User Manual
TABLE OF CONTENTS
TECHNICAL SPECIFICATIONS
SAFETY INSTRUCTIONS
KEY PARTS DIAGRAM
OPERATING INSTRUCTIONS
MAINTENANCE
WARRANTY
WARNING!
For use with the compatible Maximum® batteries only.
SAVE THESE INSTRUCTIONS
This manual contains important safety and operating
instructions. Read all instructions and follow them with
use of this product
4
5
9
10
12
13
3
TABLE OF CONTENTS
TM
TM
TECHNICAL SPECIFICATIONS
The term “power tool” in the warnings refers to your mains operated (corded) power
tool or battery operated (cordless) power tool.
CHARGER INPUT
OUTPUT
CHARGING TIMES
WORK AREA
COMPATIBLE
MAXIMUM® BATTERIES
OPTIMUM CHARGING
TEMPERATURE
WEIGHT
100–240V AC, 50/60HZ, 110W
12–20V DC, 4 A
12V max* (1.5Ah) Li-ion: 25minutes
20V max* (2.0Ah) Li-ion (054-3203-2): 35minutes
20V max* (4.0Ah) Li-ion (054-3206-6): 65minutes
•
Keep the work area clean and well lit. Cluttered and dark areas invite accidents.
•
Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks, which may ignite
12V max*(1.5Ah) LITHIUM-ION
054-3203-2,20V max*(2.0Ah) LITHIUM-ION
054-3206-6,20V max*(4.0Ah) LITHIUM-ION
•
50 to 86°F (10 to 30°C)
ELECTRICAL SAFETY
1 lb 8 oz (0.66 KG)
•
the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adaptor plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce the risk of electric shock.
*Maximum battery voltage (12V max* and 20V max*) without workload; with workload
nominal voltage is 10.8 and 18V.
•
Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
•
Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
•
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep the cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
•
When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
•
If operating a power tool in a damp location is unavoidable, use a ground-fault
circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of
electric shock.
PERSONAL SAFETY
•
Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
•
Use personal protective equipment. Always wear eye protection. Protective
equipment such as a dust mask, nonskid safety shoes, hard hat, or hearing
protection, used for appropriate conditions, will reduce personal injuries.
WARNING!
Read all safety warnings and instructions.
5
SAFETY INSTRUCTIONS
TECHNICAL SPECIFICATIONS
4
model no. 054-3204-0 | contact us 1-888-670-6682
•
Prevent unintentional starting. Ensure that the switch is in the off- position
before connecting to a power source and/or battery pack, picking up
or carrying the tool. Carrying power tools with your finger on the switch or
SAFETY INSTRUCTIONS
energizing power tools that have the switch on invites accidents.
•
Remove any adjusting key or wrench before turning the power tool on. A
TM
another battery pack.
•
Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
•
•
•
If devices are provided for the connection of dust-extraction and collection
facilities, ensure that these are connected and properly used. Use of these
When a battery pack is not in use, keep it away from other metal objects, such
as paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
•
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothing, jewelry or long hair can be
caught in moving parts.
Use power tools only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
•
Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may cause
irritation or burns.
SERVICE
•
devices can reduce dust-related hazards.
Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
POWER TOOL USE AND CARE
SPECIFIC SAFETY RULES FOR LITHIUM-ION CHARGER
•
•
Before using the battery charger, read all instructions and cautionary markings in
this manual and on the battery charger. Also read all the instructions in the manuals
for and the cautionary markings on the battery and the product using the battery to
prevent misuse of the products and possible injury or damage.
Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and more safely at the rate for which
it was designed.
•
Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
•
•
Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power
Do not use the charger outdoors or expose it to wet or damp conditions. Water
entering the charger will increase the risk of electric shock.
•
Use of an attachment not recommended or sold by the battery- charger
manufacturer may result in a risk of fire, electric shock or injury to persons.
tool accidentally.
•
Do not abuse the cord or charger. Never use the cord to carry the charger. Do not
pull the charger cord to disconnect the plug from a receptacle. Damage to the cord
or charger could occur and create an electric shock hazard. Replace damaged cords
immediately.
•
Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
•
Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
•
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
•
Use the power tool, accessories, tool bits, etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
BATTERY TOOL USE AND CARE
•
Recharge only with the charger specified by the manufacturer. A charger that
is suitable for one type of battery pack may create a risk of fire when used with
7
CAUTION!
To reduce the risk of electric shock or damage to the
charger and battery, charge only those rechargeable
batteries specifically designated on your charger’s label.
Other types of batteries may burst, causing personal injury
or damage.
WARNING!
Read and understand all instructions. Failure to follow all
instructions listed below may result in electric shock, fire,
and/or serious personal injury.
SAFETY INSTRUCTIONS
6
model no. 054-3204-0 | contact us 1-888-670-6682
SAFETY INSTRUCTIONS
•
9
TM
Make sure that the cord is located so that it will not be stepped on, tripped over,
come in contact with sharp edges or moving parts, or otherwise subjected to
damage or stress. This will reduce the risk of accidental falls, which could cause
injury and damage to the cord, which could then result in electric shock.
•
Keep the cord and charger away from heat to prevent damage to the housing or
internal parts.
•
Do not allow gasoline, oils, petroleum-based products, etc. to come in contact
with plastic parts. These materials contain chemicals that can damage, weaken, or
destroy plastic.
•
An extension cord should not be used unless absolutely necessary. Use of an
improper extension cord could result in a risk of fire and electric shock. If an
extension cord must be used, make sure that:
•
The pins on the plug of extension cord are the same number, size and shape as
those of the plug on charger.
•
The cord is properly wired and in good electrical condition.
The size is large enough for AC ampere rating of charger as specified below:
CORD LENGTH (FEET)
25 FT.
50 FT.
100 FT.
CORD SIZE (AWG)
16
16
16
AWG = American Wire Gauge
•
Do not operate the charger with a damaged cord or plug, which could cause
shorting and electric shock. If damaged, have the charger repaired or replaced by
an authorized service technician.
•
Do not operate the charger if it has received a sharp blow, been dropped, or has
otherwise been damaged in any way. Take it to an authorized service technician for
an electrical check to determine if the charger is in good working order.
•
Do not disassemble the charger. Take it to an authorized service technician when
service or repair is required. Incorrect reassembly may result in a risk of electric
shock or fire.
•
Unplug the charger from the electrical outlet before attempting any maintenance or
cleaning to reduce the risk of electric shock.
•
Disconnect charger from the power supply when not in use. This will reduce the
risk of electric shock or damage to the charger if metal items should fall into the
opening. It will also help prevent damage to the charger during a power surge.
•
Risk of electric shock. Do not touch the uninsulated portion of output connector or
uninsulated battery terminal.
•
Save these instructions. Refer to them frequently and use them to instruct others
who may use this tool. If you loan this tool to someone else, ensure they resd these
instructions to prevent misuse of the product and possible injury.
NO.
DESCRIPTION
1
2
3
4
CHARGING INDICATORS
AIR VENTS
ELECTRIC CONTACTS
DETACHABLE CABLE & PLUG
2
1
3
4
WARNING!
Remove the product and any accessories from the
package. Inspect the tool carefully to make sure no
breakage or damage occurred during shipping.
Do not discard the carton or any packaging material until
all parts have been examined.
KEY PARTS DIAGRAM
8
model no. 054-3204-0 | contact us 1-888-670-6682
TM
Before attempting to use the charger, familiarize yourself with all of its operating
features and safety requirements.
CHARGER DIAGNOSTICS
BATTERY CHARGING
•
When the charger detects a battery pack that is overheated, all three charging
lights will blink at the same time. Please remove the battery and allow it to cool
down for 15–30 minutes and re-insert.
•
When the charger detects a malfunction in the battery, two charging lights will
blink at the same time. Please remove the battery and allow it to cool down for
15–30 minutes. Then re-insert the battery pack into the charger. If two charging
lights still flash, the battery may require service.
•
When the charger detects a malfunction of the charger itself, three charging lights
will blink at the same time. Please remove the battery pack and unplug the charger
for at least 2 minutes. After 2 minutes, plug charger back in and re-insert the pack
into the charger. If all three charging lights still blink at the same time, the charger
may require service.
•
Before attempting to charge the battery, check the charger and the battery to
ensure the charging equipment matches the battery supplied. The components are
all labelled with component numbers.
•
The rechargeable battery is not fully charged on leaving the factory. Charge the
rechargeable battery before first use.
•
Recharge discharged batteries as soon as possible after use or battery life may be
greatly diminished. For longest battery life, do not discharge batteries fully.
•
A fully discharged battery pack will charge about 25–65 minutes, depending on the
type. Charging times maybe longer depending on the surrounding temperature and
battery conditions.
•
The working temperature of the charger is 32–113°F (0–45°C).
CHARGING PROCEDURE
•
Connect the plug cable to the charger, and then plug into
an appropriate outlet before inserting battery pack. All
three charging lights will be on for two seconds and then
off. (Fig. 1)
•
Insert the battery pack into the charger, making sure the
pack is fully seated in the charger. (Fig. 2) During the
charging process, the charging lights will indicate the
charging status as follows:
-
Less than 30% charged: all three charging lights will blink
in sequence.
-
Less than 60% charged: one light will stay on, while the
other two lights will blink in sequence.
-
Over 60% charged: two lights will stay on, while the
remaining light will blink continuously.
-
Fully charged: all three lights will remain on continuously.
WARNING!
Do not allow familiarity with the charger to cause
carelessness. Remember that one careless moment is enough
to cause severe injury. Before attempting to use any tool, be
sure to become familiar with all of the operating features and
safety instructions.
The charger is designed to detect certain problems that can arise with battery packs.
11
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
10
model no. 054-3204-0 | contact us 1-888-670-6682
GENERAL MAINTENANCE
3-YEAR BATTERY/CHARGER REPAIR WARRANTY
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to
damage from various types of commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
Maximum Canada will repair or replace the batteries/chargers which have worn beyond
reasonable use due to normal use of such items, for a period of three (3) years from the
date of original purchase.
MAINTENANCE AND STORAGE
Store your charger in a cool, dry place. As a general practice, it is best to unplug
battery chargers and remove battery packs when not in use.
CLEANING
MAINTENANCE
TM
Before cleaning or performing any maintenance, remove the battery pack from the
tool. For safe and proper operation, always keep the tool and its ventilation slots clean.
Always use only a soft, dry cloth to clean your charger; never use any detergent or
alcohol.
Any defects with such battery and/or charger will be subject to repair or
replacement as determined by the Service Provider. For proper servicing,
both the battery and charger will require diagnosis to evaluate warranty
requirements and therefore must both be provided to the Service Provider
at the time of service request.
The following is excluded from this 3-Year Battery/Charger Repair Warranty:
a) Damages that are a result of abuse or misuse
b) Any wear and tear that does not affect the core function of the product.
b) Any wear and tear that does not affect the core function of the product.
WARNING!
To reduce the risk of injury, always unplug the charger
and remove the battery pack from the charger before
performing any maintenance. Never disassemble the
battery charger.
To reduce the risk of injury and damage, never immerse
your battery charger in liquid or allow a liquid to flow
inside it.
13
WARRANTY
12
model no. 054-3204-0 | contact us 1-888-670-6682
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising