Step-By-Step Installation Instructions

Step-By-Step Installation Instructions
Interceptor
Accelerator
Controller
Interceptor Controller
MAP
Harness
Connector
MAP
Sensor
Connector
Intake Air Temp
Sensor Connector
Cam
Harness
Connector
Cam
Sensor
Connector
Intake Air Temp
Harness Connector
Pedal
Sensor
Connector
Pedal
Harness
Connector
Step-By-Step
Installation Instructions
Hypertech’s new product, the Interceptor, is a
smart technology design that works with today’s
generation of complex engine computers.
The Interceptor easily mounts under the hood of a
vehicle and plugs into the factory connectors to
constantly monitor the vehicle’s functions. It then
automatically recalculates the factory’s computer
performance calibrations with legendary
Hypertech Power Tuning. This means more
horsepower and torque, quicker acceleration, better
driveability, and improved MPG.
Underhood sensor locations for installing the Hypertech™ Interceptor ™
MAP Sensor
The Interceptor Controller easily installs under the
hood in about fifteen (15) minutes. The Interceptor
Accelerator Pedal Controller installs in the vehicle’s
interior on the driver’s side above the accelerator
pedal in about (15) minutes.
Intake Air
Temp Sensor*
Cam Sensor
BEFORE installing the Hypertech Interceptor:
Make sure the vehicle engine and ignition is turned
OFF prior to beginning the installation.
* NOTE:
Tools needed for Interceptor installation:
• Flashlight
• Flathead screwdriver (Ram Trucks/Dodge SUVs ONLY)
• 8mm socket and ratchet (Ram Trucks/Dodge SUVs ONLY)
Sensor locations may vary slightly depending on the application.
Installing the Hypertech Interceptor Controller
Connecting the Cam Sensor
Cam Sensor
Locate fuse box in the engine compartment on the passenger side.
Press the locking tabs to disengage fuse box and lift up to expose
empty compartment.
Route the Interceptor wire to the cam sensor. Disconnect the
factory harness from the cam sensor.
Vehicle Cam
Sensor
Interceptor Cam
Sensor Connector
Interceptor
Controller
Plug the Interceptor cam sensor connector into the vehicle cam sensor.
Place Interceptor Controller on its side in the compartment. Then
re-install the fuse box back to its original location.
Interceptor
Harness
Connector
Before proceeding to the next three (3) installation sections, lay out the
Interceptor harness in the general areas of the sensor locations as shown
in the engine compartment photo on page 1.
Factory Cam
Sensor Wiring
Harness Connector
Plug the Interceptor harness connector into the factory cam sensor
wiring harness connector.
NOTE: Ensure that the Interceptor harness and all connectors are clear
from moving and/or rotating parts of the engine as well as any extreme
heat sources.
2
Connecting the MAP Sensor
Connecting the MAP Sensor (Cont’d)
Factory MAP
Wiring Harness
Connector
Interceptor
Harness
Connector
Lift off the engine cover (passenger side on SRT-8). NOTE for Ram
Truck Specific: Disconnect the Intake Air Temp sensor. Then, using a
flathead screwdriver or 8mm socket, loosen the clamp at the throttle body
and lift the intake hose out of the way. Then remove the engine cover.
Fuel Injector
Harness
Plug the Interceptor harness connector into the factory MAP wiring
harness connector, and push in the locking clip. NOTE for Ram Truck
Specific: Reposition the intake hose and use an 8mm socket to tighten the
clamp at the throttle body.
NOTE: Ensure that the Interceptor harness and all connectors are clear
from moving and/or rotating parts of the engine as well as any extreme
heat sources.
Connecting the Intake Air Temp Sensor
Interceptor MAP
Sensor Wire
To Vehicle
Intake Air Temp
Sensor
Route the Interceptor MAP sensor harness under the fuel injector
harness to the MAP sensor.
Disconnect the factory connector from the MAP sensor. This
connector has a locking clip that must be slid back to unlock.
Then, squeeze down the locking tab, and push the connector in
slightly (toward sensor) and then remove.
Route the Interceptor wire to vehicle intake air temp sensor.
Disconnect the factory harness from the Intake air temp sensor.
Vehicle Intake
Air Temp Sensor
Vehicle MAP
Sensor
Interceptor MAP
Sensor Connector
3
Plug the Interceptor MAP sensor connector into the vehicle
MAP sensor.
Interceptor Intake
Air Temp Connector
Plug the Interceptor intake air temp sensor connector into the
vehicle intake air temp sensor.
Connecting the Intake Air Temp Sensor (Cont’d)
Interceptor
Harness
Connector
Connecting the Interceptor Accelerator Controller (Cont’d)
Factory Accelerator
Pedal Sensor
Connector
Factory Intake
Air Temp Sensor
Wiring Harness
Connector
Plug the Interceptor harness connector into the factory intake air
temp sensor wiring harness connector.
NOTE: Ensure that the Interceptor harness and all connectors are clear
from moving and/or rotating parts of the engine as well as any extreme
heat sources.
Connecting the Interceptor Accelerator Controller
Interceptor
Accelerator
Pedal Harness
Connector
Plug the Interceptor accelerator pedal harness connector into the
vehicle’s factory accelerator pedal sensor connector.
Tuck the Interceptor accelerator controller behind the carpet and out of
the way. You may secure it using a zip tie. Installation is now complete!
You are now ready to enjoy more power and performance with the
Hypertech Interceptor!
Factory
Accelerator
Harness
Connector
(Behind Carpet)
Using a flashlight, locate the factory accelerator harness connector
under the driver’s dashboard and above the accelerator pedal.
Push the carpeted compartment cover out of the way so you can
disconnect the factory harness from the accelerator pedal sensor.
Interceptor
Accelerator
Pedal Sensor
Connector
Factory
Accelerator
Pedal Sensor
Plug the Interceptor accelerator pedal sensor connector into the
factory accelerator pedal sensor.
30-Day Risk-Free, Money Back Guarantee
The 30-day money back guarantee applies to the
Interceptor, Max Energy Power Programmer, E-CON
Economy Power Programmer, and the Speedometer
Calibrator. The product MUST be returned to the place of
purchase within 30 days. All items must be received in a
new, unused and ready-to-sell condition (including all
original packaging, parts, and paperwork) to receive a
refund, excluding any shipping and handling fees.
Product Warranty
Factory Direct Limited Lifetime Warranty
All Hypertech Power Tuning Products are warranted* against defects in
materials or workmanship. Hypertech’s liability under this warranty shall be
limited to the prompt correction or replacement of any defective part of the
product which Hypertech, Inc. determines to be necessary. This Limited
Lifetime Warranty is to the original purchaser for as long as he or she owns
the vehicle on which the product is originally installed, providing all the
information requested is furnished. You must retain a copy of your original sales
invoice or receipt. Without proper documentation, a service fee will be applied.
Resold units are NOT covered under this warranty.
* Power Tuning products are Interceptors, Max Energy Power Programmers, E-CON Economy Power
Programmers, Speedometer Calibrators, Power Tuning Modules, Power Chips, and Power Modules.
Accessories such as Power caps, Power Coil kits, and fuel pressure regulators have a one (1) year warranty.
3215 Appling Road • Bartlett, Tennessee 38133-3999
Office Hours: 8am - 5pm, Central Time, Mon. - Fri.
Tech: 901.382.8888 • Business: 901.385.1888 • Fax: 901.373.5290
For more information, go to www.hypertech.com
Part #827
1.13
© 2013 Hypertech, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising