Idrolava Operations and Parts Manual

Idrolava Operations and Parts Manual
IDROLAVA
PARTS & OPERATIONS MANUAL
REV A
February 2004
TABLE OF CONTENTS
Important Safety Instructions ..................................................... 1
Vacuum and Accessories........................................................... 4
Operation ................................................................................... 5
Daily Maintenance ..................................................................... 11
Vacuum Parts Diagram .............................................................. 13
Warranty Information ................................................................. 17
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution must
always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
WARNING
DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death.
Read and observe all DANGER statements found in your Owner’s Manual and on your machine.
WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other
personnel; property damage could occur as well. Read and observe all WARNING statements found in your
Owner’s Manual and on your machine.
CAUTION: Failure to read and observe all CAUTION statements could result in damage to the machine or to
other property. Read and observe all CAUTION statements found in your Owner’s Manual and on your machine.
DANGER: Failure to read the Owner’s Manual prior to operating or attempting any service or maintenance
procedure to your machine could result in injury to you or to other personnel; damage to the machine or to other
property could occur as well.You must have training in the operation of this machine before using it. If you or
your operator(s) cannot read English, have this manual explained fully before attempting to operate this
machine.
DANGER: Operating a machine that is not completely or fully assembled could result in injury or property
damage. Do not operate this machine until it is completely assembled. Inspect the machine carefully before
operation. Use only as described in this manual. Use only the manufacturer’s recommended attachments.
DANGER: Machines can cause an explosion when operated near flammable materials and vapors. Do not use
this machine with or near fuels, grain dust, solvents, thinners, or other flammable materials.
DANGER: Components used in packaging (ex: plastic bags) can be dangerous; keep away from children and
animals.
DANGER: Do not pick up flammable fluids, dust or vapors.
DANGER: Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
DANGER: This machine is not suitable for picking up health endangering dust.
DANGER: Using a machine with a damaged power cord could result in an electrocution. Do not use the
machine if the power cord is damaged. Do not use the electrical cord to move the machine. Keep cord away
from heated surfaces. Do not unplug by pulling on the cord; grasp the plug, not the cord. Turn off all controls
before unplugging. Do not close a door on cord or pull around sharp edges or corners.
DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that is not properly
disconnected from the power source. Disconnect the power supply before attempting any maintenance or
service.
DANGER: Keep jet directed away from all electrical switches and connections.
DANGER: The machine should never be immersed in water or a pressure jet of water be used for cleaning.
DANGER: Electrical components can “short-out” if exposed to water or moisture. Keep the electrical
components of the machine dry. Always store the machine in a dry area.
Page 1
WARNING: Operating a machine without observing all labels, decals, etc., could result in injury or damage.
Read all machine labels before attempting to operate the machine. Make sure all of the labels are attached or
fastened to the machine. Get replacement labels and decals from the manufacturer’s distributor.
WARNING: Use of this machine to move other objects or to climb on could result in injury to the operator or
damage to the machine. Do not use this machine as a step or furniture. Do not allow to be used as a toy. Close
attention is necessary when used by or near children.
WARNING: Electrocution could occur if you handle the plug or appliance with wet hands. Do not handle plug or
appliance with wet hands.
WARNING: Rotating fan blades inside the cover. Before opening cover, switch off machine.Wait until the fan/brush
stops completely or dust and debris may be ejected.
WARNING: If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into
water, return it to an Authorized service center.
WARNING: Damage could occur to machine if openings are blocked. Do not put any object into openings. Do not use
with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
WARNING: Injury to the operator and/or damage to the machine could occur when cleaning on stairs, unless extra
caution is used. Use extra caution when cleaning on stairs.
WARNING: To reduce the risk of electrical shock, always use a 3-wire electrical system connected to the electrical
ground. Whenever possible connect the machine to an outlet protected by a ground fault interrupter (GFCI). See
“Grounding Instructions.”
WARNING: The suction nozzle should be kept away from the body, especially delicate areas such as the eyes, ears
and mouth.
WARNING: Moving parts of this machine can cause injury and/or damage. Keep hands, feet, loose clothing,
hair, fingers, and all parts of the body away from openings and moving parts.
WARNING: When all work is completed and the pump is off, the pressure must be discharged by depressing the
valve lever.
CAUTION: Should extension cords be used, ensure that the cable rating is suitable for use with the equipment. Do
not use the cable coiled as this could result in a voltage drop or overheating. Keep dry at all times.
CAUTION: If the equipment should overturn, it is recommended that that the machine be righted before
switching off.
CAUTION: If foam or liquid should come from the machine exhaust, switch off immediately.
CAUTION: Aggressive solvents or detergents should not be used.
CAUTION: Never run the pump without liquid as this may result in damage.
SAVE THESE INSTRUCTIONS
Page 2
Page 3
VACUUM
INJECTION/EXTRACTION
PARTS LIST
PARTS LIST
C. Vacuum Head
D. Solution Tank
E. Tank
F. Suction Inlet
G. Flexible Hose
H. Solution Hose
I. Upholstery Tool
K. Injection Trigger
M. Straight Wand
N. Solution Hose
O. Bent Wand
P. Bent Wand w/Trigger (K)
Q. Carpet Tool
R. Squeegee Brush Shoe
Y. Solution Intake Hose
B. Purifying Tank
C. Vacuum Head
E. Tank
F. Suction Inlet
G. Flexible Hose
M. Straight Wand
P. Upper Bent Wand
S. Double Use Brush
T. Round Brush
U. Hand Tool
V. Crevis Tool
Ω Idro Device
Page 4
SET UP & OPERATION
Air Filtering and Dry Vacuuming
1. Attach the Idro device
to the tank inlet deflector
located at the inside of the tank.
2. Fill with water up to the
bumper (1-1/2 gallons).
6. Attach hose into inlet.
7. Attach appropriate
accessory. For power head
assembly, see power head wand
assembly on page 8. For double
use brush, see Extraction Wand
Assembly to change from carpet
tool to double use brush
attachment on page 9 and 10.
Fill line
3. Insert purifier into tank.
8.Activate the vacuum by pressing the red switch
on vacuum head.
4. Ensure cartridge filter “L” is
secured to the vacuum head by
the filter bracket “Z”. Turn
clockwise to secure, counterclockwise to remove.
9.Turn the vacuum speed knob located on top of
the vacuum head to:
-Air Filtering for air filtration use.
-Vac Cleaning for vacuuming use.
5. Place vacuum head C onto
the tank and lock into place with
the 2 clamps.
Page 5
Wet Pick-Up
1. Remove Idro device (if
attached) from tank.
2. Insert purifier into the
tank.
3. Attach hose to the inlet.
4. Attach extraction wand (see
Extension Wand Assembly, page 9.
5. Activate the vacuum by pressing the red switch on vacuum head.
6. Turn the vacuum speed control knob located on top of the vacuum
head to shampoo setting.
Page 6
Injection - Extraction Washing
7. Connect the solution hose to
the power head by simply
inserting the male hose end
fitting into female fitting until it
locks. To remove, press red
button to unlock and pull apart.
1. Remove cartridge filter L and
retainer Z from vacuum head.
8. Connect trigger gun to the
solution hose.
2. Remove air purifier and
Idro unit from the tank.
9. Attach appropriate accessory:
- Wand and carpet tool for
carpets. See Extraction Wand
Assembly, page 9.
- Wand, carpet tool and
squeegee brush shoe for hard
floors. See Extraction Wand
Assembly, page 9.
- Upholstery tool for upholstery
3. Pour cleaning solution and
water into the solution tank.
10. Turn the vac speed control
knob located on top of the
vacuum head to the shampoo
setting.
4. Insert the solution tank into
the recovery tank.
Y
5. Attach the vacuum head onto
the tank by guiding the solution
hose Y into the solution tank,
Clamp the vacuum head to the
tank.
6. Connect vacuum hose to the
tank.
11.Press the green switch to
activate the solution pump.
Press the red switch to activate
the vacuum motor.
12.To clean, press trigger to
inject cleaning solution, press
tool down firmly and pull towards
you.
Page 7
POWER HEAD AND WAND ASSEMBLY
Locking Collars
1. Locate power head wands and locking collars.
The power head wands do not have the solution
hose guides. The wand pieces with the solution
hose guides are for the extraction wand (see
picture 1 under Extraction Wand Assembly to
identify extraction wand). Slide on the two collars
as pictured.
4. Firmly press upper bent wand and trigger into
the straight wand
5. Attach two cord hangers to wand and cord.
2. Insert wand into the power head neck until it
stops. Slide the small collar into the neck of the
power head. Screw the large collar onto the
powerhead until tight.
6. Evenly attach 3 cord hangers to the hose and
cord.
3. Firmly press the two wands together.
7. Plug power head into the power head
receptacle.
Page 8
EXTRACTION WAND ASSEMBLY
Solution hose guides
1. Locate the lower bent wand piece and
the straight wand piece. The solution hose guides
molded on one side easily identify these pieces.
5. Press the solution hose into the solution hose
guide, starting at nozzle.
2. Firmly press the lower bent wand piece into the
straight wand piece. Make sure the solution hose
guides are aligned with each other.
6. For hard floors only, snap squeegee brush shoe
onto carpet tool.
3. Firmly press the lower bent wand piece into the
carpet tool.
7. Firmly insert upper bent wand and trigger into
the straight wand.
4. Clip injection nozzle to carpet tool.
8. Connect solution hose to the trigger by inserting
until it locks into place. To remove, press the red
button and pull the connector out of the trigger.
Page 9
TO CHANGE FROM CARPET TOOL TO
DOUBLE USE BRUSH ATTACHMENT
1. Unclip the injection nozzle from carpet tool.
3. Firmly press the double use brush attachment
into the lower bent wand piece.
2. Remove carpet tool from lower bent wand
piece.
4. The injection nozzle and hose serves no
function for the double use brush. Either remove
or attach the injection nozzle to the wand assembly so it does not interfere with vacuuming.
Page 10
DAILY MAINTENANCE
Caution: Some detergents produce foam which will damage the vac motors. The vac shut-off
may not be sensitive to all foams. Be sure to check that the tank is not filling with foam. Use
a defoaming agent to avoid pulling foam through the vac motor. Should vac motor become
wet, remove source of overflow and immediately run vac motor open to dry.
At the end of each working day:
1. After each use, rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate if necessary, using a hospital grade virucide or a 1:10 bleach to water solution. Waste water
should be disposed properly.
2. Remove head assembly and allow tank to dry.
3. Remove filters for cleaning or allow to dry.
4. Inspect hoses for wear. Frayed or cracked hoses should be replaced to avoid vacuum loss.
5. Inspect power cord for wear. This cable will lay on wet surfaces. To prevent electrical shock
replace cords with frayed or cracked insulation immediately.
Page 11
POWER HEAD
POWER HEAD
POS
P/N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
60.
S80117
S80138
S80139
S81006
S80450
S82589
S81026
S82588
S81050
S81050
S8231IDRO
S80484
S80756
S81006
S83732
S83937
S81050
S82633
S83969
S82627
S80310
S81006
S82634
S83901
S81120S
S83901
S83866
S82636
S83658
DESCRIPTION
QTY
Power cord
Strain Relief
Clamp
Screw, 5 x 20
Terminal, block
Cover, hook
Screw, 5 x 30
Handle
Screw, 5 x 35
Screw, 5 x 35
Cover, top
Switch
Switch
Screw, 5 x 20
Potentiometer
Filter
Screw
Cover, middle
Gasket
Screw
Plug
Screw
Plate, motor
Gasket
Motor, 120V
Gasket
Foam muffler
Base
Resistor
1
1
1
2
1
1
4
1
2
2
1
1
1
4
1
1
4
1
1
6
1
4
1
1
1
1
1
1
1
PUMP
Page 12
POS
P/N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
S83037
S82743
S82660
S82659
S83036
S82689
S82571
S82603
S81005
S80799
S82602
S81979
S81979
S83035
S81610
S86075
S82604
S86082
S86118
DESCRIPTION
Terminal protector
Hose, L=700mm
Clamp
Clamp
Filter housing
Filter, solution
Gasket
Bracket, pump
Screw, 5 x 14
Pump, 110V, 60 Hz
Clamp
Screw, 5 x 25
Screw, 5 x 25
Fitting, “Y”
O-ring
Quick disconnect, female
Clamp
Grommet
Sleeve
QTY
1
1
1
1
1
1
2
1
2
1
2
4
2
1
1
1
1
1
1
SOLUTION TANK ASSEMBLY
SOLUTION TANK
POS
P/N
1
2
3
4
5
6
7
S83214
S82622
S82598
S82597
S82580
S82622
S82592
S82638
FILTER SYSTEM
POS
P/N
1
2
3
4
5
6
7
8
9
10
11
12
S83706
S83724
S86260
S86281
S86278
S86369
S83156
S86287
S86282IDRO
S86413
S86277
S86142
S86288
DESCRIPTION
QTY
Spacer
Screw, 5 x 25
Filter, cartridge
Filter, locking ring
Filter, plate
Screw, 4.2 x 16
Screw, 5 x 20
Washer
Support
Center block
Air director
Filter, 50 mm φ
Complete Filter Kit
4
4
1
1
1
4
4
4
1
1
1
1
IDRO DEFUSER
POS
P/N
1
2
3
4
5
8
S86191
S86192
S83049
S86193
S87638
S86194
S86198
POS
P/N
1
2
3
4
5
6
7
8
9
10
11
12
S82643
S81300
S81847/S
S81026
S82846
S82586
S82608
S82593
S82594
S82583
S82630
S80558
DESCRIPTION
QTY
Deflector
Gasket
Screw, 3.5 x 13
Flange
Tube, defuser
Defuser
Complete IDRO Diffuser Assembly
1
1
4
2
3
1
TANK
DESCRIPTION
QTY
Tank
Rivet, 5 x 24.5
Clamp, tank
Screw, 5 x 30
Gasket, φ38
Inlet, base
Spring
Deflector
Button
Inlet, cover
Bumper
Caster
1
4
2
4
1
1
1
1
1
1
1
4
Page 13
DESCRIPTION
Handle
Screw, 4.2 x 16
Extension, tank
Tank
Sleeve
Screw, 4.2 x 16
Filter
Complete Solution Tank
QTY
1
4
1
1
1
1
1
WAND ASSEMBLY
WAND/TRIGGER ASSEMBLY
POS
P/N
1
2
3
4
6
7
S86167
S86158A
S86188
S86160OTT
S86240IDRO
S86261IDRO
S86175
DESCRIPTION
QTY
Button
Curved plastic
Cuff
Trigger
Wand,straight
Wand, curved
Complete Trigger
1
1
1
1
1
1
WAND/HEAD ASSEMBLY
POS
P/N
1
S82732
2
S83171
3
S82747
4
S82711
5
S83060
6
S83071
7
S83664OTT
8
S82713
9
S82730
10
S82731
11
S82727
12
S86252
1-8
S83572
9-12
S82753
S82724
DESCRIPTION
Spray tip housing
Plastic sleeve
Hydrolitic hose
Filter
Gasket
Nozzle
Quick disconnect, male
Cap
Extraction head
Plate
Screw
Screw
Complete Spray Nozzle Assembly
Complete Extraction Head
Complete Extraction Wand Assembly
QTY
1
2
1
1
1
1
1
1
1
1
2
5
HARD FLOOR TOOL
POS
P/N
1
2
3
4
5
6
7
S82733
S82734
S83460
S82748
S83047
S83049
S82729
S82707
Page 14
DESCRIPTION
Body, hard floor tool
Strip
Blade, hard floor tool
Brush/floor tool
Rear brush, hard floor tool
Screw
Suction strip, L= 250
Complete Liquid Tool
QTY
1
1
1
1
1
4
1
HAND TOOL
HAND TOOL
POS
P/N
1
2
3
4
5
6
7
8
9
10
11
12
S80652/B
S82824
S83257
S82713
S82759
S82711
S83060
S81005
S82826
S83171
S82658A
S86077
S86174
DESCRIPTION
QTY
Cuff
Housing
Screw, 4.2 x 13
Retainer, nozzle
Nozzle
Filter
Ring
Screw, 5 x 14
Base, nozzle
Clamp
Tube, L= 75 mm
Connector, male
Complete Hand Tool Assembly
1
1
4
1
1
1
1
2
1
2
1
1
DRY TOOLS
S
T
U
V
DRY TOOLS
POS
P/N
S
T
U
V
S70632
S70004
S70616
S70617
S71685
Not Shown
DESCRIPTION
Double Use Brush
Round Brush
Hand Tool
Crevice Tool
Hose
Page 14
QTY
1
1
4
1
1
Warranty Policy
Limited Warranty
Eagle Power Products (EPP) warrants new cleaning equipment against defects in material and
workmanship under normal use and service to the original purchaser as detailed below.
10 Years
Subject to the conditions stated below, EPP warrants polyethylene tanks and housings to be
free from defects in materials and workmanship for a period of ten years.
3 Years
Subject to the conditions stated below, EPP warrants all automatic scrubber components to
be free from defects in materials and workmanship for a 3-year period. Parts replaced or
repaired are warranted for the remainder of the original warranty period.
1 Year
Subject to the conditions stated below, EPP warrants all other cleaning equipment
components to be free from defects in materials and workmanship for a 1-year period. Parts
replaced or repaired are warranted for the remainder of the original warranty period.
Batteries are prorated for one year.
EPP will furnish and charge for replacement parts, including transportation, to the original
owner through an EPP authorized service center. If the part is returned within 30 days and is
found defective, the owner will be credited for the cost of the replacement part including
shipping and handling.
Labor charges are covered for one year from the date of purchase if provided by an authorized
EPP service center. Travel is covered for 90 days for battery operated equipment only.
Wear items exempt from warranty include belts, carbon brushes, power cords, wheels, pad
drivers, clutch plates, brushes, pads, handle grips, filters, screens, throttle cables, and squeegees.
This warranty shall not apply to failures caused by misuse or abuse, improper
maintenance as stated in the operation manuals, use of unauthorized repair parts, repairs
by other than an EPP authorized service center, and damage in transit.
EPP disclaims and denies any liability for any direct, indirect, special incidental or consequential damage which may
be suffered as a result of sale, delivery, servicing, use, loss of any product, downtime, labor, freight, or other charges
not expressly included herein.
Date Purchased:
Model Number:
Serial Number:
Please be sure to record this information. This information will be necessary for future warranty claims.
Eagle Power Products Sales and Service Provided by:
1174 Northland Drive Mendota Heights, MN 55120
651.686.5399 Fax 651.686.5695
www.eaglepower.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising