the “TOOL” button (until a single audible beep is heard) to lock in the
received signals, exit program mode and return to normal mode.
5. Programming of the Chime Receiver is now complete.
3.9 Linking Multiple Chime Receiver Units
Multiple Chime Receiver units can be programmed to respond to each Transmitter.
This might be useful in a larger house, where you may not be able to hear the
Receiver tone from the other end of the house.
To link another Chime Receiver, repeat the steps, 1 to 5 above, until all Transmitters
and Receivers have been linked as required.
© Clipsal Australia Pty Ltd
7 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
4.0 Troubleshooting
PROBLEM
SOLUTION
Chime does not activate
Ensure the batteries are fitted correctly.
Cannot program chime
Check that the transmitter unit has power and the
sensor has been activated.
Ensure the RF transmitter is correctly and
securely fitted in the light unit.
Following the instructions in Section 3.7, reset
the Chime Receiver by deleting all programing
and follow the steps through again.
PIR sensor did not
operate at all
Refer to the Troubleshooting Guide provided with
your Clipsal 754 Series Motion Sensor.
5.0 Technical Specifications
RF Transmitter Power Supply
3.3V d.c. Transmitter
Module Mode
AM O.O.K (ON.OFF.KEY)
Maximum Switchable Load
N/A
Transmission Frequency
433.92 MHz
Tramsmitter Max Power
2dBm
Transmission Range
Up to 100m (varies with surrounding structures)
RF Chime Unit Power Supply
4.5V d.c. (3 x ‘AA’ Batteries)
Reciever Frequency
433.92 MHz
Specifications Typical 25°C
No User Servicable Parts Inside
This Product is Recommended for INDOOR USE ONLY
8 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
6.0 Warranty
1. The benefits conferred herein are in addition to, and in no way shall be deemed to
derogate; either expressly or by implication, any or all other rights and remedies in
respect to the Clipsal Product, which the consumer has under the Commonwealth
Trade Practices Act or any other similar State or Territory Laws.
2. The warrantor is Clipsal Australia Pty Ltd of 33-37 Port Wakefield Road, Gepps
Cross, South Australia 5094. Telephone (08) 8161 0511. With registered offices in
all Australian States.
3. This Clipsal Product is guaranteed against faulty workmanship and materials for
a period of two (2) years from the date of installation. Warranty excludes any user
replaceable parts.
4. Clipsal Australia Pty Ltd reserves the right, at its discretion, to either repair free of
parts and labour charges, replace or offer refund in respect to any article found to
be faulty due to materials, parts or workmanship.
5. This warranty is expressly subject to the Clipsal Product being installed, wired,
tested, operated and used in accordance with the manufacturer’s instructions.
6. All costs of a claim shall be met by Clipsal Australia Pty Ltd, however should the
product that is the subject of the claim be found to be in good working order all
such costs shall be met by the claimant.
7. When making a claim the consumer shall forward the Clipsal Product to the
nearest office of Clipsal Australia Pty Ltd with adequate particulars of the defect
within 28 days of the fault occurring. The product should be returned securely
packed, complete with details of the date and place of purchase, description of
load, and circumstances of malfunction.
7.0 Technical Support
For all technical enquiries and assistance please contact our
National Customer Care Enquiries Hotline
Tel 1300 2025 25
Fax 1300 2025 56
(Call cost 25c, number valid within Australia only)
© Clipsal Australia Pty Ltd
9 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
8.0 Notes
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
10 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
© Clipsal Australia Pty Ltd
11 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
9.0 Product Range
The following products are also available in the 754 Series:
754HL1/140/150
150W Security Floodlight
140° Passive Infrared Outdoor Motion Detector
Complete with 150W R7s Linear Halogen Floodlight
754HS1/140/60
60W Security Spotlight
140° Passive Infrared Outdoor Motion Detector
Complete with Single 60W G9 High Efficiency Halogen Spotlight
754HS2/140/60
60W Security Twinspot
140° Passive Infrared Outdoor Motion Detector
Complete with Twin 60W G9 High Efficiency Halogen Spotlights
754HF1/180/150
150W Security Floodlight
180° Passive Infrared Outdoor Motion Detector
Complete with 150W R7s Linear Halogen Floodlight
754HF1/180/300
300W Security Floodlight
180° Passive Infrared Outdoor Motion Detector
Complete with 300W R7s Linear Halogen Floodlight
754HB1/180/60
60W Security Spotlight
180° Passive Infrared Outdoor Motion Detector
Complete with Single 60W G9 High Efficiency Halogen Spotlight
754HB2/180/60
60W Security Twinspot
180° Passive Infrared Outdoor Motion Detector
Complete with Twin 60W G9 High Efficiency Halogen Spotlights
Clipsal Australia Pty Ltd
clipsal.com
A member of Schneider Electric
Contact us: clipsal.com/feedback
National Customer Care Enquiries:
Tel 1300 2025 25
Fax 1300 2025 56
Clipsal Australia Pty Ltd reserves the right to change specifications, modify designs and discontinue
items without incurring obligation and whilst every effort is made to ensure that descriptions,
specifications and other information in this catalogue are correct, no warranty is given in respect thereof
and the company shall not be liable for any error therein.
© Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of
Clipsal Australia Pty Ltd unless otherwise noted.
F2109/02
CLIPCOM 21762 June 2010
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising