Animal Weighing - Scientific Industries

Animal Weighing - Scientific Industries
AGC Series: Quick Reference Guide
Torbal Laboratory Balances
Animal Weighing
Before using this reference guide, enable and configure Animal Weighing by following the steps listed in Chapter 7.1.3
of the Instruction Manual. To enter the Animal Weighing mode press the “Function” key, and select the function by
pressing the “T” key while “Animal” is displayed.
1. Place a container on the pan and tare it by pressing the “T’ key.
2. Place the animal into the container.
Automatic and Semi Automatic
modes
Animal Weighing will begin
automatically.
Manual mode
Press the ”Function” key to initialize
Animal Weighing.
3. The scale will count down a time interval.
1
AGC Series: Quick Reference Guide
4. After the time interval has elapsed the result will be displayed.
5. The animal can be removed from the pan
Automatic mode: Result will be automatically cleared; the scale will perform
an automatic tare.
Manual and Semi Automatic modes: To clear the result, press the “C” key. After clearing the function press “T”
to tare.
To Clear
To Tare
For a detailed description of this feature please turn to Chapter 8(A) of the instruction manual.
For technical questions or assistance please call toll free: 1-866-473-6900
Fulcrum Inc.
23 Carol Street.
Clifton, NJ 07014
(973) 473-6900
http://www.torbal.com
2
AGC Series: Quick Reference Guide
Check Weighing
Before using this reference guide, enable and configure Check Weighing by following the steps listed in Chapter 7.1.3
of the Instruction Manual. To enter the Check Weighing mode press the “Function” key, and select the function by
pressing the “T” key while “Check” is displayed.
1.
Upon entering the check weighing function, the UNDER limit is displayed. If an under limit has already been set
and no change is necessary, press “T” (YES) to accept and continue. If you wish to change the setting, press the
“0 (NO)” key. To set a new weight limit use the table below.
1
AGC Series: Quick Reference Guide
2.
If an over limit has already been set and no change is necessary, press “T” (YES) to accept and continue. If you
wish to change the setting, press the “0 (NO)” key. To set a new weight limit use the table shown in step1.
To Accept
To Change
3. Place a container on the pan and press “T” to tare.
4. To perform check weighing place your object on the pan to check whether the weight of the object falls within
the designated range. The weight of the object and the result will be displayed sequentially.
For a detailed description of this feature please turn to Chapter 8(C) of the instruction manual.
For technical questions or assistance please call toll free: 1-866-473-6900
Fulcrum Inc.
23 Carol Street.
Clifton, NJ 07014
(973) 473-6900
http://www.torbal.com
2
AGC Series: Quick Reference Guide
Display Hold
Before using this reference guide, enable and configure Display Hold by following the steps listed in Chapter 7.1.3 of the
Instruction Manual. To enter the Display Hold mode press the “Function” key, and select the function by pressing the
“T” key while “Display” is displayed.
1. Place a container on the pan and tare it by pressing the “T’ key.
2. Place the weight in the container located on the pan.
Automatic and Semi-Automatic
Manual
Display hold is initialized by pressing the “Function”
key. Once the weight is stable press “Function” to
lock the result on the display.
The scale will automatically lock the weighing result
on the display as soon as it stabilizes.
1
AGC Series: Quick Reference Guide
3. Remove the weight from the pan.
Automatic
Semi-Automatic and Manual
The result will be automatically cleared after the
weight is removed from the pan. The scale will
perform an automatic tare and prepare for the next
weighing.
To clear the weighing result press the “C” key. After
the result has been cleared the scale must be tared.
To tare the scale press the “T” key.
To Clear
To Tare
For a detailed description of this feature please turn to Chapter 8(D) of the instruction manual.
For technical questions or assistance please call toll free: 1-866-473-6900
Fulcrum Inc.
23 Carol Street.
Clifton, NJ 07014
(973) 473-6900
http://www.torbal.com
2
AGC Series: Quick Reference Guide
Parts Counting
Before using this reference guide, enable and configure Parts Counting by following the steps listed in Chapter 7.1.3 of
the Instruction Manual. To enter the Parts Counting mode press the “Function” key, and select the function by pressing
the “T” key while “Parts” is displayed.
1. Place a container on the pan and tare it by pressing the “T’ key.
2. Confirm the sample size by pressing the “T (Yes)” key.
3. Manually count out the sample and place it in the container located on the pan.
1
AGC Series: Quick Reference Guide
4. Press the “T (YES)” key to confirm and accept the sample weight.
5. Begin to fill the remainder of the pieces.
For a detailed description of this feature please turn to Chapter 8(B) of the instruction manual.
For technical questions or assistance please call toll free: 1-866-473-6900
Fulcrum Inc.
23 Carol Street.
Clifton, NJ 07014
(973) 473-6900
http://www.torbal.com
2
AGC Series: Quick Reference Guide
Percent Weighing %
Before using this reference guide, enable and configure Percent Weighing by following the steps listed in Chapter 7.1.3
of the Instruction Manual. To enter the Percent Weighing mode press the “Function” key, and select the function by
pressing the “T” key while “Percent” is displayed.
1. Place a container on the pan and tare it by pressing the “T” key.
2.
The scale will display the weight of a previously stored sample. To accept the current sample setting, press the
“T” (YES) key and skip to step 5. To assign a new sample, press the 0(NO) key.
3. Place the sample on the pan.
1
AGC Series: Quick Reference Guide
4. The weight of the sample will be displayed. Press the “T (YES)” key to confirm and accept the sample weight.
5. Remove the sample and place the object on the pan. The scale will express the weight of the object as a
percentage of the stored sample.
For a detailed description of this feature please turn to Chapter 8 of the instruction manual.
For technical questions or assistance please call toll free: 1-866-473-6900
Fulcrum Inc.
23 Carol Street.
Clifton, NJ 07014
(973) 473-6900
http://www.torbal.com
2
AGC Series: Quick Reference Guide
Totalizing
Before using this reference guide, enable and configure Totalizing by following the steps listed in Chapter 7.1.3 of the
Instruction Manual. To enter the Totalizing mode press the “Function” key, and select the function by pressing the “T”
key while “Totalize” is displayed.
1. Place a container on the pan and tare it by pressing the “T’ key.
2. Place the first object in the container located on the pan.
Automatic
The weight of the object will be added automatically.
Once the weight stabilizes, the TOTAL indicator will
appear on the display, signaling that the weight has
been added to the grand total
Manual
Once the weight stabilizes and the stability indicator
appears on the display press the “Function” key to add
the weight to the grand total.
Add to Total
With each added weight, the grand total result appears on the display for approximately three seconds. To recall
the grand total at any time, press the “Menu” key.
1
AGC Series: Quick Reference Guide
Recall Total
3. Once a weight of an object has been added to the total, remove the object from the pan or press “T” to tare the
scale.
4. After the scale has been tared, Steps 1 through 3 can be repeated in order to add more weighing results to the
grand total.
5. To clear the grand total and reset the function press the “C” key.
To Clear
To Continue
For a detailed description of this feature please turn to Chapter 8(F) of the instruction manual.
For technical questions or assistance please call toll free: 1-866-473-6900
Fulcrum Inc.
23 Carol Street.
Clifton, NJ 07014
(973) 473-6900
http://www.torbal.com
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising