INSTRUCTION MANUAL
Thanks for your choice of heart rate monitor with
pedometer. It has such features:
1
H EA RT RATE MO N ITO R WITH P ED O M ETER
I N S T R U C TI ON MA N U A L
FUNCTION INTRODUCTION
●Accurate wireless heart rate measurement.
●Display the percentage of real heart rate value to
maximum heart rate value based on different age
●Heat rate value, maximum HR (heat rate) value, average
HR value
●Record the exercise time and the exercise calorie
consumption
●Set maximum heart rate and low heart rate alarm
●Step counting, Calorie, Distance, Exercise Time
●Clock, calendar,12H/24H
●Alarm
●Timer
●Stopwatch
●EL Backlight
●5.3KHZ Transmitter belt
●6 days memory record,
2
3. RESET
-Decrease the figure value when setting
-Switch function display in each mode
4. LIGHT
-Turn on the EL backlight
LIGHT
-It will switch off backlight
automatically if not
pressing the key within
3seconds.
MODE
3
4
Memory
RESET
HOW TO USE THE BACK LIGHT
5 CLOCK, CALENDAR SETTING
1.In mode of "Calendar/Clock/Week" , press MODE for 2
seconds to enter into the setting of clock and calendar.
The setting icon will flash, press START to increase the
value, or press RESET to decrease the value. Press
MODE again to confirm the setting and proceed to next
setting, hold MODE 2 seconds to quit the setting mode.
The setting sequence is as Fig.2.
MODE
12H/24H
Calendar/clock/week
MODE
MODE
MODE
Day
Chronometer
RESET
Average HR./heart rate
Alarm
Height
Fig.4
3. Set maximum heart rate and low heart rate alarm
In” Exercise time/Heart rate “mode , hold MODE for 2
seconds to enter into setting maximum HR and low HR
alarm . Refer to FIG 5
hold MODE
for 2
seconds
Fig.3
2.Setting user's personal parameters.
When first use the heart rate monitor, set user's personal
parameter. Or else, the heart rate percentage, calorie
consumption will be incorrect. In SETUP mode , hold
MODE for 2 seconds to enter into setting parameters ,
press START to increase the value, or press RESET to
decrease the value. Press MODE again to confirm the
setting and proceed to next setting, hold MODE 2 seconds
to quit the setting mode. Refer to FIG 4.
Setup
Excise time
/heart rate
MODE
Maximum heart rate alarm
Low heart rate alarm
MODE
MODE
4
Gender
Fig.6
1)The transmitter belt is used to measurement your heart
rate and transmit the data to the receiver that inside
heart rate monitor. Refer to Fig 6 to wear.
2)Strap the belt across your chest. Adjust the strap until
the transmitter sits snugly below the pectoral muscles
for an accurate heart rate signal.
3)The max. distance between Heart rate monitor and
transmitter belt is 80cm.
6.Recall Heart rate record
1)In MEM mode press START to recall the memory. It will
display max heart rate and calorie. Press RESET to
display other recorded memory. There are 6 days heart
rate and calorie memory.
2) Each day's steps and calorie will be recorded
automatically at the time of 0: 00.00( 24H) /
AM12:00.00(12H). Meanwhile, the pedometer's steps
/time /distance /calorie will be reset to zero.
7
Heart rate alarm on/off
Fig.5
Unit setting
Month
Year
Fig.2
Timer
3
RESET
MODE
Weight
Calorie/heart rate
Maximum HR./heart rate
hold MODE
for 2
seconds
MODE
MODE
RESET
Age
RESET
Minute
MODE
2
RESET
HR. percentage
/ heart rate
Hour
Steps counting
Heart rate
MODE
MODE
Excise time
/ heart rate
MODE
MODE
1. OPERATION MODE
Refer to FIG 3 to switch different heart rate modes.
RESET
Setup
Refer to Fig 1 to switch from one mode to another.
MODE
HEART RATE MEASUREMENT
Fig.1
2.In mode of "Calendar/Clock/Week" , press START to turn
on/off hourly chime signal.
OPERATION MODE
1
6
MODE
START
Press LIGHT to turn on the back light, which will last for 3
seconds. It will switch off backlight automatically if not
pressing the key within 3seconds.
OPERATION BUTTONS
1. MODE
- Change over the modes
- Hold 2 seconds to enter setting or quitting the setting
mode
- Change over setting value
2. START
- Increase the figure value when setting
- Start/Stop chronograph running
- Recall the memory
MODE
4. CLEAR TO ZERO
In Exercise time/Heart rate, Maximum Heart rate,
Calorie/Heart rate mode , hold RESET for 2 seconds to
clear data to zero.
5. THE TRANSMITTER BELT
5
Steps
Distance
RESET
Calorie
6
Fig.7
hold MODE
for 2
seconds
MODE
Unit setting
Setup
Gender
MODE
MODE
MODE
Weight
Age
STEPS COUNTING
1.OPERATION MODE
Refer to Fig. 7 to changeover the different steps counting
mode.
2. In Step, Distance, Time ,Calorie mode , hold RESET for
2 seconds to clear data to zero.
3.LB/INCH or KG/CM and Step parameters setting.
Time
MODE
Stride
Fig.8
7
Height
When first use the pedometer, set user's personal
parameter. Or else, distance, calorie consumption will
be incorrect. In SETUP mode , hold MODE for 2 seconds
to enter into setting parameters the character "KG CM"
will flash. Press START to increase the value, or press
RESET to decrease the value. Press MODE again to
confirm the setting and proceed to next setting,hold
MODE 2 seconds to quit the setting mode Refer to FIG 8.
4. Walking stride is always different. You can calculate the
average and input to the pedometer. For example, when
you take 10 steps, the total length is 6m,the average
stride will be 60cm.See Fig.9.
8
6.Recall Steps Record
(1)In MEM mode press START to recall the memory. It will
display steps and calorie. Press RESET to display
other recorded memory. There are 6 days steps and
calorie memory.
(2)Each day's steps and calorie will be recorded
automatically at the time of 0: 00.00( 24H) /
AM12:00.00(12H). Meanwhile, the pedometer's steps
/time /distance /calorie will be reset to zero.
hold MODE
for 2
seconds
Alarm
MODE
ALARM
Fig.10
1.How to set the alarm
In the mode of "Alarm", hold MODE 2seconds to enter to
set the alarm. The setting figure will flash, press START
to increase the value, or press RESET to decrease the
value. Press MODE again to confirm the setting or hold
MODE 2 seconds to quit the setting mode. Refer to FIG
10.
2.Turn on/off the alarm
In the mode of "Alarm" ,press the button START to turn
on/off the alarm. When the alarm is on, it will display “
“and will beep 30 seconds when reach to the preset
time everyday. Press any button to release the alarm.
When the alarm is off, it will NOT display “
“
10
9
NOTE: ●The battery anode should be upwards..
● Please replace the battery in time when the
display becomes dim.
● If no display or dysfunctions after replace
new battery, please take the battery out.
After 15 seconds or use the plier to make the
battery anode and cathode clips short, then
please reinstall the battery.
RESET
Fig.12
2)Each day's steps and calorie will be recorded
automatically at the time of 0: 00.00( 24H) /
AM12:00.00(12H). Meanwhile, the pedometer's steps
/time /distance /calorie will be reset to zero.
13
BATTERY REPLACE
a.Unscrew the
bottom case.
d.Put in the
new battery.
b.Remove the
bottom case.
e. Screw the
bottom case.
12
c.Take out the
old battery.
Second
Fig.11
2)Countdown timer
In mode of "Timer", press START to start counting down.
Press START again to stop counting down. Hold RESET
for 2 seconds to reset the timer to 00:00:00.
3)When the timer reset the timer to 00:00:00, press START
to start counting up .Press START again to stop counting
up, hold RESET for 2 seconds to reset the timer to
00:00:00.
11
COUNTDOWN TIMER
1)How to set the countdown timer
In mode of "Timer", press MODE and hold 2 seconds to
enter timer setting. Press START to increase the value,
or press RESET to decrease the value. Press MODE
again to confirm the setting and proceed to next setting ,
hold MODE 2 seconds to quit the setting mode. The
setting sequence is as FIG11.
RECALL PULSE RECORD
1)In mode of "MEM", press START to recall the memory. It
will display maximum HR (heat rate) value, average HR
value and the exercise calorie consumption, press
START to display other days recorded memory. There
are 6 days recorded memory. Each sequence number
has the related date. See FIG12
RESET
按2秒
MODE
SPECIFICATION
1.Clock and Calendar
Date and Time format: Hour, Minute, Second, Year,
Month, Week, Day, 12/24H
100 years calendar:2000~2099
Alarm:1 daily alarm(hour: minute)
2.Chronometer
Range:0:00:00~ 59minutes:59seconds:99~ 99hours:59
minutes: 59seconds.
In first 1hour,it is measured display in 1/100 seconds.
3.Countdown Timer
Countdown Timer:99hour59 minutes 59 seconds.
4.Steps Counting Mode: Steps/Clock, Steps/ Time,
Distance/Calorie
Steps range:0~999999
Time:0:00:00~99H59M59S
Distance:0.00~999.99KM(or 0.00~999.99 Mile)
Calorie:0.0~9999.9KCAL
Memory:6 memories. Each memory include
steps/calorie and related date.
13
RESET
MODE
Memory
8
12
Minute
Clock
Countdown
Maximum heart rate
MODE
MODE
Alarm on / off
9
Fig.9
5. Auto start/stop. The pedometer will only calculate the
exercise data that over 10 times. For example, if you
walk less than 10 steps, there will be no change for
steps, time and calorie. Such design is to ensure the
accuracy in case of discontinuous exercise.
HOW TO USE THE CHRONOMETER
In the mode of "STW”:
1)Press the button START to start chronometer running,
press START again to stop. Hold RESET for 2 seconds to
reset the chronometer to zero.
2)When the chronometer is running, press RESET to get
the current split time. Then press START again to stop
chronometer .
3)During chronometer running, press RESET to get
current split time; when stop exercise, Press RESET to
get the LAP1-LAP9 split time.
Hour
Minute
10
5.Personal Data
Stride:25cm~150cm
Default is 50cm
Or 10inches~60inches Default is 20inches
Weight:20kg~200kg
Default is 70kg
Or 45lbs~440lbs
Default is 154lbs
Height:90cm~240cm Default is 170cm
Or 35inches~95inches Default is 67inches
Age:10~99
Default is 30
Sex:Male, Female
Default is Male
6.Heart Rate Measurement
Heart Rate Range:30~240bpm
Resolution:1 bpm
Accuracy: ±1 bpm
7.Environment
Operation Temperature:0℃~+50℃
Storage Temperature:-5℃~ +60℃
Humidity:10%~95%
8.Water Resistance: 30M water-resist
NOTE: Water-proof tested and the product can be in
good condition under 30m water when you
don't operate it. It is suggested to NOT wear
the watch during swimming or taking shower.
9.Battery: 1 pcs CR2032 Lithium battery
14
1st day date
11
Average heart rate
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising