CLF Conan - Kellertheater Wangen

CLF Conan - Kellertheater Wangen
Co
na
n
CLF Conan
V 2.11 JULY 2015
Dimensions
All dimensions are in millimeters
2
Safety Information
WARNING!
Read the safety precautions in this section before
installing, powering, operating or servicing this
product
The following symbols are used to identify important safety information on the product and in this manual:
DANGER!
Safety hazard.
Risk of severe
injury or death.
DANGER!
Hazardous
voltage. Risk of
lethal or severe
electric shock.
WARNING!
Fire hazard.
WARNING!
LED light
emission. Risk of
eye injury.
WARNING!
Burn hazard. Hot
surface. Do not
touch.
WARNING!
Wear protective
eyewear.
WARNING!
Refer to user
manual.
Warning! Risk Group 3 (high risk) LED product according to EN 62471. Do not look into the beam at a distance
of less than 8.3 meters from the front surface of the product. Do not view the light output with optical
instruments or any device that may concentrate the beam.
This product is for professional use only. It is not for household use.
This product presents risks of severe injury or death due to fire and burn hazards, electric shock and falls.
Read this manual before installing, powering or servicing the fixture, follow the safety precautions listed below and
observe all warnings in this manual and printed on the fixture. If you have questions about how to operate the fixture safely,
please contact your supplier
PROTECTION FROM ELECTRIC SHOCK
Disconnect the fixture from AC power before removing or installing any cover or part and when not in use.
l
l
Always ground (earth) the fixture electrically.
l
Use only a source of AC power that complies with local building and electrical codes and has both overload and
ground-fault (earth-fault) protection.
l
Before using the fixture, check that all power distribution equipment and cables are in perfect condition and rated for
the current requirements of all connected devices.
l
Power input and throughput cables must be rated 20 A minimum, have three conductors 1.5 mm² (16 AWG) minimum
conductor size and an outer cable diameter of 5 - 15 mm . Cables must be hard usage type (SJT or equivalent) and
heat-resistant to 90° C minimum.
l
Use only PowerCon cable connectors to connect to power input sockets. Use only PowerCon cable connectors to
connect to power through put sockets.
l
Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other component is
damaged, defective, deformed, wet or showing signs of overheating. Do not reapply power until repairs have been
completed.
3
l
Do not expose the fixture to rain or moisture.
l
Refer any service operation not described in this manual to a qualified technician.
l
Socket outlets used to supply fixture fixtures with power or external power switches must be located near the fixtures
and easily accessible so that the fixtures can easily be disconnected from power.
PROTECTION FROM BURNS AND FIRE
l
Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C .
l
The exterior of the fixture becomes hot during use. Avoid contact by persons and materials. Allow the fixture to
cool for at least 10 minutes before handling.
l
Keep all combustible materials (e.g. fabric, wood, paper) at least 100 mm away from the head.
l
Keep flammable materials well away from the fixture.
l
Ensure that there is free and unobstructed airflow around the fixture.
l
Do not illuminate surfaces within 200 mm of the fixture.
l
Do not attempt to bypass thermostatic switches or fuses.
l
If you relay power from one fixture to another using power throughput sockets, do not connect more than ten fixture
fixtures in total to each other in an interconnected chain.
l
Connect only other fixture fixtures to fixture power throughput sockets. Do not connect any other type of device to these
sockets.
l
Do not stick filters, masks or other materials onto any optical component.
l
Do not modify the fixture in any way not described in this manual
PROTECTION FROM INJURY
l
Do not look continuously at LEDs from a distance of less than 8.3 meters from the front surface of the fixture without
protective eyewear such as shade 4-5 welding goggles. At less than this distance, the LED emission can cause eye
injury or irritation. At distances of 8.3 meters and above, light output is harmless to the naked eye provided that the
eye’s natural aversion response is not overcome.
l
Do not look at LEDs with magnifiers, telescopes, binoculars or similar optical instruments that may concentrate the light
output.
l
Ensure that persons are not looking at the LEDs from within 8.3 meters when the product lights up suddenly. This can
happen when power is applied, when the product receives a DMX signal, or when SERVICE menu items are selected.
l
Fasten the fixture securely to a fixed surface or structure when in use. The fixture is not portable when installed.
l
Ensure that any supporting structure and/or hardware used can hold at least 10 times the weight of all the devices they
support.
l
Allow enough clearance around the head to ensure that it cannot collide with an object or another fixture when
it moves.
l
Check that all external covers and rigging hardware are securely fastened.
l
Block access below the work area and work from a stable platform whenever installing, servicing or moving
the fixture.
l
Do not operate the fixture with missing or damaged covers, shields or any optical component.
4
Contents
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Fixture overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power cables and power plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Relaying power to other devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Data link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting the data link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Tips for reliable data transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Physical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Fastening the fixture to a flat surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Control panel and menu navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DMX address setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
WDMX control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Control mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Restoring factory default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation and effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Standard mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Manual mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Onboard control menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5
Fixture overview
G Clamp with
Quicklock # 875760
(Optional)
Safety cable attachment point
DMX output
Antenna wireless solutions(optional)
AC mains power
throughput
Display
Control buttons
DMX input
AC mains power
input
Note: head fan grill in production models is rotated 90° compared to this illustration.
6
Introduction
l
This compact LED-based Parcan features:
l
Beam RGBW color control with color temperature control
l
‘Color wheel’ color snap Beam
l
Onboard control panel and backlit LCD graphic display
l
Motorized zoom
l
Smooth electronic dimming
l
Electronic shutter with strobe and pulse effects
l
Calibrated and raw modes
l
Osram Ostar high-power emitters
l
DMX control
Using for the first time
Warning! Read “Safety Information” on page 3 before installing, powering, operating or servicing the
fixture. Before applying power to the fixture:.
l
Carefully review “Safety Information” starting on page 3.
l
Check that the local AC mains power source is within the fixture’s power voltage and frequency ranges.
l
See “Power cables and power plug” on page 8. Install a PowerCon power input connector on a suitable
power cable. If drawing power from a mains power outlet, install a suitable power plug on the power cable.
7
AC power
Warning! Read “Safety Information” starting on page 3 before connecting the fixrures to AC mains power.
Warning! For protection from electric shock, the fixture must be grounded (earthed). The powerdistribution circuit
must be equipped with a fuse or circuit breaker and ground-fault (earth-fault)protection.
Warning! Socket outlets or external power switches used to supply the fixture with power must be located near
the fixture and easily accessible so that the fixtures can easily be disconnected from power.
Important! Do not insert or remove live PowerCon connectors to apply or cut power, as this may cause arcing at
the terminals that will damage the connectors.
Important! Do not use an external dimming system to supply power to the fixture, as this may cause damage to the
fixture that is not covered by the product warranty.
The fixture can be hard-wired to a building electrical installation if you want to install it permanently, or a power plug that is
suitable for the local power outlets can be installed on the power cable.
Power voltage
Warning! Check that the voltage range specified on the fixture,s serial number label matches the local AC mains
power voltage before applying power to the fixture.
The fixtures accept AC mains power at 100-240 V nominal, 50/60 Hz. Do not apply AC mains power to the fixture at any
other voltage than that specified on the fixture’s serial number label.
Power cables and power plug
Power input and throughput cables must be rated 20 A minimum, have three conductors 1.5 mm² (16 AWG) minimum
conductor size and an outer cable diameter of 5 - 15 mm. Cables must be hard usage type (SJT or equivalent) and heatresistant to 90° C minimum. In the EU the cable must be HAR approved or equivalent.
If you install a power plug on the power cable, install a grounding-type (earthed) plug that is rated 20 A minimum. Follow
the plug manufacturer’s instructions. Table 1 shows standard wire color-coding schemes and some possible pin
identification schemes; if pins are not clearly identified, or if you have any doubts
Wire Color
(EU models)
Wire Color
(US models)
Conductor
Symbol
Screw (US)
brown
black
live
L
yellow or brass
blue
white
neutral
N
silver
yellow/green
green
ground (earth)
or
Table 1: Wire color-codig and power connections
8
green
Relaying power to other devices
Warning! Do not connect more than ten fixture fixtures in total to AC mains power in one interconnected chain
Power can be relayed to another device via the light-grey PowerCon throughput socket that accepts a light-grey PowerCon
cable connector. Note that blue input and light-grey throughput connectors have different designs: one type cannot be
connected to the other.
If you link fixtures in a chain so that they all draw AC mains power via the first fixture, certain points must be respected:
2
l
A hard usage, three-conductor, 16 AWG or 1.5 mm cable with SJT or equivalent cable jacket must be used to connect
the first fixture to AC mains power and to interconnect all the fixtures in the chain up to a maximum of seven fixtures in
total.
l
Light-grey PowerCon connectors must be used to draw AC mains power from the fixtures' power throughput sockets
and blue PowerCon connectors must be used to supply power at the fixture's power input sockets.
l
No matter what the AC mains power voltage is, do not connect more than ten fixture fixtures in total(i.e. including the
first fixture) to AC mains power in one interconnected daisy chain using power input and throughput connectors.
Data link
A DMX 512 data link is required in order to control a fixture via DMX.
The fixture has 3-pin XLR connectors for DMX data input and output. The pin-out on all connectors is pin 1 = shield,
pin 2 = cold (-), and pin 3 = hot (+).
Or the fixture has 5-pin XLR connectors for DMX data input and output. The pin-out on all connectors is
pin 1 = shield, pin 2 = cold (-), and pin 3 = hot (+). Pins 4 and 5 in the 5-pin XLR connectors are not used
Connecting the data link
To add more fixtures or groups of fixtures when the above limit is reached, add a DMX universe and another daisychained link.
Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit control data
reliably over long runs. 24 AWG cable is suitable for runs up to 300 meters. Heavier gauge cable and/or an amplifier is
recommended for longer runs.
Tips for reliable data transmission
To connect the fixture to data:
1. Connect the DMX data output from the controller to the closest fixture’s male 3-pin XLR DMX input connector.
2. Connect the DMX output of the fixture closest to the controller to the DMX input of the next fixture and continue
connecting fixtures output to input.
9
Physical installation
Warning! The fixture must be either fastened to a flat surface such as a stage or wall, or clamped to a truss or
similar structure in any orientation using a rigging clamp. Do not apply power to the fixture if it is standing freely
or the fixture can be moved.
Warning! If the fixture can cause injury or damage it if falls, attach an approved safety cable to one of the safety
cable attachment points on the base (see “Fixture overview” on page 6).
Check that all surfaces to be illuminated are minimum 200 mm. from the fixture, that combustible materials
(wood, fabric, paper, etc.) are minimum 100 mm. from the head, that there is free airflow around the fixture and
that there are no flammable materials nearby.
Make sure that it is impossible for the moving head to collide with another fixture or other object...
Fastening the fixture to a flat surface
The fixture can be fastened to a fixed flat surface that is oriented at any angle. Check that the surface can support at least
10 times the weight of all fixtures and equipment to be installed on it.
Warning! The supporting surface must be hard and flat or air vents in the base may be blocked, which will cause
overheating. Fasten the fixture securely. Do not stand it on a surface or leave it where it can be moved or can fall
over. Attach a securely anchored safety cable to the safety cable attachment point (see “Fixture overview” on
page 6) if the fixture is to be installed in any location where it may fall and cause injury or damage if the primary
attachment fails.
3. Block access under the work area. Working from a stable platform, hang the fixture on the truss with the
arrow on the base towards the area to be illuminated. Tighten the rigging clamp.
4. Secure the fixture against clamp failure with a secondary attachment such as an approved safety cable
that is rated for the weight of the fixture using one of the attachment points at the edges of the base (see
“Fixture overview” on page 6). Do not use any other part of the fixture as a safety cable attachment point.
5. Check that the head will not collide with other fixtures or objects.
10
Setup
Warning! Read “Safety Information” on page 3 before installing, powering, operating or servicing
the fixture.
Control panel and menu navigation
The onboard control panel and backlit graphic display are used to set the fixture's DMX address,
configure individual fixture settings (personality), read out data and execute service utilities. See “Onboard
control menus” on page 17 for a complete list of menus and commands.
Using the control buttons
l
To enter a menu, select a function or apply a selection, press ► (Enter).
l
Press ▲ (Up) and ▼ (Down) to scroll within a menu or adjust values.
l
To escape a function or move back one level in the menu structure, press ◄ (MODE).
Holding down the "UP" or "DOWN" button for more than 3 seconds, the MENU display rotated 180°
l
DMX address setting
The DMX address, also known as the start channel, is the first channel used to receive instructions from the controller.
For independent control, each fixture must be assigned its own control channels.
The DMX address is configured using the DMX ADDRESS menu in the control panel.
l
In order to facilitate for inspection the signal, If the display to flicker when it's not receiving any signalNotes
WDMX control
Press the button “UP” to switch off Wireless DMX or disconnect with all connected Transmitters.
Press the button “DOWN' to set the unit in the ”ready to connect with all not connected transmitters'
mode. If you press the mode button on the Wireless solution transmitter all the ready to connect units
will be connected.
If the unit is successfully connected in the home display the sign“
connected to a transmitter or switched off no“ ”. sign is visible
11
”. Appears. If the unit is not
CONTROL MODE
Standard and Manual modes
DMX control mode is selected in the CONTROL MODE menu. The fixture has tow DMX control
modes:
l
Standard
l
Manual
(Standard mode – uses 10 DMX channels)
mode (Extended mode – uses 4 DMX channels+manual zoom)
Dimming
DIMMER CURVE provides four dimming options (see picture below):
Optically linear
Square law
Inverse square law
S-curve
l
LINEAR – the increase in light intensity appears to be linear as DMX value is increased.
l
SQUARE LAW – light intensity control is finer at low levels and coarser at high levels.
l
INVERSE SQUARE LAW – light intensity control is coarser at low levels and finer at high levels.
l
S-CURVE – light intensity control is finer at low levels and high levels and coarser at medium levels. Whichever DIMMER
CURVE option you select, you can choose between NORMAL or SMOOTH dimming settings:
l
NORMAL is the default setting. It gives a virtually instantaneous reaction when you dim from one intensity to another,
but dimming slowly from one intensity to another may appear slightly uneven.
l
The SMOOTH setting gives smoother dimming during slow changes in intensity, but it limits the speed of dimming
changes slightly. This makes it ideal for slow, smooth dimming, but a short time-lag may be noticeable if you try to dim
quickly from one intensity to another.
l
Restoring factory default settings
The fixture factory default settings can be restored by applying a FACTORY SETTING → LOAD command.
12
Operation and effects
Warning! Read “Safety Information” starting on page 3 before installing, powering, operating or servicing the
fixture.
This section describes only DMX control features that require particular explanation. See “DMX protocols”on page 14 for
a full list of the DMX channels and values required to control the different effects.
Effects
Shutter effect
The electronic ‘shutter’ effect available for the Beam provides instant open and blackout,
variable speed regular and random strobe and opening/closing pulse effects as well as burst and sine wave effects.
Dimming
Beam and intensity can be adjusted 0 - 100% using electronic dimming. See the available dimming
curve options in “Dimming” on page 12
Zoom
The Beam can be zoomed from 58° to maximum (narrow) 11° one-tenth peak angles.
Controlling color
Color wheel effects
The electronic ‘color wheel’ effects available for the Beam give the convenience and feel of a mechanical color
wheel and let you snap between 33 different full LEE-referenced colors. You can also scroll continuously forwards
or backwards through the colors or display random colors at variable speed.
Color wheel priority
The color wheel effect channels for the Beam have priority and override any color set on the Beam RGBW
channels. To use the RGBW and RGB channels, you must set the color wheel effect channel for Beam to a
DMX value from 000 - 009. If you set either color wheel channel to a DMX value above 009, the color wheel
effect overrides RGBW or RGB control.
CTC (Color Temperature Control)
CTC is available for the Beam on the CTC channel 10. Setting this channel to DMX value 20 or above allows
you to adjust the Beam’ s overall color temperature, i.e. the color that has been set using the color wheel channel
or the RGBW channels. Note that the more saturated the color, the less it will be affected by adjustments in color
temperature. The biggest CTC variation is available when displaying white.
Overall color temperature can be varied from 10 000-2500K.The default color temperature is 5600K.
13
DMX protocols
Standard mode
Standard
DMX Value
Percent
Function
0 - 19
20 - 24
25 - 64
65 - 69
70 - 84
85 - 89
90 - 104
105 - 109
110 - 124
125 - 129
130 - 144
145 - 149
150 - 164
165 - 169
170 - 184
185 - 189
190 - 204
205 - 209
210 - 224
225 - 229
230 - 244
245 - 255
0-7
8 -9
10 - 25
26 - 27
28 - 33
34 - 35
36 - 41
42 - 43
44 - 49
50 - 51
52 - 57
58 - 59
60 - 65
66 - 67
68 - 73
74 - 75
76 - 81
82 - 83
84 - 89
90 - 91
92 - 97
98 - 100
Electronic shutter effect
Shutter closed
Shutter open
Strobe 1 ( fast → slow )
Shutter open
Strobe 2 : opening pulse ( fast → slow )
Shutter open
Strobe 3 : closing pulse ( fast → slow )
Shutter open
Strobe 4 : random strobe ( fast → slow )
Shutter open
Strobe 5 : random opening pulse ( fast → slow )
Shutter open
Strobe 6 : random closing pulse ( fast → slow )
Shutter open
Strobe 7 : burst pulse ( fast → slow )
Shutter open
Strobe 8 : random burst pulse ( fast → slow )
Shutter open
Strobe 9 : sine wave ( fast → slow )
Shutter open
Strobe 10 : burst ( fast → slow )
Shutter open
2
0 - 255
0 - 100
Beam Dimmer
0 → 100% intensity
3
0 - 255
0 - 100
Zoom
Wide → narrow
0-9
10 - 14
15 - 59
60 - 64
65 - 69
70 - 74
75 - 89
90 - 94
95 - 99
100 - 104
105 - 109
110 - 114
115 - 119
120 - 124
125 - 239
240 - 244
245 - 249
250 - 255
0-3
4-5
6 - 13
14 - 23
24 - 25
26 - 27
28 - 33
34 - 35
36 - 37
38 - 40
41 - 42
43 - 44
45 - 46
47 - 48
49 - 93
94-95
96-97
98 - 100
1
4
Fixture control settings
No function
Reset entire fixture 1
No function
Fan mode FULL 2
No function
Fan mode REGULATED 2
No function
Calibrated color output mode COLOR CALIB = ON 3
No function
Raw color output mode COLOR CALIB = OFF 3
No function
Fast dimming, speed of changes unrestricted 2
No function
Smooth dimming, speed of changes restricted slightly 2
No function
DMX Manual calibration mode 4
No function
Illuminate display
1 If DMX Reset is disabled in the menu, a reset command
can only be executed if channel 2 is set to 232 and channel
1 is setto zero. These values need to be held for 5 seconds
before feature is activated. Values must be "snapped to" to
function.
2 Menu override: setting unaffected by power off/on.
3 Value must be held for 3 seconds to activate. Setting
unaffected by power off/on.
4Please refer the page of 18.(calibrate by
DMX control)
Value must be held for 3 seconds to activate.
16
14
Standard
DMX Value
Percent
Function
Beem Color wheel effect
No function. RGBW color mixing enabled
Color wheel effect
Open
Color wheel rotation effect
Clockwise, fast → slow
Stop (this will stop wherever the color is at the time)
Counter -clockwise, slow → fast
Open
Random color
Fast
Medium
Slow
Open
0-9
10 - 174
175 - 179
0-1
2 - 67
68 - 69
180 - 201
202 - 207
208 - 229
230 - 234
70 - 78
79 - 80
81 - 89
90 - 91
235 - 239
240 - 244
245 - 249
250 - 255
92 - 93
94 - 95
96 - 97
98 - 100
0-255
0-100
Beam Red
Red 0 → 100%
0-255
0-100
Beam Green
Green 0 → 100%
8
0-255
0-100
Beam Blue
Blue 0 → 100%
9
0-100
0-100
Beam white
white 0 → 100%
10
0-19
20-255
0-07
8-100
Beam CCT
No Function
CTC 10 000K → 2 500K
5
6
7
Note: DMX values labeled "No function" will have no effect - the last functional value will be used.
15
Manual mode
Manual
DMX Value
Percent
1
2
3
4
Manual ZOOM
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0-100
0-100
0-100
0-100
0-100
Function
RED(0-255)
GREEN(0-255)
BLUE(0-255)
WHITE(0-255)
Wide → narrow
16
Onboard control menus
Menu
DMX ADDRESS
CONTROL MODE
STATIC COLOR
Item
Standard mode
Manual mode
DIMMER
RED
GREEN
BLUE
WHITE
ZOOM
STROBE
FANS
DIMMER MODE
DIMMER SPEED
PERSONALITY
DMX RESET
DISPLAY
WDMX
CALIBRATION
AUTO
EDIT
AUTO(1-10)
CUSTOM
TEST ALL
1.Scene
2.BEAM-red
3.BEAM-green
4.BEAM-blue
5.BEAM-white
6.BEAM-strobe
7.fade
8.time
9.ZOOM
10.use
Software type
INFO
Usage time
FACTORY SET
Temperature
LOAD
Notes (Default settings in bold print)
Options
1-XXX
0~255
0~255
0~255
0~255
0~255
0~20
0~255
REGULATED
FULL
LINEAR
SQUARE LAW
INV SQUARE LAW
S-CURVE
NORMAL
SMOOTH
OFF
ON
ON
30S
CONNECT
NO CONNECT
NO CALIBRATION
MANUAL
FACTORY
0~255
0~255
0~255
0~255
0~255
0~20
0~255
0~6.375 S
0~255
ON/OFF
V2.11
TOTAL
XXXX
RESET
Reset OK
XXX℃
17
Set DMX start address
10 DMX channels: Conrtol of beam
4 DMX channels: RGBW+manual zoom
0~100%
0~100%
0~100%
0~100%
0~100%
Wide → narrow
(0~20Hz)Select strobe frequency
Cooling fan speed thermostatically regulated
Max. cooling fan speed
Linear dimming curve
Square law dimming curve
Inverse square law dimming curve
S-curve dimming curve
Fast dimming with unrestricted speed
Smooth dimming with restricted speed
Disable reset via DMX
Enable reset via DMX
Display is always on
Display switches off and goes into Sleep mode if the
controls have not been pressed for 30 seconds
Connect to the WMDX
Disconnect and exit the WMDX
Color calibration mode off. the RGBW value is the orginal one.
Manual calibration mode, RGBW to white is custom calibration
Factory calibration mode,RGBW to white is Factory calibration.
10 Auto programs available
Choose custom programs
Test LEDs, zoom and display
Select the scene step
0~100%
0~100%
0~100%
0~100%
(0~20Hz)Select strobe frequency
transition time of last step to current step
(0~ 6.375 S ) step time
Wide → narrow
Enable or Disable scene
CPU firmware version
USE of time
Use time reset
LEDs current temperature
Return all settings to factory defaults
CALIBRATION
Three mode of color calibration
1, NO CALIBRATION
Color calibration mode off. the RGBW value is the orginal one .
2 , MANUAL
Manual calibration mode , RGBW to white is custom calibration.
Manual calibration can calibrate by control panel and DMX channel .
calibrate by control panel
Press"MODE,ENTER ,UP ,DOWN "four button to enter the calibration mode
Menu
Item
SETTING MENU
MANUAL
CALIBRATION
Want to quit?
Notes (Default settings in bold print)
Options
BEAM-red
BEAM-green
BEAM-blue
BEAM-white
YES/NO
000-255
000-255
000-255
000-255
calibrate by DMX control
channel 4 is set to 245-249 to enter dmx controller calibration
channel
DMX Value
Percent
1
2
3
0 - 255
0 - 255
0 - 255
0 - 229
230 - 234
240-244
245-249
250-255
0-100
0-100
0-100
0-100
0-89
90-95
96-97
98-10
4
5
6
7
8
9
0 - 254
255
0 - 255
0-255
0-255
0-255
0-99
100
0-100
0-100
0-100
0-100
Function
No function
No function
No function
No function
come back to DMX mode 5
No function
turn on manual calibration mode by dmx control 5
Illuminate display
5Value must be held for 3 seconds to activate.
No function
Save Correction, Value must be held for 3 seconds to activate.
RED(0-255)
GREEN(0-255)
BLUE(0-255)
WHITE(0-255)
3,FACTORY calibration mode
change tekst to:Fixture is calibrated in the factory. (done after production date june 2015)
18
Specifications
Physical
Length . . . . . . . . . . . . . . . . .
Width . . . . . . . . . . . . . . . . . .
Height . . . . . . . . . . . . . . . .
Weight . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
. . . . . . . . .
. . . . . . . . .
. . . . . . . .
. . . . . . . . . .
.
.
.
.
.
.
.
.
. . . . . . . . .
. . . . . . . . .
. . . . . . . .
. . . . . . . . . .
.
.
.
.
.
.
.
.
. . . . . . . . . . .
. . . . . . . . . . .
. . . . . . . . . .
. . . 5.5 kg without
. .260 mm
. .205 mm
. .326 mm
accessories
Dynamic Effects
color mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RGBW
color temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CTO, variable 10 000 - 2500 K
electronic 'color wheel' effect . . . . . . 21 LEE-referenced colors plus white, variable-speed
color-wheel rotation effect and random color
shutter effects . . . . . . . . . . . . . . . . . . . Electronic, with regular and random
pulse, burst and strobe effects
Electronic dimming . . . . . . . . . . . . . . . . . . . . . . four dimming curve options
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11° - 58° (one-tenth peak angle)
Optics
Light source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Osram Ostar high-power long-life emitters
Control and Programming
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DMX
DMX channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4/10
Setting and addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control panel with backlit graphic display
Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .. . . . . . .. . . . . . . . . . . . . . . . . . . . USITT DMX512-A
Construction
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Black
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High strength die-casting aluminum
Protection rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IP 20
Installation
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimum distance to combustible materials . . . . . .
Minimum distance to illuminated surfaces . . . . . . .
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
...................
. . . . . . . . . . . . . .
. . . . . . . . . . . . . .
.Indoor use only, must be
. . . . . . . . . . . . . . . . . . . .Any
. . . . . 100 mm. from fixture
. . . . . 200 mm. from fixture
fastened to structure or surface
Connections
AC power input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PowerCon input socket (blue)
AC power throughput. . . . . . . . . . . . . . . . . . . . . . . . . . .PowerCon
output socket (grey)
DMX data in/out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3/5-pin locking XLR
19
Electrical
AC power . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . .100-240 V nominal, 50/60 Hz
Maximum total power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140 W
Power supply unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .Auto-ranging electronic switch mode
Power consumption, all effects static, zero light output . . . . . . . . . . . . . . . . . . . . . . . . <15 W
Thermal
Cooling . . . . . . . . . . . . . . . . . Forced air (temperature-regulated, low noise, user-definable levels)
Maximum ambient temperature (Ta max.). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C
Minimum ambient temperature (Ta min.). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5° C
Total heat dissipation (calculated, +/- 10%) . . . . . . . . . . . . . . . . . . . . . . . . . . .820 BTU/hr.
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising