Owner`s Manual TSD-HF11 1x1 Paging Horn Crossover

Owner`s Manual TSD-HF11 1x1 Paging Horn Crossover
Owner’s Manual
TSD-HF11
1x1 Paging Horn Crossover and Limiter
TSD-HF11
1x1 Paging Horn Crossover
and Limiter
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–1–
Specifications are subject to change without notice.
AtlasIED.com
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Owner’s Manual
Description
The AtlasIED Time Saving Device model TSD-HF11 is designed for audio applications that utilize
paging horns and require maximum protection from being overdriven. The TSD-HF11 features a 1
Input and 1 Output configuration and includes Input and Output level controls, balanced Phoenix
and unbalanced RCA input and outputs, selectable hi-pass filters, a contoured low-pass filter, and a
variable output limiter.
The TSD-HF11 can be used with a variety of paging horns and amplifiers. The wide selection of
protection settings allows the user to customize a paging system to achieve maximum performance
while also achieving the protection level required.
The TSD-HF11 is part of a full line of AtlasIED Time Saving Devices. These compact
(1.5" x 4" x 2.5") units are designed to solve some of the common audio system problems in the easiest,
most efficient, and cost-effective way. All models are made from high quality components and
include removable individual I/O connectors for quick and precise wiring, separate ground terminals
for all I/Os assuring secured connections, and removable level controls that can be replaced with
tamper-resistant security covers. The TSDs are highly efficient and meet most energy standards as
one 24V DC power supply (available separately) can power multiple Atlas Time Saving Devices.
Features
Audio Applications
• Balanced Line Input & Output
• Unbalanced RCA Input & Output
• Selectable Low Cut Filers 200Hz, 300Hz, 400Hz
• Fixed 15KHz Hi-Cut Filter
• All Pass Frequency Mode
• High Gain Balanced Line Output for Long Distance Applications
• Input Signal Indicator LED
• Input Limiter Indicator LED
• Separate Ground Connections
• Security Covers Included for All Front Panel Controls
• Cable Management System
•Multiple Mounting Configurations
• Removable Phoenix Style I/O Connectors
• Meets Most Energy Standards
• Compact Chassis Design
• Line Limiter
•Pre-amps
Installation
•Restaurants
• Sports Complexes
•Schools
• Industrial Facilities
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
–2–
Specifications are subject to change without notice.
Owner’s Manual
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Front Panel Description
4
3
2
1
5
6
1. Power LED - Illuminates Blue when 24VDC power is present.
2. Signal LED - Illuminates Green when the input signal strength reaches 25mV to verify a signal path. Note: The LED will not illuminate if the input level is turned Off.
3. Input Peak LED - Illuminates Red when the input signal reaches -3dBV before clipping. Occasional flashing is normal but if this indicator is continuously On, then reduce the input level using the input level control on the front panel.
4. Limiter LED - Adjustment of the Limiter feature should be done after the input gain has been properly set. The input should be adjusted so the Input Peak LED just flashes on signal peaks. Next, adjust the Input Limiter control so the Limiter LED just flashes, indicating that the limiter circuit is active.
5. Input Level Control - Adjusts how much audio signal is applied to the input circuitry. Turn clockwise to increase the signal level and counter-clockwise to decrease it. Note: The Input Level Control knobs can be removed and replaced with supplied security covers to prevent unauthorized adjustment.
6. Output Level Control - Adjusts the amount of signal at the output. Turn clockwise to increase the output level and counter-clockwise to decrease it. Note: The Output Level Control knobs can be removed and replaced with supplied security covers to prevent unauthorized adjustment.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–3–
Specifications are subject to change without notice.
AtlasIED.com
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Owner’s Manual
Rear Panel Description
7
7
7
7
1
2
3
6
4
5
TSD Input/Output connections are removable for easy system wiring. The connectors have a 3.5mm
pitch between pins.
1. DC Power Input - Each TSD that requires DC power comes with a 2 position connector for an external 24VDC power supply (sold separately). Because of the TSD’s low power consumption, a
single external power supply may power more than one TSD. Please refer to the specifications on current requirements in milliamps to match with the appropriate power supply. Please observe
the polarity of the wiring to this connector. Note: It is acceptable to exceed the current
requirements of the TSDs but NOT safe to use a power supply that is below the current requirement of the device.
2. Balanced Line Input - Balanced Line level signals are connected to this input. Your source connections must be mated properly to the input connector or signal loss and/or noise may be introduced. Note: Unbalanced Line level inputs can be inserted by using the following wire configuration, connect the (G) and (-) terminals together.
3. Balanced Line Output - Balanced Line level signals are present on this output when an input
signal is present at the input. Your output connections must be connected properly to the connectors or signal loss and/or noise may be introduced to “upstream” devices.
Note: Unbalanced Line level outputs can be configured by using the following wire configuration, connect the (G) and (-) terminals together.
4. RCA Line Input - Unbalanced Line level signals are connected to this RCA input. Your source connections must be mated properly to the input connector or signal loss and/or noise may be introduced.
5. RCA Line Output - Unbalanced Line level Output signals are present on this RCA Output.
6. Input Limiter Control - This control knob adjusts where the Limiter circuitry starts to reduce the Output Level and must be carefully set. Rotate clockwise to make the limiter more sensitive to input audio signals, thus reducing the Output levels. Rotate counterclockwise to reduce the sensitivity, thus letting larger signal “Peaks” through to the output of the TSD-HF11. See also “Limiter LED” in the previous section for setup instructions.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
–4–
Specifications are subject to change without notice.
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Owner’s Manual
7. Cable Management Retainer Points - Each TSD includes two cable retainer straps for securing
the included cable management retainers. Remove one of the rear panel screws, align the panel hole with a retainer and firmly tighten the screws.
Dip Switch Function Identification
1
2
3
4
LOW CUT
200Hz
300Hz
400Hz
ALL
PASS
OFF
OFF
OFF
OFF
ON
ON
ON
ON
Switch Position
• Dip Switch # 1 - 200Hz Low Cut, place switch in the down position to activate the filter.
• Dip Switch # 2 - 300Hz Low Cut, place switch in the down position to activate the filter.
• Dip Switch # 3 - 400Hz Low Cut, place switch in the down position to activate the filter.
• Dip Switch # 4 - All Pass - No Hi Cut filter is active when the switch is placed in the down position.
Note: Hi Cut 15KHZ filter is always active.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–5–
Specifications are subject to change without notice.
AtlasIED.com
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Owner’s Manual
Cable Management
Knob and Security Cover
All front panel level controls feature a removable knob that can be replaced with an included security
cover. Follow these steps to prevent potentiometer damage or unwanted changes.
1. Knob Installation - Turn the potentiometer shaft fully counter-clockwise. Align the knob indicator to the lowest setting on the panel and the potentiometer shaft slot. Carefully press the knob onto
the potentiometer shaft. Do not force or damage may occur to the potentiometer.
2. Security Cover Installation - Remove the knob from the panel and insert the cover. Small pliers may be required to remove the knobs. Align the security cover to the level control panel hole. Push the cover into the hole until it snaps into place. Do not force or damage may occur to the potentiometer.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
–6–
Specifications are subject to change without notice.
Owner’s Manual
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Mounting
Listed below are the ways to mount the TSD and the optional accessories that can be purchased.
1.Velcro™ - Each unit includes two 2" x 2" pieces of industrial-grade Velcro™ with adhesive backing to adhere to any flat surface. Clean all surfaces before applying the adhesive side of the Velcro™.
2. Multi Mount Plate - Each TSD includes a versatile multi-position mounting plate. This plate allows the TSD to be mounted to any surface; but is ideal for use with rear rack rails or side rack hat channels. Use the included M3 x 4mm screws to install the plate on the TSD. Note: Only use the included M3 x 4mm screws as other screws may be too long and will cause internal damage to the TSD. The multi-position mounting plate is a new addition being included with TSDs. If the TSD being used did not include the mounting plate, contact AtlasIED customer service at
1-800-876-3333.
(M3 x 4mm)
(M3 x 4mm)
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–7–
Specifications are subject to change without notice.
AtlasIED.com
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Owner’s Manual
Optional Mounting Accessories
1. TSD-RMK 19" Width Rack Mount Kit - For 19" rack mounting, AtlasIED offers an optional rack mount kit, the TSD-RMK. This rack mount kit can support up to four TSD units. The kit includes three blank panels designed to fill any unused slots. Use the included hardware to mount the TSD into the rack mount kit using the top mount screw holes on the TSD.
2. TSD-RMKHR Half Width Rack Mount Kit - AtlasIED offers an optional rack mount kit that can be used in half width rack applications including the AtlasIED WMA-HR and AWR-HR models. The TSD-RMKHR can support up to two TSDs. Included is an extra blank panel to fill one of the spaces if only one TSD is being used.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
–8–
Specifications are subject to change without notice.
Owner’s Manual
TSD-HF11
1x1 Paging Horn Crossover and Limiter
3. TSD-RRMK Rear Rack Mounting Kit - For complete flexibility in mounting a TSD or TSD external power supplies the optional TSD-RRMK is available. The TSD-RRMK can support mounting of either two larger TSDs with external power supplies or up to 4 TSD models. Note: Only use the included M3 x 4mm screws as other screws may be too long and will cause internal damage to
the TSD.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
–9–
Specifications are subject to change without notice.
AtlasIED.com
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Owner’s Manual
POWER
LED
+24V
POWER
RCA OUT
200Hz
15KHz
300Hz
ON
ON
ON
ON
400Hz
OFF
OFF
OFF
OFF
4
ALL
PASS
2
1
PEAK
LED
SIGNAL
LED
LIMITER
LED
G
–
+
INPUT
RCA IN
MASTER
LIMITER
LIMITER
THRESHOLD
1 2 3 4
LOW CUT
3
400Hz
300Hz
200Hz
FULL FREQ.
OUTPUT
GAIN
–
G
+
OUTPUT
Block Diagram
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
– 10 –
Specifications are subject to change without notice.
Owner’s Manual
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Specifications
Description
1 x 1 Paging Horn Crossover and Limiter
Chassis Color
Chassis Material
Black
Aluminum
Inputs
Type
Qty 1, Unbalanced
ConnectionRCA
Impedance10kΩ
Input Level
316mV (-10dBV) = 1V (0dBV) Unbalanced RCA Output,
Maximum Input 3V (9.5dBV)
Type
Qty 1, Balanced Line
Connection
Removable 3 Position Captive Screw 3.5mm Spacing
Impedance10kΩ Balanced
Line Input Level
1V (0dBV) Balanced = 2V (+6dBV) Balanced Output,
Maximum Input 6V (15.5dBV)
Outputs
Type
Qty 1, Unbalanced
ConnectionRCA
Impedance150Ω
Input Level
316mV (-10dBV) RCA Input = 1V (0dBV) RCA Output,
Maximum Output 7V (16.9dBV)
Type
Qty 1, Balanced Line
Connection
Removable 3 Position Captive Screw 3.5mm Spacing
Impedance300Ω Balanced
Line Input Level
1V (0dBV) Balanced Input = 2V (+6dBV) Balanced Output,
Maximum Output 12.5V (17dBV)
Controls
Input Level Control Output Level Control Input Limiter
Qty 1, Removable Knob with Security Cover
Qty 1, Removable Knob with Security Cover
Threshold Adjust
Dip Switch Function
Dip Switch # 1
Dip Switch # 2
Dip Switch # 3
Dip Switch # 4
200Hz Hi Cut / 18dB
300Hz Hi Cut / 18dB
400Hz Hi Cut / 18dB
All Pass
Indicators
Input Signal
Input Peak
Limiter Power Green, 25mV ON Threshold, Qty 1
Red, -3dB Before Clip, Qty 1
Yellow, Limiter Activation, Qty 1
Blue, Qty 1
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
– 11 –
Specifications are subject to change without notice.
AtlasIED.com
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Owner’s Manual
Electrical
Frequency Response THD Noise, Maximum Input Limiter
Related to Dip Switch Settings, All References -3dB,
Filters 18dB per Octave
• 200Hz - 15KHz
• 300Hz - 15KHz
• 400Hz - 15KHz
• All Pass - 20Hz - 15KHz
.06% @ 1kHz
450uV (-99dBV)
Hard Limiter Potentiometer Position
• FCCW 0dB = 0dB
• 12 O’clock = - 4dB +/-1dB
• FCW –dB = -8dB
Power Requirements
Voltage
Power Consumption VA Watts
24VDC, 35mA, Removable 2 Position Phoenix
1.6W
Dimensions
H 1.5" (39mm) x W 4" (101mm) x D 2.5" (70mm)
Weight
6oz, .165kg
Included Accessories
Velcro™Industrial-Grade
Multi-Mount Plate
Qty 1, Includes Two (2) M3 x 4mm Screws
Cable Retainers
Qty 2
Level Control Knobs
Qty 2
Level Control Security Covers Qty 2
Optional Accessories
TSD 24VDC
TSD-RMK
TSD-RMKHR
TSD-RRMK
Power Supply
1 RU 19" Width Rack Mount Panel (Supports 4 TSD Units)
1 RU Half Rack Width Panel (Supports 2 TSD Units)
Rear Rack Mounting Kit
Safety and Certifications
External Power Supply
cUL, CE, RoHS, TUV
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
– 12 –
Specifications are subject to change without notice.
Owner’s Manual
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Notes:
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
– 13 –
Specifications are subject to change without notice.
AtlasIED.com
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Owner’s Manual
Notes:
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
– 14 –
Specifications are subject to change without notice.
Owner’s Manual
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Notes:
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
– 15 –
Specifications are subject to change without notice.
AtlasIED.com
TSD-HF11
1x1 Paging Horn Crossover and Limiter
Owner’s Manual
Limited Warranty
All products manufactured by AtlasIED are warranted to the original dealer/installer, industrial or
commercial purchaser to be free from defects in material and workmanship and to be in compliance
with our published specifications, if any. This warranty shall extend from the date of purchase for
a period of three years on all AtlasIED products, including SOUNDOLIER brand, and ATLAS SOUND
brand products except as follows: one year on electronics and control systems; one year on
replacement parts; and one year on Musician Series stands and related accessories. Additionally,
fuses and lamps carry no warranty. AtlasIED will solely at its discretion, replace at no charge or
repair free of charge defective parts or products when the product has been applied and used in
accordance with our published operation and installation instructions. We will not be responsible
for defects caused by improper storage, misuse (including failure to provide reasonable and
necessary maintenance), accident, abnormal atmospheres, water immersion, lightning discharge,
or malfunctions when products have been modified or operated in excess of rated power, altered,
serviced or installed in other than a workman like manner. The original sales invoice should be
retained as evidence of purchase under the terms of this warranty. All warranty returns must comply
with our returns policy set forth below. When products returned to AtlasIED do not qualify for repair
or replacement under our warranty, repairs may be performed at prevailing costs for material and
labor unless there is included with the returned product(s) a written request for an estimate of repair
costs before any nonwarranty work is performed. In the event of replacement or upon completion of
repairs, return shipment will be made with the transportation charges collect.
EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF CONSEQUENTIAL
DAMAGES FOR PERSONAL INJURY, ATLASIED SHALL NOT BE LIABLE IN TORT OR CONTRACT
FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE ARISING OUT OF THE
INSTALLATION, USE OR INABILITY TO USE THE PRODUCTS. THE ABOVE WARRANTY IS IN LIEU OF
ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
AtlasIED does not assume, or does it authorize any other person to assume or extend on its behalf,
any other warranty, obligation, or liability. This warranty gives you specific legal rights and you may
have other rights which vary from state to state.
Service
Should your Atlas TSD require service, please contact the AtlasIED
warranty department at 1-877-689-8055, ext. 277 to obtain an RA number.
AtlasIED Tech Support can be reached at 1-800-876-3333 or support.atlasied.com.
Visit our website at www.AtlasIED.com to see other Atlas products.
©2017 Atlas Sound L.P. The Atlas “Circle A”, Soundolier, and Atlas Sound are trademarks of Atlas Sound L.P.
IED is a registered trademark of Innovative Electronic Designs LLC. All Rights Reserved.
All other trademarks are the property of their respective owners. All specs are subject to change without notice. ATS004727 RevB 4/17
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
AtlasIED.com
– 16 –
Specifications are subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising