owner`s guide - Titan Innovations
OWNER'S GUIDE
ADVANCED REMOTE STARTER
FOR MANUAL TRANSMISSION ONLY
www.titan-innovations.ca
Revision 1.01
The owner/user MUST INSTALL a CARBON MONOXIDE
DETECTOR in the living area near to where the vehicle is being
stored or parked. It is the sole responsibility of the owner/user
to keep the remote transmitters away from the reach of
children and handle with care so that the system does not
unintentionally start. When the vehicle is parked in an enclosed
/partially enclosed area (ex: garage, car port...), being serviced
(ex: oil change) or if the vehicle is loaned to an operator not
familiar with a remote starter, the system MUST BE placed in
Service (Valet) Mode.
MANUAL TRANSMISSION STARTERS the installation of a
remote starter MUST only be done with a specified manual
transmission starter. It is the sole responsibility of the vehicles
owner to insure that the vehicle is left with the transmission in
neutral position when the remote starter is in use. The manual
transmission starter is designed to be an added measure of
safety ONLY! The manufacturer does not guarantee or insure
against any damages or loss of life that could result in the
event of a remote starter starting while the vehicle is in gear.
Manual transmission models are designed only to act as a
deterrent against the vehicle starting in gear, this is the
vehicle’s owner’s and operator’s responsibility.
NEVER OPERATE THE SYSTEM IN AN ENCLOSED/ PARTIALLY
ENCLOSED AREA!
Button Operations
Lock
Unlock
Car Finder
Start
ACTION
Press LOCK
Press LOCK
once then press and hold
Press UNLOCK
button once
Press and hold LOCK
for 3 sec
& UNLOCK
Press START
Press and hold START
Press and hold the
Press
button once then
Locks doors* and activates Starter Disable**
Window Roll-up***
Unlocks doors* and deactivates Starter Disable**
Remote panic*
for 3 sec
Trunk release*
buttons simultaneously
Silent Lock or Unlock
Press and hold UNLOCK
Press LOCK
FUNCTION
button once
button once
Remote engine starter on
button for 3 seconds
Remote engine starter off
button for 3 sec
button for 3 sec
Car finder*
Timer Start mode on/off
* This feature is not available for all vehicles.
** Optional feature, requires additional parts & installation.
*** Vehicle must be equipped with factory window roll-up feature.
LOCK
A. Press LOCK
button momentarily.
B. Parking lights will flash 1 time, horn will honk 1 time*, doors will lock.
C. The LED on the antenna will begin to flash slowly.
D. If the optional starter-disable circuit has been installed, it will activate as well.
UNLOCK
A. Press UNLOCK
button momentarily.
B. Parking lights will flash 2 times, horn will honk 2 times*, doors will unlock.
C. The LED on the antenna will stop flashing. (If passive starter-disable is
programmed, the LED will flash quickly for 60 seconds then rearm automatically.)
D. If the optional starter-disable is installed, it will be deactivated to allow the
vehicle to be started by key.
SILENT LOCK/UNLOCK
A. Press both LOCK
and UNLOCK
buttons simultaneously.
B. Parking lights will flash once or twice to indicate doors locking or unlocking.
C. Any programmed horn confirmations are temporarily bypassed.
VALET MODE
This mode disables remote starting and bypasses the starter-disable circuit (if installed).
A. Turn the vehicle ignition key to the on position (you do not need to start the
vehicle).
B. Press and hold the button on the windshield antenna.
C. After about 5 seconds, the parking lights will flash once and you will hear 5 chips
from the vehicle’s horn*.
D. Turn the ignition key to the OFF position. The LED on the antenna will come on
solid.
E. The system should now be in VALET mode.
F. To cancel VALET mode, repeat steps A and B. After 5 seconds, you will see 2
parking light flashes and the horn will chirp 2 times*.
G. The system should now be out of VALET mode.
TRUNK RELEASE --OPTIONAL-The vehicle must be equipped with a power trunk release switch or a power sliding door to
use this option.
A. Press and hold the UNLOCK
button.
B. The doors will unlock and after 3 seconds, the trunk release will activate.
C. The trunk release can also be programmed to work independently on the CAR
FINDER button. If programmed, press and hold the CAR FINDER
button for 3
seconds to activate trunk release.
2nd CAR OPERATION
The system can be setup to operate a 2nd vehicle. This feature must be setup at the time of
installation. See your dealer for details.
A. Press the CAR FINDER
button in conjunction with any other button to perform
that function on the 2nd vehicle.
IDLE MODE (CONTINUOUS RUN)
This option allows you to remove your key and leave the engine running up to the
programmed runtime
A. With the engine running, press the START button.
B. The Horn will chirp twice* and the remote starter will come on.
C. Remove the ignition key and the vehicle will stay running for the length of the
programmed runtime (15 min. default)
D. The vehicle can be shutdown anytime by holding down the START button for 3
seconds or by depressing the brake pedal.
TURBO MODE
This option allows for a cool down on turbo equipped vehicles.
A. With the engine running, press the CAR FINDER
button. (Brake pedal must
not be depressed)
B. The parking lights will flash and the horn will chirp 2 times*.
C. Remove the ignition key and the engine will continue to run for approximately 2
minutes.
PANIC MODE
To use Panic mode, the vehicle’s horn must be connected to your remote starter.
A. Press the LOCK button for 3 seconds.
B. The horn will sound and the parking lights will flash for 60 seconds.
C. Pressing the LOCK or UNLOCK buttons will cancel Panic mode.
CAR FINDER
To use Car Finder mode, the vehicle’s horn must be connected to your remote starter.
A. Press and hold the CAR FINDER button for 3 seconds.
B. The parking lights will flash and the horn will chirp 5 times.
NOTE: Car Finder option is not available when the trunk release option has been
programmed to work on this button
TIMER START MODE
This option allows you to start your vehicle automatically at preset intervals over a 24-hour
time period.
A. Press and release the CAR FINDER button, then press and hold the START button
for about 3 seconds until the parking lights turn on.
B. With the parking lights on solid, select your start interval using one of the 4
buttons on the remote. (See table below)
C. Once you have selected your start interval, the parking light will shut off and
then flash the setting according to the selection you have made. Example: 2 flashes
= 2 hours
D. The vehicle will start every (your selection) hours for a period of 24 hours.
E. To cancel timer start mode, repeat step 1. The parking lights will flash and the
horn will chirp 2 times*
NOTE: Starting the vehicle by key or by remote will automatically cancel timer
start mode.
Button
Flashes
Start interval
LOCK
1 Flash
Vehicle with start every hour
UNLOCK
2 Flashes
Vehicle will start every 2 hours
START
3 Flashes
Vehicle will start every 3 hours
CAR FINDER
4 Flashes
Vehicle will start every 4 hours
REMOTE START SETUP (Ready Mode)
To remote start the vehicle, you must first place the system in’ready
mode’. There are 3 different programming options for doing this. To use
a method other than the default, you must have your system re-programmed by an authorized dealer.
DEFAULT - Transmitter activation
1. With the engine on, transmission in NEUTRAL, apply the park brake.
2. Press and release the START button on the remote transmitter.
3. Remove the key from the ignition (vehicle will stay running)
4. Exit the vehicle and make sure all doors are closed.
5. Press and hold START button on the transmitter to shut the vehicle down.
6. The vehicle can now be started by remote. (ready mode)
OPTION - Brake switch activation
1. With the engine on, transmission in NEUTRAL, apply the park brake.
2. Press and release the brake pedal 2 times (once if it was already on
when you applied the park brake in step 1).
3. Remove the key from the ignition (vehicle will stay running)
4. Exit the vehicle, upon closing the last door, the vehicle will shut down.***
5. The vehicle can now be started by remote. (ready mode)
OPTION - Park brake activation
1. With the engine on, transmission in NEUTRAL, apply the park brake.
2. Remove the key from the ignition (vehicle will stay running)
3. Exit the vehicle, upon closing the last door, the vehicle will shut down.***
4. The vehicle can now be started by remote. (ready mode)
REMOTE STARTING - All modes
A. With the engine off, press the START button.
B. The parking lights will flash and the horn will chirp once (if connected).
C. The vehicle’s ignition system will come on and within 3 seconds, the
vehicle will start. (If vehicle does not start, see the diagnostics section
for possible solutions.)
D. The parking lights will flash 5 times to confirm a successful start.
E. The vehicle will run for the programmed runtime (15 minutes default).
REMOTE START SETUP (Ready Mode) (con’t.)
*** If you press the START button on the transmitter while the door is open,
the system will go into continuous run and NOT shut down when you close
the door. It will run for the programmed run time or until it is shut down by
remote. This feature is convenient if you need to open other doors after
having closed yours.***
IMPORTANT: If a door is opened while the vehicle is not running and in
‘ready mode’, the system will go out of ready mode and will not remote
start. You will need to start the vehicle with the key and repeat the procedure. If you need to open doors and want to avoid repeating the ‘ready
mode’ setup again, simply remote start the vehicle and open the door
while the vehicle is running. When you are done, and the doors are closed, you
can shut down the vehicle with the remote and ready mode will still be engaged.
Diagnostics
If the remote starter does not activate when the
button is pressed, the
park lights will flash a diagnostic code to indicate what shutdown input has
been triggered.
Flashes
Problem
Solution
3 slow flashes
System is in valet mode
Cancel Valet Mode
4 slow flashes
Door Open
Manual trans. models only
5 slow flashes
Ignition ON
Turn off Ignition key and try again
5 flashes
Brakeswitch
Contact your product dealer
6 flashes
Hoodswitch
Contact your product dealer
7 flashes
Tach lock-out
Start vehicle with key, after 5 sec. try again
Battery Replacement
The transmitter battery should be changed at least once every year to maintain
proper operating range. Replace with the appropriate batteries.
SERVICE (VALET) MODE
5 secs
TRANSMITTER LEARNING
Important! The remote starter will hold 4 transmitter codes. It is
recommended that when programming in transmitters, you fill up all
four transmitter codes, even if only using one or two transmitters.
This will clear all other transmitter coding from the unit and prevent
stray coding or possible interference from other remote transmitters.
STEP 1 - Within 3 seconds turn the ignition key to the “ON”
position three times leaving “ON” the third time.
STEP 2 - Press and hold the Program Button. The park
lights will turn “ON” and the horn (optional) will
honk once. Continue to hold the Program
Button, the park lights will turn “OFF” and the
horn (optional) will honk 5 times quickly.
NOTE: If the parking lights do not turn “ON”, release the Program Button and
turn the ignition to the “OFF” position, wait 5sec and repeat steps 1 & 2.
STEP 3a (Default) - While holding the Program Button, press and
release the button on each of the remote
transmitters to be programmed. If using two
transmitters, code in each transmitter twice.
STEP 3b (PadLoc/ - While holding the Program Button, press and
2nd Car)* release the button on each of the remote
transmitters to be programmed.
PadLoc is a safety feature that “LOCKS” the remote transmitter. To
“UNLOCK” the remote transmitter the button must be
pressed simultaneously with the function chosen.
or
2nd Car function allows the operation of two remote starter systems
(in two separate vehicles) with one remote transmitter.
Example: Press and release
and
simultaneously to remote start.
NOTE: Some features not available with PadLoc or 2nd car mode.
The manufacturer warrants to the original purchaser of the remote starter and/or alarm, that the product shall be
free from defects in material and workmanship. However, should this product be proven to be defective, within
a three year period from the original date of purchase, the manufacturer will, without charge to the purchaser
(excluding any charges incurred to have the product delivered to the manufacturer), repair or replace any part of
the remote starter and/or alarm which the manufacturer agrees to be defective. After the initial three year
period the manufacturer shall repair or replace defective products with a nominal processing fee of $35.00
USD. All warranties apply to the original purchaser and the vehicle in which the unit was originally installed
ONLY. Repairs or replacement of defective modules shall remain at the discretion of the manufacturer. All
other parts, components, accessories, and/or optional equipment pertaining to the remote starter and/or alarm
are not included in the manufacturer's warranty. This warranty is non-transferable. Request for warranty
service from any Factory Authorized Dealer must be accompanied with the original purchase receipt. Failure to
comply with any of these conditions may result in warranty being voided. This warranty does not cover the
following: removal and reinstall labor charges, shipping charges, abuse, misuse, or accidental damages to the
remote starter and/or alarm, automobile, and/or parts thereof. This warranty is void upon modification, repairs,
or alterations to any part of the product. The manufacturer does not guarantee or insure against theft of the
vehicle or its contents. Alarm models are designed only to act as a deterrent against possible theft. This alarm
may qualify for auto insurance discounts. Contact your insurance agent for further information. The
manufacturer shall not be held liable for any consequential damages due to breach of this or any other warranty,
expressed or implied. This warranty gives you specific legal rights. Your specific legal rights may vary for each
region.
CERTAIN DAMAGES EXCLUDED – The manufacturer expressly disclaims any liability or responsibility for
incidental damages caused by the product, including economic loss, loss of use of the product, car rentals, or
any other costs relating to the care and custody of the product. The manufacturer disclaims liability or
responsibility for any consequential damages caused by the product or resulting from its use, including the cost
of repairing or replacing other property damaged by the product or caused by its use, whether or not the product
is working properly. The product is intended to deter unauthorized use of the vehicles in which it is installed.
The manufacturer does not warrant that the product is fool-safe against theft and/or vandalism and/or human
error or misuse. The manufacturer accepts no liability or responsibility for any damage of any kind whatsoever
caused to any vehicle in which the product is installed or any resulting damage from its use. The manufacturer
accepts no responsibility or liability for any damage resulting to or theft of the vehicle or its contents caused or
alleged to be caused, directly or indirectly, by failure of the product.
MANUAL TRANSMISSION STARTERS – The installation of a remote starter in a manual
transmission vehicle MUST only be done with a specified manual transmission starter. The
manual transmission starter is designed to be an added measure of safety ONLY! The
manufacturer does not guarantee or insure against any damages or loss of life that could result
in the event of a remote starter starting while the vehicle is in gear. Manual transmission models
are designed only to act as a deterrent against the vehicle starting in gear. It is the sole
This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following
conditions:
(1)
This device may not cause harmful interference, and
(2)
This device must accept any interference received, including interference that may cause undesired
operation.
(3)
CAUTION: Changes or modifications not expressly approved by the part responsible for
www.titan-innovations.ca
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for
compliance void the user’s authority to operate this devise.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising