hs667-24 linear actuator

hs667-24 linear actuator
Ventilation Systems
HS667-24 LINEAR ACTUATOR
General Installation Notes:
Make sure that power is disconnected from system prior to servicing.
Installation of this equipment and related OEM equipment should be in accordance with these instructions,
OEM’s installation instructions and local codes (if applicable). Failure to follow specified instructions may cause
damage to equipment and/or personal injury or death.
Take special note of any Warnings or Safety Decals on the equipment and in manuals.
Always wear protective clothing and any applicable Personal Protective Equipment (Safety Glasses and/or Ear
Plugs) when working with the equipment.
Discarded materials, equipment and boxes should be recycled in accordance with local and national codes.
Note: Linear Actuator Assembly is to be wired in accordance with all applicable local and national electrical wiring codes. All wiring sizes and fuse
capacities are to be sized according to applicable electrical code specifications or other regulations.
Safety Instructions:
Read all safety messages in this manual and on equipment safety decals. Follow recommended precautions and
safe operating practices.
Ground all electrical equipment for safety.
Ground all non-current carrying metal parts to guard against electrical shock.
Always keep safety decals in good condition and replace missing or damaged decals.
Overview:
The Hog Slat Linear Actuator Assembly is designed to be used with automatic ventilation control. This unit
provides bi-directional control with potentiometer feedback for position sensing.
Electrical Specifications:
Model#
Voltage Rating
Amp Rating (watts)
Frequency
HS667-24
120 VAC
1.4A (167W)
60 Hz
HS667-24-240
240 VAC
.8 A(167W)
50/60 Hz
Position sensor:
10K Ω potentiometer: .650Ω to 6.4KΩ (Closed to Fully Extended) output range
Max Duty Cycle:
20%, 12 min / hours
Hog Slat Inc. Newton Grove, NC USA August 2016
1
Ventilation Systems
Mechanical Specifications:
Max Load:
350 Kgs / 772 lbs
Max Speed:
6.3mm / 1/4” per second @ 60Hz or 5.4mm/ 7/32” per second @ 50 Hz.
Stroke Length: 610mm / 24”
HS667-24 SERIES LINEAR ACTUATOR ASSEMBLY (see Figure 1)
REF#
PART #
DESCRIPTION
1
HS633
ENCLOSURE ASSEMBLY, LINEAR ACTUATOR
2
HS667-24
LINEAR ACTUATOR, 120 VAC @ 60Hz
OR
HS667-24-240
LINEAR ACTUATOR, 240 VAC @ 50/60 Hz
Installation:
1. Determine mounting configuration.
2. Position and secure mounting bases to linear actuator extension tube with supplied hardware. Place
mounting bases at approximate distances as shown along extension tube.
3. Secure Linear Actuator machine to wall or ceiling using (8) 5/16” x 2” lag bolts provided Figure 1 or optional
mounting plate shown in Figure 2.
4. Wire actuator to control device. (See Figure 3 and 4)
Optional
mounting base
with hardware
HS667-01
Secure
mounting
bases using
5/16 x 2” lag
bolts
Figure 1
Figure 2
Hog Slat Inc. Newton Grove, NC USA August 2016
2
Ventilation Systems
5. To set “OPEN” limit of actuator, run actuator (open or extend) until desired opening is achieved (maximum
24”). Once “OPEN” position has been reached, disconnect power from unit so that local limit switch can be
set.
6. Remove (4) screws from the end of the actuator located at the motor end and remove cover to gain access to
Adjustment Wheel.
Screws
7. Adjust “OPEN” limit by loosening (2) screws as shown below and turn “Adjustment Wheel”. Adjustment
Wheel rotates CCW when actuator extends shaft. To set “OPEN” limit, set “Adjustment Wheel” bump to the
right of the switch button as shown below. Rotate adjustment wheel CCW until it just actuates switch.
8. Re-tighten “Adjustment Wheel” screws.
9. Manually run machine in “CLOSE” direction for approx. 6” and then in “OPEN” direction to verify “OPEN” limit
is in desired position. Re-adjust wheel as required.
10. “CLOSED” limit is factory set and is not adjustable. Any attempt to adjust could result in permanent damage to
linear actuator.
Loosen screws to adjust
wheel.
Rotate “Adjustment Wheel”
CCW until bump just contacts
limit switch pin.
SCREWS
Hog Slat Inc. Newton Grove, NC USA August 2016
3
Ventilation Systems
ENCLOSURE WIRING IDENTIFICATION (FIGURE 3)
Hog Slat Inc. Newton Grove, NC USA August 2016
4
Ventilation Systems
WIRING SCHEMATIC (FIGURE 4)
.650Ω to 6.4K Ω
/ L2
Hog Slat Inc. Newton Grove, NC USA August 2016
5
Ventilation Systems
NOTES
-------------------------------------------------------------------------------------------------------------------------------------------
Hog Slat Inc. Newton Grove, NC USA August 2016
6
Ventilation Systems
Intentionally Left Blank
Hog Slat Inc. Newton Grove, NC USA August 2016
7
Ventilation Systems
This equipment must be installed in accordance with all State and
Local Codes and applicable Regulations which should be followed in
all cases. Authorities having jurisdiction should be consulted before
installations are made.
Hog Slat, Inc.
PO Box 300
Newton Grove, NC 28366
Phone: (910) 594-0219
Fax: (910) 594-1392
www.hogslat.com
Copyright © 2016 by Hog Slat, Inc.
Part Number: HSManual-030 Rev A7
HSART-270
Market – Hog & Poultry
Hog Slat Inc. Newton Grove, NC USA August 2016
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising