battery charger kit

battery charger kit
B AT T E R Y
CHARGER KIT
I NSTR UCTIONS F OR USE
M4747A
0$
%DWWHU\&KDUJHU.LW
Instructions for Use
1RWLFH
About This Edition
CAUTION
Edition 2
Printed in the USA
Publication number M3517-91930
Use of accessories other than those
recommended by Philips Medical Systems
may compromise product performance.
This information is subject to change without
notice.
THIS PRODUCT IS NOT INTENDED FOR
HOME USE.
Philips Medical Systems shall not be liable
for errors contained herein or for incidental
or consequential damages in connection with
the furnishing, performance, or use of this
material.
IN THE U.S., FEDERAL LAW
RESTRICTS THIS DEVICE TO SALE ON
OR BY THE ORDER OF A PHYSICIAN.
Medical Device Directive
Edition History
The defibrillator/monitor complies with the
requirements of the Medical Device
Edition 1, August 2000
Edition 2, June 2002
Directive 93/42/EEC and carries the
mark accordingly.
Copyright
Copyright © 2002
Philips Electronics
North America Corporation.
All rights are reserved. Reproduction in
whole or in part is prohibited without the
prior written consent of the copyright holder.
Philips Medical Systems
3000 Minuteman Road
Andover, MA 01810-1099, USA
WARNING
Radio Frequency (RF) interference from
nearby transmitting devices may seriously
degrade performance of the HeartStart XL
defibrillator/monitor. Electromagnetic
compatibility with surrounding devices
should be assessed prior to using the
defibrillator.
ii
Authorized EU-representative:
Philips Medizinsysteme Böblingen GmbH
Hewlett Packard Str. 2
71034 Böbingen
Germany
Canada EMC: ICES-001
&RQYHQWLRQV
This guide uses the following conventions:
WARNING
Warning statements describe conditions or actions that
can result in personal injury or loss of life.
Caution
Caution statements describe conditions or actions
that can result in damage to the equipment or loss of
data.
Note
Notes contain additional information on usage.
iii
Contents
,QWURGXFWLRQ &KDUJLQJ&RQILJXUDWLRQV
&RQILJXUDWLRQ)UHTXHQW8VH
&RQILJXUDWLRQ,QIUHTXHQW8VH 2YHUYLHZRI,QGLFDWRUV &RQQHFWLQJWKH$&3RZHU0RGXOH &KDUJLQJD%DWWHU\
7HVWLQJ%DWWHU\&DSDFLW\ %DWWHU\&DSDFLW\7HVW
&OHDQLQJ([WHULRU6XUIDFHV 7URXEOHVKRRWLQJ
$&3RZHU0RGXOH6SHFLILFDWLRQV 6\PEROV
6DIHW\&RQVLGHUDWLRQV %DWWHU\&DSDFLW\ %DWWHU\/LIH([SHFWDQF\ %DWWHU\6WRUDJH %DWWHU\'LVSRVDO &DOOLQJIRU6HUYLFH v
Introduction
Introduction
The M4747A Battery Charger Kit contains:
z the M3517A AC Power Module
z the M3516A Sealed Lead Acid (SLA) Battery
Pack
z the M3506A Battery Charger Adapter.
These components provide the ability to charge
batteries outside of the M4735A HeartStart XL
Defibrillator/Monitor.
This guide provides directions for using the AC
Power Module and instructions for proper battery
maintenance.
For further detailed information on battery
maintenance, refer to About Sealed Lead Acid
Batteries, an application note. For information on
operating, troubleshooting, and maintaining the
defibrillator/monitor, refer to the M4735A HeartStart
XL Defibrillator/Monitor Instructions for Use.
1
Charging Configurations
Charging Configurations
Charging may take place while the battery is in either
the:
z M4747A Battery Charger,
or the
z M4735A HeartStart XL Defibrillator/Monitor.
Batteries charge to 90% of their capacity in
approximately 3 hours. It will take about 12
additional hours to reach a fully-charged state. It is
important to choose a charging configuration that
allows batteries to be fully charged between uses.
Configuration 1 - Frequent Use
If you use your HeartStart XL more than once a day,
there is not sufficient time between uses to fully
charge batteries in the HeartStart XL. In this
situation, the recommended practice is to charge
batteries using the Battery Charger Kit (as shown in
Figure 1), so that the batteries can reach a
fully-charged state.
Configuration 2 - Infrequent Use
If you use your HeartStart XL less than once a day,
there is sufficient time between uses to fully charge
batteries in the HeartStart XL. In this case, the
recommended practice is to charge the batteries
continuously by leaving the HeartStart XL connected
to AC power (as shown in Figure 2).
2
Charging Configurations
Figure 1 Charging Configuration for Frequent Use
Figure 2 Charging Configuration for Infrequent Use
3
Overview of Indicators
Overview of Indicators
The AC Power Module has three LED indicators that
tell you the status of the power module and the
battery being charged. The indicators and their
meanings are as follows:
Table 1 Indicators
The
Is
Charge Done
Indicator
z Green when the battery is
Charging
Indicator
z Off when the battery is not
Power
Indicator
z Off when power is not
fully charged.
z Off when the battery is less
than 100% charged.
installed in the Battery
Charger Adapter.
z Amber when the battery is
charging.
z Green when the battery is
90% charged.
connected.
z Green when power is
connected.
z Red when there is a problem
with the power module or the
battery being charged.
4
Connecting the AC Power Module
Figure 3
Indicators
&KDUJH'RQH
,QGLFDWRU
&KDUJLQJ,QGLFDWRU
3RZHU,QGLFDWRU
Connecting the AC Power Module
To connect the AC Power Module:
1. Plug the AC Power Module power cord into an
AC power source. (For North America, use only
120 V.)
2. Verify that the Power Indicator illuminates,
showing that power is supplied to the module.
(See Figure 3.)
3. Connect the AC Power Module interface cable to
the Battery Charger Adapter. To do so, align the
white arrow on the power module cable with the
white triangle on the receiving connector; push
the cable into the connector until you hear it click
in place.
5
Charging a Battery
Charging a Battery
A battery in the Battery Charger Adapter begins
charging when the AC Power Module is connected.
As the battery charges, the power module indicators
keep you informed about the battery’s status.
Table 2
Charging Indicators
When the
Caution
Is
Then
Charging
indicator
amber
the battery is
charging.
Charging
indicator
green
the battery is 90%
charged.
Charge done
indicator
green
the battery is fully
charged.
Batteries should be charged until they are fully
charged. This takes about 15 hours. Repeated partial
charging significantly decreases a battery’s life.
Batteries should be charged at temperatures between
10o C (50o F) and 30o C (86o F) for maximum battery
life. Batteries charge more slowly when the
temperature is below 5o C (41o F) or above 40o C
(104o F). Batteries do not charge at temperatures
above 60o C (140o F). Repeated charging at very high
or very low temperatures may shorten the life of a
battery.
6
Testing Battery Capacity
Testing Battery Capacity
As sealed lead acid batteries age due to usage and
storage conditions, their capacity to store and deliver
energy diminishes. The Battery Capacity Test
provides a quantitative measure of battery capacity.
Performing a Battery Capacity Test periodically over
the life of the battery gives an indication of how that
battery is aging, and what level of performance it is
capable of delivering.
A battery’s capacity is affected most by the
frequency of use and by the typical duration of each
use (i.e., how deeply it is discharged before
recharging). General guidelines for performing the
Battery Capacity Test are noted below.
Table 3
Battery Capacity Test Performance Guidelines
Perform a Battery
Capacity Test
Average Usage
Every 6 months
Infrequent use for short
duration*
Every 3 months
Frequent use, or for
longer duration
* “Infrequent use” is less than once per day. “Short duration”
is < 15 shocks, or < 30 minutes of monitoring, or < 6
shocks and 20 minutes of monitoring.
You should also perform a Battery Capacity Test any
time you are concerned about the battery’s
performance.
You may choose to perform the Battery Capacity Test
less frequently if your storage and usage procedures
ensure another charged battery is always available.
7
Testing Battery Capacity
Battery Capacity Test
To perform a Battery Capacity Test:
1. Turn the HeartStart XL off.
2. Label the HeartStart XL to indicate to others that
testing is in progress and the battery may not be
used.
3. Insert a charged battery.
4. If an AC power cord is connected, unplug it.
While pressing Mark , turn the Energy Select
knob to AED On or Manual On to start the test.
5. Allow the test to proceed to completion. The test
takes approximately three hours and is complete
when test results print out and the device turns
itself off.
6. Review the test results and take the appropriate
action, as follows:
Table 4
Battery Capacity Test Results
If
Elapsed Time > 95 minutes
and
Low Battery Time > 10 minutes
Then...
1.
2.
3.
Elapsed Time < 95 minutes
or
Low Battery Time < 10 minutes
1.
2.
3.
8
The battery passed the test.
Record "pass CT" and the date on
the bottom of the battery.
Recharge the battery before use.
The battery failed the test.
Record "fail CT" and the date on
the bottom of the battery.
Discard the battery appropriately.
Cleaning Exterior Surfaces
Cleaning Exterior Surfaces
The Battery Charger Kit should be kept clean and
free of dust. The module is chemically resistant to
common hospital cleaning solutions and non-caustic
detergents. Some of the approved cleaning solutions
are listed below:
z
z
z
z
Isopropyl alcohol (70% in water)
Mild soap and water
Chlorine bleach (3% in water)
Quaternary ammonium compounds, such as Lysol
(10% in water)
When cleaning the power module:
z Avoid pouring fluids on the module. Do not allow
fluids to penetrate the exterior surfaces of the
module.
z Do not use abrasive cleaners or strong solvents
such as acetone or acetone-based compounds.
z Disconnect from AC power source.
z Remover battery from adapter.
9
Troubleshooting
Troubleshooting
Refer to Table 5 if you encounter difficulties while
using the Battery Charger Kit.
Table 5
Problem
The power
indicator does
not light up.
Troubleshooting
Potential Cause
z The power
Possible Solutions
z Check that the power
connection is
compromised.
z A fuse has blown.
z Call for service.
The charging
indicator does
not light up; the
power indicator
is lit.
z The power
z Check connections to the
The power
indicator is red.
z There is a
10
module is unable
to detect a battery.
module is plugged in.
Battery Charger Adapter.
z Make sure the battery is
properly installed.
z Call for service.
problem with the
power module or
the battery in the
power module.
z Remove the battery. If the
battery is the cause of the
problem, the power
indicator turns green.
z If the power indicator
remains red with the
battery removed, call for
service.
AC Power Module Specifications
AC Power Module Specifications
For use only with the M3506A Battery Charger Adapter.
Size: 5.87" (L) x 3.40" (W) x 2.0" (H).
149 mm (L) x 86 mm (W) x 51 mm (H).
_ 21 ounces; 596 grams, including output cord.
Weight: <
Output Cable: 4.0 ft (1.2 m).
_ 10%, 0.4 A max. for battery
Input: 100-240 V AC +
charging.
Output:
Battery Charging: 14.7 V DC, 0.8 A, 12 W; 13.7 V, < 100
mA.
Recommended charging temperature: 10° C (50o F) to
30° C (86o F).
Environmental operating conditions: 0o C to 50o C,
95% maximum relative humidity, 15000 ft altitude (572
hPa).
Transport and storage: -20° C to 70° C, 95% maximum
relative humidity, including condensation, 20000 ft altitude (466 hPa).
Equipment classification:
z Classification with respect to protection from electric
shock: Class 1;
z Degree of protection against ingress of liquids: IPX0;
z Equipment not suitable for use in the presence of a
flammable anesthetic mixture with air or with nitrous
oxide;
11
Symbols
Symbols
The following table lists the meaning of each symbol
shown on the Battery Charger Kit:
!
Caution. (See operating instructions
in instructions for use.)
Output.
Indoor, dry location use only.
No serviceable parts inside.
Safety Considerations
WARNING
Only use the Battery Charger Kit in dry, indoor locations.
WARNING
When using the M3506A Battery Charger Adapter, do not
touch the exposed adapter contacts and the patient
simultaneously.
Note
To disconnect the AC Power Module from power,
remove the power plug from the AC power source.
12
Battery Capacity
Battery Capacity
A fully-charged M3516A battery, operating at room
temperature, provides greater than 100 minutes of
monitoring or more than 50 200-joule charge-shock
cycles.
Battery Life Expectancy
Life-expectancy of a battery depends on the
frequency and duration of use. When properly
maintained and stored, the life-expectancy of a
battery is about 1.5 years. For more aggressive use
models, the life-expectancy may be less.
Battery Storage
Use batteries regularly and rotate them to distribute
the use evenly. When storing batteries, make sure
that the battery terminals do not come in contact with
metallic objects.
Do not store batteries without charging them for
more than one month, if installed in the defibrillator,
or more than three months, if not installed in the
defibrillator. Storage at temperatures between 15oC
(59oF) and 30oC (86oF) is recommended to
maximize life-expectancy.
Caution
Storing at temperatures above 40o C (104oF) for
extended periods of time will significantly reduce a
battery’s life-expectancy.
13
Battery Disposal
Battery Disposal
Discard batteries two years after the date of
manufacture or sooner, if there are visual signs of
damage or if they fail the Battery Capacity Test. The
date of manufacture is located at the bottom of the
battery’s back label. Discard batteries in an
environmentally safe manner. Properly dispose of
batteries according to local regulations.
WARNING
14
Do not disassemble, puncture, or incinerate batteries. Be
careful not to short the battery terminals because this
could result in a fire hazard.
Calling for Service
Calling for Service
For telephone assistance, call the Response Center
nearest to you, or visit our website at:
www.medical.philips/cms.
United States
Medical Response Center
Tel: 800-548-8833
Latin America
Medical Response Center
Tel: 954-835-2600
Canada
Medical Response Center
Tel: 800-323-2280
Other International Areas
Australia
Austria
Tel: 131147
Tel: 43 1 60101 820
Finland
France
Tel: 09 6158 0400
Tel: 0803 35 34 33
Belgium (for Dutch)
Belgium (for French)
Tel: 32 2 525 7102
Fax: 32 2 525 71 91
Tel: 32 2 525 710 3
Fax: 32 2 525 71 91
15
Calling for Service
16
Germany
Italy
Tel: 0180 5 47 50 00
Tel: 800-825087
Netherlands
Poland
Tel: 31 20 547 2555
Fax: 31 29 547 2949
48 22 5710499
Russia
Spain
Tel: 7 095 933 0339
Fax: 7 095 933 0338
Tel: 34 902 30 40 50
Fax: 34 91 326 39 66
Switzerland
United Kingdom
Tel: 0800 80 10 23
Tel: 344 36 633
M3517-91930
Edition 2
Copyright © 2002
Philips Medical Systems
Printed in the U.S.A. June 2002
' "$(&& '
''
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising