RSL-2701S

RSL-2701S
OWNER'S MANUAL
RSL-2701U(for CANADA MODEL)
RSL-2701S (for USA MODEL )
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Supporton
tab
www.royalsovereign.com
Royal Sovereign International Inc.
www.royalsovereign.com
TABLE OF CONTENTS
TOpIC
pAgE
1. Introduction ..................................................................................................................................................... 3
2. Package Contents ............................................................................................................................................. 3
3. Safety Precautions............................................................................................................................................ 4
4. Parts ................................................................................................................................................................. 5
5. Control Panel .................................................................................................................................................... 6
6. Features Guide.................................................................................................................................................. 8
7. Film Loading and Threading ............................................................................................................................ 9
8. Operation Instructions.................................................................................................................................... 13
9. Maintenance ................................................................................................................................................. 13
10. Trouble Shooting Guide ................................................................................................................................ 14
11.Specification .................................................................................................................................................. 15
12.Warranty ........................................................................................................................................................ 16
2
TABLE TOp LAMINATOR
1. INTRODUCTION
Thank you for purchasing the Table Top Laminator. It has been designed and manufactured to provide years of
continuous service. For high quality lamination, please read this instruction manual thoroughly. This manual will provide
you with complete operating and maintenance information.
2. pACkAgE CONTENTS
Film leader board
Manual
Core 4EA
3
Fuse
Core bolt 4EA
Dust cover
Sample roll film 2EA
3. SAFETy pRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury.
please read the instructions carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers have pinch points that can trap body parts
or
clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing.
8. Keep out of reach of children.
9. Only authorized maintenance and service technicians should make repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness for the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when hot.
Do not place any foreign obects inside the laminator.
13. Do not cover the surface of the machine until the machine has completely cooled.
14. You can laminate by single film when the switch in the left cover is “O”.
(Insure the machine drastically cold, press the button in the left cover be “ O ”, then you can laminate by single
side. It is a damage for the paper to laminate by single side while the rollers up and low are heating all together.)
- Model applies RSL-2701S only for USA.
4
TABLE TOp LAMINATOR
4. pARTS
10
1. Upper Film
2. Lower Film
3. Idle Bar
4. Hot Rollers
5. Feed Table
6. Paper Guide
7. Control Panel
8. Tension Knob
9. Power Switch
*10. (2701S model only) Single/Double Laminating Switch “O” (on) “I” (off).
* For Single-side Laminating.
5
5. CONTROL pANEL
270 ~310 ˚F
Film Application Temperature
270 ~310 ˚F
230 ~270 ˚F
Film Application Temperature
230 ~270 ˚F
210 ~230 ˚F
Film Application Temperature
210~230 ˚F
270-310 F
230-270 F
210-230 F
UP
Increase roller speed
(1~10 speed settings)
DOWN
Reduce roller speed
(1~10 speed settings)
REVERSE
Reverse the rollers to undo jams and correct
misfed documents
Run and stop the machine
RUN/STOP
RSL-2701U
6
TABLE TOp LAMINATOR
5 mil
125 mic
2 - 4 mil
50-100 mic
1 - 1.5 mil
125mic
* (100~125mic)
Film Application Thickness
125mic(100~125mic)
50~100mic
* (50~75mic)
Film Application Thickness
50~100mic(50~75mic)
25~38mic
* (25~38mic)
Film Application Thickness
25~38mic(25~38mic)
25-38 mic
UP
Reduce roller speed
(1~10 speed settings)
DOWN
Increase roller speed
(1~10 speed settings)
REVERSE
Reverse the rollers to undo jams and correct
misfed documents
RUN/STOP
Run and stop the machine
* For Single side Laminating.
RSL-2701S
7
6. FEATURES gUIDE
Power Switch 1
Located on the rear of the machine. “I” (on) “0” (off). (Fig. 2)
Cross Cutter 2
Used to cut off the laminated web. (Fig. 2)
Feed Guide 3
The feed guide permits alignment of the item(s) to be laminated.
To position the adjustable guide, loosen the knob, slide it to the
desired position and tighten the knob to secure the feed guide in
place. (Fig. 3)
Figure 2
Safety Cover 4
Cover + Protect the hot rollers.
NOTE: If the safety cover is opened, this rollers stop turning.
Figure 3
Film Shaft and Locking Core Adapter 5
The film shaft holds the film supply on the machine. The locking
core holds and locks the film on the shaft to prevent shifting. (Fig.
4)
5
Film Tension Adjustment 6
Allows the operator to increase or decrease roll film tension. To
increase the tension turn the knob clockwise and to decrease
tension turn the knob counterclockwise. (Fig. 5)
NOTE: - Excess tension on the top roll feed will cause upward
curl.
- Excess tension on the botton roll feed will cause
downward
curl.
- Tension should be adjusted until the laminated materials
exit flat.
Figure 4
6
Figure 5
8
TABLE TOp LAMINATOR
7. FILM LOADINg & ThREADINg
Figure 6
1. Slightly slide the upper film shaft to the right and pull it out from
the machine. (Fig. 7)
Figure 7
2. Take both lock core adapters off from the shaft. (Fig. 8)
Figure 8
9
3. Insert one of the core adapters into the right end of the film
core. For film with poly-in (adhesive side is inside the web), make
sure the adhesive side is facing upward. (Fig. 9)
Figure 9
4. Insert the film shaft into the roll of film from the right side with
the copper end last.
Align and insert the core adapter on the left end of the film
core. (Fig. 10)
Figure 10
5. Center the film on the shaft and lock it in place with the
locking core adapters. (Fig. 11)
Figure 11
6. Carefully return the film shaft back into place. (Fig. 12)
Figure 12
10
TABLE TOp LAMINATOR
LOADINg LOWER ROLL FILM
1. Repeat steps 1-5 to load the lower roll film.
2. Once the upper and lower film is on the shaft, pull the film from the top and roll down to the bottom roll to make
certain that the film is aligned properly. Then tighten the lower locking core screws.
NOTE: If the film is not aligned properly exposed adhesive will adhere to the rollers and may cause the film to jam.
FILM ThREADINg / WEBBINg
1. Set the temperature and speed according to the Recommended
Temperature and Speed section.
2. Remove the Front Table.
3. Pull down the upper film over the Safety Cover to the lower film; align
and center the lower film to upper film. (Picture 1)
Picture 1
4. Rewind the upper film until the film aligns with the Safety Cover.
5. Thread the film over the Upper Idle Bar and underneath the Safety
Cover and pull down until it drapes over both upper and lower hot
rollers. (picture 2)
6. Carefully pull up the laminate from the lower roll up and drape it over
top of the upper film (over the top hot roller). (picture 3)
Picture 2
7. Reinstall the Front Table and close the Safety Cover.
8. Insert and push the leader board into the hot rollers and press the
Run button. (picture 4)
9. Press the Stop button when the leader board has completely exited
the rear of the laminator.
10. Use the Cross-Cutter to remove the leader board.
Picture 3
11. Trim any excess film off of the leader board. The leader board can
be re-used.
Picture 4
11
LAMINATINg SINgLE SIDED (RSL-2701S USA Model only)
Press the switch into the location “SINGLE ”.
Figure 13
12
TABLE TOp LAMINATOR
8. OpERATION INSTRUCTIONS
1. Turn the laminator ON (I) located on the rear of the machine. (Fig. 2)
2. Choose appropriate laminating temperature and speed. (Fig. 1)
3. Do not begin laminating until the blinking light is steady (approximately 8 minutes).
4. Position the item to be laminated on the feed table.
5. Press the RUN button. The rollers will begin to turn, and feed the item into the machine.
6. Insure the machine drastically cold, press the button in the left cover be “ O ”,then you can laminate by upper
roller for single laminating.(It is a damage for the paper to laminate by single side while the rollers up and low are
heating all together.)
- Model applies RSL-2701S only for USA.
7. The first paper is bad while OPP film laminating, please use a test paper first and then the second paper must
keep the distance less than 15mm form the front one.
- Model applies RSL-2701S only for USA.
8. Stop the laminator when all of the items have completely exited the rear of the machine.
9. Adjust top + botton roll feed tension until lamination is flat.
(See film tension adjustment page 8.)
NOTE: Stand by mode and auto power off mode
- Stand by mode: If no activity is made within 30 minutes after each use the machine will automatically switch
into stand by mode. (In stand-by mode the temperature will decrease to 80~90°C and the three
temperature setting indicators will blink).
- Auto power off mode: If the machine is in stand by mode and no activity is made for 60 minutes the
machine will automatically power off.
- If any activity is made while in stand by or auto power off mode the machine will return to it’s previous
stage.
9. MAINTENANCE
1. Do not apply any cleaning fluids to the rollers certain fluids may cause damage.
2. Do not clean rollers with sharp or pointed objects.
3. Use a crepe rubber cleaning block to remove adhesive from rollers. Works best when rollers are hot.
4. Use a damp cloth with water to clean the body of the machine.
5. Store machine in a dry clean area.
13
10.TROUBLE ShOOTINg gUIDE
Symptom
Cause
1.Safety cover is opened
Rollers do not operate after the RUN/
STOP button is pressed
2. Power cord is not plugged in
3. Front table is not on properly
4. Machine is not turned on
Roller is not heating
Call your authorized dealer
1. Film tension is unbalanced.
Poor Lamination
2. Lower idler bar is not located in
proper position
possible Solution
1. Check safety cover is
properlyclosed
2. Plug in the power cord
3. Check installed properly
4. Turn the machine on
Call your authorized dealer
1. Adjust film tension
2. Push idler bar in proper position
3. Follow manufacturers
recommended temperature and
3.Wrong temperature / speed setting
speed
14
TABLE TOp LAMINATOR
11. SpECIFICATIONS
MODEL
RSL-2701U
RSL-2701S
Power supply
AC120V 60Hz
Power consunmption
1450W
AC100V 60Hz
AC220~240V
50/60Hz
380mm
25~250mic /1~10mil
25~125mic/1~5mil
2.5m/min
3m/min
Ready time
10min
Heating method
Hot Roller
Driving motor
DC geared motor
Temperature control
Digital(micom)
Speed control
Digital(10steps)
Transport type
4Roller
Cross cutter
Yes
Single
No
RSL-380S
AC 220~240V 50/60Hz
685mm
Max laminating speed
Hot
lamination
RSL-2701S
1500W
Max laminating width
Film thickness
RSL-2701
Yes
No
Double
Yes
Yes
Yes
Reverse
Yes
Dimensions(w×d×h)
920×520×320mm
550×520×320mm
Unit weight
50kg
30kg
15
11. WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a
period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are
warranted for Six (6) months. This warranty is extended only to the original purchaser. This warranty is the only
warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign’s sole and
exclusive liability and the customer’s sole and exclusive remedy under this warranty shall be, at Royal Sovereign’s
option, to repair or replace any such defective part or product. These remedies are only available if Royal
Sovereign’s examination of the product discloses to Royal Sovereign’s satisfaction that such defects actually exist
and were not caused by misuse, neglect, attempt to repair, unauthorized alternation or modification, incorrect line
voltage, fire, accident, flood or other hazard.
All warranty claims must be filed through the authorized Royal Sovereign dealer or reseller through which the
equipment was originally purchased. Model, serial number and date of delivery are required for all claims.
The warranty made herein is in lieu of all other warranties, expressed or implied, including any warranty or
merchantability or fitness for a particular purpose. Royal Sovereign will not be liable for personal damage or personal
injury (unless primarily caused by its negligence), loss of profit, or other incidental or consequential damages arising
out of the use or inability to use this equipment.
LIMITED WARRANT
Y
This warranty specifically does not cover damage to laminating rollers caused by knives, razor blades, or any sharp
objects or abrasives, or failure caused by adhesives, or damage caused by lifting, tilting or improper use of the
machine. Warranty repair or replacement by Royal Sovereign or its authorized Reseller(s) does not extend the
warranty beyond the initial one year period from the date of installation. Unauthorized customer alterations will void
this warranty.
www.cigraph.com.co
Calle 143 No 46 - 64
(57)+1 742 42 23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising