luxCONTROL lighting control system DALI actuator DALI

luxCONTROL lighting control system DALI actuator DALI
luxCONTROL lighting control system
DALI actuator
DALI PCD 1-300 one4all
Leading-edge/trailing-edge phase dimmer
Product description
• Digital leading-edge and trailing edge phase dimmers
• Total connected load: 1 – 300 VA
• one4all input: DALI, DSI and switchDIM input
• 1 dimmed phase (output)
• With automatic load detection
• Surface-mounted casing
• Status LED for indicating the operating status
• Suitable for operation with LED retrofit bulbs
• 5-year guarantee
Technical data
Rated supply voltage
220 – 240 V
Mains frequency
50 / 60 Hz
Connected load
1 – 300 VA
Power loss
0.4 W (1.5 W at full load)
Ambient temperature ta
0 ... +50 °C
Type of protection
IP20
È
Standards, page 2
Wiring diagrams and installation examples, page 2
Ordering data
Type
Article number
Packaging, carton
Weight per pc.
DALI-PCD 1-300 one4all
28000441
25 pc(s).
0.085 kg
Specific technical data
Type
DALI-PCD 1-300 one4all
Inputs
Outputs
Input, DALI/DSI
control input and
switchDIM
Current draw
Number of
DALI addresses
Dimmed phase
1
2 mA from DALI
1
1
Data sheet 06/17-CO072-5
Subject to change without notice.
www.tridonic.com
Terminals
Control range, DSI Control range, DALI
0; 1 – 100 %
0; 0.1 – 100 %
0.5 – 1.5 mm²
1
luxCONTROL lighting control system
DALI actuator
Standards
EN 61347-1
EN 61347-2-11
EN 60669-1
EN 60669-2-1
EN 50428
according to DALI standard V1
EN 62386-101
EN 62386-102
EN 62386-205
Glow-wire test
according to EN 60598-1 passed.
Phase dimmers with automatic load detection,
leading-edge or trailing-edge. They are controlled
via switches (switchDIM) or via a DALI/DSI signal.
Total connected load: 1–300 VA
switchDIM:
When a new unit is installed in an existing system
or when the system is first put into operation the
individual units are not synchronised. This means
that some units will be at status on and some at
status off. Pressing the switch briefly will change
the
status; units previously on will be switched off,
but the rest will be switched on. By pressing the
switch for longer than 10 seconds all the units will
be synchronised to the same status. The
synchronisation process is completed when all the
lamps have assumed the same light value (50 %).
The same synchronisation process may also be
necessary during normal operation if an individual
unit becomes unsynchronised because of an
Area of application:
Digital phase dimmers enable low-voltage
tungsten-halogen lamps, in conjunction with
electronic or magnetic transformers, and ohmic
light sources (incandescent lamps) with a total
output of 1 to 300 VA to be dimmed.
Control is either via a DALI/DSI signal or directly
connected switches (switchDIM).
The digital phase dimmer is compatible with LED
retrofit lamps. LV halogen LED retrofit lamps that
are operated by an electronic or magnetic
transformer are also compatible.
incorrect switching operation.
switchDIM is a very simple tool for controlling
ballasts with conventional momentary-action
switches or motion sensors.
To ensure correct operation a sinusoidal mains
voltage with a frequency of 50 Hz or 60 Hz is
required at the control input.
Special attention must be paid to achieving clear
zero crossings. Serious mains faults may impair
the operation of switchDIM.
DALI addressing:
The DALI PCD 1-300 one4all also supports
physical DALI addressing. Press the button
between the terminals to assign the address.
Status-LED for the operating mode:
Normal operation:
LED off
Overload:
LED flashes slow (1/sec.)
Short-circuit:
LED flashes fast (5/sec.)
Permanent short-circuit/overtemperature:LED on
L
N
220 – 240 V AC
50 / 60 Hz
1 – 300 VA
1 – 300 VA
Incandescent lamps,
LED retrofit lamps
switchDIM
N
N
L
switchDIM
DALI PCD 1-300
one4all
DA/D1
DA/D2
LV tungstenhalogen lamps,
LED retrofit lamps
electronic transformator
N
N
L
1 – 300 VA
switchDIM
DALI PCD 1-300
one4all
DA/D1
DA/D2
LV tungstenhalogen lamps,
LED retrofit lamps
magnetic transformator
N
N
L
DALI PCD 1-300
one4all
DA/D1
DA/D2
DALI/DSI
Mixed loads (capacitative, inductive and ohmic) may be used.1)
Different loads require different control signals
by the dimmer.
If various loads are operated simultaneously at
the dimmer, e.g. electronic transformers, magnetic
transformers, LED retrofit lamps, etc., the dimming
signal will focus on the most dominant load. As a
result, the other loads may be operated by wrong
control signals, which will result in improper dimming. In this case, a decrease in the service life of
the loads installed cannot be excluded either.
It is therefore recommended to avoid controlling
different loads simultaneously by the same
dimmer.
1)
Information on starting behaviour
Information on minimum dimming level
Following mains failure and subsequent
restoration of the supply voltage,
the PCD 1-300 will measure the installed
load in order to determine the optimum
control signal.
In the process, the light sources will be
dimmed up and down briefly.
The PCD 1-300 supports in general a
min. dimming level of 1 % for DSI and
0.1 % for DALI. But not every load
supports such low levels.
For that reason the minimum dimming
level is not a static value and is
calculated for every load new.
Data sheet 06/17-CO072-5
Subject to change without notice.
www.tridonic.com
2
luxCONTROL lighting control system
DALI actuator
Wiring type and cross section
The wiring can be in stranded wires with ferrules or solid. For perfect
function of the cage clamp terminals the strip length should be 4 – 5 mm
for the input terminal.
The max. torque at the clamping screw (M3) is 0.2 Nm.
Side D2
max. ∅ � ��� mm
min. ∅ � ��� mm
�–�
Side D1
max. ∅ � ��� mm
min. ∅ � ��� mm
�–�
To get a proper working strain relief it is recommended that the cable jacket
diameter of the side D2 is 2 mm bigger than the diameter of the side D1.
(This can vary if the used cable jacket material varies from side D2 to D1 in
pinching property).
D2
D1
PRESS
Data sheet 06/17-CO072-5
Subject to change without notice.
www.tridonic.com
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising