MASTER dimmer 120 V~ 60 Hz for incandescent lamps 40

MASTER dimmer 120 V~ 60 Hz for incandescent lamps 40
01985.120
MASTER dimmer 120 V~ 60 Hz for incandescent lamps 40-500 W electronic
transformers 40-300 VA, CFL lamps 10-200 W, LED lamps 3-200 W, for LED
electronic power supplies, protection fuse, installation on DIN rails (60715
TH35), occupies 4 modules size 17.5 mm. For nautical scope.
FRONT VIEW
N
S
ON/OFF switch and adjustment with two built-in buttons. MOSFET+TRIAC microprocessor
technology, works in both LE (Leading Edge) and TE (Trailing Edge) modes. MASTER function,
protection fuse. The device receives commands directly from the Busbar and is able to control
the load directly. It can also control up to 3 SLAVE dimmers for DIN rails 01986.120.
N
L
S
A
01985.120
MASTER DIMMER
120 V~ 60 Hz
IMPORTANT: Lamps controllable from a single master or slave dimmer must all be the
same. All controllable loads must be declared DIMMERABLE by the manufacturer. Check
the type of compatible dimmering on the lamp package: LE (Leading Edge) or TE (Trailing
Edge). If it is not specified, the lamp can operate in both modes (chosen at the discretion
of the installer).
Dimmering with Leading Edge mode
L
B
C
D
40-500W LE
40-300W TE
Dimmering with Trailing Edge mode
A: Indicator LED
B: Switching on and increasing brightness
C: Switching off and decreasing brightness
D: LED and configuration button
BUS TP
CONNECTIONS
L
N
01985.120
01986.120
01986.120
MASTER
SLAVE
SLAVE
CHARACTERISTICS.
• Rated supply voltage TP Busbar: 29 V
• Rated supply voltage mains: 120 V~, 60 Hz
• Absorption from TP Busbar: 15 mA
• Dissipated power: 7.8 W
load, L phase, S synchronization, TP Busbar
• Terminals: N neutral,
• Protection fuse type F5AH250V
• Functions that can be accomplished with the dimmer:
- Switching on, off and dimmering
- Changing absolute brightness
- Actuating/saving scenarios
- Enabling "Flash Start" mode for CFL lamps
- "Ramp" operation
- Switch-off delay and warning function
- Phase cutting: LE/TE
• Local controls:
button enables using the local buttons. All messages from the busbar are
Pressing the
ignored.
: ON control
- Briefly pressing the button
: OFF control
- Briefly pressing the button
: Increase brightness
- Pressing and holding down the button
: Decrease brightness
- Pressing and holding down the button
In normal operation (that is when the commands are sent over the bus) pressing the buttons
for the outputs is ignored.
• Protection against short-circuiting when turning on with flashing blow-out indicator.
• Thermal protection with flashing blow-out indicator.
• MASTER-SLAVE function: paying attention not to exceed maximum power controllable by
each dimmer. A MASTER device can have up to 3 SLAVE dimmers (art. 01986.120) for a
maximum total load of 2000 W (VA) corresponding to 500 W/VA max connected to each of
the 4 devices.
• Installation on DIN rails (60715 TH35), occupies 4 modules of 17.5 mm.
Controllable loads
Electronic transformers
for halogen lamps
TE
40 to 500 W
40 to 300 W
10 to 100 W (Max 5 lamps)
10 to 200 W (Max 10 lamps)
3 to 100 W (Max 5 lamps)
3 to 200 W (Max 10 lamps)
L )
40 to 300 W
(Max 5 transformers type
C )
CONFIGURATION.
FOR THE OPERATIONS OF INSTALLATION AND CONFIGURATION, SEE THE BY-ME
SYSTEM INSTRUCTIONS MANUAL ATTACHED TO THE CONTROL PANEL.
• Functional units: 1; the unit can belong to at most 4 different groups.
• Selecting the functional unit (configuration): during group creation, when the control panel
requires pressing the device button:
- It is recommended to configure the device with the load OFF;
- Press the CONF button, the red LED will light up;
- With the red LED on, the control panel will configure the functional unit; at the end of this
operation the red LED will go out.
Viale Vicenza, 14 - 36063 Marostica VI Italy
Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188 - Fax (Export) +39 0424 488 709
www.vimar.com
L
S
01985.120
MASTER DIMMER
120 V~
60 Hz
40-500W LE
40-300W TE
N
L
S
01986.120
SLAVE
DIMMER
N
TE
Flash
LE
Soft
L
S
01986.120
SLAVE
DIMMER
120 V~
60 Hz
40-500W LE
40-300W TE
TE
Flash
LE
Soft
120 V~
60 Hz
40-500W LE
40-300W TE
Bus
Maximum length of cables connecting universal MASTER dimmer and universal SLAVE dimmer: 100 m
Connect at least the minimum load required to the universal master dimmer.
CHANGING FUSE
L
N
N
L
S
S
01985.120
MASTER DIMMER
120V~
OFF
By-me
60Hz
40-500W LE
40-300W TE
CONF.
BUS
1.
2.
INSTALLATION RULES.
LE
40 to 300 W
(Max 3 transformers type
N
Installation should be carried out in compliance with the current regulations regarding the installation of electrical systems in the country where the products are installed.
• It should be used in places at a temperature of between -5°C and +45°C.
• The lamps connected to the master or slave must all be the same.
• Not suitable for controlling motors (e.g. fans, ventilators).
• The rated power level should never be exceeded.
• Overloading, power surges and short-circuits may irreparably damage dimmers. Before
installation check the circuit carefully and eliminate any of the above causes.
• The dimmer does not have a mechanical circuit breaker in the main circuit and so is not
galvanically separated. The circuit load should be considered always powered.
For further instructions see the manual enclosed with the control panel.
CONFORMITY TO STANDARDS.
For MARINE use, this device has been submitted to the following tests:
IEC 60068-2-52 - Test Kb: Salt mist, cyclic (sodium, chloride solution),
IEC 60068-2-6 - Test Fc: Vibration (sinusoidal)
This device complies with part 15 of the FCC Rules (with the limits for a Class B digital device).
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesidered operation.
49400502A0 01 1309
VIMAR - Marostica - Italy
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising