Installation, Operating and Servicing Instructions Silverlink

Installation, Operating and Servicing Instructions Silverlink
Installation, Operating and Servicing
Instructions
Silverlink 600 Electric Boiling Tops
HT3, HT6, HT7
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________
IS 220 ECN 3607
Page 1 of 7
CONTENTS
Important Information
Warnings and Precautions
Technical Data
Checklist of Enclosures
Installation and Commissioning
Operating Instructions
Cleaning
Servicing, Maintenance and Component Replacement
Fault Finding
Spare Parts List
Service Information and Guarantee
2
3
3
3
3-5
5
5
5
6
6
7
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE
IS 220 ECN 3607
Page 2 of 7
WARNINGS AND PRECAUTIONS
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
TECHNICAL DATA
Model
HT3
HT6
HT7
Height (mm)
290
Width (mm)
300
600
750
Depth (mm)
600
Weight (kg)
10
17
19
CHECK LIST OF ENCLOSURES
Warranty card
Instructions manual
INSTALLATION AND COMMISSIONING
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other
equipment.
If replacing the plug connect the terminals as follows:
Green and Yellow wire Earth
E
Blue wire
Neutral N
Brown wire
Live
L
IS 220 ECN 3607
Page 3 of 7
Means of isolation with at least 3mm contact separation in all poles must be
incorporated into the fixed wiring of this appliance.
The fixed wiring insulation must be protected by insulated sleeving having a
temperature rating of at least 60 Deg C.
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)
Install this appliance on a level surface ensuring all vents are unobstructed. Any
partitions, walls or furniture must be of non-combustible material. Minimum
distances A 100mm B 1000mm – see Fig 1.
Fig 1
IS 220 ECN 3607
Page 4 of 7
Power Ratings
Model
HT3
HT6
HT7
kW
3.0
7.0
7.0
Electrical supply 1N~+E
13.0
30.5
30.5
Electrical supply 3N~+E
N/A
L1 2 L2 3 L3 2
L1 2 L2 3 L3 2
Appliances above 3kW must be connected to the electricity supply by a qualified
electrician.
OPERATING INSTRUCTIONS
Only qualified or trained personnel should use this appliance.
Connect the appliance to the electricity supply and switch on – the green neon
illuminates to indicate power to the appliance.
On initial use, heat the hotplates on maximum without a pan for 3-5 minutes to burn
off their protective coating.
The hotplates can then be regulated by their relevant control knob.
Each hotplate incorporates a protection device that reduces the power automatically
when a pan is removed.
CLEANING
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent, do not use abrasive
materials. Dry with a soft cloth.
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
All servicing, maintenance and component replacement on this appliance should be
carried out by one of our recommended service engineers.
IS 220 ECN 3607
Page 5 of 7
FAULT FINDING
Please refer to the Service Help Desk number on the final page of this manual.
SPARE PARTS LIST
Part Number
FE37
FI10
HO10
HO11
KN180
NE43
PL202
SW14
IS 220 ECN 3607
Description
Foot
Fixing plate
2kW hotplate
1.5kW hotplate
Control knob
Neon
Plug and lead
Switch
Page 6 of 7
Used on
All
All
HT6, HT7
All
All
All
HT3
All
SERVICE INFORMATION
For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:
 UK:
01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:




Brief details of the problem
Product code
All available on serial plate
Type number
Serial number
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is
in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:



Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance with the
conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for
within the warranty. Any requirement for staff attending the call to spend greater time
than 15 minutes due to administrative requirements, such as on health and safety risk
assessments, will be chargeable at the prevailing rate.
IS 220 ECN 3607
Page 7 of 7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising