Introduction Features Specifications Controller Diagram Connecting

Introduction Features Specifications Controller Diagram Connecting
Optical Fiber • Custom LED • Drivers & Transformers • Control Systems
SRC 144 Control Manual
Introduction
Thank you for choosing our SRC 144 DMX controller. This unit is capable of serving as the master control
unit to slave DMX controllers. Up to 450 scenes can be inserted into 9 programs for 9 projecting LED
lighting fixtures.
Features
54 DMX Channels
Manual / Auto Control
9 Program slots, 50 scenes each
6 Control channel sliders
Variable cross fading time and static time control
Specifications
Dimensions: 12” x 7” x 3”
Weight: 1.75 kg (3.8 lb)
Power Voltage: 9V – 12V DC
Protocol: DMX 512
Output Port: 1 x female 3-Pin XLR3 connector
Controller Diagram
When all displays show zeros, it is in default mode.
(To exit to default mode, press the button to which the current mode is at)
A dot next to the number in the display represents the selected screen.
Connecting DMX Lighting
The SRC 144 controller has a female DMX port at the back. DMX lighting units can be connect to the back
of the controller via a XLR3 connector cable.
The projector range for the DMX lighting units are:
Projector Number
1
2
3
4
5
6
7
8
9
Lighting Unit DMX Address
1 to 6
7 to 12
13 to 18
19 to 24
25 to 30
31 to 36
37 to 42
43 to 48
49 to 52
Units set to the same starting DMX address will be controlled simultaneously.
-1111 – 8838 Heather St. Vancouver BC Canada V6P 3S8 • Ph: 1-604-874-4405 Fx: 1-604-321-0445 • www.bllighting.com • sales@bllighting.com
Optical Fiber • Custom LED • Drivers & Transformers • Control Systems
Programming
Adding Scenes
1) Make sure the controller is in default mode
2) Hold Program, until flashing (the flashing display represent in programming mode)
- The dot will appear next the display of selection
3) Press Projectors to move selection (dot) to projectors display
4) Press Up or Down to change the projector number
5) Slide the Control Channels to adjust the projectors
6) Press Insert to add scene
- The numbering of scenes starts at #00; the first scene will be created in #00
- Make sure all projectors are set before Insert
- Scenes cannot be directly overwritten, they must be deleted first then added
7) Press Select to switch between programs and scenes display (dot) to preview the scenes (Up or
Down to adjust the number)
8) Press Program to exit programming mode
Deleting Scenes
1) Make sure the controller is in default mode
2) Hold Program, until flashing (the flashing display represent in programming mode)
3) Press Delete once (the Scenes display will start to flash)
4) Press Delete again to confirm
5) Press Program to exit programming mode
Deleting Entire Programs
1) Make sure the controller is in default mode
2) Hold Program, until flashing (the flashing display represent in programming mode)
3) Press Delete once (the scenes display will start to flash)
4) Press Program (the scenes display will show “All”)
5) Press Delete again to confirm
6) Press Program to exit programming mode
Running the Programs
Auto-Run
1) Make sure the controller is in default mode
2) Press Program to begin displaying the scenes
- The dot will appear next the display of selection
3) Press Up or Down to cycle through programs
4) Scroll Control Channel #1 to adjust the static time
5) Scroll Control Channel #2 to adjust the cross fade time
6) Press Programs to exist run program mode
Auto-run with Manual Control
1) Make sure the controller is in default mode
2) Follow the instructions from 5.1 Auto-Run
3) With the program running, press Projectors
- The dot will appear next to display of selection
4) Press Up or Down to scroll through projectors
5) Slide the Control Channel to manually adjust the projectors
- The projectors display will flash
- The static and cross fade time Control Channel will be temporary replaced by RGB control
- The projector display will flash, indicating that Control Channel is in manual control
6) Press Projectors to exit manual control
7) Press Programs to exist run program mode
Manual Control
1) Make sure the controller is in default mode
2) Press Projectors to enter manual mode
- The dot will appear next to display of selection
3) Press Up or Down to scroll through the projectors
4) Slide the Control Channels to adjust the projectors
5) Press Projectors to exit manual control
-2111 – 8838 Heather St. Vancouver BC Canada V6P 3S8 • Ph: 1-604-874-4405 Fx: 1-604-321-0445 • www.bllighting.com • sales@bllighting.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising