Quick Specs - Products
GTX65EBSJ
GE Appliances 6.1 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer with HE Sensor Dry
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRIC DRYER RATING:
240V
5600W
24A
208V
4400W
22A
22 1/2"
27 3/4"
27"
26"
Power Cord 4 1/2"
11 3/4"
60Hz
60Hz
EXHAUST OPTION: 4-way rear, right, left and bottom.
CIRCUIT REQUIREMENTS: An individual, properly-grounded branch circuit,
protected by a 30-amp circuit breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be located within 36" of service cord entry and
acessible when dryer is mounted in position.
46"
37 1/2"
INSTALLATION INFORMATION: For complete information, see installation
instructions packed with your dryer.
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the
dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces5.7
are:cu.
0" ft. Dryers
either side; 1" front, top and rear.
2
- Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60
sq. in. of open area equally distributed. If this closet contains both a washer and a dryer,
doors must contain a minimum of 120 sq. in. of open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
Power
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes,Cord
withHole
30-1/2
the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
- Minimum clearances to combustible surfaces are: 0" both sides; 1" rear.
DRYER EXHAUSTING INFORMATION­:
Back View
- Use metal duct only, vertical and horizontal ducting.
4 1/4"
1 3/4"
4"
5"
3 1/4"
Rear View
REAR
VIEW
View
SIDESide
VIEW
5.8,
6.0 and
7.0
cu. ft. Dryers
POWER
CORD
LOCATIONS
5
Power
Cord Hole
4-1/2
BACK
BackVIEW
View
Listed by
Underwriters
Laboratories
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 9/16
GE Dryer Vent
GTX65EBSJ
GE Appliances 6.1 Cu. Ft. Capacity Aluminized Alloy Drum
Electric Dryer with HE Sensor Dry
FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED WITH
YOUR DRYER.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct.
If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used
(Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house
vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used
ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used
AND where a 4" diameter can be maintained throughout the entire length of the transition duct.
Please see installation instruction packed with your dryer for complete instructions when using
flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or
bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown
in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should
be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
GE Dryer Vent
DRYER EXHAUSTING INFORMATION—
USE METAL DUCT ONLY VERTICAL AND
HORIZONTAL DUCTING
BEST PERFORMANCE
Maximum length
of 4" dia rigid
A 4
metal duct
B
Exhaust hood type
A
Number
A
B
of 90°
4"
2-1/2"
4
2-1/2
Domestic dryer
turns
opening opening
B models
0
120 ft.
90 ft.
1
100 ft.
75 ft.
2-1/2
Long Vent 6.1-7.4 cu. ft.
2
85 ft.
65 ft.
capacity electric & gas
3
70 ft.
55 ft.
(GTD33, GTD42, GTD45,
4
60 ft.
45 ft.
GTD65, GTX22, GTX33, GTX42
and GTX65)
5
55 ft.
35 ft.
A
For every extra 90° elbow, reduce the allowable vent system
length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
When calculating the total vent system length, you must add all
the straight portions and elbows of the system (including the
transition duct.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or
moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a
kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting,
etc. The wall cap must also be located at least 12" above the ground or any other obstruction with
the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL
1-800-GE-CARES.
Specification Revised 9/16
GTX65EBSJ
GE Appliances 6.1 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer with HE Sensor Dry
FEATURES AND BENEFITS
ENERGY STAR® qualified – Meets or exceeds federal guidelines for energy efficiency
for year-round energy and money savings
Up to 120-ft. venting capability – Provides flexible installation
Extended Tumble – Tumble clothes without heat to help prevent
creasing and wrinkling
HE Sensor Dry – Keep your clothes looking and feeling their best. Dual thermistors
continually monitor temperature with a sensor bar that measures moisture to prevent
over-drying
Flat Back Design – Makes it easy to install in small areas like closets and utility rooms
where space is limited
My Cycle Settings – Dry clothes with the settings you prefer on any cycle, rather than
the defaults, and store your settings for later use
Damp Alert – Alerts you when clothes are the ideal dampness for ironing, for perfectly
wrinkle-free results
Model GTX65EBSJWS – White with silver backsplash
GTD65EBSJ_GTD65GBSJ
Specification Revised 9/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising