UltraCut® 40E - Snap
UltraCut®
40E
Model No. 28PCA40E
State of the
art technology at
your finger tips
Portable Inverter Air Plasma Cutter
Inverter high frequency 220V (50/60Hz) with variable
output control. Maximum 40A output at 60% duty cycle.
Cuts stainless steel, copper, iron and aluminum
up to 1/2 inch (13mm) thick.
Severe cut 5/8 inch thick (16mm)
Metal plates with different thickness
can be curve-cut into any shape
“Easy touch” smooth start
Air regulator with water separator
for longer tip life included
Fan assisted air-cooling with
temperature overload protection
Comes with a back up pack
of tips and nozzles
Compact cabinet
15” x 6” x 12” (371 x 155 x 295mm)
Lightweight
(only 18lbs / 8kg)
Fully compliant with:
EMC directive 73/23/EEC and 89/336/EEC
European Standard: EN/IEC60974-1
Plasma Cutting Process
Plasma cutting is a process that is used to cut steel and other metals of
different thicknesses (or sometimes other materials,) using a plasma torch.
In this process, compressed air is blown at high speed out of a nozzle; at
the same time an electrical arc is formed through that gas from the nozzle
to the surface being cut, turning some of that gas to plasma. The plasma is
sufficiently hot to melt the metal being cut and moves sufficiently fast to blow
molten metal away from the cut.
The HF Contact type uses a high-frequency,
high-voltage spark to ionize the air through the
torch head and initiate an arc. These require the
torch to be in contact with the job material when
starting.
Plasma is an effective means of cutting thin and
thick materials alike. Since plasma
cutters produce a very hot and very localized
“cone” to cut with, they are extremely useful for
cutting sheet metal in curved or angled shapes
The UltraCut® 40E include an air filter regulator who not
only provides a clean and dry air, but also ensures the steady
pressure of the air source.
Specifications:
Rating flow: 550 L/min
Applicable pressure range: 0 ~ 1,0 Mpa
Applicable temperature: 0 ~ 60°C
Accessories
and Specifications
Accessories
• Spare ceramic
nozzle (diffuser):
197070002E
• Spare electrode:
047070004E
• Spare copper
cutting tip:
057070004E
• Spare ceramic
insulator ring:
197070004E
• Cutting gun cable assembly, ground
clamp cable assembly, filter regulator
and reinforced hose included
Equipment Specifications
• Input voltage
220V AC ± 10%
• Input frequency
50Hz / 60Hz
• Input capacitance
6 KVA
• No-load voltage
230V
• Current range
20-40A
• Output Voltage
96V
• Rated duty cycle
60%
• Efficiency85
• Power factor
0.93
• Insulation class
B
• Protection class
IP23
• Arc starting
Contact arc starting (pilot arc)
• Air flow
0.17 m3/min
• Maximum cutting thickness
13mm
• Weight
18lbs (8kg)
• Size (L x W x H)
15” x 6” x 12” (371 x 155 x 295mm)
Snap-on Equipment · Blackhawk / 309 Exchange Avenue / Conway, Arkansas 72032 U.S.A.
Fax: 501-450-2085 / Toll Free: 1-877-482-4866 / www.blackhawkcr.com
Blackhawk is committed to product innovation and improvement. Therefore, specifications listed in this brochure may change without
notice. ©2015 Snap-on Incorporated. Blackhawk® is a registered trademark of Snap-on Incorporated. UltraCut is a registered
trademark of A.M.H. Canada Ltee Corporation. All Rights Reserved.
08/15
SS143401A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising