Quantom 384 - Lanta Lighting
Owner Handbook
Quantom
384
384 Channel DMX Lighting Desk
™
For your Safety
• Follow all instructions to maintain Manufacturer Warranty and for your own safety.
• T here are no user replacement parts inside the product. Do not open the product for
any reason. This will invalidate your Manufacturer Warranty and may impair the safety
features of the product.
• Do not expose this product to moisture, rain or other fluids.
•D
o not use if the product if you suspect it has been damaged in any way, including
being dropped, is malfunctioning, or has been exposed to liquids or moisture. The unit
must be repaired by an authorised service centre only. Manufacturer Warranty is void
if unit is opened or adapted in any way. Operator safety may be compromised if this
product is not operated and maintained in accordance with the details contained in
this Owner Handbook.
• T his appliance must be earthed. Do not remove the earth connection in the plug or
any other location- it is essential for user safety.
•B
e aware that products are mains powered and may be capable of producing high
voltages from outputs and has mains voltages inside the cabinet.
Product Installation, Use & Maintenance
• Keep this Owner Handbook safe for future reference.
•C
lean the product with a clean and dry, non-abrasive cloth. Do not use solvents or
liquids to clean the product.
• T o prevent overheating, do not obstruct any ventilation opening, fan cover or vent. Do
not install near any sources of heat such as radiators, heaters, other heat producing
items such as amplifiers, power units etc.
•P
ower connection to the product is via a UK 240 Volt AC three-pin mains plug. Do not
remove or adapt this plug. If necessary, only replace the plug top fuse with one of the
same type, size and value.
• T he mains lead must not be crushed or damaged. If any damage occurs, disconnect
from the mains immediately. Replace the damaged cable, or if the mains lead is
captive, return the product to an authorised repair centre for cable replacement. Do
not attempt to repair the cable - it must be discarded and destroyed.
• T o maintain the Manufacturer Warranty, only attach authorised accessories and external
devices. This includes cables, connectors and other electrical and/or mechanical
devices.
•U
nplug the product from the mains during lightning storms or periods of mains
fluctuations. If the product is going to be unused for long periods, unplug from the
mains.
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
Product Quality & Compliance
Products from Lanta Lighting meet all required safety standards in force at the time of
manufacture and are fully compliant with them.
Unpacking & Inspection
• Inspect the packaging before opening. If the packaging appears to have sustained
significant damage, please take extra care before using the product. If you are in any
doubt, consult a suitably qualified professional.
• If you suspect the product has been damaged, do not use it. Return it to your original
supplier without delay.
• Keep all packaging in a safe place for storage or transport in future.
Manufacturer Warranty
• This Manufacturer Warranty is valid in the UK only.
• L anta Lighting warrants that this product is free from workmanship defects and material
failure during normal use and operation for a period of 12 months from first use or from
original date of sale (whichever is the earliest) providing all of the terms indicated in the
warranty section have been fully complied with.
•E
xpressly excluded is our liability for any directly connected or indirectly connected item
or items or any consequential loss associated with the failure of the product howsoever
caused.
• If the product has been opened, modified, tampered with, incorrectly connected,
used inappropriately or in conflict with the instructions herein, or the product model
or serial number has been damaged, removed, tampered with, obliterated or made
partly unreadable by any person or persons, the Manufacturer Warranty is irrevocably
null and void.
•N
o extension, adaption, alteration or modification to the terms of this Manufacturer
Warranty will be permitted, unless expressly authorised in writing (excluding email and
fax) by a Director of Lanta Lighting. Warranty is transferrable during the Warranty period.
For Further Information about Lanta Lighting
Our website can be found at www.lantalighting.com and is available for the benefit
of customers worldwide. Please consult for information, advice and support on this and
other high quality products from Lanta.
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
About Lanta Lighting™
Based in the UK, Lanta are committed to providing high quality products at cost-effective
prices to the professional lighting market. Since the first product was launched in 2006,
Lanta has established a reputation for reliability, common sense design and customer
support that has become the envy of others.
The Lanta Lighting range includes:-
Professional Lighting
Focussing on the use of LED technology, Lanta offer distinctive lighting effects for install
and mobile applications. From washes to floods, spots to projectors, LED technology now
outperforms traditional lights while at the same time requiring significantly lower power
and generating far less unwanted heat.
Performance Lasers
Recent advances have reduced the costs of Lasers, made them more portable and
brought improved performance and reliability. With step and animation lasers in multi
and single colour formats for mobile DJs and static installs, Lanta promise Lasers that
won’t burn a hole in your pocket.
Atmospheric Effects
When you need special atmospherics effects, Lanta have everything from bubble
machines to snow machines, hazers and foggers. There’s also a range of fluids and
consumables specially designed to get the best from the range.
Control Gear
Lightweight and portable, Lanta Control Gear is robust enough to survive life on the road
and smart enough to control DMX kit whatever the venue.
Visit us at www.lantalighting.com for more details.
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
Getting to know your Lanta Product
With 384 Channels of DMX512 control, the Quantom 384™ lighting desk confidently
handles advanced lighting fixtures with responsive faders, a clear interface and an easy
to read LED display. Suitable for rack or desk-top mounting, the lightweight unit is extremely
portable but robust enough to cope with the rigours of life on the road. Up to 12 fixtures
can be run from one unit with the added flexibility of user-defined chases and static
scenes pulled from pre-programmed memory.
Channel Capacity
384 Total (12 Scanner Fixture of 32 Channels)
Scene Steps
240 Total (30 Program Banks of 8 Scenes Steps)
Chase Sequences
6 sets of 240 Scenes Steps
Input Connections
Locking 3 Pin Male XLR Socket
Output Connections
Locking 3 Pin Female XLR Socket
Power Requirement
9V-12V DC 500mA from 240 Volt AC 50/60Hz
Dimensions W x D x H
520mm x 190mm x 80mm
Max Operating Temperature
45ºC
Weight
3.0Kg
Scanner Fixtures
A Scanner Fixture is a individual lighting device. The unit can control up to 12 individual
Scanner Fixtures. Each Scanner Fixture can be driven by 32 Channels of industry standard
DMX512 control signals.
Scene Steps
A Scene Step is a static lighting state. The lighting state for all Scanner Fixtures connected
to the unit can be set for every Scene Step.
Program Banks
Scene Steps are stored in Program Banks which allow different Scene Steps to be called
up in sequential order. The unit allows 30 Program Banks to be created with 8 Scenes
Steps in each, for a grand total of 240 Scene Steps
Chase Sequences
A Chase Sequence contains Scene Steps. In a Chase Sequence, Scenes Steps can be
called up in any required order. Up to 6 Chase Sequence can be stored, each holding
up to 240 Scene Steps.
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
System Setup
1- Pan/Tilt Fader Settings
Pan/Tilt channels can be assigned for every individual Scanner Fixture if required. This
allows the unit to cope with features unique to a specific Scanner Fixture and allows
consistent control of all Scanner Fixtures used in a venue.
Setting Fader Assignments
1) Press and hold the PROGRAM button until the LED blinks
2) Press and hold PROGRAM & TAPSYNC different DMX channel. Faders can be assigned
to output on a different DMX channel. To cancel any assignment press the AUTO/DEL
& MODE buttons together
3) Press SCANNER or PAGE SELECT to select a Scanner Fixture
4) Move a fader from 1-16 to assign Pan
5) Press TAPSYNC to select Pan/Tilt
6) Move a fader from 1-16 to assign Tilt
7) Press and hold PROGRAM & TAPSYNC to store and exit. All LEDs will blink
2- Cloning Scanner Fixture Settings
To Clone Scanner Settings
1) Press and hold Source SCANNER button
2) While holding the Source SCANNER button, press the Destination SCANNER button
3) Release the Source SCANNER button, then release the Destination SCANNER button
4) All SCANNER LED indicators will flash to confirm successful copy
3- Cross-Fade Intervals
You can choose whether the board’s fade time during scene execution is implemented
broadly to all output channels or only to the Pan & Tilt movement channels. This is relevant
because often you will want gobos and colors to change quickly while not affecting the
movement of the light.
Setting Cross-Fade Intervals
1) Turn the unit OFF
2) Hold the BLACKOUT & TAPSYNC buttons simultaneously.
3) Turn the unit ON
4) Press the TAPSYNC button to toggle between the available modes, A (All Channels) or
P (Pan/Tilt only)
5) Press BLACKOUT and TAPSYNC to save settings. All LEDs will blink to confirm.
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
4- Scanner Fixture DMX Settings
The unit provides 32 channels of DMX-512 control per Scanner Fixture. Starting DMX
Address settings for individual Scanner Fixtures must be spaced 32 Channels apart as on
the table below. Settings for standard 9-pin Binary Dipswitches are shown for ease.
Fixture No
Address
DMX Range
Binary Dipswitch “ON”
1
1
1-32
1
2
33
33-64
1&6
3
65
65-96
1&7
4
97
97-128
1, 6 & 7
5
129
129-160
1&8
6
161
161-192
1, 6 & 8
7
193
193-224
1, 7 & 8
8
225
225-256
1, 6, 7 & 8
9
257
257-288
1&9
10
289
289-320
1, 6 & 9
11
321
321-352
1, 7 & 9
12
353
353-385
1, 6, 7 & 9
5- Full Factory Reset
Warning! This will reset all data, including Program Banks, Chase Sequences and Scene
Steps, to their original factory settings
To Perform a Factory Reset
1) Turn the unit OFF
2) Press and hold BANK UP and AUTO/DEL
3) Turn power to the unit ON whilst still holding BANK UP and AUTO/DEL
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
Programming The Unit
1- Scene Steps
Creating a Scene
1) Press the PROGRAM button until the LED blinks. Deselect Blackout if LED is lit.
2) Position SPEED and FADE TIME faders to their zero values toward the front of the unit.
3) Select the SCANNERS you wish to include in your Scene. You can select more than one
Scanner Fixture. You can access channels 17-32 by pressing the Page Select button.
This is necessary for fixtures that use more than 16 channels of control.
4) Adjust faders to required values. Press the FINE button, use fader by moving it then use
the BANK UP/DOWN buttons to change values in increments of 1
5) Tap MIDI/ADD button
6) Choose a BANK (01-30) to change if necessary
7) Select a SCENES button to store. The LED display will now indicate the Scene number
and Bank number used.
8) Repeat steps 3 through 7 as necessary. 8 scenes can be recorded in a Program Bank.
All LEDs will flash to confirm.
9) To exit program mode, hold the PROGRAM button
Inserting a Scene Step
1) Press and hold the PROGRAM button to enter programming mode
2) Press the desired CHASE button
3) Press the TAPSYNC to switch the LCD display to steps view.
4) Use the BANK UP/DOWN buttons to navigate steps and locate the insert point of the
new scene. The display will read the step number. For example, To insert a Scene
Step between Steps 05 and 06 navigate using BANK buttons until the display reads
“STEP05”
5) Press MIDI/ADD button to prepare the insert.
6) Use the BANK UP/DOWN button to locate the SCENE
7) Press the SCENE button that corresponds to the Scene Step to be inserted
8) Press MIDI/ADD button to insert the scene. All LEDs will blink
Reviewing a Scene Step
1) Make sure you are in MANUAL Mode
2) Select any one of the 30 banks by pressing the BANK UP/DOWN buttons.
3) Select a SCENE button (1-8) to review
4) Move faders to change Scanner Fixture values
Copying a Scene Step
1) Press and hold the PROGRAM button to enter programming mode.
2) Select BANK that contains original Scene Step using the BANK UP/DOWN buttons
3) Press the SCENE button that corresponds to the Scene Step to be copied
4) Press MIDI/ADD button to copy the scene
5) Select the destination BANK that contains the scene memory to record onto using the
BANK UP/DOWN buttons.
6) Press the desired SCENE button to complete copy. All LEDs will blink.
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
Deleting an Individual Scene Step
1) Press and hold the PROGRAM button to enter programming mode
2) Select BANK that contains Scene Step to be deleted with BANK UP/DOWN buttons
3) Press and hold the AUTO DEL button
4) Press the SCENE button that corresponds to the Scene Step you want to delete. All LEDs
will blink. When deleting a scene the physical location is not removed, however, all 384
DMX channels available to the scene will be set to value 0.
Deleting all Scene Steps
Warning - This process is irreversible! All Scenes Steps with data will zeroed.
1) Press and hold the PROGRAM button and the BANK DOWN button while turning off
power to the unit.
2) Turn the unit back on
2- Program Banks
Running a Program Bank
1) Use BANK UP/DOWN buttons to change Program Banks. Deselect Blackout if LED is lit.
2) Press the AUTO DEL button repeatedly until the AUTO LED turns on
3) Adjust PROGRAM speed via the SPEED fader and loop rate via the FADE TIME fader.
4) Alternatively tap the TAPSYNC button twice. The time between two taps sets the time
between SCENES (up to 10 minutes).
Checking a Program Bank
1) Press and hold the PROGRAM button until the LED blinks
2) Use the BANK UP/DOWN buttons to select the Program Bank to review.
3) Press the SCENES buttons to review each Scene Step individually
Editing a Program Bank
1) Press and hold the PROGRAM button until the LED blinks. Deselect Blackout if LED is lit.
2) Use BANK UP/DOWN buttons to change Program Banks if necessary
3) Select the desired fixture via the SCANNERS button
4) Adjust and change fixture attributes using the channel faders and wheel
5) Press the MIDI/ADD button to prepare the save
6) Select the desired SCENES button to save
Copying a Program Bank
1) Press and hold the PROGRAM button until the LED blinks
2) Use BANK UP/DOWN buttons to select the Program Bank to copy. All 8 Scene Steps in
the Program Bank will be copied
3) Press the MIDI/ADD button to prepare the copy
4) Use BANK UP/DOWN buttons to select the destination PROGRAM bank
5) Press MUSIC BANK COPY button to execute the copy. All LEDs on the controller
will blink
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
3- Chase Sequences
Creating a Chase Sequence
1) Press the PROGRAM button until the LED blinks
2) Press the CHASE (1-6) button you wish to program
3) Change BANK if necessary to locate a scene
4) Select the SCENE to insert
5) Tap the MIDI/ADD button to store
6) Repeat steps 3-5 to add additional Scene Steps in the Chase Sequence. Up to 240
Scene Steps can be recorded.
7) Press and hold the PROGRAM button to save the Chase Sequence
Running a Chase Sequence
1) Press a CHASE button then press the AUTO DEL button.
2) Adjust the Chase speed by tapping the TAPSYNC button twice at a rate of your
choosing. The time between 2 taps will set the chase speed (up to 10 minutes)
Checking a Chase Sequence
1) Make sure you are in MANUAL Mode
2) Select the desired CHASE button
3) Press the TAPSYNC button to switch the LCD display to steps
4) Review each Scene Step individually by using the BANK UP/DOWN buttons.
Copying a Program Bank
1) Press and hold the PROGRAM button to enter programming mode.
2) Press the desired CHASE button.
3) Select the BANK to be copied using the BANK UP/DOWN buttons.
4) Press MUSIC/BANK COPY button to prepare copy.
5) Press MIDI/ADD button to copy the bank. All LEDs will blink
Copying a Scene Step
1) Press and hold the PROGRAM button to enter programming mode.
2) Press the desired CHASE button
3) Select BANK that contains the scene to be copied using the BANK UP/DOWN buttons.
4) Press the SCENE button that corresponds to the scene to be copied
5) Press MIDI/ADD button to copy the scene. All LEDs will blink
Inserting a Scene Step
1) Press and hold the PROGRAM button to enter programming mode
2) Press the desired CHASE button
3) Press the TAPSYNC to switch the LCD display to steps view
4) Use the BANK UP/DOWN buttons to navigate steps and locate the insert point of the new
scene. The display will read the step number. For example, to insert a scene between
Steps 05 and 06 navigate using BANK buttons until the display reads “STEP05”
5) Press MIDI/ADD button to prepare the insert
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
6) Use the BANK UP/DOWN button to locate the SCENE
7) Press the SCENE button that corresponds to the scene to be inserted
8) Press MIDI/ADD button to insert the scene. All LEDs will blink.
Deleting a Scene Step
1) Press and hold the PROGRAM button to enter programming mode.
2) Press the desired CHASE button that contains the scene to be deleted
3) Press the TAPSYNC button to switch the LCD display to steps.
4) Select the scene/step to be deleted using the BANK UP/DOWN buttons
5) Press AUTO DEL button to delete the step/scene. All LEDs will blink
Deleting an Individual Chase Sequence
1) Press and hold the PROGRAM button to enter programming mode.
2) Press the CHASE button (1-6) to be deleted
3) Press and hold AUTO DEL button and the respective CHASE button to delete the Chase
Sequence. All LEDs will blink
Deleting All Chase Sequences
Warning! This procedure will result in irrevocable loss of Chase Sequence memory. The
individual Scene Steps and Program Banks will be preserved. It is highly recommended
that prior to programming a Chase Sequence for the first time all Chase Sequences are
deleted from memory.
1) Turn OFF controller
2) Press and hold BANK DOWN & AUTO DEL buttons while turning the unit ON.
3) All LEDs will blink
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
Operating Modes
1- Manual Control
Manual Control allows direct control of Scanner Fixtures. Faders and wheels can move
Scanner Fixtures and change their DMX values. Changes made will not be stored.
Controlling Scanners Manually
1) Press the AUTO DEL button repeatedly until the MANUAL LED is lit
2) Select a SCANNER button
3) Move faders to change Scanner Fixture attributes
4) Press the TAPSYNC button to toggle the output indicator on the LCD display between
DMX values (0-255) and percentage (0%-100%)
2- Sound Activated
In this mode, programs will be triggered by the sound using its built-in microphone.
Multiple chases selected will loop and run in the order originally selected.
Choosing Sound Activated Mode
1) Press the MUSIC BANK COPY button until the MUSIC LED turns on.
2) Select program BANK to run in Sound Active mode using the BANK UP/DOWN buttons.
3) Alternatively you can press a single CHASE button (1-6) or several CHASE buttons in
sequence and all selected chases will loop in the order selected
4) You can adjust the duration time using the FADE TIME fader.
3- Auto Run
In the Auto Run mode, programs will be triggered by the unit’s fade and speed values set
by faders. Multiple chases selected will loop and run in the order originally selected.
Choosing Auto Run Mode
1) Press the AUTO DEL button until the AUTO LED turns on
2) If a CHASE button is not pressed the controller will automatically run a BANK program.
3) Change BANK programs by using BANK UP/DOWN buttons
4) Alternatively you can press a single CHASE button (1-6) or several CHASE buttons in
sequence and all selected chases will loop in the order selected.
5) You can adjust the time between steps by moving the SPEED fader and the duration
of the step by moving the FADE TIME fader.
Choosing Multiple Chases
To avoid conflict between Scene Steps running simultaneously that control the same
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
fixture attributes consider creating individual color and gobo chases.
1) Press and hold AUTO DEL button.
2) While holding down AUTO DEL, in succession press and release each CHASE you
would like to run simultaneously.
4- MIDI Operation
The controller will only respond to MIDI commands on the MIDI channel which it is set to
full stop. All MIDI control is performed using Note on commands. All other MIDI instructions
are ignored. To stop a chase, send the blackout on note.
Choosing MIDI Operation
1) Press and hold the MIDI/REC button for about 3 seconds.
2) Select the MIDI control channel (1-16) via the BANK UP/DOWN buttons to set. This is the
Channel that the controller will receive MIDI note commands.
3) Press and hold the MIDI/ADD button for 3 seconds to save settings.
4) To release MIDI control, press any other button except the BANK buttons during step 2
MIDI Note
Effect (Turn On/Off)
MIDI Note
Effect (Turn On/Off)
00 to 07
08 to 15
Scene Steps 1-8, Program Bank 1
88 to 95
Scene Steps 1-8, Program Bank 12
Scene Steps 1-8, Program Bank 2
96 to 103
Scene Steps 1-8, Program Bank 13
16 to 23
Scene Steps 1-8, Program Bank 3
104 to 111
Scene Steps 1-8, Program Bank 14
24 to 31
Scene Steps 1-8, Program Bank 4
112 to 119
Scene Steps 1-8, Program Bank 15
32 to 39
Scene Steps 1-8, Program Bank 5
120
Chase 1
40 to 47
Scene Steps 1-8, Program Bank 6
121
Chase 2
48 to 55
Scene Steps 1-8, Program Bank 7
122
Chase 3
56 to 63
Scene Steps 1-8, Program Bank 8
123
Chase 4
64 to 71
Scene Steps 1-8, Program Bank 9
124
Chase 5
72 to 79
Scene Steps 1-8, Program Bank 10
125
Chase 6
80 to 87
Scene Steps 1-8, Program Bank 11
126
Blackout
5- Blackout
The Blackout button brings all lighting output to 0 or off.
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
Top Panel Configuration
384
PAGE A
1
2
3
PAGE B
17
18
19
10
4
5
20
21
10
6
7
22
23
10
8
24
10
9
4
25
10
11
26
27
10
12
13
28
29
10
14
15
30
31
10
16
BLACKOUT
32
PROGRAM
8
8
8
8
8
8
8
MUSIC
TRIGGER
STEP / TIME
8
7
STEP
10
8
CHASE SCENE
BANK
PAGE A
SCENE 1
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
0
0
0
0
0
0
0
0
SCENE 2
SCENE 3
SCENE 4
SCENE 5
SCENE 6
SCENE 7
SCENE 8
3
SCENES
10 BANK DOWN
9
BANK UP
0.1/SEC
PAGE B
18 PAGE
13
8
164
6
6
4
8
2
10
0
30 SEC
14
MIDI/ADD
AUTO/DEL
15 CHASE 4
CHASE 5
17
0 SEC
SPEED
SPEED
5
10
2
10 MIN
SELECT
PROGRAM
0
AUTO
TRIGGER
MUSIC
BANK COPY
6
FADE
TIME
TAP SYNC
DISPLAY
11
2
SCAN 1
SCAN 2
SCAN 3
SCAN 4
SCAN 5
SCAN 6
SCAN 7
SCAN 8
SCAN 9
SCAN 10
SCAN 11
SCAN 12
1
SCANNERS
CHASE 1
CHASE 2
CHASE 3
CHASE 6
12
BLACKOUT
384
Description
Effect
Description
Effect
1
Scanner Select
Selects fixtures 1-12
10
Bank Down
Changes scene/step in banks/
chases. Changes DMX value
in Fine mode.
2
Scanner Indicator LED
Shows fixture selected
11
Tap Sync Display
Tap-sync changes DMX value
to percentages
3
Scene Select
Selects scene
12
Blackout
Instant blackout of all fixtures
4
Channel Fader
Adjusts DMX values of Ch1-16
and Ch17-32
13
MIDI/Add
Activates MIDI control.
Confirms record/save.
5
Program
Enters Programming mode
14
Auto/Del
Activates Auto mode. Delete
when programming
6
Music/Bank Copy
Activates Music Mode. Copy
function in Programming
mode.
15
Chaser
Selects Chase1-6
7
LED Display
Shows detail
16
Speed Fader
Adjusts scene/step hold time
during chase
8
Mode Indicator LED
Shows Manual, Music or Auto
mode
17
Fade Time Fader
Cross fade interval between
two scenes
9
Bank Up
Changes scene/step in banks/
chases. Changes DMX value
in Fine mode.
18
Page Select
Toggles control between Page
A & Page B
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
Rear Panel Configuration
MIDI
DMX OUT
DMX IN
DC INPUT
LAMP
POWER
I
0
19
20
21
22
23
24
Description
Effect
19
MIDI Input
Allows use of MIDI control
20
DMX Output
Locking 3 Pin Female XLR Socket
21
DMX Input
Locking 3 Pin Male XLR Socket
22
DC Input
Main power feed jack
23
Gooseneck Lamp
USB power for lamp
24
Power
On/Off Rocker switch
Quantom 384 Owner Handbook ™
© Lanta Lighting™ 2010-2011. Terms Apply. All trademarks are the property of their
respective owners. E&OE. All specifications and details are correct at time of print.
Revision 2
www.lantalighting.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising