Diversa PIR WOR 347 Install Guide for web

Diversa PIR WOR 347 Install Guide for web
Installation Guide
PART NO.
WORSI32-P-N
standard lens, PIR,
347Vac, 2-pole,
photo sensor
WORXI32-P-N
extended range lens,
PIR, 347Vac, 2-pole,
photo sensor
Diversa
Line Voltage
Occupancy
Passive&Infrared
Vacancy(PIR)
Sensors
Occupancy
- Recessed
/ Vacancy
Ceiling,Sensor
Passive Infrared (PIR), 347Vac
Installation
FEATURES
Wiring
• Commercial grade components for long term reliability
Diversa 347Vac sensors include #14AWG wiring leads. Use appropriate sized wire nuts for connecting wires.
• Straightforward wiring for quick installation
CAUTION: Turn power off at the circuit breaker before working on sensor. According to NEC 240-83(d), if the branch
circuit breaker is used as the main switch for a fluorescent lighting circuit, the circuit breaker should be marked SWD.
All installations should be in compliance with National Electric Code (NEC) and all state, provincial, federal, and local
codes.
• Factory configured for the most common applications
• DIP switches and dials for advanced functionality
Instructions
Black
Operation
Black/White
Diversa 347Vac sensors draw control power directly from the lighting circuit they are intended to control. When in
operation the sensor will detect initial motion using Passive Infrared (PIR); once motion is detected, the internal
contact will close. Motion through PIR is used to maintain the occupied condition as long as occupants remain
within coverage range of Sensor.
DIP Switches
=T
est
M
e
Auto Time LED
Power
• 347Vac
• 60Hz
Neutral
Load
Switch
Blue
7 ft
0 ft
Line
7 ft
Blue/White
Switch
Load
Neutral
14 ft
Side View
9 ft
White
• Ensure that the sensor is at least 30 inches away from air handlers/registers and not pointed directly at
windows
• Check that you are installing the right product (check the product model number) as per the drawings
od
SPECIFICATIONS
14 ft
To optimize the performance of Diversa Sensors, please review the coverage pattern, range, and model to
match with the application. Room dynamics will change when people and furniture are occupying the space.
In some rooms, after move in, some sensors may require adjustments.
(Shown with cover
plate removed)
Photo Level Dial
Used to determine light
level for Photo Functions
Top View
Sensor Location Guidelines
Test Mode LED
ON
Installing in Smaller Room (Standard Lens)
• Locate the sensor near the entrance door wall to prevent it from viewing out into the hallway.
• Positioning the sensor in this manner ensures that an occupant moves across the longest detection beam
upon entrance, utilizing the sensor's maximum PIR range.
• Optimal usage is to detect small motions such as hand movements
• Designed for a mounting height of 7-15 ft
2-pole
No Neutral
• Photo Sensor for Natural Daylight control
Line
Manual Override Button
14040700-C
Sensor Location Guidelines for “P” models
•
•
•
•
•
Time Delay Dial
Ranges from 30s to 30 min.
Full turn Clockwise for Auto Time
Full turn Counterclockwise for Test Mode
Place outside the direct cone of light from fixtures
Between 3 to 12 feet from windows
As close as possible to the fixture being controlled
Above the least illuminated space in the work area
Away from lighting that is not being controlled by the sensor
Typical Enclosed Office
0 ft
14 ’
12 ’
10 ’
6’
3’
0’
3’
6’
10 ’
12 ’
14 ’
Extended Lens for Larger Rooms
• Place the sensor near the center of the room ceiling. Locate it so the approximate distance of 27ft in
or in dead center of room.
• Tilt the lens to aim the detection zone to the bottom of the door.
• Positioning the sensor in this manner ensures that the beam does not reach outside the room without
reducing sensitivity.
• Optimal usage is to detect large motions such as walking.
• Designed for a mounting height of 7-15ft.
Top View
DIMENSIONS/MOUNTING
inches (mm)
27ft
27 ft
C
14 ft
27ft
• Unit attaches to mounting ring with
0 ft
screws or it can be mounted into an
octogan box.
14 ft
Ceiling tile
Contact Ratings
• 347Vac - 800W
Power Consumption
• 5.7mA
0.88”
(2 2 )
Typical Classroom
DIPs and Dials
under cover
plate
4.17”
(106)
3 0 ° Tilt
• The WOR sensor will fit an octagon
box. It is very important that conduits
be attached at opposite ends of the
box.
Conduit
Octagon Box
• Use a 2 1/8 ” or more, deep box.
If the box is less, use the spacer ring.
Diversa by Douglas Lighting Controls
27 ft
Side View
9 ft
2.0”
(52)
Approvals
• Certified to UL 508, UL244A, CSA C22.2 #14
Environment
• Indoors, stationary, non-vibrating, non-corrosive atmosphere an
non-condensing humidity
• Ambient Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -14°F to 140°F (-25°C to 60°C)
Mounting
ring
Wire
www.douglaslightingcontrols.com
0 ft
27 ’
16 ’
9’
3’
0’
3’
9’
16 ’
27 ’
Installation Guide
Diversa
Line Voltage
Occupancy
Passive&Infrared
Vacancy(PIR)
Sensors
Occupancy
- Recessed
/ Vacancy
Ceiling,Sensor
Passive Infrared (PIR), 347Vac
General Programming Instructions
This covers mode programming using the onboard DIP and Dial switches.
Factory Defaults
All DIP switches in DOWN position. Time delay: 10 minutes; Natural Daylight level: 50% (200 lux).
DIP Switch Modes
Troubleshooting
DIP 1 - PIR Detection LED
Before calling Technical Support, please review the following Troubleshooting Guide.
LED in Sensor’s PIR window flashes GREEN when PIR detects motion. LEDs can be turned OFF with DIP switch. Sensor
continues to function.
DIP 2 - Walk-Through Mode
***NOTE***
Diversa Occupancy Sensors with a “P” in the model number contain a Photo Sensor that is
controlled by DIP 6. The factory default for Natural Daylight Mode = ENABLED (DIP 6 DOWN).
This mode disables the Manual Override Button. To test sensor functionality, you may need
to disable Natural Daylight Mode (DIP 6 UP) to test sensor functionality.
14040700-B
Issue
When Enabled and Occupancy switches lights to ON and sensor does not detect motion after 30 seconds of light ON,
an OFF Time Delay of 3 minutes is used (OFF Time Delay must be greater than 3 minutes). If motion is detected after
30 seconds of lights ON, the configured OFF Time Delay is followed.
DIP Switches & Dial Settings
1
Function
PIR LED
UP
DOWN
Default
Disabled
Enabled
DOWN
2
Walk-Through
Mode
Enabled
Disabled
DOWN
3
Manual Override
Disabled
Enabled
DOWN
4
Sensor Mode
Manual ON (Vacancy)
Auto ON (Occupancy)
DOWN
5
PIR Sensitivity
High
Medium
DOWN
6
Natural Daylight
Mode (”P” Models)
Disabled
Enabled
DOWN
Inactive
Inactive
DOWN
7
8
Sensor is set to Manual ON Mode.
Check DIP 4. Move DOWN for Auto ON.
Sensor is set to Natural Daylight Mode (Photo
Inhibit) and Sufficient Natural Light is Present.
This only applies to Photo Sensor (”P”) models. Check DIP
6. If DOWN, sensor is in Natural Daylight Mode, therefore
lights will only turn ON if there is insufficient natural
daylight. Rotate the Light Level Dial clockwise pressing
the Manual Override Button until the Lights turn ON.
Natural Daylight mode can be disabled by moving DIP 6
UP.
DIP 4 - Sensor Mode
Vacancy Mode - Lights must be turned ON manually when entering a room and are automatically turned OFF when
occupancy no longer detected. Maximizes energy savings because lights are only turned on when lighting is
required.
Lights will not turn
ON automatically
Occupancy Mode - Automatically turns lights ON when occupancy is detected in a room and automatically turns
lights OFF when occupancy is no longer detected. This is a very convenient mode as lighting controls never have to
be touched. Because lights are always turned on when Occupancy is detected regardless of the need for lighting,
this is less energy efficient than Vacancy Mode.
Manual Override Button was used to turn lights
OFF.
Check the wiring diagram. Ensure ground is connected.
With DIP 1 DOWN, check for motion detection by waving
hand in front of sensor lens. Activation LED will blinnk
green.
Sensor is set to Natural Daylight Mode (Photo
Lights will not turn Inhibit) and Sufficient Natural Light is present.
This only applies to Photo Sensor “P” models. Check DIP 6.
If DOWN, sensor is in Natural Daylight Mode; therefore,
lights will only turn ON if there is insufficient natural
daylight. Rotate the Light Level Dial clockwise pressing
the Manual Override Button until the lights turn ON.
Natural Daylight mode can be disabled by moving DIP 6
UP.
Power has been interrupted
connection is intermittent.
Can be moved from Medium sensitivity (default) to High sensitivity if sensor is not recognizing Occupancy.
DIP 6 - Natural Daylight Mode (”P” models)
or
When ENABLED, lights ON when Occupancy detected AND daylight level is below Light Level Dial setting. With lights
ON, an increase in daylight above the Light Level Dial setting will not force lights OFF.
DIP 7 - Not Used
DIP 8 - Restroom Mode (2-pole models)
Pole 1 and Pole 2 are set to synchronize to the same Photo and Time Delay settings. With Restroom Mode = Offset,
Pole 2 will activate at the same moment as Pole 1 when Occupancy detected; however, Pole 2 will be offset so that
OFF delayed 50% longer than Pole 1. (e.g. Light is Pole 1 and Fan is Pole 2. Fan would stay ON 50% longer than light).
ON Manually
Auto Time Mode
Activated when Time Delay Dial is set to Auto Time. Red LED indicator will be ON. In this mode, time delay will start
automatically set by the sensor learning occupancy patterns.
Power has been interrupted
connection is intermittent.
or
wiring
Test Mode
Not used
Restroom Mode
(2-pole models)
Offset
Synchronized
Activated when Time Delay Dial is set to TEST. Test Mode LED will flash red for 5 minutes, providing a short Time Delay
when testing the installation to determine if the sensor is working as intended or requires adjustments. After 5
minutes, LED will stop flashing and Time Delay reverts to Factory Time Delay setting (10 minutes).
Sensor is in Auto Time Mode.
DOWN
Wait for OFF Time Delay to count down, then with
motion detected lights will turn ON. Manual Override
Button can be disabled by moving DIP 3 UP.
wiring
DIP 5 - PIR Sensitivity
Some DIP Switches C ontrol Optional Features Not Found on All Products
DIP #
Recommended Solution
DIP 3 - Manual Override
Manual Override Button can be disabled with DIP switch to prevent manual ON/OFF.
• Start with the PIR Sensitivity at Medium (DIP 5 DOWN)
• To set the light level at which you want to prevent the sensor from turning light ON, rotate Light Level
Dial to adjust the light level
• To enable Restroom Mode , ensure that DIP 8 is UP. In this mode Pole 2 will remain on 50%
longer than Pole 1 (time is set with the Time Dial) and Pole 2 cannot be Photo Inhibited
Possible Cause
Lights will not turn
Check the wiring diagram. Ensure ground is connected.
With DIP 1 DOWN, check for motion detection by waving
hand in front of sensor lens. Activation LED will blinnk
green.
If the Sensor is in AUTO Mode, it may take longer than
expected to turn the lights off. Set the Time Delay to 5
minutes and leave space to determine if the Sensor is
functioining. The maximum Time Delay is 30 minutes.
OFF automatically
Sensor may be detecting heat from HVAC registers or
Sensor is being activated by a heat source other
than occupant.
Factory DIP & Dial Settings
other heat sources. Check Installation location for heat
source. Reduce PIR sensitivity by moving DIP 5 DOWN.
Move sensor location – see guidelines.
UP
Lights will not turn
DOWN
OFF Manually
1
2
3
4
5
Diversa by Douglas Lighting Controls
8
Test Mode LED
10
5
Hi
7
Time Delay Dial
Light Level Dial
Photo Sensor “P” models only
Lo
6
20
1
30
TEST
(=LED ON)
Auto Time
www.douglaslightingcontrols.com
Manual Override Button has been disabled.
Move DIP 3 DOWN to enable Manual Override Button.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising