delsol gas grill
DELSOL GAS GRILL
INSTALLATION, USE & CARE MANUAL
Models:
P/N: 18930C
DSBQ25
DSBQ32R
DSBQ40R
A special message…
Congratulations on your purchase of DELSOL gas barbecue grill. DELSOL is
committed to making outdoor cooking products you’ll be proud to own for years.
This manual gives you easy to follow instructions for installing, operating and
maintaining your DELSOL grill. We recommend reading this manual carefully
before your first use to ensure safety, proper care and operation. Keep this manual in
a safe place for future reference.
Thank you and welcome!
DELSOL
____________________________________________________________________
FOR YOUR RECORDS
Please record the following information and refer to them when contacting the
company or an authorized service agent. This information is found on the data
nameplate, located on the rear panel of the grill.
Model #: ________________________________
Serial #: _________________________________
Date of Purchase: __________________________
Place of Purchase: __________________________
Type of Gas:
NG
LP
To the Installer:
Please read these instructions completely before installation and give this manual to the owner.
To the Owner:
Keep this manual in a safe place for future reference.
IMPORTANT SAFETY INFORMATION – DELSOL GAS GRILL
WARNING! Read this manual carefully and completely before using your grill to ensure proper
operation, proper installation, proper servicing and to reduce the risk of fire, burn hazard and/ or
other injury.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open lid.
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or fire department.
WARNING
1. Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
vapors and any liquids in the vicinity of this or
any other appliance
BEFORE LIGHTING
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 4 seconds,
turn the burner control(s) off, wait 5
minutes, and repeat the lighting
procedure.
DANGER
S’il y a une odeur de gaz:
1. Coupez l’admission de gaz de l’appariel.
2. Éteindre toute flamme nue.
3. Ouvrir le couvercle.
4. Si l’odeur continue, évite l’appareil et
appelle tout de suite votre fournisseur de gaz
ou les pompiers.
AVERTISSEMENT
1. Ne pas entreposer ni utiliser de l’essence ni
d’autres vapeurs ou liquides inflammables
dans le voisinage de l’appareil, ni de tout
autre appareil.
2. Une bouteille de propane qui n’est pas
raccordée en vue de son utilisation, ne doit
pas être entreposée dans le voisinage de cet
appareil ou de tout autre appareil.
MESURE DE SECURITE
Ne pas entreposer ni utiliser d’essence ni autres
vapeurs ou liquides inflammables à proximité de
cet appareil ou de tout autre appareil.
AVANT
D’ALLUMER
L’APPAREIL
1. Lisez les instructions avant d’allumer
l’appareil.
2. Ouvrez le couvercle avant d’allumer l’appareil.
3. Si l’appareil ne s’allume pas en 4 secondes,
fermez le robinet du brûleur, attendez 5
minutes, et procédez de nouveau à l’allumage.
THIS GRILL IS FOR OUTDOOR USE ONLY: CE GRIL EST POUR UTILISATION à
L’ExTéRIEUR SEULEMENT:
If stored indoors, detach and leave L.P. cylinder Si l’appareil est entreposé à l’interieur, enlever
outdoors.
les bouteilles et les laisser à l’extérieur.
GENERAL SAFETY REQUIREMENTS:
1. The installation of this appliance must conform with local codes or, in the absence of local codes;
either the National Fuel Gas Code, ANZI Z223.1/NFPA 54, or the CAN/CGA-B149.1, Natural
Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code.
2. This outdoor cooking gas appliance is not intended to be installed in or on recreational vehicles
and /or boats.
3. This outdoor cooking gas appliance is intended for use outdoors and shall not be used in a
building, garage or any other enclosed area.
4. Minimum clearance of 12 inches from the back and sides of the grill to adjacent
combustible construction must be maintained. This outdoor cooking gas appliance shall not
be located under overhead-unprotected combustible construction.
5. The utilization of an external electrical source requires that when installed, this outdoor cooking
gas appliance must be electrically grounded in accordance with the local codes or, in the absence
of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1. Keep any electrical supply cord, or the rotisserie motor cord and the fuel
supply hose away from any heated surfaces.
6. Keep your grill in an area clear and free from combustible materials, gasoline and other
flammable vapors and liquids.
7. DO NOT obstruct the flow of combustion and ventilation air to this appliance. Keep the
ventilation openings of the cylinder enclosure free and clear from debris.
8. Check all gas connections for leaks with soapy water solution and brush. Never use an open
flame. (Reference page 8 for leak test procedure).
9. Check flexible hoses for cuts and wear that may affect the safety before each use.
10. Never use charcoal in the grill.
11. Never use the grill in a windy area.
12. Never use the grill without the drip pan installed and push all the way to the back of the grill.
Without the drip pan, hot grease and debris could leak downward and produce a fire hazard.
13. The pressure regulator and hose assembly supplied with the DELSOL Gas Grill must be used.
Replacement pressure regulators and hose assemblies must be those specified by DELSOL.
14. CALIFORNIA PROPOSITION 65-WARNING: The burning of gas cooking fuel generates some
by-products which are on the list of substances known by the State of California to cause cancer
or reproductive harm. California law requires businesses to warn customers of potential exposure
to such substances. To minimize exposure to these substances always operate this unit according
to the use and care manual, ensuring you provide good ventilation when cooking with gas.
In Massachusetts: All gas products must be installed using a “Massachusetts” licensed plumber or
gasfitter. A “T” handle type manual gas valve must be installed in the gas supply line to this
appliance. This applies to permanently installed Natural Gas and propane installations. This does
not apply to propane portable installations using a 20 pound tank.
TABLE OF CONTENTS – DELSOL GAS GRILL
GETTING STARTED…………………………………………………………………… …..
1
GAS REQUIREMENTS
o GAS SAFETY REQUIREMENT……………………………………………...
3
o LP GAS HOOKUP………….…………………………………………………
4
o PORTABLE LP CONNECTION………….…………………………………..
5
o NATURAL GAS INSTALLATION…………………………………………..
6
o LEAK TEST…………………………………………………………………… 8
BURNER FLAME / AIR SHUTTER ADJUSTMENT...........................................................
9
LOCATING THE GRILL
o CLEARANCE TO COMBUSTIBLE CONSTRUCTION……………………... 10
o CLEARANCE TO NONCOMBUSTIBLE CONSTRUCTION……………..… 10
CUTOUT DIMENSIONS
o GRILL………………………………………………………………………….. 11
ASSEMBLY INSTRUCTIONS
o BRIQUETTE TRAY…………………..……………………………………….. 12
o WARMING RACK……………………………………………………………
12
o ROTISSERIE…………………………...……………………………………… 13
OPERATING INSTRUCTIONS
o BEFORE LIGHTING THE GRILL…………………………………………… 14
o TO LIGHT THE GRILL BURNER ………………………………………….. 14
o MATCH LIGHTING INSTRUCTIONS ……..………………………………
15
o USING THE GRILL …………………………………………………………… 15
o USING THE ROTISSERIE BURNER……………..…………………………….. 16
o GRILLING IN WINDY CONDITION ………………………………………… 17
CLEANING AND MAINTENANCE
o STAINLESS STEEL…………………………………………………………… 18
o COOKING GRATES ………………………………………………………… 18
o CERAMIC BRIQUETTE TRAY….…………………………….………….…
18
o U-BURNER & SEAR ZONE BURNER………………………………………
19
o DRIP PAN ………………….………………………………………………… 19
o SPIDER AND INSECT WARNING…………………………………………… 19
TROUBLE SHOOTING GUIDE…………………...………………………………………… 20
REPLACEMENT PARTS
o EXPLODED VIEW………………………………………….…………………. 21
o REPLACEMENT PARTS LIST…………………………..……………….……. 22
o LIMITED PRODUCT WARRANTY………………………………………...…. 24
o WARRANTY REGISTRATION CARD ………………………………………. 25
GETTING STARTED – DELSOL GAS GRILL
1. Remove all packaging materials, labels and protective plastic film. DO NOT LEAVE UNIT
UNDER THE SUN WITH PROTECTIVE PLASTIC FILM ON FOR A LONG PERIOD OF
TIME AS IT WILL BECOME DIFFICULT TO REMOVE THE FILM.
2. Check to ensure that all grill accessories listed below are included.
DSBQ
25
3
3
1
(1)
1
Grill Accessories
Grate, Stainless Steel
Briquette Tray Assembly
Regulator, NG (NG Grills Only)
Regulator, LP (LP Grill ONLY)
Warming Rack, (s/s)
DSBQ
32R
4
4
1
(1)
1
3. Assemble parts as per assembly instructions on page 12-13.
4. Fill out the Warranty Registration Card and mail it to the indicated address.
1
DSBQ
40R
5
5
1
(1)
1
GETTING STARTED – DELSOL GAS GRILL
5. Get familiar with the knobs and burners identification below.
DSBQ25
DSBQ32R
Grill
Burner
Grill Burner
Rotisserie
Burner
Sear Zone (Opt)
Grill
Burner
DSBQ40R
Grill
Burner
Rotisserie
Burner
Grill
Burner
Infrared Rotisserie Burner located on the rear panel
above the grates.
(32R & 40R Models Only)
Straight Burner (Standard) located underneath the
briquette trays.
2
GAS SAFETY REQUIREMENTS – DELSOL GAS GRILL
Each appliance is set and tested at the factory for the type of gas supply to be used. Identify
the type of gas, either Natural Gas or LP gas and make sure that the marking on the data plate
(rating plate) matches the gas being supplied to the grill. The data plate is located on the rear panel
of the grill.
All gas connections should be made by a qualified technician and in accordance with local
codes and ordinances. The installation must conform with local codes or, in the absence of local
codes, with either the national Fuel Gas Code, ANSI Z223.1/NFPA 54, or CAN/CGA-B149.1,
Natural Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code.
WARNING:
CHECK TO ENSURE THAT THE GAS SUPPLY HOSE DOES NOT COME IN
CONTACT WITH ANY HOT SURFACE OF THE GRILL.
NEVER CONNECT THE GRILL TO AN UNREGULATED GAS SUPPLY.
L.P. GAS (LIQUIFIED PETROLEUM /PROPANE)
If your grill is factory built for L.P., the regulator supplied is set for 11” water column and
is for use with L.P. gas only. The factory-recommended regulator and hose must be used with a 20
lb. L.P. cylinder.
L.P. GAS SAFETY REQUIREMENT
The LP-gas supply cylinder must be constructed and marked in accordance with the
Specifications for LP-gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the
National Standards of Canada CAN/CSA-B339, Cylinders, Spheres and Tubes for the
Transportation of Dangerous Goods, and Commission, as applicable; and
1. Provided with a listed overfilling prevention device.
2. Provided with a cylinder connection device compatible with the connection for outdoor
cooking appliances.
It must be provided with a shut-off valve terminating in gas tank valve outlet. It must include a
collar to protect the cylinder valve. The cylinder supply system must be arranged for vapor
withdrawal.
Do not operate the gas grill indoors or in any enclosed area. If the gas grill is not in use, the gas
must be turned off at the supply cylinder. If the grill is to be stored indoors, disconnect the gas
supply cylinder and leave the cylinder outdoors out of reach of children and must not be stored in a
building, garage or any other enclosed area.
3
LP GAS HOOK-UP – DELSOL GAS GRILL
DELSOL grill for the use of LP gas comes equipped with its own regulator, which MUST NOT
be removed. Install the factory-supplied hose and regulator assembly as shown. Connect the 3/8” flare
end of the hose to the grill coupling using a ¾” open wrench. Do not apply pipe sealant to the 3/8” flare
connection. Connect the regulator to the LP cylinder hand tighten it, do not use a wrench. Check for
leaks using soapy water solution. (Reference page 8 for leak test procedure).
Note: An enclosure for LP gas cylinder must be vented on the level of the cylinder valve and at floor
level. The effectiveness of the opening(s) for purposes of ventilation shall be determined with the LP gas
supply cylinder in place. This shall be accomplished by one of the following:
a. One side of the enclosure shall be fully open; or
b. For an enclosure having four sides, a top and a bottom:
1. At least two ventilation openings at cylinder valve level shall be provided in the sidewall,
equally sized, spaced at 180 degrees (3.14 rad), and unobstructed. Each opening shall
2
have a total free area of not less than 1/2 square inch per pound (7.1 cm /kg) of stored
2
fuel capacity and not less than a total free area of 10 square inches (64.5 cm ).
2. Ventilation opening(s) shall be provided at floor level and shall have a total free area of
2
not less than ½" square inch per pound (7.1 cm /kg) of stored fuel capacity and not less
2
than a total free area of 10 square inches (64.5 cm ). If ventilation openings at floor
level are in a sidewall, there shall be at least two openings. The bottom of the openings
shall be at floor level and the upper edge no more than 5 inches (127 mm) above the
floor. The openings shall be equally sized, spaced at 180 degrees (3.14 rad) and
unobstructed.
! WARNING !
DO NOT STORE SPARE LP-GAS CYLINDER UNDER OR NEAR THIS APPLIANCE.
NEVER FILL THE CYLINDER BEYOND 80 PERCENT FULL.
FAILURE TO DO SO, A FIRE CAUSING DEATH OR SERIOUS INJURY MAY OCCUR.
4
PORTABLE LP CONNECTION – DELSOL GAS GRILL
 NOTE: USE ONLY A 20-LBS. (5-GALLON
CAPACITY) GAS CYLINDER.
 WARNING: DO NOT PLACE MORE THAN ONE
CYLINDER IN THE BASE CABINET ENCLOSURE
AT ANY TIME.
 WARNING: DO NOT USE A DENTED OR RUSTED
LP CYLINDER.
 NEVER USE A CYLINDER WITH A DAMAGED
VALVE.
 ALWAYS CHECK FOR LEAKS AFTER
CHANGING THE LP CYLINDER. (Page 8)
 THE HIGH PRESSURE LP REGULATOR AND
HOSE (SOLD SEPARATELY) MUST BE USED
WITHOUT ALTERATION.
 ALWAYS USE THE TANK SECURING DEVICE
SUPPLIED WITH GRILL BASE AND ENSURE
THAT THE TANK IS SECURED PROPERLY.
DELSOL grill for use of LP gas comes equipped with its
own regulator, which MUST NOT be removed.
1) To install the gas cylinder, place the cylinder onto the
provided cutout.
2) Secure the cylinder with the chain provided. Ensure
that cylinder is firmly secured.
3) Check to ensure that the tank’s gas valve on top of the
cylinder is closed.
4) Connect the 3/8” flare end of the hose to the grill
coupling using a ¾” open wrench. Do not apply pipe
sealant to the 3/8” flare connection.
5) Connect the LP regulator to the cylinder and handtighten only. Open the tank valve and make sure all
connections are leak tight using a soapy water solution
and a brush. (Reference page 8 for leak test
procedure).
5
Convertible Gas
Pressure Regulator
3/8 flare fitting
NATURAL GAS INSTALLATION – DELSOL GAS GRILL
The installation must conform with local codes or, in the absence of local codes, with either the
national Fuel Gas Code, ANSI Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas Installation Code or
CAN/CGA-B149.2, Propane Installation Code.
1. This gas appliance and its individual shutoff valve must be disconnected from the gas supply piping
system during any pressure testing of that system at the test pressures in excess of 1/2 psi (3.5 kPa).
2. This appliance must be isolated from the gas supply piping system by closing its individual manual
shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or
less than 1/2 psi (3.5 kPa).
If the gas grill is factory built for Natural Gas, the regulator supplied is set for 4” water column.
The regulator is convertible to 10” water column for plumb-in system LP application. Do not use with a
20-lb LP cylinder. Make sure that the regulator is set for the correct gas type. To check, remove the brass
hex cap. You will find the conversion plastic pin attached to the cap to the underside of the cap.
If the disc (1/2 in. diameter) of the pin is close to the cap, then the regulator is set for Natural Gas.
If the disc is at the tip of the pin, away from the brass cap, the regulator is set for system LP application.
To convert to Natural Gas, remove the plastic conversion pin and invert and replace it back in a manner
such that the disc is close to the brass cap. For both Natural and LP, the maximum inlet pressure is 14”
water column.
PLASTIC INSERT
PLASTIC INSERT
SETTING UP FOR LP
BEFORE (SET FOR NG)
6
NATURAL GAS INSTALLATION – DELSOL GAS GRILL
A typical Natural Gas installation is shown below. Make sure that the factory-supplied regulator is
used and installed with the arrow mark on the regulator pointing towards the gas grill. Do not use any
replacement regulator other than that specified by DELSOL. Use only pipe sealants that are approved for
use with Natural and LP gases. An installer-supplied gas shutoff valve must be installed in an accessible
location.
7
LEAK TEST – DELSOL GAS GRILL
CAUTION BEFORE TESTING






Finding and/or fixing a gas leak is NOT a “DO-IT-YOURSELF” procedure.
NEVER USE THE GRILL WITHOUT FIRST LEAK TESTING THE GAS CONNECTIONS.
WARNING: DO NOT USE OPEN FLAME TO CHECK FOR LEAKS. USE OF AN OPEN FLAME
COULD RESULT IN A FIRE, EXPLOSION, BODILY HARM OR DEATH.
DO NOT SMOKE WHILE PERFORMING THE LEAK TEST!
To prevent fire or explosion hazard, DO NOT use or permit sources of ignition in the area while
performing a leak test. Perform leak test outdoors only.
Check to ensure that flexible hoses do not have any cuts and wear that may affect the safety before
each use. Only the factory supplied hose and regulator must be used. Use only replacement regulator
and hose assemblies specified by DELSOL.
LEAK TEST
1) Prepare a leak testing solution of sudsy water by mixing in a spray bottle with half liquid soap and half
water.
2) Confirm that all control knobs are in the OFF position.
3) Turn the main gas valve supply ON.
4) Apply leak testing solution by spraying on the pipe joints, fittings, and hose.
5) A gas leak is detected if;
a) there is a faint gas smell and/or…
b) …growing bubbles appear on any of the connection points and/or hose, DO NOT attempt to ignite
the grill and IMMEDIATELY turn off the gas supply valve.
6) When there is a gas leak, call a qualified service technician. DO NOT use the grill until the leak is
corrected.
8
BURNER FLAME / AIR SHUTTTER ADJUSTMENT – DELSOL GAS GRILL
Each grill burner is tested and adjusted at the
factory prior to shipment; however, variations in the
local gas supply may make it necessary to adjust the
burners.
The flames of the straight burners should be
visually checked. Flames should be blue and stable with
little to no yellow tips, no excessive noise or lifting. If
any of these conditions exist, remove the burner and
check to see if the air shutter or burner ports are blocked
by dirt, debris, spider webs, etc. If it is clear, the air
shutter may need to be adjusted.
Before adjusting the air shutter, verify that the correct orifice size for the gas type was installed.
ADJUSTING THE GRILL BURNER FLAME - The amount of air is controlled by a sheet metal
cup at the inlet of the burner called an air shutter. It is locked in place by a set screw which must be
loosened prior to lighting the burner for adjustment. The air shutter adjustment screws are accessible
with a phillips screwdriver. Loosen the lock screw of the air shutter. Adjust according to the following
directions. Be careful as the burner and other grill parts may be very hot!


If the flame is yellow, indicating insufficient air, turn the air shutter counter-clockwise to allow
more air to the burner.
If the flame is noisy and tends to lift away from the burner, indicating too much air, turn the air
shutter clockwise.
Remember to tighten the set screw prior to re-installing the burner.
ENSURE THAT THE BURNERS ARE SITTING PROPERLY ON THE ORIFICES BEFORE
LIGHTING THE BURNERS.
9
LOCATING THE GRILL – DELSOL GAS GRILL
This gas appliance is designed and certified for outdoor use only. Do not locate this grill under
overhead combustible surfaces. Do not operate the grill inside a building, garage, recreation vehicle or
any enclosed area. When choosing an area, consider exposure to wind, proximity to traffic paths and
length of gas supply line. Keep gas supply lines as short as possible to reduce pressure drop. Keep the
grill away from windy area but keep the grill in a well-ventilated area. Do not obstruct the flow of
combustion and ventilation air around the grill. The supporting edges of the grill must be located level
and flat. The counter should also be leveled. Ensure that the appliance remains at a distance of at least
12” from any combustible material such as wood, gyprock, paper and plants. Do not store combustible
materials, gasoline or flammable liquids or vapors around the appliance
CLEARANCE TO COMBUSTIBLE CONSTRUCTION
A minimum clearance of 12” from the sides and 12” from the back of the grill to adjacent vertical
combustible construction must be maintained.
DÉGAGEMENT DE TOUTE CONSTRUCTION COMBUSTIBLE
Il faut maintenir une distance minimum de 12 po (30.48 cm) sur les côtés et de 12 po (30.48 cm) sur
l’arrière du gril par rapport aux constructions combustibles verticales adjacentes.
CLEARANCE TO NONCOMBUSTIBLE CONSTRUCTION
A minimum clearance of 5 1/2” from the back of the grill above cooking surface to noncombustible construction is required to allow the grill hood to open completely.
A minimum of 8” clearance to the sides of the grill above cooking surface to non-combustible
construction is recommended to provide space for the rotisserie motor and the spit rod. The grill can
be installed directly next to non-combustible construction below the cooking surface.
DÉGAGEMENT DE TOUTE CONSTRUCTION INCOMBUSTIBLE
Une distance minimum de 5 1/2 po (13.97 cm) de l’arrière du gril au-dessus de toute surface de
cuisson à la construction incombustible est prescrite pour permettre à la hotte d’ouvrir complètement.
Une distance minimum de 6 po (15.24 cm) des côtés du gril au-dessus de la surface de cuisson à la
construction incombustible est recommandée pour prévoir de l’espace pour le moteur de la rôtissoire
et la poignée des broches de cuisson. Le gril peut être installé directement à proximité d’une
construction incombustible en-dessous de la surface de cuisson.
10
GRILL CUT-OUT DIMENSIONS – DELSOL GAS GRILL
The island must be made out of non-combustible
material. In an event it is combustible, the use of
an insulating jacket is required.
1
11
ASSEMBLY INSTRUCTIONS – DELSOL GAS GRILL
The DELSOL Grill is produced fully assembled and tested in the factory and requires no major
assembly in the field. For the purpose of safe shipping and transit, some parts such as the briquette trays
and rotisserie components are wrapped inside the grill and require minor assembly.
Check to ensure that all packaging material have been removed prior to grill operation.
TO INSTALL BRIQUETTES TRAYS
1. Put briquette trays into the grill above the burner as shown by lining up the pin with the cut-out of
the briquette tray.
2. Then put the stainless steel grates over the briquette trays.
PIN
CUT-OUT
WARMING RACK INSTALLATION:
The warming rack may be used to keep food warm and avoid overcooking the food. To install the
warming rack, rest the warming rack onto the warming rack ledge, then gently slide it back until it falls
into place.
STEP 1 & 2
STEP 3
12
ASSEMBLY INSTRUCTIONS – DELSOL GAS GRILL
OPTIONAL DELSOL ROTISSERIE KIT ASSEMBLY (DSRS-KIT)
1. Install the bracket as shown in figure 1.
2. Install the rotisserie motor as shown as shown in figure 2.
The motor socket hole will line up with the notch of the
rear hood.
3. Remove the stainless steel grates.
4. Place a basting pan on top of the briquette trays to catch the
drippings. (basting pan not supplied)
5. Insert the meat fork and the balancer (figure 3) and spit rod
saddle (figure 4) into the spit rod.
6. Insert the rotisserie rod into the motor socket hole and place
the rod on the notch of rear hood side.
7. Ensure that the groove of the spit rod saddle is resting on
the notch of the rear hood side as shown in figure 4. Tighten
the thumb screw to secure the spit rod.
Figure 2
Figure 3
Optional Rotisserie Kit fully installed on the grill.
13
Figure 1
Figure 4
OPERATING INSTRUCTIONS – DELSOL GAS GRILL
BEFORE LIGHTING THE GRILL

DO NOT ATTEMPT TO LIGHT THE GRILL IF YOU SMELL GAS.

WARNING! IT IS CRITICAL THAT THE GAS BURNERS ARE PROPERLY INSTALLED
WITH THEIR ORIFICES INSIDE THE BURNERS AIR SHUTTERS. If not properly
installed, gas may leak outside of the burner that could lead to fire, potential damage to your
grill, bodily injury or death.

Inspect the gas supply piping or hose prior to turning the gas ON. If there is evidence of cuts, wear,
or abrasion, it must be replaced prior to use. The replacement pressure regulator and hose assembly
must be the type specified by the manufacturer. Do not use the grill if the odor of gas is present. The
pressure regulator and hose assembly supplied with the units must be used.
If the unit is LP, screw the regulator and hand tighten to the valve of the cylinder and leak check the
hose and regulator connections with a soap and water solution before operating the grill. Reference
page 8 for leak test procedure.
Always keep your face and body as far away as possible when lighting.
Refer to spiders and insects warning and procedure under the cleaning and maintenance page of this
manual.



TO LIGHT THE GRILL BURNER
Lighting the Grill
1. Open the grill hood completely. Do not attempt to light the
grill with the hood closed.
2. Open the gas supply shut-off valve.
3. To ignite burners, push the burner knob in and slowly rotate
counter clockwise to the high position.
4. A loud click can be heard as the electronic lighter produces a
spark. Listen for the sound of the gas igniting and look for the
flame through the cooking grids. If the burner does not light on
the first try, repeat immediately.
For Rotisserie Lighting: For rear burner, a slower turn of the knob
is necessary. This allows gas to accumulate in the rear burner to
achieve ignition.
CAUTION: If ignition does not take place within 4 seconds, turn
knob to the OFF position, wait for five minutes and repeat step 3
and 4.
5. Close the hood to allow the grill to pre-heat until the hood
thermometer displays the desired grilling temperature.
Warning: If you smell gas, shutoff the gas supply and
immediately check for leaks using the soapy water technique.
66 (See Page 8)
14
OPERATING INSTRUCTIONS – DELSOL GAS GRILL
Match/BBQ Lighter Lighting Instructions:
If spark igniter will not light the burners, the burners can be lit
manually using a lit long match, taper or BBQ lighter.
1.
Push and turn the knob counter-clock-wise to the biggest flame
marking on the bezel.
2. Using the provided match holder located on the drip pan, insert
a lit match or BBQ lighter thru the grates and near the top of
the burner. Once you see or hear a flame you can release the
knob.
Important: If burner fails to light within 4 seconds, turn off gas
and wait 5 minutes before repeating the process.
Warning: If you smell gas, shutoff the gas supply and
immediately check for leaks using the soapy water technique.
(See Page 8)
USING THE GRILL
1. Check to be certain that the drip pan is in place and pushed all the way into the grill.
2. Light the grill burners using the instructions in use and care manual.
3. Turn the control knobs to HI and allow the grill to preheat for 15 minutes or until desired
temperature is displayed on the thermometer. The top cover is to be closed during the appliance
preheat period.
4. Place the food on the grill and cook to the desired temperature doneness. Adjust heat setting, if
necessary. The control knob may be set to any position between HI and LO.
5. Allow grill to cool then you may clean the drip pan after each use.
CAUTION: Do not operate the main burners with the rotisserie burner simultaneously.
15
OPERATING INSTRUCTIONS – DELSOL GAS GRILL
USING THE ROTISSERIE BURNER (For DSBQ32R & DSBQ40R Units)
The Rotisserie system rotates the food in front of infrared burner heat for even cooking and juicier taste.
1. Install the rotisserie motor on the motor bracket and plug it in to proper voltage.
2. Insert the food on the middle of the spit rod and then secure it with the meat holders on both ends by
tightening the thumb screws on the meat forks. If multiple pieces of food will be cooked at the same
time, make sure the load is evenly balanced on the spit rod. Proper weight balancing will lead to
evenness of cooking and prolong the life of the rotisserie motor.
3. Insert the spit rod in the rotisserie motor at desired cooking position. You may need to remove the
cooking grates to create clearance for bigger loads of foods. Reference assembly instructions for
rotisserie assembly instructions. (Page 14)
4. Locate the rotisserie knob which has the rotis symbol.
5. To ignite burners, push the burner knob in and slowly rotate counter clockwise to the high position. A
loud click can be heard as the electronic lighter produces a spark. Listen for the sound of the gas
igniting and check if the burner is lit. If the burner does not light on the first try, repeat immediately.
Once lit, the rotisserie burner will reach cooking temperature in about 1 minute.
CAUTION: If ignition does not take place within 4 seconds, turn knob to the OFF position, wait for
five minutes and repeat step 5.
NOTE: Once the burner has reached cooking temperature, adjust to low flame setting by
turning the knob to the low flame marking without pushing in on the knob.
6. Once cooking is completed, shut-off the rotisserie burner and main valve.
WARNING: When using the rotisserie always keep the front hood closed except when basting or
checking the meat for cooking completion. It is recommended to use a meat thermometer to check if
the food is completely cooked.
CAUTION: In sunny or heavy light environments, the flame from the infrared rotisserie burner may
be difficult to see and verify complete ignition.
CAUTION: Do not operate the rotisserie burner with the main burners simultaneously.
NOTE: The rotisserie motor must be stored in an area secured from the surrounding elements when
not in use. Do not leave it mounted on the grill.
16
GRILLING IN WINDY CONDITIONS – DELSOL GAS GRILL
Outdoor grills produce more heat than interior
kitchen ranges. That is how they sear and grill
steaks and other food.
These high performance burners require a
constant steady supply of fresh air to mix with
fuel. The grill is designed to pull air in through
the front and vent hot gases out through the rear.
Using grill in windy conditions may disrupt the
front-to-back air flow. If you notice the
temperature gauge fails to rise while the burner
setting is on high and hood is closed, be
extremely careful.
If wind has kept hot gases from exiting the
rear of the grill, the control panel and knobs
may have become extremely hot!
But there are a few things you can do to further
prevent the possibility of improper heat buildup:
 On breezy days, do not leave the front
hood down for more than 15 minutes
Wind hitting the back of the unit can
when burners are on high. (Never leave
disrupt proper air flow.
the grill unattended when in
operation.)
 If you suspect the grill is overheating, open the front hood using oven mitts. Then adjust the burner
control knob to a lower setting.
 Install your grill with a wind break behind it.
 Orient the grill so prevailing winds are not blowing into the rear of the grill.
WARNING: ANY DAMAGE CAUSED FROM USE OF GRILL IN WINDY CONDITIONS,
SUCH AS MELTED KNOBS OR MELTED IGNITER WIRES, OR FRONT PANEL
DISCOLORATION FROM HEAT BUILDUP IS EXCLUDED FROM WARRANTY
COVERAGE.
17
CLEANING & MAINTENANCE – DELSOL GAS GRILL
STAINLESS STEEL
The DELSOL grill is made of all stainless steel. It is non-rusting and non-magnetic. Never
clean the stainless steel when it is hot. After the initial grilling use, certain areas of the grill may discolor.
This is a normal discoloration caused by the intense heat given off by the burners. Specks of grease can
gather on the surface of the stainless steel and get baked-on. These can be removed by using a mild
abrasive pad (like Scotch Brite) with a stainless steel cleaner. Use the mildest cleaner and always scrub in
the direction of the grain.
Do not use steel wool to clean the grill. Do not use abrasives on the polished highlights. Be extra
careful when cleaning around the highlights. Metal polisher or mild chrome cleaner can be used to bring
back the luster on highlights. To touch-up minor scratches in the stainless steel, sand the affected surface
very lightly, with 100-dry grit emery sandpaper in the direction of the grain.
COOKING GRATES
The easiest way to clean the stainless steel grates is to
scrub them with a barbeque brush immediately after cooking is
completed and the flame is turned off.
Wear a barbeque mitt to protect your hands from the heat
and steam. Dip a brass bristle barbeque brush in tap water and
scrub the hot grill. Dip the brush frequently in tap water. Steam,
created as water comes in contact with the hot grill, helps loosen
food particles stuck in the grill. These food particles will either
get burned into the briquettes or fall into the cleaning pan.
Cleaning of the grill will be longer and more difficult if the grill
racks are allowed to cool before cleaning. When cleaning the
grates, make sure not to hit the rotisserie burner. Never spray
water on a hot grill.
CERAMIC BRIQUETTE TRAY
It is not necessary to remove and clean the briquettes
from the tray after every grilling. They will burn clean during
the next cooking operation.
Periodically, the briquette trays need to be cleaned.
Remove them from the grill, shake any loose debris free and
wipe the trays clean. Do not handle a hot briquette tray with
bare hands.
REPLACING BRIQUETTE TRAYS
1) Remove the trim that holds the briquettes.
2) Remove the old briquettes and place the new briquettes
in the same location as the old ones.
3) Replace the trim that holds briquettes.
18
CLEANING & MAINTENANCE – DELSOL GAS GRILL
BURNERS
Burners are made of heavy gauge stainless steel and can
be soaked in water and cleaned with a wire brush. Check every
port hole for clogs. Use a wire pin to clean out clogged ports.
Make sure the burner is dry before installing it back into the
grill.
DRIP PAN
The drip pan collects grease, liquid and fallen food
particles. Allow the pan and its contents to cool before cleaning.
Slide the pan out and wipe it clean. Make sure the drip pan is
fully inserted back into the grill. It is highly recommended to
clean the pan after every use to avoid any possibility of a grease
fire. DO NOT use the grill without the drip pan pushed all the
way to the back of the grill unit.
SPIDER AND INSECT WARNING
Spiders and other insects can nest in the burners of this and any other grills, which causes the gas
to flow from the front of the burner. This dangerous “condition” can cause a fire behind the valve panel,
damaging the grill and making the grill unsafe to operate. Inspect the burners once a year or if the grill
has not been used for more than one month or if any of the following conditions occur:
1) The smell of gas in conjunction with the burner flames appearing yellow.
2) The grill does not reach temperature.
3) The grill heats unevenly.
4) The burners make popping noises.
19
TROUBLESHOOTING GUIDE – DELSOL GAS GRILL
BEFORE CALLING FOR SERVICE:
If your DELSOL grill does not function properly, use the following troubleshooting guide before
contacting your dealer for service. The troubleshooting guide may save the cost of a service call and the
inconvenience of being without your grill.
PROBLEM
Grill will not light.
WHAT TO DO
1.
2.
3.
4.
Push in, turn the knob clockwise, and verify that the spark igniter functions.
Purge the line of any trapped air.
Check if you can match-light the burner.
Check to see that the other burners operate.
NOTE: It is normal to hear a popping sound when the grill burners are first
turned ON.
Burner flame is yellow
and gas odor can be
smelled.
1.
2.
3.
1.
Low heat generated
with knob in HI
position.
2.
3.
4.
5.
6.
1.
2.
3.
1.
2.
1.
2.
3.
4.
5.
6.
7.
Too much heat.
Excessive flare-up.
Burner blows out
Spark igniter does not
spark.
Thermometer is not
reaching high
temperatures
Check the burner inlet for obstruction…ex. Spiders, insects, etc.
Check the air shutter for proper adjustment.
Check any source of gas leak.
Check if the problem is isolated to only one burner. If it appears so, clean the
orifice and burner, clearing ports of any obstruction.
Check for any bent or kinked fuel hose.
Check if the air shutter is properly adjusted.
Check for proper gas supply and pressure.
Pre-heat grill for 15 minutes.
If using LP gas, check for empty tank.
Check for damaged orifice or no orifice.
Check for unauthorized regulator adjustment.
Check for proper gas supply and pressure.
Check if the cooking grids are dirty. Clean if necessary.
Overload from fatty meats or excessive cooking temperature.
Check for any burner defect.
Check for proper burner installation.
Check if fuel mixture is too lean.
Check if gas supply is sufficient.
Check if LP tank is empty.
Check if the grill location is subject to high winds.
Check for proper gas supply and pressure.
1. If the igniter does not spark, replace gas valve.
1. Allow the grill 15 minutes with hood closed at high setting in order to reach
higher temperatures.
20
EXPLODED VIEW – DELSOL GAS GRILL
21
REPLACEMENT PARTS LIST – DELSOL GAS GRILL
Item
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
TE Part No.
S15353
S13216
S12362
S12355
S12361
S14128
S21565-25WY
S21565-32WY
S21565-40WY
S14292
S14176
S21567
S12417-32
S12417-40
S16364-32
S16364-40
S13904-25
S13904-32
S13904-40
S21582
S21572-25WY
S21572-32WY
S21572-40WY
S21574-25
S21574-32
S21574-40
S13370
S12680-50
S12680-57
S13903
S21583Y
S21580
S21579
S13197
S13198
S13196
S13215
S14260
S21559-25WY
S21559-32WY
S21559-40WY
S12756-25
S12756-32
S12756-40
S21576-25
S21576-32
S21576-40
S21577-25
S21577-32
S21577-40
S15144-53
S15144-60
S12677
S13369
S14302
S21570
S16363
Description
Thermometer
Thermometer, Bezel
Tube, Handle, 25
Tube, Handle, 32
Tube, Handle, 40
Hood Bumper
Front Hood, weld assembly, 25
Front Hood, weld assembly, 32
Front Hood, weld assembly, 40
Screw, 1/4-20 x 1, Ph Truss, s/s
Nut 1/4 -20 Serr, Hex, Flange s/s
Plate, Thermometer
Flex Tubing, 32
Flex Tubing, 40
Wire, Igniter, 32
Wire, Igniter, 40
Warming Rack, 25
Warming Rack, 32
Warming Rack, 40
Rear Hood Access Panel
Rear Hood Weld Assembly, 25
Rear Hood Weld Assembly, 32
Rear Hood Weld Assembly, 40
Rear Hood Liner, 25
Infrared Panel, 32
Infrared Panel, 40
Infrared Burner
Infrared Burner Elbow, Brass, NG
Infrared Burner Elbow, Brass, LP
Grate
Briquette Tray Assembly
Burner Divider
Bottom Baffle
Grill Knob
Rotis Knob
Delsol Logo
Knob Bezel
Logo Clip
Front Panel Weld Assembly, 25
Front Panel Weld Assembly, 32
Front Panel Weld Assembly, 40
Manifold Pipe, 25
Manifold Pipe, 32
Manifold Pipe, 40
Drip Pan Handle, 25
Drip Pan Handle, 32
Drip Pan Handle, 40
Drip Pan, 25
Drip Pan, 32
Drip Pan, 40
Burner Valve with Flame Thrower, NG
Burner Valve with Flame Thrower, LP
Coupling, Elbow, Brass 3/8 Flare x 1/2FIP 90deg
Grill Burner
Cotter Pin
Rotis Igniter Cover
Rotis Igniter
Note:
Optional
DSBQ
25G-L
DSBQ
25G-N
DSBQ
32R-L
DSBQ
32R-N
DSBQ
40R-L
DSBQ
40R-N
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
2
1
1
2
2
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
2
1
2
2
1
1
1
1
2
1
2
2
1
1
1
2
2
1
1
1
1
3
3
2
3
3
3
3
2
3
3
1
3
2
1
1
3
2
1
1
1
1
1
1
1
1
1
4
4
3
4
4
1
1
5
2
4
4
3
4
4
1
1
5
2
1
1
1
1
1
1
1
1
1
5
1
1
1
1
3
3
1
3
3
1
1
1
1
5
5
4
5
5
1
1
6
2
1
1
1
1
5
5
4
5
5
1
1
6
2
1
3
3
1
4
4
1
4
4
1
1
1
4
4
1
1
5
1
5
5
1
1
1
5
5
1
1
*=
22
REPLACEMENT PARTS LIST – DELSOL GAS GRILL
Item
No.
54
55
56
57
58
TE Part No.
S12618
S15351
S15352
S13876
S15145-NG
S15145-LP
Description
Nipple, ½ Close, BI
NG Regulator
LP Regulator
Match Holder
Rotis Valve, NG
Rotis Valve, LP
DSBQ
25-L
DSBQ
25-N
DSBQ
32R-L
DSBQ
32R-N
DSBQ
40R-L
DSBQ
40R-N
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Non Shown Parts
S15143-53
S15143-60
S15146-50
S15146-57
*DSRS32-KIT
*DSRS40-KIT
Orifice #53 NG
Orifice #60 LP
Orifice #50, IR, NG
Orifice #57, IR, LP
32” ROTIS KIT
40” ROTIS KIT
3
3
4
4
5
5
1
1
1
1
1
1
1
Note: * = Optional
23
1
DELSOL GRILL WARRANTY
TEN YEAR LIMITED WARRANTY: DELSOL warrants the stainless steel grates, stainless steel burner, and fabricated
stainless steel housing to be free from defects in materials and workmanship under normal residential use
for ten years from the original date of purchase. This warranty excludes grills used in rental or
commercial applications. This warranty does not apply to rust, corrosion, discoloration, surface scratches,
weather and atmospheric related staining, and oxidation which are normal conditions and to be expected
with any outdoor product unless the affected component becomes inoperable. This warranty does not
cover labor or labor related charges. The actual part will be repaired or replaced with the owner paying
for all other costs, including labor, installation, shipping and handling charges.
ONE-YEAR FULL WARRANTY: DELSOL warrants the outdoor gas grill and all of its component parts including briquette
trays (excluding the briquettes), ignition system, gas system, rotisserie motor, infrared burners, housing
carts, thermometer, etc., to be free from defects in materials and workmanship under normal residential
use for a period of one year from the original date of purchase. The actual part will be repaired or
replaced, free of charge, with the owner paying for all other costs including labor, installation, shipping
and handling charges.
WARRANTY LIMITATIONS & EXCLUSIONS
This warranty shall apply only to the products purchased and located in the continental United States and Canada. The warranty
coverage begins on the original date of purchase and proof of date of purchase is required. In order to activate the warranty, we
require that you send in the attached warranty registration card. This warranty applies only to the original owner and may not be
transferred.
This warranty does not apply to damages resulting from negligence, alteration, misuse, abuse, accident, natural disaster,
improper installation or improper operation, unauthorized adjustments or calibrations, dings, dents, scratches, or damages due
to harsh cleaning chemicals. This warranty does not apply to rust, corrosion, discoloration, surface scratches, weather and
atmospheric related staining and oxidation which are normal conditions and to be expected with any outdoor products unless
the affected component becomes inoperable. This warranty does not apply to commercial use, or to products with altered or
removed serial numbers. DELSOL shall not be liable for incidental, consequential, special or contingent damages resulting
from its breach of this written warranty or any implied warranty.
WARRANTY SERVICE & REPLACEMENT PARTS: Call your authorized selling dealer or call DELSOL directly at 800422-0091 or 562-802-3391. Be prepared to furnish the following information: Purchaser’s name, model and serial number of
the grill, date of purchase and the accurate description of the problem. DELSOL will not pay for service calls for correcting an
installation problem. Owner shall be responsible for proper installation, providing normal care and maintenance, providing
proof of purchase upon request and making the grill accessible for service. In the event of any warranty replacement, all
removal, replacement, installation and shipping costs are the responsibility of the grill owner.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusions of or limitations on consequential
damages. This warranty gives you specific legal rights and you may have other rights, which vary from state to state.
24
HOW TO OBTAIN SERVICE
For service, please contact your DELSOL dealer or call DELSOL Grills direct at (562)802-3488 or
fax (562) 802-3391
Mailing address:
DELSOL Grills
13259 166th Street
Cerritos, CA 90703
Please provide:
 Model number
 Serial Number
 Date of installation
 A description of the problem
Cut
Here
Warranty Registration
Customer Name
Model #
Address
Serial #
City
Date Purchased
Zip
Dealer’s Name
Phone #
Dealer’s Address
e-mail:
This Warranty Registration card must be returned within thirty days of purchased to properly activate
your warranty. This information is for our internal use only.
Cut
Here
Place
Postage
Here
Customer Service
ATTN: Warranty Department
13259 166th Street
Cerritos, CA 90703
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising