Illustra Pro PTZ Recessed Indoor Flush Mount Housing QSG

Illustra Pro PTZ Recessed Indoor Flush Mount Housing QSG
Quick Reference Guide
Illustra Pro PTZ Recessed Indoor Flush Mount Housing
8200-1199-04 A0
Notice
The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products.
All specifications are therefore subject to change without notice.
Copyright
Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any
electronic medium or machine-readable form, in whole or in part, without prior written consent of Tyco Security Products © 2015 and
its Respective Companies. All Rights Reserved.
Tyco Security Products
6600 Congress Avenue
Boca Raton, FL 33487 U.S.A.
Customer Service
Thank you for using Tyco Security Products. We support our products through an extensive worldwide network of dealers. The dealer
through whom you originally purchased this product is your point of contact if you need service or support. Our dealers are
empowered to provide the very best in customer service and support. Dealers should contact Tyco Security Products at (800) 5076268 or (561) 912-6259 or on the Web at www.illustracameras.com.
Trademarks
The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any
misuse of the trademarks is strictly prohibited and Tyco Security Products will aggressively enforce its intellectual property rights to
the fullest extent of the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco Security
Products are the property of their respective owners, and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products
include all features. Availability varies by region; contact your sales representative.
License Information
Your use of this product is governed by certain terms and conditions. Please see the detailed license information at the end of this
manual.
ii
Table of Contents
Illustra Pro PTZ Recessed Indoor Flush Mount Housing
To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
Installing the Illustra Pro PTZ Recessed Indoor Flush Mount Housing. . . . . . . . . . . . 2
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Mechanical Details and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ii-i
Table of Contents
ii-ii
Quick Reference Guide
Illustra Pro PTZ Recessed Indoor Flush Mount
Housing
To the Installer
This guide assumes that the indoor mounting structure to which the housing is attached is in place
and that data and power cables have been pulled to the installation site.
1. The installation shall be performed by a qualified person in accordance to all local regulations.
2. External power source must be a NEC class 2 / Certified Limited Power Source (LPS)
What’s in the box
Standard Items
• Recessed Indoor Flush Mount Housing including Camera Mounting Spider
• Quick Reference Guide
• Safety Wire
• Cable Tie
• Cutout Template
Mounting Requirements
• Height above ceiling: 170mm (6.7in)
• Diameter: 192mm (7.5in)
• Structural members: Verify that ceiling members can support the camera dome and mounting
structure, if used.
• Weight Fully Assembled: 3.5Kg
Tools Required
• 6.6mm (1/4in) fixed-handle nut driver for Torx bit
• Wire cutters and strippers
• 2.5mm (0.1in) slotted screwdriver
• Power Drill
1
Illustra Pro PTZ Recessed Indoor Flush Mount Housing Quick Reference Guide
Installing the Illustra Pro PTZ Recessed Indoor Flush Mount
Housing
The following describes the installation procedure for the Illustra Pro PTZ Recessed Indoor Flush
Mount Housing.
Step
Action
1
Remove the recessed indoor flush mount unit from the packaging.
2
Using the template supplied, as illustrated in Figure 1:
a
Determine the direction of the cable routing and orientate the template.
Note
The housing has a conduit adapter, this will determine the orientation of the
template.
b
Drill two 20mm diameter holes in the positions highlighted on the template. See
diagram below.
c
Use one of the drilled holes for the saw entry and cut around the profile.
Figure 1
Cut Line
Lo
c
of
on
i
t
a
n
co
it
du
ap
ad
ter
Drill 20mm
hole here
Drill 20mm
hole here
2
i625PTZ Indoor Recessed Housing
Illustra Pro PTZ Recessed Indoor Flush Mount Housing
3
Adjust the two “swing out” mounting clips for the ceiling thickness as seen in Figure 2.
Figure 2
4
Using the two safety wires, attach the housing to a strong structural ceiling member as
follows:
a
Find a strong structural member capable of supporting the dome. Wrap one end of
the wire around this member and twist the wire around itself four times to secure.
Repeat for the second wire.
b
Run the other end of the wire through the bracket on the side of the housing. Twist
the wire around itself four times to secure. Reference Figure 3.
Figure 3
c
Ensure the wire is taut!
Repeat for the second wire.
Keep the wire as taut as possible. Do not secure to any component of a fire control
system.
3
Illustra Pro PTZ Recessed Indoor Flush Mount Housing Quick Reference Guide
5
Secure the housing to the ceiling.
a
Insert housing in the ceiling cutout. Reference Figure 4.
Figure 4
b
Angle the housing as necessary to ease insertion into the cutout. Ensure that the
orientation of the housing is correct with reference to the conduit adapter.
c
When in place, turn the two locking screws clockwise to seat the “swing out”
mounting clips tightly against the ceiling to secure as seen in Figure 5.
Figure 5
6
Remove the camera mounting spider from the housing.
The safety lanyard will keep the camera mounting spider attached to the housing and
should not be removed.
a
4
Rotate the camera mounting spider anti-clockwise to release it from the screws on
the housing flange.
i625PTZ Indoor Recessed Housing
Illustra Pro PTZ Recessed Indoor Flush Mount Housing
b
Pull the camera mounting spider down to remove it from the outdoor recessed
housing as seen in Figure 6.
Figure 6
7
To aid installation the camera mounting spider can be connected to the camera housing in
the parked position.
a
Attach the keyhole cutout on the angled leg of the camera mounting spider to one of
the screws on the housing flange as seen in Figure 7.
Figure 7
5
Illustra Pro PTZ Recessed Indoor Flush Mount Housing Quick Reference Guide
8
Route site cables into the housing. Reference Figure 8.
The Audio Output and Microphone cables shall be shielded and shall not be longer than
30m.
a
Route power and data cables through the adapter.
Note
Electrical conduit and conduit adaptor are not supplied with the housing.
Figure 8
9
Terminate the power and data wires using the provided connectors.
The pin out details for power, alarms and audio are as follows:
Power AC/DC
Pin#
6
3 Wire DC Supply
1
24Vac/24Vdc
2
-
3
24Vac/Vdc
i625PTZ Indoor Recessed Housing
Illustra Pro PTZ Recessed Indoor Flush Mount Housing
Alarm and Audio (Available on Feature PLus models) only)
Pin#
10
Designation
Pin#
Designation
1
Relay NO (Normally Open)
11
Alarm IN #1 (Active Low)
2
Relay C (Common)
12
GND
3
Relay NC (Normally Closed)
13
Alarm IN #2 (Active Low)
4
GND
14
Alarm IN #3 (Active Low)
5
-
15
MIC BIAS (4.5V 2mA)
6
-
16
Alarm IN #4 (Active Low)
7
GND
17
MIC Input
8
GND
18
Audio Output
9
-
19
Audio GND*
10
-
20
Audio GND*
If required, install a microSD card into the dome memory card slot:
Note
The microSD card is an optional accessory and is not supplied with the dome. The
maximum size of microSD card that can be used with the dome is 32GB. Contact
your Tyco Security Products representative for further information.
a
Align the microSD card with the memory card slot as shown, the gold-colored
contacts should face towards the camera lens as seen in Figure 9.
b
Push the microSD card into the memory card slot until it locks into position.
c
To remove the microSD card push the card gently until it disengages from the dome.
d
Remove the microSD card.
Figure 9
7
Illustra Pro PTZ Recessed Indoor Flush Mount Housing Quick Reference Guide
11
Attach the camera mounting spider to the Illustra Pro PTZ dome as seen in Figure 10.
a
Insert the dome into the camera mounting spider and align with the corresponding
boss features on the dome base.As a guide, use the straight edge of the camera
mounting spider to align with the straight edge of the camera base.
Figure 10
b
Secure the dome to the camera mounting spider by sequentially tightening the three
M4 captive screws as seen in Figure 11.
Hereafter the camera mounting spider and dome will be referred to as the dome
assembly.
Figure 11
12
8
Connect the cables to the Illustra Pro PTZ dome.
i625PTZ Indoor Recessed Housing
Illustra Pro PTZ Recessed Indoor Flush Mount Housing
a
Attach the Price+ connector first followed by Ethernet and Power.
b
Secure cables to the cable tie holder on the dome assembly using a cable tie as seen
in Figure 12.
Figure 12
13
Insert the dome assembly into the housing:
a
Align the arrow on the dome assembly with the arrow on the housing flange as seen
in Figure 13.
Figure 13
b
Insert the dome assembly into the housing.
Ensure that the three screws on the housing flange align with the corresponding
9
Illustra Pro PTZ Recessed Indoor Flush Mount Housing Quick Reference Guide
keyhole cutouts on the dome assembly as seen in Figure 14.
Figure 14
c
Maintain upward pressure and rotate the dome assembly clockwise to lock into
position.
Ensure that the screws on the housing flange are fully engaged before removing your
hands from the dome assembly.
10
i625PTZ Indoor Recessed Housing
Illustra Pro PTZ Recessed Indoor Flush Mount Housing
d
Secure the camera mounting spider to the housing by tightening the three screws on
the housing flange as seen in Figure 15.
Figure 15
14
Remove the bubble assembly from the package and ensure that the bubble is clean and
free of debris.
15
Attach bubble assembly:
a
Attach the lanyard on the housing to the trim ring on the bubble assembly as shown
in Figure 16.
Figure 16
b
Center the trim ring over the housing and align its locking tabs with the mating tabs in
the housing.
c
Offer up the trim ring to the housing ensuring that the lanyard collapses as seen in
Figure 17.
11
Illustra Pro PTZ Recessed Indoor Flush Mount Housing Quick Reference Guide
Figure 17
d
Rotate the trim ring clockwise until it catches the tabs and stops. The bubble adaptor
is now secure.
Ensure that all four tabs are engaged.
12
i625PTZ Indoor Recessed Housing
Illustra Pro PTZ Recessed Indoor Flush Mount Housing
Specifications
PoE
• 802.3at PoE+ 25.5W max
Electrical (combined dome and housing)
• Input Voltage 22 to 30Vac, 50/60 Hz
NEC Class 2 / Certified Limited Power Source
Maximum operation current 1.4A. RMS
Environmental
• Operating Temperature –10°C to 50°C
(14°F to 122°F)
• Relative Humidity 0 to 95% non-condensing
• Storage Temperature –10°C to 50°C
(14°F to 122°F)
Mechanical Details and Dimensions
Dimensions are in mm
Weight Fully Assembled: 3.5Kg (7.7lbs)
Housing: 1.35Kg (2.98 lbs)
Bubble/Trim Ring Assembly: 0.3kg (0.66lbs)
Camera: 1.85kg (4.09lbs)
13
Illustra Pro PTZ Recessed Indoor Flush Mount Housing Quick Reference Guide
14
i625PTZ Indoor Recessed Housing
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising